Permanganate oxidation of arsenic(III): Reaction stoichiometry and the characterization of solid product

Permanganate (MnO₄⁻) has widely been used as an effective oxidant for drinking water treatment systems, as well as for in situ treatment of groundwater impacted by various organic contaminants. The reaction stoichiometry of As(III) oxidation by permanganate has been assumed to be 1.5, based on the formation of solid product, which is putatively considered to be MnO₂(s). This study determined the stoichiometric ratio (SR) of the oxidation reaction with varying doses of As(III) (3-300 μM) and MnO₄⁻ (0.5 or 300 μM) under circumneutral pH conditions (pH 4.5-7.5). We also characterized the solid product that was recovered ∼1 min after the oxidation of 2.16 mM As(III) by 0.97 mM MnO₄⁻ at pH 6.9 and examined the feasibility of secondary heterogeneous As(III) oxidation by the solid product. When permanganate was in excess of As(III), the SR of As(III) to Mn(VII) was 2.07 ± 0.07, regardless of the solution pH; however, it increased to 2.49 ± 0.09 when As(III) was in excess. The solid product was analogous to vernadite, a poorly crystalline manganese oxide based on XRD analysis. The average valence of structural Mn in the solid product corresponded to +III according to the splitting interval of the Mn3s peaks (5.5 eV), determined using X-ray photoelectron spectroscopy (XPS). The relative proportions of the structural Mn(IV):Mn(III):Mn(II) were quantified as 19:62:19 by fitting the Mn2p_3/2 spectrum of the solid with the five multiplet binding energy spectra for each Mn valence. Additionally, the O1s spectrum of the solid was comparable to that of Mn-oxide but not of Mn-hydroxide. These results suggest that the solid product resembled a poorly crystalline hydrous Mn-oxide such as (Mn^II_0.19Mn^III_0.62Mn^IV_0.19)₂O₃·nH₂O, in which Mn(II) and Mn(IV) were presumably produced from the disproportionation of aqueous phase Mn(III). Thermodynamic calculations also show that the formation of Mn(III) oxide is more favorable than that of Mn(IV) oxide from As(III) oxidation by permanganate under circumneutral pH conditions. Arsenic(III), when it remained in the solution after all of the permanganate was consumed, was effectively oxidized by the solid product. This secondary heterogeneous As(III) oxidation consisted of three steps: sorption to and oxidation on the solid surface and desorption of As(V) into solution, with the first step being the rate-limiting process as observed in As(III) oxidation by various Mn (oxyhydr)oxides reported elsewhere. We also discussed a potential reaction pathway of the permanganate oxidation of As(III).     

Mechanism of enrichment of trace metals on fine sludges collected from filtration plants

Fine sludges were collected from five filtration plants, and the partitioning of ten metals (Ag, Cd, Mn, Zn, Pb, Cu, Sn, Co, Ni, and Fe) in them was determined by selective leaching techniques. (1) The available amounts, which shows the total of each metal leached between 1 M CH₃COONH₄ and 30 percent H₂O₂, for Ag, Cd and Mn, ranged from 51 to 98 percent for five sludges. (2) The available amounts for Zn, Pb, Cu, and Sn were 47–92 percent for five sludges. (3) The most important fraction for Co, Ni, and Fe, except the Inagawa sludge, which is markedly polluted by organic matter, was the crystalline particle. Therefore, the above metals, except Co, Ni, and Fe, are thought to be enriched on ion-exchangeable sites, organic matter, hydrous Fe/Mn oxides, and sulfides in fine sludges.     

Field application of calcite Dispersed Alkaline Substrate (calcite-DAS) for passive treatment of acid mine drainage with high Al and metal concentrations

Passive treatment systems are widely used for remediation of acid mine drainage (AMD), but existing designs are prone to clogging or loss of reactivity due to Al- and Fe-precipitates when treating water with high Al and heavy metal concentrations. Dispersed alkaline substrate (DAS) mixed from a fine-grained alkaline reagent (e.g. calcite sand) and a coarse inert matrix (e.g. wood chips) had shown high reactivity and good hydraulic properties in previous laboratory column tests. In the present study, DAS was tested at pilot field scale in the Iberian Pyrite Belt (SW Spain) on metal mine drainage with pH near 3.3, net acidity 1400–1650 mg/L as CaCO₃, and mean concentrations of 317 mg/L Fe (95% Fe(II)), 311 mg/L Zn, 74 mg/L Al, 20 mg/L Mn, and 1.5–0.1 mg/L Cu, Co, Ni, Cd, As and Pb. The DAS-tank removed an average of 870 mg/L net acidity as CaCO₃ (56% of inflow), 25% Fe, 93% Al, 5% Zn, 95% Cu, 99% As, 98% Pb, and 14% Cd, but no Mn, Ni or Co. Average gross drain pipe alkalinity was 181 mg/L as CaCO₃, which increased total Fe removal to 153 mg/L (48%) in subsequent sedimentation ponds. Unfortunately, the tank suffered clogging problems due to the formation of a hardpan of Al-rich precipitates. DAS lifetime could probably be increased by lowering Al-loads.     

Arsenite sorption at the magnetite-water interface during aqueous precipitation of magnetite: EXAFS evidence for a new arsenite surface complex

The interaction of aqueous As(III) with magnetite during its precipitation from aqueous solution at neutral pH has been studied as a function of initial As/Fe ratio. Arsenite is sequestered via surface adsorption and surface precipitation reactions, which in turn influence the crystal growth of magnetite. Sorption samples were characterized using EXAFS spectroscopy at the As K-edge in combination with HRTEM observations, energy dispersive X-ray analysis at the nanoscale, electron energy loss spectroscopy at the Fe L₃-edge, and XRD-Rietveld analyses of reaction products. Our results show that As(III) forms predominantly tridentate hexanuclear As(III)O₃ complexes (³C), where the As(III)O₃ pyramids occupy vacant tetrahedral sites on {1 1 1} surfaces of magnetite particles. This is the first time such a tridentate surface complex has been observed for arsenic. This complex, with a dominant As-Fe distance of 3.53 ± 0.02 Å, occurs in all samples examined except the one with the highest As/Fe ratio (0.33). In addition, at the two highest As/Fe ratios (0.133 and 0.333) arsenite tends to form mononuclear edge-sharing As(III)O₃ species (²E) within a highly soluble amorphous As(III)-Fe(III,II)-containing precipitate. At the two lowest As/Fe ratios (0.007 and 0.033), our results indicate the presence of additional As(III) species with a dominant As-Fe distance of 3.30 ± 0.02 Å, for which a possible structural model is proposed. The tridentate ³C As(III)O₃ complexes on the {1 1 1} magnetite surface, together with this additional As(III) species, dramatically lower the solubility of arsenite in the anoxic model systems studied. They may thus play an important role in lowering arsenite solubility in putative magnetite-based water treatment processes, as well as in natural iron-rich anoxic media, especially during the reductive dissolution-precipitation of iron minerals in anoxic environments.     

Kinetics of biotite dissolution and Fe behavior under low O2 conditions and their implications for Precambrian weathering

Biotite dissolution experiments were carried out to better understand the dissolution kinetics and Fe behavior under low O₂ conditions, and to give an insight into the Precambrian weathering. Mineral dissolution with a continuous flow-through reactor was employed at 25 °C for up to 65 days varying partial pressure of atmospheric oxygen (PO₂), pH (6.86 and 3.01) and Fe content in mineral (1.06 and 0.11 mol of Fe per O₁₀(OH,F)₂ for biotite and phlogopite, respectively) independently for the examination of their effects on biotite dissolution. Low PO₂ conditions were achieved in a newly developed glove box (PO₂ ? 6 × 10⁻⁴ atm; referred to as anoxic conditions), which was compared to the present, ambient air conditions (0.2 atm of PO₂; oxic conditions). The biotite dissolution rate was slightly faster under anoxic conditions at pH 6.86 while it was not affected by PO₂ at pH 3.01. There was no direct effect of Fe content on dissolution rate at pH 6.86 while there was a small difference in dissolution rate between biotite and phlogopite at pH 3.01. The 1.5 order-of-magnitude faster release rate of Fe under anoxic conditions for biotite dissolution at pH 6.86 resulted from the difference in ratio of Fe³⁺ precipitates remaining in the reactor to Fe dissolved (about 60% and 100% under anoxic and oxic conditions, respectively), which is caused mainly by the difference in PO₂. The results infer that the Fe²⁺ and Fe³⁺ contents in the Paleoproterozoic paleosols, fossil weathering profiles, are reflected by atmospheric oxygen levels at the time of weathering.     

Geochemistry of highly acidic mine water following disposal into a natural lake with carbonate bedrock

Acid mine drainage (AMD) from the Zn–Pb(–Ag–Bi–Cu) deposit of Cerro de Pasco (Central Peru) and waste water from a Cu-extraction plant has been discharged since 1981 into Lake Yanamate, a natural lake with carbonate bedrock. The lake has developed a highly acidic pH of ∼1. Mean lake water chemistry was characterized by 16,775 mg/L acidity as CaCO₃, 4330 mg/L Fe and 29,250 mg/L SO₄. Mean trace element concentrations were 86.8 mg/L Cu, 493 mg/L Zn, 2.9 mg/L Pb and 48 mg/L As, which did not differ greatly from the discharged AMD. Most elements showed increasing concentrations from the surface to the lake bottom at a maximal depth of 41 m (e.g. from 3581 to 5433 mg/L Fe and 25,609 to 35,959 mg/L SO₄). The variations in the H and O isotope compositions and the element concentrations within the upper 10 m of the water column suggest mixing with recently discharged AMD, shallow groundwater and precipitation waters. Below 15 m a stagnant zone had developed. Gypsum (saturation index, SI ∼ 0.25) and anglesite (SI ∼ 0.1) were in equilibrium with lake water. Jarosite was oversaturated (SI ∼ 1.7) in the upper part of the water column, resulting in downward settling and re-dissolution in the lower part of the water column (SI ∼ −0.7). Accordingly, jarosite was only found in sediments from less than 7 m water depth. At the lake bottom, a layer of gel-like material (∼90 wt.% water) of pH ∼1 with a total organic C content of up to 4.40 wet wt.% originated from the kerosene discharge of the Cu-extraction plant and had contaminant element concentrations similar to the lake water. Below the organic layer followed a layer of gypsum with pH 1.5, which overlaid the dissolving carbonate sediments of pH 5.3–7. In these two layers the contaminant elements were enriched compared to lake water in the sequence As < Pb ≈ Cu < Cd < Zn = Mn with increasing depth. This sequence of enrichment was explained by the following processes: (i) adsorption of As on Fe-hydroxides coating plant roots at low pH (up to 3326 mg/kg As), (ii) adsorption at increasing pH near the gypsum/calcite boundary (up to 1812 mg/kg Pb, 2531 mg/kg Cu, and 36 mg/kg Cd), and (iii) precipitation of carbonates (up to 5177 mg/kg Zn and 810 mg/kg Mn; all data corrected to a wet base). The infiltration rate was approximately equal to the discharge rate, thus gypsum and hydroxide precipitation had not resulted in complete clogging of the lake bedrocks.     

Organic carbon amendments for passive in situ treatment of mine drainage: Field experiments

A field-scale experiment was conducted to evaluate various organic C sources as amendments for passive treatment of tailings pore water. Varied mixtures of peat, spent-brewing grain (SBG) and municipal biosolids (MB) were assessed for the potential to promote dissimilatory sulfate reduction (DSR) and metal-sulfide precipitation. Five amended cells and one control were constructed in the vadose zone of a sulfide- and carbonate-rich tailings deposit, and the geochemistry, microbiology and mineralogy were monitored for 4 a. Increases in pore-water concentrations of dissolved organic C (DOC) and decreases in aqueous SO₄ concentrations of >2500 mg L⁻¹ were observed in cells amended with peat + SBG and peat + SBG + MB. Removal of SO₄ was accompanied by shifts in δ³⁴S-SO₄ values of >+30‰, undersaturation of pore water with respect to gypsum [CaSO₄·2H₂O], and increased populations of SO₄-reducing bacteria (SRB). Decreases in aqueous concentrations of Zn, Mn, Ni, Sb and Tl were observed for these cells relative to the control. Organic C introduction also supported growth of Fe-reducing bacteria (IRB) and increases in Fe and As concentrations. Enhanced Fe and As mobility occurred in all cells; however, maximum concentrations were observed in cells amended with MB. Subsequent decreases in Fe and As concentrations were attributed to DSR and metal-sulfide precipitation. The common presence of secondary Zn-S and Fe-S phases was observed by field emission-scanning electron microscopy (FE-SEM) and energy dispersive X-ray (EDS) spectroscopy. Selective extractions indicated that large decreases in water-soluble SO₄ occurred in cells that supported DSR. Furthermore, amendments that supported DSR generally were characterized by slight decreases in solid-phase concentrations of extractable metal(loid)s. Amendment of tailings with organic C amendments that supported ongoing DOC production and DSR was essential for sustained treatment.     

Hydrogeochemical patterns,processes and mass transfers during aquifer storage and recovery (ASR) in an anoxic sandy aquifer

The hydrogeochemical processes that took place during an aquifer storage and recovery (ASR) trial in a confined anoxic sandy aquifer (Herten, the Netherlands) were identified and quantified, using observation wells at 0.1, 8 and 25 m distance from the ASR well. Oxic drinking water was injected in 14 ASR cycles in the period 2000–2009. The main reactions consisted of the oxidation of pyrite, sedimentary organic matter, and (adsorbed) Fe(II) and Mn(II) in all aquifer layers (A–D), whereas the dissolution of carbonates (Mg-calcite and Mn-siderite) occurred mainly in aquifer layer D. Extinction of the mobilization of SO₄, Fe(II), Mn(II), As, Co, Ni, Ca and total inorganic C pointed at pyrite and calcite leaching in layer A, whereas reactions with Mn-siderite in layer D did not show a significant extinction over time. Iron(II) and Mn(II) removal during recovery was demonstrated by particle tracking and pointed at sorption to neoformed ferrihydrite. Part of the oxidants was removed by neoformed organic material in the ASR proximal zone (0 – ca. 5 m) where micro-organisms grow during injection and die away when storage exceeds about 1 month. Anoxic conditions during storage led to increased concentrations for a.o. Fe(II), Mn(II) and NH₄ as noted for the first 50–200 m³ of abstracted water during the recovery phase. With a mass balance approach the water–sediment reactions and leaching rate of the reactive solid phases were quantified. Leaching of pyrite and calcite reached completion at up to 8 m distance in layer A, but not in layer D. The mass balance approach moreover showed that Mn-siderite in layer D was probably responsible for the Mn(II) exceedances of the drinking water standard (0.9 μmol/L) in the recovered water. Leaching of the Mn-siderite up to 8 m from the ASR well would take 1600 more pore volumes of drinking water injection (on top of the realized 460).     

Field multi-step limestone and MgO passive system to treat acid mine drainage with high metal concentrations

Passive treatment systems have become one of the most sustainable and feasible ways of remediating acid mine drainage (AMD). However, conventional treatments show early clogging of the porosity or/and coating of the reactive grains when high acidity and metal concentrations are treated. The performance of fine-grained reagents dispersed in a high porosity matrix of wood shavings was tested as an alternative to overcome these durability problems. The system consisted of two tanks of 3 m³ filled with limestone sand and wood shavings, and one tank of 1 m³ with caustic magnesia powder and wood shavings, separated by several oxidation cascades and decantation ponds. The system treated about 1.5 m³/day of AMD containing an average of 360 mg/L Fe, 120 mg/L Al, 390 mg/L Zn, 10 mg/L Cu, 300 μg/L As and 140 μg/L Pb, a mean pH of 3.08 and a net acidity of 2500 mg/L as CaCO₃ equivalent. The water reached pH 5 and 6 in the first and second limestone tanks, respectively (suitable to remove trivalent metals); and pH 8–9 in the MgO tank (suitable to remove divalent metals). After 9 months of operation, the system achieved an average removal of 100% Al, Cu, As, Pb, more than 70% Fe, about 25% Zn and 80% acidity. Goethite, schwertmannite, hydrobasaluminite, amorphous Al(OH)₃ and gypsum were the main precipitates in the two limestone tanks. Precipitation of divalent metals (Fe (II), Zn, and traces of Cd, Ni and Co) were complete inside the third tank of MgO, but preferential flow along the walls was responsible for its low treatment performance. Goethite, gypsum, Zn-schulenbergite and sauconite are the crystalline solid phases identified in the MgO tank.     

Comparison of arsenic geochemical evolution in the Datong Basin (Shanxi) and Hetao Basin (Inner Mongolia), China

Insightful knowledge of geochemical processes controlling As mobility is fundamental to understanding the occurrence of elevated As in groundwater. A comparative study of As geochemistry was conducted in the Datong Basin (Shanxi) and Hetao Basin (Inner Mongolia), two strongly As-enriched areas in China. The results show that As concentrations ranged from <1–1160 μg L⁻¹ (n = 37) in the Datong Basin and <1–804 μg L⁻¹ (n = 62) in the Hetao Basin. The groundwater is of the Na-HCO₃ type in the Datong Basin and Na-Cl-HCO₃ type in the Hetao Basin. Silicate mineral weathering and cation exchange processes dominated the groundwater geochemistry in the two study areas. Principal component analysis of 99 groundwater samples using 12 geochemical parameters indicated positive correlations between concentrations of As and Fe/Mn in the Datong Basin, but no correlation of As and Fe/Mn in the Hetao Basin. Phosphate correlated well with As in the Datong Basin and Hetao Basin, suggesting phosphate competition might be another process affecting As concentrations in groundwater. High concentrations of As, Fe, and Mn occurred in the pe range −2 to −4. The results of this study further understanding of the similarities and differences of As occurrence and mobility at various locations in China.     

Palaeo-hydrogeological control on groundwater As levels in Red River delta,Vietnam

To study the geological control on groundwater As concentrations in Red River delta, depth-specific groundwater sampling and geophysical logging in 11 monitoring wells was conducted along a 45 km transect across the southern and central part of the delta, and the literature on the Red River delta’s Quaternary geological development was reviewed. The water samples (n = 30) were analyzed for As, major ions, Fe²⁺, H₂S, NH₄, CH₄, δ¹⁸O and δD, and the geophysical log suite included natural gamma-ray, formation and fluid electrical conductivity. The SW part of the transect intersects deposits of grey estuarine clays and deltaic sands in a 15–20 km wide and 50–60 m deep Holocene incised valley. The NE part of the transect consists of 60–120 m of Pleistocene yellowish alluvial deposits underneath 10–30 m of estuarine clay overlain by a 10–20 m veneer of Holocene sediments. The distribution of δ¹⁸O-values (range −12.2‰ to −6.3‰) and hydraulic head in the sample wells indicate that the estuarine clay units divide the flow system into an upper Holocene aquifer and a lower Pleistocene aquifer. The groundwater samples were all anoxic, and contained Fe²⁺ (0.03–2.0 mM), Mn (0.7–320 μM), SO₄ (<2.1 μM–0.75 mM), H₂S (<0.1–7.0 μM), NH₄ (0.03–4.4 mM), and CH₄ (0.08–14.5 mM). Generally, higher concentrations of NH₄ and CH₄ and low concentrations of SO₄ were found in the SW part of the transect, dominated by Holocene deposits, while the opposite was the case for the NE part of the transect. The distribution of the groundwater As concentration (<0.013–11.7 μM; median 0.12 μM (9 μg/L)) is related to the distribution of NH₄, CH₄ and SO₄. Low concentrations of As (?0.32 μM) were found in the Pleistocene aquifer, while the highest As concentrations were found in the Holocene aquifer. PHREEQC-2 speciation calculations indicated that Fe²⁺ and H₂S concentrations are controlled by equilibrium for disordered mackinawite and precipitation of siderite. An elevated groundwater salinity (Cl range 0.19–65.1 mM) was observed in both aquifers, and dominated in the deep aquifer. A negative correlation between aqueous As and an estimate of reduced SO₄ was observed, indicating that Fe sulphide precipitation poses a secondary control on the groundwater As concentration.     

Temporal trends of dissolved weathering products released from a high Arctic coal mine waste rock pile in Svalbard (78°N)

It is well known that oxidation of sulphide-containing coal mine waste has considerable environmental impacts due to generation of acid mine drainage (AMD) containing high dissolved metal concentrations. This study is the first to evaluate seasonal trends in the release of AMD from high arctic coal mine waste rock. Runoff from an abandoned coal mine waste pile in Svalbard (78°N) was studied during the entire 3–4 month period with running water in 2005. Temporal variation in concentrations and fluxes of dissolved elements were quantified based on daily water sampling and used to evaluate weathering processes and estimate element budgets on a daily, seasonal and annual basis. Apart from alkali- and alkaline earth metals; Fe, Al, Mn, Zn and Ni were found to be the most abundant metals in the runoff. Element concentrations were highly correlated and suggest that the processes of sulphide oxidation, ion exchange and silicate weathering occurring within the waste pile were linked throughout the measuring period. Observed pH values varied from 2.8 to 5.2 and SO₄ concentrations from 21 to 1463 mg L⁻¹. Manganese and Al concentrations were observed above phytotoxic levels (up to 4 and 23 mg L⁻¹, respectively) and were considered the most critical elements in terms of environmental impact. Throughout the summer a total dissolved quantity of 58 kg Mn, 238 kg Al and 13,700 kg SO₄ was released from the pile containing approximately 200,000 m³ of pyritic waste material (<1% FeS₂). The highest concentrations of metals, lowest pH values and a very high daily release of H₂SO₄ (up to twice as high as the following month) were observed during the first week of thaw. This is considered a result of an accumulation of weathering products, generated within the waste pile during winter and released as a pollution-flush during early spring. Similar accumulation/flush sequences were observed later in the summer where rain events following relatively long dry periods caused high daily metal fluxes and on some occasions also elevated dissolved metal concentrations. Despite highly variable weather/climate conditions during the rest of the summer the investigated waste rock pile acted like a relative constant pollution-source during this period. Future investigations regarding the environmental impact of mine waste in the region should include measurements of bioavailable metals in order to provide further details on the seasonal trends in environmental impact.     

Geochemical hazard evaluation of sulphide-rich iron mines: The Rio Marina district (Elba Island,Italy)

Rio Marina mining district (Elba Island) is characterised by hematite + pyrite ore association and was exploited for iron till 1981, leaving waste rock dumps of several millions m³. The effect of open pit mining activity in this site is to produce acid mine drainage (AMD) processes leading to environmental pollution, testified by all the sampled waters (Giove stream, drainage channels, superficial pools and settling basin) which have pH values ranging from 2.08 to 3.35 and heavy metal concentrations that reach 903.16 mg/l for Fe, 45.02 mg/l for Mn, 10.08 mg/l for Zn and 1.75 mg/l for Cu. In the present work a space and time related approach to geochemical hazard evaluation was applied. The geochemical hazard is mainly related to high heavy metal concentration, acid mine drainage processes development and topographic setting. As all these parameters are related in space, hazard evaluation was performed by geostatistical methods. Fifty-four earth material samples (residual soils, waste rocks or debris materials) were collected in a central aligned 100 m mesh square grid. These were analysed for major elements by XRF, for Cu, Pb, Zn by ICP-AES and for AMD potential following the AMIRA procedure. The concentration of heavy metals was compared with Italian law limits. The overlap of Cu, Pb and Zn content maps show that at least one of these heavy metals exceed law limits in all the area. The AMD test results show that more than 50% of samples have a positive NAPP (Net Acid Producing Potential) that could reach 258.9 kg H₂SO₄/t. According to the obtained data, three main geochemical hazard classes were established and their distribution in the mining area was assessed. About 51% of the mining area surface belongs to the major hazard class, where AMD process occurs, about 49% belongs to an intermediate hazard class, where AMD process could occur only if certain conditions are met. Finally, the persistence of the AMD process in the Rio Marina area was evaluated on the basis of yearly rainfall, mining waters pH and NAPP values. A complete leaching of the first 0.25 m of the earth materials can retain the current environmental conditions for several centuries.     

Hydrological and geochemical control of metals and arsenic in a Mediterranean river contaminated by acid mine drainage (the Amous River,France); preliminary assessment of impacts on fish (Leuciscus cephalus)

Dissolved and particulate concentrations of metals (Fe, Al, Mn, Co, Ni, Cu, Zn, Cd, Tl, Pb) and As were monitored over a 5 year period in the Amous River downstream of its confluence with a creek severely affected by acid mine drainage (AMD) originating from a former Pb–Zn mine. Water pH ranged from 6.5 to 8.8. Metals were predominantly in dissolved form, except Fe and Pb, which were in particulate form. In the particulate phase, metals were generally associated with Al oxides, whereas As was linked to Fe oxides. Metal concentrations in the dissolved and/or particulate phase were generally higher during the wet season due to higher generation of AMD. Average dissolved (size < 0.22 μm) metal concentrations (μg/L) were 1 ± 4 (Fe), 69 ± 49 (Al), 140 ± 118 (Mn), 4 ± 3 Co, 6 ± 4 (Ni), 1.3 ± 0.8 (Cu), 126 ± 81 (Zn), 1.1 ± 0.7 (Cd), 0.9 ± 0.5 (Tl), 2 ± 3 (Pb). Dissolved As concentrations ranged from 5 to 134 μg/L (30 ± 23 μg/L). During the survey, the concentration of colloidal metals (5 kDa < size < 0.22 μm) was less than 25% of dissolved concentrations. Dissolved metal concentrations were generally higher than the maximum concentrations allowed in European surface waters for priority substances (Ni, Cd and Pb) and higher than the environmental quality standards for other compounds. Using Diffusion Gradient in Thin Film (DGT) probes, metals were shown to be in potentially bioavailable form. The concentrations in Leuciscus cephalus were below the maximum Pb and Cd concentrations allowed in fish muscle for human consumption by the European Water Directive. Amongst the elements studied, only As, Pb and Tl were shown to bioaccumulate in liver tissue (As, Pb) or otoliths (Tl). Bioaccumulation of metals or As was not detected in muscle.     

Enzymatic microbial Mn(II) oxidation and Mn biooxide production in the Guaymas Basin deep-sea hydrothermal plume

Microorganisms play important roles in mediating biogeochemical reactions in deep-sea hydrothermal plumes, but little is known regarding the mechanisms that underpin these transformations. At Guaymas Basin (GB) in the Gulf of California, hydrothermal vents inject fluids laden with dissolved Mn(II) (dMn) into the deep waters of the basin where it is oxidized and precipitated as particulate Mn(III/IV) oxides, forming turbid hydrothermal “clouds”. Previous studies have predicted extremely short residence times for dMn at GB and suggested they are the result of microbially-mediated Mn(II) oxidation and precipitation. Here we present biogeochemical results that support a central role for microorganisms in driving Mn(II) oxidation in the GB hydrothermal plume, with enzymes being the primary catalytic agent. dMn removal rates at GB are remarkably fast for a deep-sea hydrothermal plume (up to 2 nM/h). These rapid rates were only observed within the plume, not in background deep-sea water above the GB plume or at GB plume depths (∼1750-2000 m) in the neighboring Carmen Basin, where there is no known venting. dMn removal is dramatically inhibited under anoxic conditions and by the presence of the biological poison, sodium azide. A conspicuous temperature optimum of dMn removal rates (∼40 °C) and a saturation-like (i.e. Michaelis-Menten) response to O₂ concentration were observed, indicating an enzymatic mechanism. dMn removal was resistant to heat treatment used to select for spore-forming organisms, but very sensitive to low concentrations of added Cu, a cofactor required by the putative Mn(II)-oxidizing enzyme. Extended X-ray absorption fine structure spectroscopy (EXAFS) and synchrotron radiation-based X-ray diffraction (SR-XRD) revealed the Mn oxides to have a hexagonal birnessite or δ-MnO₂-like mineral structure, indicating that these freshly formed deep-sea Mn oxides are strikingly similar to primary biogenic Mn oxides produced by laboratory cultures of bacteria. Overall, these results reveal a vigorous Mn biogeochemical cycle in the GB hydrothermal plume, where a distinct microbial community enzymatically catalyzes rapid Mn(II) oxidation and the production of Mn biooxides.     

Geochemical comparison of waters and stream sediments close to abandoned Sb-Au and As-Au mining areas,northern Portugal

Waters from abandoned Sb-Au mining areas have higher Sb (up to 2138 μg L⁻¹), As (up to 1252 μg L⁻¹) and lower Al, Zn, Li, Ni and Co concentrations than those of waters from the As-Au mining area of Banjas, which only contain up to 64 μg L⁻¹ As. In general, Sb occurs mainly as SbO₃⁻ and As H₂AsO₄⁻. In general, waters from old Sb-Au mining areas are contaminated in Sb, As, Al, Fe, Cd, Mn, Ni and NO₂⁻, whereas those from the abandoned As-Au mining area are contaminated in Al, Fe, Mn, Ni, Cd and rarely in NO₂⁻. Waters from the latter area, immediately downstream of mine dumps are also contaminated in As. In stream sediments from Sb-Au and As-Au mining areas, Sb (up to 5488 mg kg⁻¹) and As (up to 235 mg kg⁻¹) show a similar behaviour and are mainly associated with the residual fraction. In most stream sediments, the As and Sb are not associated with the oxidizable fraction, while Fe is associated with organic matter, indicating that sulphides (mainly arsenopyrite and pyrite) and sulphosalts containing those metalloids and metal are weathered. Arsenic and Sb are mainly associated with clay minerals (chlorite and mica; vermiculite in stream sediments from old Sb-Au mining areas) and probably also with insoluble Sb phases of stream sediments. In the most contaminated stream sediments, metalloids are also associated with Fe phases (hematite and goethite, and also lepidocrocite in stream sediments from Banjas). Moreover, the most contaminated stream sediments correspond to the most contaminated waters, reflecting the limited capacity of stream sediments to retain metals and metalloids.     

Mn-Cr systematics of carbonates in CM chondrites: Implications for the timing and duration of aqueous alteration

CM chondrites contain carbonates and other secondary minerals such as phyllosilicates, sulfides, sulfates, oxides and hydroxides that are believed to have formed by aqueous alteration reactions on their parent asteroid. We report in situ Mn-Cr isotope measurements in the highly aqueously altered CM2.1 chondrites QUE 93005 and ALH 83100 using secondary ion mass spectrometry (Cameca ims-1270 ion microprobe). The ⁵³Cr excesses are correlated with the ⁵³Mn/⁵⁵Mn ratio and result from the in situ decay of ⁵³Mn, a short-lived radioisotope with a half-life of 3.7 Ma. If we assume that carbonate grains in samples QUE 93005 and ALH 83100 are cogenetic, then the excesses define initial ⁵³Mn/⁵⁵Mn ratios ((⁵³Mn/⁵⁵Mn)₀) of (4.1 ± 1.2) × 10⁻⁶ and (5.1 ± 1.7) × 10⁻⁶, respectively. These values are comparable to those in carbonates from other CM chondrites as reported in the literature. Initial ⁵³Mn/⁵⁵Mn ratios for calculated model isochrones for individual carbonate grains range from (3.8 ± 1.4) × 10⁻⁶ to (4.8 ± 2.1) × 10⁻⁶ for QUE 93005 and from (3.1 ± 1.6) × 10⁻⁶ to (1.3 ± 0.5) × 10⁻⁵ for ALH 83100. A possible interpretation for the ranges in (⁵³Mn/⁵⁵Mn)₀ could be that alteration in individual CM chondrites was episodic and occurred over an extended period of time. However, isochrones based on the entire set of carbonate grains in each of the CM chondrites imply that the degree of aqueous alteration is roughly correlated with the age of carbonate formation in CM chondrites of different subtypes and that alteration on the CM parent asteroid started contemporaneously with or shortly after CAI formation and lasted at least 4 Ma.     

Arsenic, iron and sulfur co-diagenesis in lake sediments

Profiles of porewater pH and dissolved As, Fe, Mn, sulfate, total sulfide (ΣS^−II), total zero-valent sulfur (ΣS⁰), organic carbon and major ion concentrations, as well as those of solid As, acid-volatile sulfide (AVS), total S, Fe, Mn, Al, organic C, ²¹⁰Pb and ¹³⁷Cs were determined in the sediment of four lakes spanning a range of redox and geochemical conditions. An inverse modeling approach, based on a one-dimensional transport-reaction equation assuming steady-state, was applied to the porewater As profiles and used to constrain the net rates of reactions involving As (). The model defines depth intervals where As is either released to (positive ) or removed from (negative ) the porewaters.At two of the sites, whose bottom water were oxygenated at sampling time, a production zone ( = 12 × 10⁻¹⁸ mol cm⁻³ s⁻¹-71 × 10⁻¹⁸ mol cm⁻³ s⁻¹) is inferred a few cm below the sediment-water interface, coincident with sharp porewater As and Fe peaks that indicate an intense coupled recycling of As and Fe. This process is confirmed by solid As and Fe maxima just below the sediment surface. In these two lakes a zone of As consumption ( = −5 × 10⁻¹⁸ mol cm⁻³ s⁻¹ to −53 × 10⁻¹⁸ mol cm⁻³ s⁻¹), attributed to the slow adsorption of As to authigenic Fe oxyhydroxides, occurs just above the production zone. A second-order rate constant of 0.12 ± 0.03 cm³ mol⁻¹ s⁻¹ is estimated for this adsorption reaction.Such features in the porewater and solid profiles were absent from the two other lakes that develop a seasonally anoxic hypolimnion. Thermodynamic calculations indicate that the porewaters of the four lakes, when sulfidic (i.e., ΣS^−II ? 0.1 μM), were undersaturated with respect to all known solid As sulfides; the calculation also predicts the presence of As^V oxythioanions in the sulfidic waters, as suggested by a recent study. In the sulfidic waters, the removal of As ( = −1 × 10⁻¹⁸ mol cm⁻³ s⁻¹ to −23 × 10⁻¹⁸ mol cm⁻³ s⁻¹) consistently occurred when saturation, with respect to FeS_(s), was reached and when As^V oxythioanions were predicted to be significant components of total dissolved As. This finding has potential implications for As transport in other anoxic waters and should be tested in a wider variety of natural environments.     

Mercury sources and transformations in a man-perturbed tidal estuary: The Sinnamary Estuary, French Guiana

The distribution, partition and speciation of mercury (Hg) were studied along the redox gradient of an anthropogenically perturbed tropical estuary, the Sinnamary Estuary in French Guiana. This system is a partially mixed estuary characterized by an anoxic freshwater end-member, while the marine end-member consists of the Amazon Plume.The set up of an artificial oxygenation system in the anoxic freshwater end-member generates sharp gradients of major chemical species (iron, sulfides, etc.) coupled with intense organic matter (OM) turnover. The coexistence of oxygenated waters and dissolved sulfides in an organic rich environment depicts the Upper Sinnamary Estuary (USE: part of Sinnamary Estuary under the tidal influence but upstream of the salt intrusion) as a potential site for Hg methylation. The concentrations of all mercury compounds (HgT) in the unfiltered samples (HgT_UNF), in the dissolved (HgT_D) and particulate (HgT_P) phases of the USE average 11 ± 3, 6 ± 2 and 5 ± 3 (i.e. 600 ± 200 pmol g⁻¹) pmol L⁻¹, respectively. Average concentrations of monomethylmercury (MMHg) in the unfiltered (MMHg_UNF), dissolved (MMHg_D) and particulate (MMHg_P) phases were 3.7 ± 1.0, 2.0 ± 0.9 and 1.8 ± 1.2 (i.e. 220 ± 130 pmol g⁻¹) pmol L⁻¹, respectively. Water oxygenation and sulfides concentrations emerged to play a critical role in controlling MMHg levels. Additionally, iron cycling, acid-base mechanisms, and redox-dependent processes were involved in the MMHg partitioning between phases.Overall, the USE constitutes a biogeochemical reactor that gathers partitioning and methylation processes. The permanent MMHg inputs from the anoxic freshwater end-member combined with the intense endogenous Hg methylation ensures high-MMHg levels in both dissolved and particulate phases. To illustrate, the USE exports 60 ± 20% more MMHg_UNF than it imports: 5.5 ± 0.7 vs. 3.5 ± 1.2 kg year⁻¹.     

Time and temperature dependency of carbon dioxide triggered metal(loid) mobilization in soil

Assessing the influence of CO₂ on soil and aquifer geochemistry is a task of increasing interest when considering risk assessment for geologic carbon sequestration. Leakage and CO₂ ascent can lead to soil acidification and mobilization of potentially toxic metals and metalloids due to desorption or dissolution reactions. We studied the CO₂ influence on an Fe(III) (oxyhydr)oxide rich, gleyic Fluvisol sampled in close vicinity to a Czech mofette site and compared the short-term CO₂ influence in laboratory experiments with observations on long-term influence at the natural site. Six week batch experiments with/without CO₂ gas flow at 3 different temperatures and monitoring of liquid phase metal(loid) concentrations revealed two main short-term mobilization processes. Within 1 h to 1 d after CO₂ addition, mobilization of weakly adsorbed metal cations occurred due to surface protonation, most pronounced for Mn (2.5–3.3 fold concentration increase, mobilization rates up to 278 ± 18 μg Mn kg_soil⁻¹ d⁻¹) and strongest at low temperatures. However, total metal(loid) mobilization by abiotic desorption was low. After 1–3 d significant Fe mobilization due to microbially-triggered Fe(III) (oxyhydr)oxide dissolution began and continued throughout the experiment (up to 111 ± 24 fold increase or up to 1.9 ± 0.6 mg Fe kg_soil⁻¹ d⁻¹). Rates increased at higher temperature and with a higher content of organic matter. The Fe(III) mineral dissolution was coupled to co-release of incorporated metal(loid)s, shown for As (up to 16 ± 7 fold, 11 ± 8 μg As kg_soil⁻¹ d⁻¹). At high organic matter content, re-immobilization due to resorption reactions could be observed for Cu. The already low pH (4.5–5.0) did not change significantly during Fe(III) reduction due to buffering from sorption and dissolution reactions, but a drop in redox potential (from > +500 mV to minimum +340 ± 20 mV) occurred due to oxygen depletion. We conclude that microbial processes following CO₂ induction into a soil can contribute significantly to metal(loid) mobilization, especially at optimal microbial growth conditions (moderate temperature, high organic carbon content) and should be considered for carbon sequestration monitoring and risk assessment.