<Emphasis Type="Italic">Q</Emphasis><Subscript>c</Subscript> and <Emphasis Type="Italic">Q</Emphasis><Subscript>S</Subscript> wave attenuation of South African earthquakes

Quality factor Q, which describes the attenuation of seismic waves with distance, was determined for South Africa using data recorded by the South African National Seismograph Network. Because of an objective paucity of seismicity in South Africa and modernisation of the seismograph network only in 2007, I carried out a coda wave decay analysis on only 13 tectonic earthquakes and 7 mine-related events for the magnitude range 3.6?≤?M _L ?≤?4.4. Up to five seismograph stations were utilised to determine Q _c for frequencies at 2, 4, 8 and 16 Hz resulting in 84 individual measurements. The constants Q ₀ and α were determined for the attenuation relation Q _c(f)?=?Q ₀ f ^α . The result was Q ₀?=?396?±?29 and α?=?0.72?±?0.04 for a lapse time of 1.9*(t _s???t ₀) (time from origin time t ₀ to the start of coda analysis window is 1.9 times the S-travel time, t _s) and a coda window length of 80 s. This lapse time and coda window length were found to fit the most individual frequencies for a signal-to-noise ratio of at least 3 and a minimum absolute correlation coefficient for the envelope of 0.5. For a positive correlation coefficient, the envelope amplitude increases with time and Q _c was not calculated. The derived Q _c was verified using the spectral ratio method on a smaller data set consisting of nine earthquakes and one mine-related event recorded by up to four seismograph stations. Since the spectral ratio method requires absolute amplitudes in its calculations, site response tests were performed to select four appropriate stations without soil amplification and/or signal distortion. The result obtained for Q _S was Q ₀?=?391?±?130 and α?=?0.60?±?0.16, which agrees well with the coda Q _c result.     

A new <Emphasis Type="Italic">M</Emphasis><Subscript><Emphasis Type="Italic">w</Emphasis></Subscript> estimation parameter for use in earthquake early warning systems

We propose a method that employs the squared displacement integral (ID2) to estimate earthquake magnitudes in real time for use in earthquake early warning (EEW) systems. Moreover, using τ _c and P _d for comparison, we establish formulas for estimating the moment magnitudes of these three parameters based on the selected aftershocks (4.0 ≤ M _s  ≤ 6.5) of the 2008 Wenchuan earthquake. In this comparison, the proposed ID2 method displays the highest accuracy. Furthermore, we investigate the applicability of the initial parameters to large earthquakes by estimating the magnitude of the Wenchuan M _s 8.0 mainshock using a 3-s time window. Although these three parameters all display problems with saturation, the proposed ID2 parameter is relatively accurate. The evolutionary estimation of ID2 as a function of the time window shows that the estimation equation established with ID2 ^Ref determined from the first 8-s of P wave data can be directly applicable to predicate the magnitudes of 8.0. Therefore, the proposed ID2 parameter provides a robust estimator of earthquake moment magnitudes and can be used for EEW purposes.     

Seismotectonic studies of the pleistoseist area of the <Emphasis Type="Italic">M</Emphasis> <Subscript> <Emphasis Type="Italic">s</Emphasis> </Subscript> = 6.9 Ilin-Tass earthquake in northeast Yakutia

The complex seismotectonic studies of the pleistoseist area of the Ilin-Tas earthquake (M_s = 6.9), one of the strongest seismic events ever recorded by the regional seismic network in northeastern Russia, are carried out. The structural tectonic position, morphotectonic features of present-day topography, active faults, and types of Cenozoic deformations of the epicentral zone are analyzed. The data of the instrumental observations are summarized, and the manifestations of the strong seismic events in the Yana–Indigirka segment of the Cherskii seismotectonic zone are considered. The explanation is suggested for the dynamical tectonic setting responsible for the Andrei-Tas seismic maximum. This setting is created by the influence of the Kolyma–Omolon indenter, which intrudes into the Cherskii seismotectonic zone from the region of the North American lithospheric plate and forms the main seismogenic structures of the Yana–Indigirka segment in the frontal zone (the Ilin-Tas anticlinorium). The highest seismic potential is noted in the Andrei- Tas block—the focus of the main tectonic impacts from the Kolyma–Omolon superterrane. The general trend of this block coincides with the orientation of the major axis of isoseismal ellipses (azimuth 50°–85°), which were determined from the observations of macroseismic effects on the ground after the Uyandina (M_s = 5.6), Andrei-Tas (M_s = 6.1), and Ilin-Tas (M_s = 6.9) earthquakes.     

The earthquake of July 22, 2011 (<Emphasis Type="Italic">M</Emphasis><Subscript><Emphasis Type="Italic">w</Emphasis></Subscript> = 4.5) in a low-seismicity area of the Argun region

The paper considers the Argun earthquake of July 22, 2011 (M _w = 4.5), which occurred in the Argun River valley in a low-seismicity territory in China. The focal parameters of the earthquake (depth of the hypocenter, moment magnitude, scalar seismic moment, and focal mechanism) were determined by calculating the seismic moment tensor from the amplitude spectra of surface waves and the data on the signs of the first arrivals of body waves at regional stations. The solution of the focal mechanism makes it possible to assume a relationship between the earthquake focus and a fault with a northeastern strike bordering the southeastern side of the Argun Basin (in Chinese territory). The Argun earthquake was felt in Russia with an intensity of II–III to V at the epicentral distances up to 255 km. The intensity of shaking did not exceed values suggested by new GSZ-2012 and GSZ-2014 seismic zoning maps of Russian territory. Nevertheless, the question on the possible occurrence of stronger earthquakes in the studied region remains open.     

A study of Guptkashi,Uttarakhand earthquake of 6 February 2017 (<Emphasis Type="Italic">M</Emphasis><Subscript><Emphasis Type="Italic">w</Emphasis></Subscript>5.3) in the Himalayan arc and implications for ground motion estimation

The 2017 Guptkashi earthquake occurred in a segment of the Himalayan arc with high potential for a strong earthquake in the near future. In this context, a careful analysis of the earthquake is important as it may shed light on source and ground motion characteristics during future earthquakes. Using the earthquake recording on a single broadband strong-motion seismograph installed at the epicenter, we estimate the earthquake’s location (30.546° N, 79.063° E), depth (H?=?19 km), the seismic moment (M₀?=?1.12×10¹⁷ Nm, M _w 5.3), the focal mechanism (φ?=?280°, δ?=?14°, λ?=?84°), the source radius (a?=?1.3 km), and the static stress drop (Δσ _s ~22 MPa). The event occurred just above the Main Himalayan Thrust. S-wave spectra of the earthquake at hard sites in the arc are well approximated (assuming ω^?2 source model) by attenuation parameters Q(f)?=?500f^0.9, κ?=?0.04 s, and f_max?=?infinite, and a stress drop of Δσ?=?70 MPa. Observed and computed peak ground motions, using stochastic method along with parameters inferred from spectral analysis, agree well with each other. These attenuation parameters are also reasonable for the observed spectra and/or peak ground motion parameters in the arc at distances ≤?200 km during five other earthquakes in the region (4.6?≤?M _w ?≤?6.9). The estimated stress drop of the six events ranges from 20 to 120 MPa. Our analysis suggests that attenuation parameters given above may be used for ground motion estimation at hard sites in the Himalayan arc via the stochastic method.     

<Emphasis Type="Italic">M</Emphasis>9 Tohoku Earthquake Hydro- and Seismic Response in the Caucasus and North Turkey

Presently, there are a lot of observations on the significant impact of strong remote earthquakes on underground water and local seismicity. Teleseismic wave trains of strong earthquakes give rise to several hydraulic effects in boreholes, namely permanent water level changes and water level oscillations, which closely mimic the seismograms (hydro-seismograms). Clear identical anomalies in the deep borehole water levels have been observed on a large part of the territory of Georgia during passing of the S and Love–Rayleigh teleseismic waves (including also multiple surface Rayleigh waves) of the 2011 Tohoku M9 earthquake. The analysis carried out in order to find dynamically triggered events (non-volcanic tremors) of the Tohoku earthquake by the accepted methodology has not revealed a clear tremor signature in the test area: the Caucasus and North Turkey. The possible mechanisms of some seismic signals of unknown origin observed during passage of teleseismic waves of Tohoku earthquake are discussed.     

3D <Emphasis Type="Italic">v</Emphasis><Subscript>P</Subscript> and <Emphasis Type="Italic">v</Emphasis><Subscript>S</Subscript> models of southeastern margin of the Tibetan plateau from joint inversion of body-wave arrival times and surface-wave dispersion data

A new 3D velocity model of the crust and upper mantle in the southeastern (SE) margin of the Tibetan plateau was obtained by joint inversion of body- and surface-wave data. For the body-wave data, we used 7190 events recorded by 102 stations in the SE margin of the Tibetan plateau. The surface-wave data consist of Rayleigh wave phase velocity dispersion curves obtained from ambient noise cross-correlation analysis recorded by a dense array in the SE margin of the Tibetan plateau. The joint inversion clearly improves the v _S model because it is constrained by both data types. The results show that at around 10 km depth there are two low-velocity anomalies embedded within three high-velocity bodies along the Longmenshan fault system. These high-velocity bodies correspond well with the Precambrian massifs, and the two located to the northeast of 2013 M _S 7.0 Lushan earthquake are associated with high fault slip areas during the 2008 Wenchuan earthquake. The aftershock gap between 2013 Lushan earthquake and 2008 Wenchuan earthquake is associated with low-velocity anomalies, which also acts as a barrier zone for ruptures of two earthquakes. Generally large earthquakes (M ≥ 5) in the region occurring from 2008 to 2015 are located around the high-velocity zones, indicating that they may act as asperities for these large earthquakes. Joint inversion results also clearly show that there exist low-velocity or weak zones in the mid-lower crust, which are not evenly distributed beneath the SE margin of Tibetan plateau.     

Attenuation coefficients of Rayleigh and <Emphasis Type="Italic">Lg</Emphasis> waves

Analysis of the frequency dependence of the attenuation coefficient leads to significant changes in interpretation of seismic attenuation data. Here, several published surface-wave attenuation studies are revisited from a uniform viewpoint of the temporal attenuation coefficient, denoted by χ. Theoretically, χ( f) is expected to be linear in frequency, with a generally non-zero intercept γ?=?χ(0) related to the variations of geometrical spreading, and slope dχ/df = π/Q _e caused by the effective attenuation of the medium. This phenomenological model allows a simple classification of χ( f) dependences as combinations of linear segments within several frequency bands. Such linear patterns are indeed observed for Rayleigh waves at 500–100-s and 100–10-s periods, and also for Lg from ~2 s to ~1.5 Hz. The Lg χ( f) branch overlaps with similar linear branches of body, Pn, and coda waves, which were described earlier and extend to ~100 Hz. For surface waves shorter than ~100 s, γ values recorded in areas of stable and active tectonics are separated by the levels of \(\gamma _{D} \approx 0.2 \times 10^{-3}\) s^???1 (for Rayleigh waves) and 8 ×10^???3 s^???1 (for Lg). The recently recognized discrepancy between the values of Q measured from long-period surface waves and normal-mode oscillations could also be explained by a slight positive bias in the geometrical spreading of surface waves. Similarly to the apparent χ, the corresponding linear variation with frequency is inferred for the intrinsic attenuation coefficient, χ _i , which combines the effects of geometrical spreading and dissipation within the medium. Frequency-dependent rheological or scattering Q is not required for explaining any of the attenuation observations considered in this study. The often-interpreted increase of Q with frequency may be apparent and caused by using the Q-based model of attenuation and following preferred Q( f) dependences while ignoring the true χ( f) trends within the individual frequency bands.     

Changes in source parameters of foreshocks and aftershocks of the 2001 <Emphasis Type="Italic">M</Emphasis><Subscript>S</Subscript>=6.0 Yajiang,Sichuan, earthquake

In this paper changes in focal mechanisms, parameters of wave spectra, and stress drops for the M _S=5.0 foreshock and M _S=6.0 mainshock in February 2001 in Yajiang County, Sichuan, and seismicity in epicentral region are studied. Comparison of focal mechanisms for the Yajiang earthquakes with distribution patterns of aftershocks, the nodal plane I, striking in the direction of NEN, of the Yajiang M=5.0 event is chosen as the faulting plane; the nodal plane II, striking in the direction of WNW, of the M=6.0 event as the faulting plane. The strikes of the two faulting planes are nearly perpendicular to each other. The level of stress drops in the epicentral region before the occurrence of the M=6.0 earthquake increases, which is consistent with increase of seismicity in the epicentral region. The rate decay of the Yajiang earthquake sequence, changes in wave spectra for foreshocks and aftershocks, and focal mechanisms are complex.     

Sampling uncertainties and source <Emphasis Type="Italic">b</Emphasis> likelihood for the Gutenberg-Richter <Emphasis Type="Italic">b</Emphasis> value from the Aki-Utsu method

The Aki-Utsu method of Gutenberg-Richter (G-R) b value estimation is often misapplied so that estimations not using the G-R histogram are often meaningless because they are not based on adequate samples. We propose a method to estimate the likelihood Pr(b?b _m , N, M ₁, M ₂) that an observed b _m estimate, based on a sample of N magnitudes within an [M ₁????≤?ΔM/2,?M ₂?+?ΔM/2) range, where ΔM?=?0.1 is the usual rounding applied to magnitudes, is due to a “true” source b value, b, and use these likelihoods to estimate source b ranges corresponding to various confidence levels. As an example of application of the method, we estimate the b values before and after the occurrence of a 7.4-magnitude earthquake in the Mexican subduction zone, and find a difference of 0.82 between them with 100% confidence that the b values are different.     

Dependence of geomagnetic disturbances on extreme values of the solar wind <Emphasis Type="Italic">E</Emphasis><Subscript><Emphasis Type="Italic">y</Emphasis></Subscript> component

The dependence of the zonal geomagnetic indices (AE, Ap, Kp, Kn, and Dst) on the solar wind parameters (the electric field E _y component, dynamic pressure P _d and IMF irregularity σB) has been studied for two types of events: magnetic clouds and high-speed streams. Based on the empirical relationships, it has been established that the AE, Ap, Kp, and Kn indices are directly proportional to the E _y value at E _y < 12 mV m^?1 and are inversely proportional to this value at E _y > 12 mV m^?1 for the first-type events. On the contrary, the dependence of Dst on E _y is monotonous nonlinear. A linear dependence of all geomagnetic indices on E _y is typical of the second-type events. It has been indicated that the specific features of geoeffectiveness of magnetic clouds and high-speed solar wind streams are caused by the dependence of the electric field potential across the polar cap on the electric field, solar wind dynamic pressure, and IMF fluctuations.     

Mechanism of formation of <Emphasis Type="Italic">Q</Emphasis>-disturbances in the <Emphasis Type="Italic">F</Emphasis><Subscript>2</Subscript> region of the equatorial ionosphere

Using model simulations, the morphological picture (revealed earlier) of the disturbances in the F ₂ region of the equatorial ionosphere under quiet geomagnetic conditions (Q-disturbances) is interpreted. It is shown that the observed variations in the velocity of the vertical E × B plasma drift, related to the zonal E _y component of the electric field, are responsible for the formation of Q-disturbances. The plasma recombination at altitudes of the lower part of the F ₂ region and the dependence of the rate of this process on heliogeophysical conditions compose the mechanism of Q-disturbance formation at night. The daytime positive Q-disturbances are caused exclusively by a decrease in the upward E × B drift, and this type of disturbances could be related to the known phenomenon of counter electrojet. Possible causes of formation of the daytime negative Q-disturbances are discussed.     

Seismicity anomalies before the great earthquake of <Emphasis Type="Italic">M</Emphasis><Subscript>S</Subscript>=8.1 in the Kunlun Pass and its significance to earthquake prediction

A great earthquake of M _S=8.1 took place in the west of Kunlun Pass on November 14, 2001. The epicenter is located at 36.2°N and 90.9°E. The analysis shows that some main precursory seismic patterns appear before the great earthquake, e.g., seismic gap, seismic band, increased activity, seismicity quiet and swarm activity. The evolution of the seismic patterns before the earthquake of M _S=8.1 exhibits a course very similar to that found for earthquake cases with M _S≥7. The difference is that anomalous seismicity before the earthquake of M _S=8.1 involves in the larger area coverage and higher seismic magnitude. This provides an evidence for recognizing precursor and forecasting of very large earthquake. Finally, we review the rough prediction of the great earthquake and discuss some problems related to the prediction of great earthquakes.     

Studying the spread <Emphasis Type="Italic">F</Emphasis> effect before earthquakes

The observations of spread F during the nighttime hours (0000–0500 LT) have been statistically analyzed based on data of Tokyo, Akita, Wakkanai, and Yamagawa Japan vertical ionospheric sounding stations for the time intervals a month before and a month after an earthquake. The disturbances in the probability of spread F appearance before an earthquake are revealed against a background of the variations depending on season, solar activity cycle, geomagnetic and solar disturbances. The days with increased solar (Wolf number W > 100) and geomagnetic (ΣK > 30) activity are excluded from the analysis. The spread F effects are considered for more than a hundred earthquakes with magnitude M > 5 and epicenter depth h < 80 km at distances of R < 1000 km from epicenters to the vertical sounding station. An average decrease in the spread F occurrence probability one-two weeks before an earthquake has been revealed using the superposed epoch method (the probability was minimal approximately ten days before the event and then increased until the earthquake onset). Similar results are obtained for all four stations. The reliability of the effect has been estimated. The dependence of the detected effect on the magnitude and distance has been studied.     

Variation of <Emphasis Type="Italic">Q</Emphasis> value before and after the 1999 Xiuyan,Liaoning Province, <Emphasis Type="Italic">M</Emphasis>=5.4 earthquake on the basis of analysis on attenuation dispersion of P waves

A method for determining medium quality factor is developed on the basis of analyzing the attenuation dispersion of the arrived first period P wave. In order to enhance signal to noise ratio, improve the resolution in measurement and reduce systematic error we applied the data resampling technique. The group velocity delay of P wave was derived by using an improved multi-filtering method. Based on a linear viscoelastic relaxation model we deduced the medium quality factor Q _m, and associated error with 95% confidence level. Applying the method to the seismic record of the Xiuyan M=5.4 earthquake sequences we obtained the following result: (1) High Q _m started to appear from Nov. 9, 1999. The events giving the deduced high Q _m value clustered in a region with their epicenter distances being between 32 and 46 km to the Yingkou station. This Q _m versus distance observation obviously deviates from the normal trend of Q _m linearly increasing with distance. (2) The average Q _m before the 29 Dec. 1999 M=5.4 earthquake is 460, while the average Q _m between the M=5.4 event and the 12 Jan. 2000 M=5.1 earthquake is 391, and the average Q _m after the M=5.1 event is 204.     

A real <Emphasis Type="Italic">P</Emphasis>-wave and its dependence on the presence of gas

Attenuation of seismic compression waves leads to the real existence of a fast P₁ wave in rocks which are fully saturated with dropping fluid and a slow P₂ wave in the rocks containing gas in their pores. This accounts for the seismic blanking zones below the gas horizons for the P₁ waves. Oscillations of gaseous inclusions ensure the energy transfer to the dominant frequencies which are different for the cases of passive seismic (few Hz) and active source seismic (10–20 Hz). The intervals of dominant frequencies are determined from the negative attenuation of these low-frequency waves. According to the observations and the suggested equation, random noise amplifies the signal at these frequencies. Thus, the P₂ waves at the dominant frequency of the active source seismics are applicable for elaborating on the details of the saturation of the production layer by hydrocarbons. The relation to the AVO method (Amplitude Variation with Offset) and dilatancy effect during the preparation of an earthquake is noted.     

Experimental examination on the heterogeneity parameter <Emphasis Type="Italic">C</Emphasis><Subscript>v</Subscript> of earthquake precursors

Two rock samples with different structures and materials were deformed under a biaxial loading system, and multipoint strain measurements were performed for each sample. The distribution of strain anomalies during the deformation and the instability process were analyzed by using C _v value put forward by WANG Xiao-qing and CHEN Xue-zhong, et al, a parameter to describe the heterogeneous distribution of earthquake precursors, so as to examine the method of C _v value and to explore its physical meaning experimentally. The result shows that the change of C _v value is correlated to the change of deformation characteristics and is an effective parameter to describe the heterogeneity of precursor distribution. C _v value increases firstly and then decreases before the instability, and the instability occurs when C _v value decreases to the level before increasing. This indicates that C _v value may be a useful parameter for earthquake prediction.     

The <Emphasis Type="Italic">Q</Emphasis>-factor estimates for the crust and upper mantle in the vicinity of Sochi and Anapa (North Caucasus)

The regularities in the radiation and propagation of seismic waves in the regions of the North Caucasus are analyzed for estimating the ground motion parameters during the probable future strong earthquakes. Based on the records of the regional earthquakes with magnitudes M_W ~ 3.9–5.6 within epicentral distances up to ~300 km obtained during the period of digital measurements at the Sochi and Anapa seismic stations, the Q-factors in the vicinities of these sites are estimated at ~55 f^0.9 and ~90f^0.7, respectively. The estimates were obtained by the coda normalization method developed by Aki, Rautian, and other authors. This method is based on the phenomenon of suppression of the earthquake (source) effects and local (site) responses by coda waves in the S-wave spectra. The obtained Q-factor estimates can be used for forecasting the ground shaking parameters for the future probable strong earthquakes in the North Caucasus in the vicinities of Sochi and Anapa.     

Magnitude <Emphasis Type="Italic">M</Emphasis><Subscript>w</Subscript> in metropolitan France

The recent seismicity catalogue of metropolitan France Sismicité Instrumentale de l’Hexagone (SI-Hex) covers the period 1962–2009. It is the outcome of a multipartner project conducted between 2010 and 2013. In this catalogue, moment magnitudes (M _w) are mainly determined from short-period velocimetric records, the same records as those used by the Laboratoire de Détection Géophysique (LDG) for issuing local magnitudes (M _L) since 1962. Two distinct procedures are used, whether M _L-LDG is larger or smaller than 4. For M _L-LDG >4, M _w is computed by fitting the coda-wave amplitude on the raw records. Station corrections and regional properties of coda-wave attenuation are taken into account in the computations. For M _L-LDG ≤4, M _w is converted from M _L-LDG through linear regression rules. In the smallest magnitude range M _L-LDG <3.1, special attention is paid to the non-unity slope of the relation between the local magnitudes and M _w. All M _w determined during the SI-Hex project is calibrated according to reference M _w of recent events. As for some small events, no M _L-LDG has been determined; local magnitudes issued by other French networks or LDG duration magnitude (M _D) are first converted into M _L-LDG before applying the conversion rules. This paper shows how the different sources of information and the different magnitude ranges are combined in order to determine an unbiased set of M _w for the whole 38,027 events of the catalogue.     

Estimating seismic moments and Lg <Emphasis Type="Italic">Q</Emphasis> using Lg spectra

A multi-event and multi-station inverse method is presented in the paper to simultaneously estimate the seismic moments (M ₀) and source corner frequencies (f _c) of several Jiashi (Xinjiang, China) earthquakes, as well as the apparent Lg Q models for the paths from Jiashi to eight seismic stations (WMQ, AAK, TLG, MAKZ, KUR, VOS, ZRN and CHK) in Central Asia. The resultant seismic moments correlate well with the M ₀ values obtained by Harvard University using the centroid moment tensor (CMT) inversion and the surface-wave magnitudes as well. After the correction by a typical value of average radiation coefficient for regional SV waves, the M ₀ values from Lg spectral inversion are still close to the corresponding values obtained from CMT inversion. The obtained apparent Q _0Lg values (Lg Q at 1 Hz) are consistent with the tectonic features of corresponding propagation paths. The Q _0Lg values are 351±87, 349±86 and 300±27 for the paths from Jiashi to AAK, TLG and MAKZ, respectively. They are smaller than Q _0Lg values for the paths to KUR, VOS, ZRN and CHK, which are 553±72, 569±58, 550±57 and 603±65, respectively. These results agree with the condition that the paths to AAK, TLG and MAKZ mainly propagate through the mountainous Tianshan area where relatively strong seismic activities and large variations of topography are exhibited, while the paths to KUR, VOS, ZRN and CHK mainly propagate through the stable area of Kazak platform. The Q _0Lg value for the path to WMQ is 462±56. This is also in agreement with the condition that the path to WMQ is basically along the border area between Tianshan Mountain and Tarim Basin, and along this path the variations of topography and crustal thickness are moderate in comparison with that along the path to MAKZ.