环境温度宽范围变化对光纤布里渊频移的影响

搭建了光纤布里渊频移测量系统,实现了色散位移光纤20 ℃到820 ℃布里渊频移的测量,并对测量数据进行拟合. 在环境温度大范围变化时,目前采用的布里渊频移-温度一阶线性关系式对测量数据分析误差较大,针对这个问题,本文从纯石英光纤的结构特点和材料的物性系数出发,在分析光纤的热膨胀系数、光纤密度、折射率、弹性模量和泊松比与宽范围温度关系的基础上,根据布里渊频移与各物性参数的关系式理论推导了宽范围温度变化与布里渊频移之间的二次项关系式. 理论推导结果与实验数据基本符合,验证了理论分析的正确性,从而为光纤宽范围布     

用于测量海水温度和压力光纤传感器

文章从理论上分析了布里渊散射光的频移和强度与海水温度和应力的关系,针对分布式布里渊散射光纤传感器测量海水温度和压力的测量原理进行了论述,对该测量系统的构成以及测量的实现进行了探讨。     

新型声速剖面仪通过技术鉴定

海军海洋测绘研究所与无锡海鹰加科公司协作研制的ＨＹ12 0 0系列声速剖面仪 ,于 2 0 0 2年 8月通过海军装备部门组织的技术鉴定。声速剖面仪是一种测量声波在水中传播速度的精密水声仪器。它采用环鸣法直接测量声信号在固定距离内的传播时间得到声速 ,同时通过温度及压力传感器测量温度和垂直湿度。能快速、有效、方便地为测深仪等声纳设备校正测量误差 ,提供实时的声速剖面数据。该系列声速剖面仪有两个类型 :Ａ型为电缆式 (水深 10 0ｍ以内 ) ,可选计算机或掌上机作为水上终端 ;Ｂ型为自容式 (2 0 0ｍ ,可扩展 ) ,内装不挥发存储器 ,可存…     

一种提高深远海全深度声速剖面重构精度的方法

开展多波束水深测量应同步进行声速剖面探测。因海上作业条件恶劣、作业时间受限及设备性能局限等影响,在深远海海域常获取不到全深度的实测声速剖面。尽管利用温盐场模型可将声速剖面直接延拓至实地水深的最大深度,但这种气候态平均声速剖面与实际的声速剖面间存在不可控的系统性偏差,会给声速改正及水深测量成果带来质量隐患。给出了一种提高深远海全深度声速剖面重构精度的方法,即利用有效探测深度附近的实测温度盐度值,对大于有效探测深度的各水层的模型温度盐度值施加程度不一的约束控制。结果表明,经优化后全深度声速剖面的重构精度得到明显提高,其中2个XCTD站点声速剖面的互差SSPD分别由-2.5～1.0 m/s优化为0.0～1.0 m/s、0.0～2.6 m/s优化为-1.5～0.0 m/s; 2个CTD站点声速剖面的互差SSPD分别由-0.5～1.7 m/s优化为-0.4～0.3 m/s、-2.15～0.8 m/s优化为-1.4～0.8 m/s。     

印尼海啸区附近海域沉积物声速测量及声学特性分析

介绍了沉积物柱状样超声透射法测量方法和原理.对印尼海啸区附近海域沉积物柱状样进行了现场测量,通过测量数据的处理和分析,给出了沉积物的垂向声速剖面.讨论了声速与频率的关系,指出声速具有随频率的0.1次方增大的频散特性.分析沉积深度、结构以及生物扰动等方面的因素对声学测量结果的影响,结果表明海底地震引起的沉积物变迁、沉积物结构扰动、气体的混入等对声速的测量结果均产生影响.     

CNSVPGets软件获取声速剖面精度分析

提出最大差、中误差和全程平均差作为声速剖面曲线比较的精度指标。使用CNSVPGets软件对218条实测声速剖面曲线与软件获取剖面曲线进行对比计算,统计了比对曲线的最大水深、最大差、中误差、全程平均差;全部对比曲线的平均水深为1231.36m,平均最大差为6.74m/s,平均中误差为2.68m/s,全程平均差为1.72m/s。全程平均差小于5m/s的对比剖面对占95.4%,由此推论软件获取声速剖面的全程平均差极限误差为5m/s,中误差为2.5m/s;用软件获取声速剖面取代实测剖面用于水深测量计算,对测深精度的影响比海道测量规定的深度测量极限误差低1个数量级,因此可以使用软件获取声速剖面用于海道测量的深度测量声速改正。基于软件获取声速剖面的效率和重要性提出了建立和维护中国的全球声速剖面模型的建议。     

Biot反演在夏威夷钙质沉积物原位测量声速和衰减中的应用

对夏威夷檀香山岛的两个站(H3和H4)钙质沉积物进行了20～100kHz的原位纵波声速和声衰减测量.它们均有轻微的频散.随频率的增加H3站位声速从1691m/s增加到1708m/s,H4站位的声速从1579m/s增加到1585m/s.随频率的增加H3站位的有效衰减从15dB/m增加到75dB/m,H4站位的有效衰减从22dB/m增加到62dB/m.运用Biot-Stoll模型对所测得的纵波速度和声衰减数据进行了Biot模型未知参数反演,发现粒径较大的H3站的沉积物(孔隙率为45%)比粒径较小的H4站的沉积物(孔隙率为56%)具有曲率小和渗透率及孔隙半径都大的性质.     

计及复杂海洋环境适应性的海缆敷设故障特征提取模型构建

海缆作为连接海上风电场和陆上集中控制中心的“纽带”,承担着整个风电场的电力传输和通信任务。本文以实时监测海缆运行状态、提高海缆故障诊断效果为目标,构建计及复杂海洋环境适应性的海缆敷设故障特征提取模型。本文基于复杂海洋环境对海缆敷设的影响,分析布里渊频移与电缆温度、应变的关系,构建三者之间的线性方程;结合拉曼散射信号的温...     

基于多波束测深仪的西太平洋声散射层测量

为了研究西太平洋声散射层的垂向分布特征和日变化规律,分析了多波束测深系统的水体影像数据。观测结果表明,西太平洋存在着两个声散射层,一个声散射层位于0～200 m,另一个声散射层位于500～700 m,两个声散射层散射强度具有明显的日变化特征,上层散射层的散射强度呈现白天弱,夜晚强的特征,而下层散射层的散射强度日变化规律与上层相反,并且发现深散射层的厚度也存在日变化特征;分析了此种方法的优缺点,对以后声散射层的观测分析提供了新的思路。此外,利用同时下放的声速仪(SVP)的温度和深度数据对下放式声学多普勒流速剖面仪(LADCP)的观测结果进行了修正,得到了更为精确的声散射层垂向位置分布。     

基于多波长激光吸收光谱技术的气体浓度与温度二维分布遗传模拟退火重建研究

利用可调谐半导体激光吸收光谱技术实现气体浓度温度二维分布重建.设计了气体浓度温度二维分布重建测量系统,采用四路波分复用技术以减少投影光路布置数量和增加气体吸收测量信息.针对于图像重建过程中建立的非线性投影方程组,将遗传算法与模拟退火算法相结合进行求解,在实现全局最优搜索基础上提高算法搜索效率.建立燃烧环境下H₂O浓度温度二维分布模型,借助于近红外波段1.3—1.5 μm范围内4条H₂O气体吸收谱线,利用数值模拟计算方法进行了气体分布重建,重建结果与模型符合得很好     

Microbial Biomass and Organic Nutrients in the Deep-Sea Sediments of the Central Indian Ocean Basin

In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance.     

Assessing the Validity of Seismo-Acoustic Predictor Equations for Obtaining Seabed and Sub-Surface Sediment Physical Properties

The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths.     

A Review of Some Environmental Issues Affecting Marine Mining

This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested.     

Increased Particle Fluxes at the INDEX Site Attributable to Simulated Benthic Disturbance

Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement.     

海上大直径钢管桩打桩过程中桩周土强度弱化研究

海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。     

Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification

An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm.     

Determination of In Situ Sediment Shear Strength from Advanced Piston Corer Pullout Forces

The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments.     

Interannual Sea Level Variations and Annual Tides in the Northwestern Pacific

Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone.     

《Acta Oceanologica Sinica》Vol. 33(2014) contents

<正>~~