半潜式平台垂向运动低频响应特性

对半潜式平台垂向运动性能(包括垂荡、横摇和纵摇)进行数值计算分析。与模型试验结果的比较表明,对于半潜式平台这类由柱体组成的结构物进行水动力数值预报,忽略粘性力作用会使得低频运动响应计算结果产生偏差,需要应用三维势流理论和Morison公式相结合的方法。横摇和纵摇运动固有频率均低于波浪频率,在波浪慢漂力作用下会出现显著低频运动响应。垂荡运动是否出现低频响应则与所处海况联系紧密。     

波频和慢漂组合作用下钢悬链线立管疲劳损伤研究

为了有效地考虑浮体慢漂运动对钢悬链线立管疲劳损伤的影响,提出了波频和慢漂运动组合作用下钢悬链线立管疲劳损伤简化计算的位置组合叠加法。其核心是:基于浮体慢漂运动概率分布选取若干典型慢漂位置,进行波频运动作用下钢悬链线立管动力响应分析;根据钢悬链线立管运动位置变化特征,截取若干慢漂位置对应的波频应力时程叠加到慢漂应力时程上,得到波频和慢漂运动的组合应力时程;编写基于雨流计数法的MATLAB程序处理立管各节点应力,采用海水环境下Do E.E型S-N曲线和Palmgren-Miner累积损伤准则计算立管各节点疲劳损伤。应用位置组合叠加法对某海域500 m水深的立管进行了疲劳分析,并与全耦合法、权重组合叠加法以及波频和慢漂疲劳损伤简单相加法的结果进行了对比,结果表明该方法具有较高的精度和效率。此外,进行了区域设定系数、波浪高度、波浪周期和土壤表面剪切强度等参数对组合作用下立管疲劳损伤的敏感性分析。     

顺应式海洋平台慢漂运动物理模型试验研究

为研究顺应式海洋平台慢漂运动的影响因素,以截断圆柱和漂浮方箱为例进行了不规则波作用下的慢漂运动模型试验。测量了不同系泊刚度条件下的漂浮方箱以及相同系泊刚度条件下的截断圆柱和漂浮方箱在静水中自由衰减运动和在不规则波中的运动响应,并将运动响应分解成一阶波频运动响应和二阶低频运动响应,分析了系泊刚度和浮体形状对浮体运动的影响。通过物理模型试验发现了系泊刚度及浮体形状对顺应式系泊浮体一阶运动标准差和二阶低频运动平均漂移值和标准差的关系。结果表明由于顺应式浮体的固有周期远离波浪谱峰周期时,系泊刚度以及浮体形状对慢漂运动的一阶运动响应影响不大;二阶低频运动相对偏离平衡位置的平均值和标准差均随系泊刚度增大而减小,浮体形状同样对慢漂运动的二阶低频纵荡运动响应影响较大。试验结果为实际海洋工程的外形选择和系泊刚度选择提供数据支持。     

浮式塔的动力计算

采用频域二阶摄动法研究了浮式塔在给定环境条件下的动力响应.计算了浮式塔在不规则波上的一阶运动响应函数和运动谱以及张力谱,同时进行了相应的模型试验.由结果的比较可以看出,试验结果与理论方法计算得到的结果吻合较好.计算结果表明,波浪的二阶作用对浮式塔的低频纵荡有影响.计算结果与试验结果的比较说明频域二阶摄动法可以用于浮式塔的动力分析.     

扁平潜器微速操纵性研究

针对扁平潜器的特点建立了其微速操纵性运动方程,提出了忽略攻角、漂角与旋转角速度耦合影响的水动力模型,由拖曳水池模型试验确定了攻角、漂角水动力,近似估算了旋转水动力.在主辅推进器的PD控制下,数值仿真计算了水平面航向保持与改变、垂直面潜浮的微速运动控制.     

大深度载人潜水器低速大漂角模糊滑模航向控制研究

通过模型试验测量大深度载人潜水器低速大漂角运动时所受到的非线性水动力。基于一种新的模糊滑模控制策略,为潜水器设计了鲁棒航向控制器。在不同的漂角子区间内分别设计局部镇定的滑模控制器,然后通过Takagi-Sugeno模糊推理系统将它们光滑连接,得到模糊滑模控制。仿真计算结果充分显示了该控制策略的有效性。     

应用两次展开法求解系泊柱体慢漂运动方程

在深海中系泊的海洋平台,如Spar平台,水下部分为带有系泊的圆柱结构,其水平方向运动响应往往具有较低的自振频率,容易在低频波浪力(源于非线性的差频效应)作用下发生共振响应,使结构发生大幅水平慢漂。当浮体的瞬时位置大幅偏离初始位置时,基于初始平衡位置的摄动展开法会存在较大误差。针对这一问题,采用两次展开方法,对大幅慢漂运动开展时域模拟研究。对双色波作用下自由漂浮圆柱的大幅运动响应问题进行数值分析,并与采用基于初始平衡位置的摄动展开法的计算结果进行了对比。结果表明,采用新的两次展开法可以计算出波浪遭遇频率的变化和波浪漂移阻尼,而这无法从基于初始平衡位置的常规摄动展开法中得到,体现了两次展开法在分析大幅慢漂问题上的优势。     

台风海况下半潜式钻井平台动力性能监测与分析

半潜式钻井平台在海洋油气资源开发中发挥着重要作用,目前主要采用模型试验和数值模拟方法对其动力性能进行研究,非常缺乏台风等极端海况下半潜式平台动力响应的实海域监测数据。以某半潜式钻井平台为研究对象,构建了一套比较完善的平台动力性能监测系统,并对台风“杜苏芮”过境阶段的监测数据进行了分析。根据平台艏部气隙及运动监测数据推算了平台吃水及环境波高;采用随机波浪的统计分析方法,计算得到短期海况的有效波高、谱峰周期、能量谱等信息,通过与多种典型海浪谱对比发现Jonswap谱与所测波谱吻合较好;对平台的横摇、纵摇及垂荡运动进行了时域统计分析和频域谱分析,得到了台风海况下被测平台波频运动的实际响应特征,对于指导平台抗台作业具有重要意义。     

波浪漂移力的数值模拟

本文首先利用基于多极展开的切片法成功地计算了在规则波中的定常漂移力,然后近似地求得在不规则波中的慢漂力。该方法可以用于初步设计中的仿真计算。     

海洋环境要素计算不确定性分析

以一艘现役起重船为研究对象,对其进行不同水深(46 m和36 m),缩尺比1∶50的模型试验。采用基于二次传递函数QTF的时域准静态分析法对实际尺度起重船与系泊系统进行耦合数值分析,并与试验结果进行比较。结果表明,当水深变浅时,浅水对二阶载荷的影响是系泊力明显的主要因素,浅水对一阶载荷的影响有限。在保持系泊系统刚度线性不随水深变化的前提下进行了三个水深吃水比的数值模拟计算,结果表明,对于系泊起重船,随着水深的减小,二阶定常力有所增大;浅水对差频载荷的影响在30 m水深(吃水水深比d/h=0.27)时变得明显。对于浅水系泊系统的相关分析需要充分考虑水深对二阶慢漂运动的影响,保证系泊系统的安全。     

Numerical analysis on ship maneuvering coupled with ship motion in waves

This paper considers a numerical analysis of ship maneuvering performance in the presence of incident waves and resultant ship motion responses. To this end, a time-domain ship motion program is developed to solve the wave–body interaction problem with the ship slip speed and rotation, and it is coupled with a modular-type 4-DOF maneuvering problem. In this coupled problem, the second-order mean drift force, which can play an important role in the ship maneuvering trajectory, is estimated by using a direct pressure integration method. The developed method is validated by observing the second-order mean drift force, and planar trajectories in maneuvering tests with and without the presence of incident waves. The comparisons are made for two ship models, Series 60 with block coefficient 0.7 and the S-175 containership, with existing experimental data. The maneuvering tests observed in this study include a zig-zag test in calm water, and turning tests in calm water and in regular waves. The present results show a fair agreement of overall tendency in maneuvering trajectories.     

海上浮体动力定位外力计算

动力定位系统（dynamic positioning system）是一种闭环自动控制系统,采用推力器来抵抗风、浪、流等作用在浮体上的境力,使其保持在所要求的位置上。船舶的风和流作用力由经验公式求得,波浪力主要考虑二阶漂移力,由三维势流理论的直接积分法求得。通过模拟仿真,表明其结果能够用于船舶动力定位系统研究。     

浮体二阶运动下钢悬链式立管触地区动态响应分析

浮体运动是引起钢悬链式立管(steel catenary riser,简称SCR)动态响应和疲劳损伤的关键因素,目前研究SCR问题时,为简化计算往往仅考虑平台一阶运动,忽略二阶运动影响。而实际上不同浮体结构的二阶运动响应特征明显,拟以SCR服役张力腿平台(tension leg platform,简称TLP)为例,探讨浮体二阶运动对SCR触地区动态响应的影响。建立考虑海床刚度退化的管土作用模型以改进现有的CABLE3D RSI程序,通过编写程序接口,将有限元分析得到的平台实际运动响应导入,研究平台不同运动作用下SCR触地区的位移、动力响应及疲劳分布情况。根据波流作用方向将TLP二阶慢漂运动分为近端和远端漂移两种工况,发现二阶运动下立管与海床的作用范围会增大,且触地区不仅发生高频小幅振荡运动,同时伴随低频大幅运动响应;平台远端漂移时,管内张力敏感程度高,而近端漂移时触地区的弯矩显著增大,都会不同程度提高触地区的疲劳损伤率。研究可为服役不同浮体的SCR响应预测与疲劳分析提供参考和借鉴。     

冰区四季通用灯浮标的二阶波浪力计算

冰区四季通用灯浮标是一种为满足北方冬季冰冻港口一年四季的助航服务需求研制的新型灯浮标,二阶波浪力对其漂浮姿态和漂移运动有较大影响。文中研究了浮标受到的二阶波浪力的数值计算方法,计算了不同流速下罐形和锥形灯浮标的二阶波浪力。研究结果显示,罐形和锥形灯浮标受到的一阶波浪力相差不大,罐形的二阶波浪力明显小于锥形,具有一定的外形优势。     

动力定位船舶伪逆法与混沌粒子群法相融合的推力分配算法研究

动力定位船舶一般都装备冗余推进器,推力分配求解将直接影响最终定位的效果。针对伪逆法在推力分配中存在问题,提出一种把伪逆法和混沌粒子群法(CPSO)相融合的推力分配算法,该组合算法方便处理推力器各种限制条件,计算简单,能兼顾船舶的能耗及操作性,解决奇点问题。最后以某挖泥船为例,仿真结果表明该推力分配算法具备一定的实用指导价值,能有效提高船舶的定位性能。     

Measures to diminish the parameter drift in the modeling of ship manoeuvring using system identification

System identification provides an effective way to predict the ship manoeuvrability. In this paper several measures are proposed to diminish the parameter drift in the parametric identification of ship manoeuvring models. The drift of linear hydrodynamic coefficients can be accounted for from the point of view of dynamic cancellation, while the drift of nonlinear hydrodynamic coefficients is explained from the point of view of regression analysis. To diminish the parameter drift, reconstruction of the samples and modification of the mathematical model of ship manoeuvring motion are carried out. Difference method and the method of additional excitation are proposed to reconstruct the samples. Using correlation analysis, the structure of a manoeuvring model is simplified. Combined with the measures proposed, support vector machines based identification is employed to determine the hydrodynamic coefficients in a modified Abkowitz model. Experimental data from the free-running model tests of a KVLCC2 ship are analyzed and the hydrodynamic coefficients are identified. Based on the regressive model, simulation of manoeuvres is conducted. Comparison between the simulation results and the experimental results demonstrates the validity of the proposed measures.     

Dynamic Analysis of Semi-Submersible Production Platform Under the Failure of Mooring Lines

This paper quantitatively studies the transient dynamic response of a semi-submersible production platform with the loss of one or several positioning mooring lines.A semi-submersible platform,production risers,and positioning mooring lines are all included in the numerical simulation.Increased motion of the semi-submersible platform,tension variation of the remaining mooring lines/risers and the risk of mooring line or riser clashing are all investigated through fully coupled time-domain analysis.Combined environmental loads are selected from irregular waves and the steady current varying from very rough to extreme sea conditions.Three dimension radiation/diffraction theories and Morison’s equation are applied to calculate first-order wave force and second-order mean drift force of floating semi-submersible platform.Nonlinear time-domain finite element methods are employed to analyze the behavior of mooring lines and risers.Results show that the failure of mooring lines seriously reduce the platform’s stability performance.The tension of the rest lines is also increased accordingly.Remaining lines which are closer to the failed lines will have larger tension increase to compensate.Line-Line distance provides practical information for the risk of clashing investigation.     

Portable dynamic positioning control system on a barge in short-crested waves using the neural network algorithm

This paper develops a nonlinear mathematical model to simulate the dynamic motion behavior of the barge equipped with the portable outboard Dynamic Positioning (DP) system in short-crested waves. The self-tuning Proportional-Derivative (PD) controller based on the neural network algorithm is applied to control the thrusters for optimal adjustment of the barge position in waves. In addition to the wave, the current, the wind and the nonlinear drift force are also considered in the calculations. The time domain simulations for the six-degree-of-freedom motions of the barge with the DP system are solved by the 4th order Runge-Kutta method which can compromise the efficiency and the accuracy of the simulations. The technique of the portable alternative DP system developed here can serve as a practical tool to assist those ships without being equipped with the DP facility while the dynamic positioning missions are needed.     

Feed-forward control for dynamic positioning in random waves based on quadratic impulse function and real-time wave measurement

The real-time estimation of second-order difference-frequency wave forces using real-time random-wave measurement is developed for the FF (feed-forward) control based dynamic positioning of floating offshore vessels and platforms. The efficacy of the developed FF control scheme is validated by using the in-house hull-mooring-riser-thruster fully coupled time-domain computer simulation program through comparisons with the results by the conventional feedback-control-only case. The feedback (FB) control intends to reduce the accumulated position-excursion error, meanwhile the proposed feed-forward control compensates the controllable slowly-varying wave loads by activating thrusters in advance based on the real-time estimation of the second-order difference-frequency wave loadings using the real-time signal of random incident wave. The real-time estimation of the second-order difference-frequency wave loads is done by using the double-convolution integral with pre-calculated QIF (quadratic impulse function). The numerical DP system is successfully implemented with the FF control algorithm in the vessel-thruster fully coupled time-domain simulation program. The developed schemes are applied to a turret-moored FPSO (floating production storage offloading) with six dynamic-positioning (DP) azimuth thrusters in two non-collinear storm conditions. It is clearly demonstrated that the developed FF control scheme performs much better than the conventional feedback-control-only case. The corresponding reductions in horizontal offsets, motions, mooring tensions, and fuel consumptions by using the developed FF control scheme are underscored.