Fast,green and effective chromium bio-speciation using <Emphasis Type="Italic">Sepia pharaonis</Emphasis> endoskeleton nano-powder

The development of a fast, effective, simple and low-cost procedure for chromium speciation is an analytical challenge. In this work, a new and simple method for speciation and determination of chromium species in different matrices was developed. Sepia pharaonis endoskeleton nano-powder was used as an adsorbent for the dispersive micro-solid-phase extraction. Finally, the desorbed chromium was determined using a graphite furnace atomic absorption spectrometer. The experimental results showed that Cr(III) could be quantitatively extracted by the adsorbent, while Cr(VI) adsorption was negligible. Concentrated H₂SO₄ and ethanol reduced Cr(VI)–Cr(III), and total chromium content was assessed as Cr(III). Then, the Cr(VI) concentration in the sample was calculated as the difference. The optimum conditions were obtained in terms of pH, adsorbent amount, contact time, and type, concentration and volume of eluent. Under the optimum conditions that involved the speciation of chromium ions from 25 mL of the water samples at pH 7.0 using 0.025 g of the adsorbent with contact time of 5 min, the method was validated in terms of linearity, precision and accuracy. The calibration curve was linear over the concentration range of 0.01–25.00 μg L^?1 for Cr(III). The obtained limit of detection for the proposed method was 0.003 µg L^?1. The maximum adsorption capacity of the adsorbent was found to be 995.57 mg g^?1. The proposed method was validated by the speciation of Cr(III) and Cr(VI) in different real water and wastewater samples with satisfactory results.     

Simultaneous phytoremediation of chromium and phenol by L<Emphasis Type="Italic">emna minuta</Emphasis> Kunth: a promising biotechnological tool

The aim of this work was to evaluate the usefulness of Lemna minuta Kunth for the simultaneous removal of Cr(VI) and phenol. The impact of these contaminants on plant growth and some biochemical processes have also been discussed for a better understanding and utilization of this species in the field of phytoremediation. The optimal growth conditions and plant tolerance to Cr(VI) and/or phenol as well as removal were determined. Plants exposed to Cr(VI) and phenol were able to efficiently grow and remove both contaminants at high concentrations (up to 2.5 and 250 mg/L, respectively) after 21 days, indicating that they were resistant to mixed contamination. There were no significant differences between chlorophyll, carotene and malondialdehyde content of treated plants with respect to the controls, which would be due to an efficient antioxidant response. L. minuta showed a higher biomass than control without contaminant when was exposed to low concentrations of Cr(VI), suggesting an hormesis effect. The main removal process involved in chromium phytoremediation would be sorption or accumulation in the biomass. Moreover, our results suggest that phenol could be used as a donor of carbon and energy by these plants. These findings demonstrated that Lemna minuta Kunth might be suitable for treatment of different solutions contaminated with Cr(VI) and phenol, showing a high potential to be used in the treatment of effluents containing mixed contamination.     

Thermoelastic properties of chromium oxide Cr<Subscript>2</Subscript>O<Subscript>3</Subscript> (eskolaite) at high pressures and temperatures

A new synchrotron X-ray diffraction study of chromium oxide Cr₂O₃ (eskolaite) with the corundum-type structure has been carried out in a Kawai-type multi-anvil apparatus to pressure of 15 GPa and temperatures of 1873 K. Fitting the Birch–Murnaghan equation of state (EoS) with the present data up to 15 GPa yielded: bulk modulus (K _0,T0), 206 ± 4 GPa; its pressure derivative K′_0,T , 4.4 ± 0.8; (?K _0,T /?T) = ?0.037 ± 0.006 GPa K^?1; a = 2.98 ± 0.14 × 10^?5 K^?1 and b = 0.47 ± 0.28 × 10^?8 K^?2, where α _0,T  = a + bT is the volumetric thermal expansion coefficient. The thermal expansion of Cr₂O₃ was additionally measured at the high-temperature powder diffraction experiment at ambient pressure and α _0,T0 was determined to be 2.95 × 10^?5 K^?1. The results indicate that coefficient of the thermal expansion calculated from the EoS appeared to be high-precision because it is consistent with the data obtained at 1 atm. However, our results contradict α ₀ value suggested by Rigby et al. (Brit Ceram Trans J 45:137–148, 1946) widely used in many physical and geological databases. Fitting the Mie–Grüneisen–Debye EoS with the present ambient and high-pressure data yielded the following parameters: K _0,T0 = 205 ± 3 GPa, K′_0,T  = 4.0, Grüneisen parameter (γ ₀) = 1.42 ± 0.80, q = 1.82 ± 0.56. The thermoelastic parameters indicate that Cr₂O₃ undergoes near isotropic compression at room and high temperatures up to 15 GPa. Cr₂O₃ is shown to be stable in this pressure range and adopts the corundum-type structure. Using obtained thermoelastic parameters, we calculated the reaction boundary of knorringite formation from enstatite and eskolaite. The Clapeyron slope (with \({\text{d}}P/{\text{d}}T = - 0.014\) GPa/K) was found to be consistent with experimental data.     

Chemical treatment of teff straw by sodium hydroxide,phosphoric acid and zinc chloride: adsorptive removal of chromium

In this study, teff (Eragrostis tef) straw has been chemically treated and tested as an adsorbent for Cr(VI) removal. Chemically treatment of teff straw was done by NaOH, H₃PO₄ and ZnCl₂ solutions. Scanning electron micrograph and X-ray diffraction were used for anatomical characterization, whereas Fourier transform infrared spectroscopy was used for surface change characterization of adsorbents. Effects of different experimental parameters like pH (2–12), initial Cr(VI) concentration (100–900 mg/L), adsorbent dose (2.5–20 g/L), contact time (15–360 min) and temperature (288–318 K) were studied. Temperature increment was found to stimulate the adsorption process. Langmuir isotherm was found to give better representation over wide range of temperature for untreated, H₃PO₄- as well as ZnCl₂-treated teff straw, and Freundlich isotherm best represented the isotherm data for NaOH-treated teff straw. Maximum Cr(VI) adsorption capacity of untreated, NaOH-, H₃PO₄- and ZnCl₂-treated teff straw was found to be 86.1, 73.8, 89.3 and 88.9 mg/g, respectively. Respective values of average effective diffusion coefficient (D _e) were found to be 2.8 × 10^?13, 2.59 × 10^?14, 1.32 × 10^?13 and 1.14 × 10^?13 m²/s, respectively. The negative value of ΔG _o for all the adsorbents indicates Cr(VI) spontaneous adsorption. Isosteric heat of adsorption (ΔH _st,a) was found to vary with surface coverage (θ). ΔH _st,a increased for untreated, H₃PO₄- and ZnCl₂-treated teff straw, and decreased steadily with θ for NaOH-treated teff straw.     

Formation of one-dimensional composites of poly(<Emphasis Type="Italic">m</Emphasis>-phenylenediamine)s based on <Emphasis Type="Italic">Streptomyces</Emphasis> for adsorption of hexavalent chromium

Here, a novel one-dimensional composite of poly(m-phenylenediamine)s coating on filamentous Streptomyces was successfully constructed via a controllable polymerization reaction. The synthesized composites were characterized by scanning electron microscopy, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy. Their adsorption isotherm and kinetics for aqueous hexavalent chromium were also systematically examined. The results of scanning electron microscopy analysis indicated that the obtained composites based on Streptomyces were showed a uniform and stable one-dimensional morphology with distinct core–shell configuration. Moreover, the Langmuir isotherm model (R ² > 0.96) and pseudo-second-order equation (R ² = 0.9996) described well the equilibrium adsorption behavior and kinetics of hexavalent chromium adsorption by the composites. In addition, bath adsorption experiments demonstrated the highest adsorption capacity of hexavalent chromium by the composites reached 320.03 mg g^?1 in an acid solution, which was 5.6 times as that of the pure Streptomyces filaments. The results of Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy analyses suggested that the adsorption of hexavalent chromium by the composites possibly involved the protonation, redox, and chelation reactions. Therefore, a promising application of these composites in treating acid hexavalent chromium-contaminated wastewater is expectable.     

Surface modification of <Emphasis Type="Italic">Nizimuddinia zanardini</Emphasis> and <Emphasis Type="Italic">Stoechospermum marginatum</Emphasis> using 4-phenyl-3-thiosemicarbazide to improve heavy metals biosorption from water

Surface modification of two algal biomasses, Nizimuddinia zanardini and Stoechospermum marginatum, using 4-phenyl-3-thiosemicarbazide ligand was performed to investigate the consequences on the adsorption of heavy metals from aqueous solution. Stabilization of amino group of 4-phenyl-3-thiosemicarbazide on the surface of biomasses was confirmed using Fourier transform infrared spectroscopy. Chemical modification was found to exert significant positive effects on biosorption. Adsorption capacities for Pb(II), Cd(II) and Cr(VI) using modified N. zanardini were observed to be 19.3, 16.75 and 15.75 mg/g, respectively, compared to 17.48, 14.18 and 11.85 mg/g for raw N. zanardini biomass. Also, adsorption of Pb(II), Cd(II) and Cr(VI) by the modified S. Marginatum was found to be 17.54, 15.62 and 14.77 mg/g, respectively, in comparison with that of the raw biomass which were 16.86, 12.9 and 11.2 mg/g. The obtained results of the equilibrium adsorption were studied through different isotherm models of Langmuir, Freundlich and Temkin, where the Langmuir model was observed to agree well with the results. Prevalent kinetic models including pseudo-second order and intra-particle diffusion were applied, and the pseudo-second order was found to describe the adsorption kinetics data adequately. Intra-particle model was also utilized in order to show penetration of metal ions, where it was realized that the biosorption took place in two or three steps including film diffusion, molecular diffusion and chemical reaction.     

Biosorption of hexavalent chromium from aqueous solution onto pomegranate seeds: kinetic modeling studies

Hexavalent chromium has been proved to be the reason of several health hazards. This study aimed at evaluating the application of pomegranate seeds powder for chromium adsorption (VI) from aqueous solution. Chromium adsorption percentage (VI) increased with increasing the adsorbent dosage. Chromium adsorption capacity (VI), at pH = 2 and 10 mg/L initial metal concentration, decreased from 3.313 to 1.6 mg/g through increasing dosage of adsorbent from 0.2 to 0.6 g/100 ml. The adsorption rate increased through increase in chromium initial concentration (VI). However, there was a removal percentage reduction of chromium (VI). Chromium adsorption kinetics by different models (pseudo-first-order, modified pseudo-first-order, pseudo-second-order, Elovich, intraparticle diffusion, Boyd kinetic) was investigated as well. Studies on adsorption kinetic indicated that the experimental data were matched by pseudo-second-order model (R ² = 0.999) better. Obtained results demonstrated the pomegranate seeds can be used as an effective biomaterial and biosorbent for hexavalent chromium adsorption from aqueous solutions.     

Compressibility of strontium orthophosphate Sr<Subscript>3</Subscript>(PO<Subscript>4</Subscript>)<Subscript>2</Subscript> at high pressure

High pressure in situ synchrotron X-ray diffraction experiment of strontium orthophosphate Sr₃(PO₄)₂ has been carried out to 20.0 GPa at room temperature using multianvil apparatus. Fitting a third-order Birch–Murnaghan equation of state to the P–V data yields a volume of V ₀ = 498.0 ± 0.1 Å³, an isothermal bulk modulus of K _T  = 89.5 ± 1.7 GPa, and first pressure derivative of K _T ′ = 6.57 ± 0.34. If K _T ′ is fixed at 4, K _T is obtained as 104.4 ± 1.2 GPa. Analysis of axial compressible modulus shows that the a-axis (K _a  = 79.6 ± 3.2 GPa) is more compressible than the c-axis (K _c  = 116.4 ± 4.3 GPa). Based on the high pressure Raman spectroscopic results, the mode Grüneisen parameters are determined and the average mode Grüneisen parameter of PO₄ vibrations of Sr₃(PO₄)₂ is calculated to be 0.30(2).     

High-pressure phase transitions of CaRhO<Subscript>3</Subscript> perovskite

High-pressure phase transitions of CaRhO₃ perovskite were examined at pressures of 6–27 GPa and temperatures of 1,000–1,930°C, using a multi-anvil apparatus. The results indicate that CaRhO₃ perovskite successively transforms to two new high-pressure phases with increasing pressure. Rietveld analysis of powder X-ray diffraction data indicated that, in the two new phases, the phase stable at higher pressure possesses the CaIrO₃-type post-perovskite structure (space group Cmcm) with lattice parameters: a = 3.1013(1) Å, b = 9.8555(2) Å, c = 7.2643(1) Å, V _m  = 33.43(1) cm³/mol. The Rietveld analysis also indicated that CaRhO₃ perovskite has the GdFeO₃-type structure (space group Pnma) with lattice parameters: a = 5.5631(1) Å, b = 7.6308(1) Å, c = 5.3267(1) Å, V _m  = 34.04(1) cm³/mol. The third phase stable in the intermediate P, T conditions between perovskite and post-perovskite has monoclinic symmetry with the cell parameters: a = 12.490(3) Å, b = 3.1233(3) Å, c = 8.8630(7) Å, β = 103.96(1)°, V _m  = 33.66(1) cm³/mol (Z = 6). Molar volume changes from perovskite to the intermediate phase and from the intermediate phase to post-perovskite are –1.1 and –0.7%, respectively. The equilibrium phase relations determined indicate that the boundary slopes are large positive values: 29 ± 2 MPa/K for the perovskite—intermediate phase transition and 62 ± 6 MPa/K for the intermediate phase—post-perovskite transition. The structural features of the CaRhO₃ intermediate phase suggest that the phase has edge-sharing RhO₆ octahedra and may have an intermediate structure between perovskite and post-perovskite.     

Potential of <Emphasis Type="Italic">Micranthemum umbrosum</Emphasis> for phytofiltration of organic arsenic species from oxic water environment

Arsenic (As) is a toxic and carcinogenic metalloid that causes various hazards to human health. Phytofiltration is a more eco-friendly and green approach than chemoremediation, or other traditional technologies, for removing As from aquatic environments. Recently, Micranthemum umbrosum was shown as a promising candidate for phytofiltration of inorganic As species. This work examines the potential application of M. umbrosum to phytofiltration of organic As species, such as monomethylarsonic acid (MMAA, CH₅AsO₃) and dimethylarsinic acid (DMAA, C₂H₇AsO₂), from oxic water environments. M. umbrosum plants were grown in two test concentrations of MMAA and DMAA, or a control, in a hydroponic experiment. After seven days, leaves accumulated 90 ± 3.2 and 48 ± 1.6 µg As g^?1 (oven dry basis) from 1 µg As mL^?1 of water added from MMAA and DMAA, respectively. Bioconcentration factor values and translocation factor values were always greater than 1.0, indicating that M. umbrosum was a good As accumulator and that leaves accumulated significantly higher amounts of As than stems and roots. Analysis of macro- and micronutrient data showed that M. umbrosum had higher resistance to organic As treatments than the control. These results confirm the potential application of M. umbrosum for phytofiltration of organic As from contaminated oxic water environments.     

Chromium(VI) adsorption by <Emphasis Type="Italic">Codium tomentosum</Emphasis>: evidence for adsorption by porous media from sigmoidal dose–response curve

Adsorption of Cr(VI) using native and chemically modified marine green macroalgae Codium tomentosum biomass and its adsorption kinetics were studied under specific conditions. Maximum Cr(VI) removal occurred at pH 2 for both untreated and acid-treated biomass. However, base-treated biomass exhibited maximum adsorption at pH 6 due to the hydrolysis of methyl esters present in the cellulose, hemicellulose and lignin molecules resulting in carboxyl groups (COO^?) on the surface. The effect of adsorbent dose revealed that untreated and acid-treated biomass follows Henry’s linear isotherm, while base-treated biomass exhibited sigmoidal curve indicating energetic heterogeneity on the adsorbing surface. The monolayer adsorption capacity of untreated, acid-treated and base-treated biomasses was 5.032 ± 0.644, 5.445 ± 0.947, 3.814 ± 0.559 mg g^?1, respectively. Adsorption was found to follow Ho and McKay’s pseudo-second-order kinetic model with decreasing pseudo-second-order rate constant (K ₂, g mg^?1 min^?1) of 0.088 ± 0.037 (acid-treated), 0.019 ± 0.003 (untreated) and 0.012 ± 0.003 (base-treated).     

Elastic behavior of vanadinite,Pb<Subscript>10</Subscript>(VO<Subscript>4</Subscript>)<Subscript>6</Subscript>Cl<Subscript>2</Subscript>, a microporous non-zeolitic mineral

The high-pressure behavior of a vanadinite (Pb₁₀(VO₄)₆Cl₂, a = b = 10.3254(5), c = 7.3450(4) Å, space group P6₃/m), a natural microporous mineral, has been investigated using in-situ HP-synchrotron X-ray powder diffraction up to 7.67 GPa with a diamond anvil cell under hydrostatic conditions. No phase transition has been observed within the pressure range investigated. Axial and volume isothermal Equations of State (EoS) of vanadinite were determined. Fitting the P–V data with a third-order Birch-Murnaghan (BM) EoS, using the data weighted by the uncertainties in P and V, we obtained: V ₀ = 681(1) Å³, K ₀ = 41(5) GPa, and K′ = 12.5(2.5). The evolution of the lattice constants with P shows a strong anisotropic compression pattern. The axial bulk moduli were calculated with a third-order “linearized” BM-EoS. The EoS parameters are: a ₀ = 10.3302(2) Å, K ₀(a) = 35(2) GPa and K′(a) = 10(1) for the a-axis; c ₀ = 7.3520(3) Å, K ₀(c) = 98(4) GPa, and K′(c) = 9(2) for the c-axis (K ₀(a):K ₀(c) = 1:2.80). Axial and volume Eulerian-finite strain (fe) at different normalized stress (Fe) were calculated. The weighted linear regression through the data points yields the following intercept values: Fe _a (0) = 35(2) GPa for the a-axis, Fe _c (0) = 98(4) GPa for the c-axis and Fe _V (0) = 45(2) GPa for the unit-cell volume. The slope of the regression lines gives rise to K′ values of 10(1) for the a-axis, 9(2) for the c-axis and 11(1) for the unit cell-volume. A comparison between the HP-elastic response of vanadinite and the iso-structural apatite is carried out. The possible reasons of the elastic anisotropy are discussed.     

Modified biomass of Phanerochaete chrysosporium immobilized on luffa sponge for biosorption of hexavalent chromium

Phanerochaete chrysosporium, a white rot basidiomycete, was immobilized over Luffa cylindrica sponge discs, treated with 0.1 N HCl and its potentiality for the removal of hexavalent chromium [Cr(VI)] from water was investigated in both batch and in up-flow fixed-bed bioreactor. The acid treatment of biomass increased the uptake capacity and percentage removal of Cr(VI) from 33.5 to 46.5 mg g^?1 and 67 to 92 %, respectively. Maximum uptake of Cr(VI) was achieved at pH 2, temperature 40 °C after 100 min of contact time. The Cr(VI) sorption on the biomass was better explained by Langmuir isotherm. Thermodynamic studies indicated that the process was spontaneous and endothermic. Sorption kinetic study showed that pseudo-second-order model best correlates the Cr(VI) sorption on the biomass as compare to pseudo-first-order kinetic model. The performance of fixed-bed bioreactor was evaluated at different bed heights (5, 15 and 25 cm) and flow rates (1.66, 4.98 and 8.33 mL min^?1) by using bed depth service time model. Response surface methodology statistical method was applied for optimizing the process parameters. FTIR analysis showed that amino groups were mainly involved in adsorption of Cr(VI).     

Seismic source characteristics in Kachchh and Saurashtra regions of Western India: <Emphasis Type="Italic">b</Emphasis>-value and fractal dimension mapping of aftershock sequences

Seismic source characteristics in the Kachchh rift basin and Saurashtra horst tectonic blocks in the stable continental region (SCR) of western peninsular India are studied using the earthquake catalog data for the period 2006–2011 recorded by a 52-station broadband seismic network known as Gujarat State Network (GSNet) running by Institute of Seismological Research (ISR), Gujarat. These data are mainly the aftershock sequences of three mainshocks, the 2001 Bhuj earthquake (M _w 7.7) in the Kachchh rift basin, and the 2007 and 2011 Talala earthquakes (M _w ≥ 5.0) in the Saurashtra horst. Two important seismological parameters, the frequency–magnitude relation (b-value) and the fractal correlation dimension (D _c) of the hypocenters, are estimated. The b-value and the D _c maps indicate a difference in seismic characteristics of these two tectonic regions. The average b-value in Kachchh region is 1.2 ± 0.05 and that in the Saurashtra region 0.7 ± 0.04. The average D _c in Kachchh is 2.64 ± 0.01 and in Saurashtra 2.46 ± 0.01. The hypocenters in Kachchh rift basin cluster at a depth range 20–35 km and that in Saurashtra at 5–10 km. The b-value and D _c cross sections image the seismogenic structures that shed new light on seismotectonics of these two tectonic regions. The mainshock sources at depth are identified as lower b-value or stressed zones at the fault end. Crustal heterogeneities are well reflected in the maps as well as in the cross sections. We also find a positive correlation between b- and D _c-values in both the tectonic regions.     

Sulfate Reduction and Sulfur Cycles at Two Seagrass Beds Inhabited by Cold Affinity <Emphasis Type="Italic">Zostera marina</Emphasis> and Warm Affinity <Emphasis Type="Italic">Halophila nipponica</Emphasis> in Temperate Coastal Waters

To evaluate the impact of invading seagrass on biogeochemical processes associated with sulfur cycles, we investigated the geochemical properties and sulfate reduction rates (SRRs) in sediments inhabited by invasive warm affinity Halophila nipponica and indigenous cold affinity Zostera marina. A more positive relationship between SRR and below-ground biomass (BGB) was observed at the H. nipponica bed (SRR = 0.6809 × BGB ? 4.3162, r ² = 0.9878, p = 0.0006) than at the Z. marina bed (SRR = 0.3470 × BGB ? 4.0341, r ² = 0.7082, p = 0.0357). These results suggested that SR was more stimulated by the dissolved organic carbon (DOC) exuded from the roots of H. nipponica than by the DOC released from the roots of Z. marina. Despite the enhanced SR in spring-summer, the relatively lower proportion (average, 20%) of acid-volatile sulfur (AVS) in total reduced sulfur and the strong correlation between total oxalate-extractable Fe (Fe_(oxal)) and chromium-reducible sulfur (CRS = 0.2321 × total Fe_(oxal) + 1.8180, r ² = 0.3344, p = 0.0076) in the sediments suggested the rapid re-oxidation of sulfide and precipitation of sulfide with Fe. The turnover rate of the AVS at the H. nipponica bed (0.13 day^?1) was 2.5 times lower than that at the Z. marina bed (0.33 day^?1). Together with lower AVS turnover, the stronger correlation of SRR to BGB in the H. nipponica bed suggests that the extension of H. nipponica resulting from the warming of seawater might provoke more sulfide accumulation in coastal sediments.     

Determination of atrazine isotherms on agricultural soils

For determination of atrazine isotherms in agricultural soils of Fars Province, composite soil samples from 0 to 5 cm depth with textures of silty clay loam, clay loam and loam were collected. In order to form the atrazine isotherms, 10, 50 and 100 µg atrazine g^?1 soil was added to the soil samples. Soluble atrazine in water:soil ratios of 10:1, 50:1 and 200:1 was measured after 3-h shaking. Finally, for each cases of applied atrazine, water extractable atrazine was determined and quantified using gas chromatography instrument. The results indicated that there was a linear relationship between the logarithms of water extractable atrazine and added atrazine for different water:soil ratios. A general equation of WEA = K(WS) ^α (AA) ^β is obtained experimentally between water extractable atrazine, µg g^?1(WEA), and added atrazine, µg g^?1 (AA), where K, α and β are absorption constants; WS is the water:soil ratio, g g^?1. For the loam, silty clay loam and clay loam soil textures, the α were 0.49, 0.23 and 0.13, respectively, the β were 0.55, 0.806 and 0.21, respectively, and the K were 1.44, 0.78 and 25.38, respectively.     

Stability at high-pressure,elastic behaviour and pressure-induced structural evolution of CsAlSi<Subscript>5</Subscript>O<Subscript>12</Subscript>, a potential host for nuclear waste

The elastic and structural behaviour of the synthetic zeolite CsAlSi₅O₁₂ (a = 16.753(4), b = 13.797(3) and c = 5.0235(17) Å, space group Ama2, Z = 2) were investigated up to 8.5 GPa by in situ single-crystal X-ray diffraction with a diamond anvil cell under hydrostatic conditions. No phase-transition occurs within the P-range investigated. Fitting the volume data with a third-order Birch–Murnaghan equation-of-state gives: V ₀ = 1,155(4) ų, K _T0 = 20(1) GPa and K′ = 6.5(7). The “axial moduli” were calculated with a third-order “linearized” BM-EoS, substituting the cube of the individual lattice parameter (a ³, b ³, c ³) for the volume. The refined axial-EoS parameters are: a ₀ = 16.701(44) Å, K _T0a = 14(2) GPa (β_a = 0.024(3) GPa^?1), K′ _a = 6.2(8) for the a-axis; b ₀ = 13.778(20) Å, K _T0b = 21(3) GPa (β_b = 0.016(2) GPa^?1), K′ _b = 10(2) for the b-axis; c ₀ = 5.018(7) Å, K _T0c = 33(3) GPa (β_c = 0.010(1) GPa^?1), K′ _c = 3.2(8) for the c-axis (K _T0a:K _T0b:K _T0c = 1:1.50:2.36). The HP-crystal structure evolution was studied on the basis of several structural refinements at different pressures: 0.0001 GPa (with crystal in DAC without any pressure medium), 1.58(3), 1.75(4), 1.94(6), 3.25(4), 4.69(5), 7.36(6), 8.45(5) and 0.0001 GPa (after decompression). The main deformation mechanisms at high-pressure are basically driven by tetrahedral tilting, the tetrahedra behaving as rigid-units. A change in the compressional mechanisms was observed at P ≤ 2 GPa. The P-induced structural rearrangement up to 8.5 GPa is completely reversible. The high thermo-elastic stability of CsAlSi₅O_12, the immobility of Cs at HT/HP-conditions, the preservation of crystallinity at least up to 8.5 GPa and 1,000°C in elastic regime and the extremely low leaching rate of Cs from CsAlSi₅O₁₂ allow to consider this open-framework silicate as functional material potentially usable for fixation and deposition of Cs radioisotopes.     

Thermal equation of state of CaIrO<Subscript>3</Subscript> post-perovskite

The pressure–volume–temperature (P–V–T) relation of CaIrO₃ post-perovskite (ppv) was measured at pressures and temperatures up to 8.6 GPa and 1,273 K, respectively, with energy-dispersive synchrotron X-ray diffraction using a DIA-type, cubic-anvil apparatus (SAM85). Unit-cell dimensions were derived from the Le Bail full profile refinement technique, and the results were fitted using the third-order Birth-Murnaghan equation of state. The derived bulk modulus \( K_{T0} \) at ambient pressure and temperature is 168.3 ± 7.1 GPa with a pressure derivative \( K_{T0}^{\prime } \) = 5.4 ± 0.7. All of the high temperature data, combined with previous experimental data, are fitted using the high-temperature Birch-Murnaghan equation of state, the thermal pressure approach, and the Mie-Grüneisen-Debye formalism. The refined thermoelastic parameters for CaIrO₃ ppv are: temperature derivative of bulk modulus \( (\partial K_{T} /\partial T)_{P} \) = ?0.038 ± 0.011 GPa K^?1, \( \alpha K_{T} \) = 0.0039 ± 0.0001 GPa K^?1, \( \left( {\partial K_{T} /\partial T} \right)_{V} \) = ?0.012 ± 0.002 GPa K^?1, and \( \left( {\partial^{2} P/\partial T^{2} } \right)_{V} \) = 1.9 ± 0.3 × 10^?6 GPa² K^?2. Using the Mie-Grüneisen-Debye formalism, we obtain Grüneisen parameter \( \gamma_{0} \) = 0.92 ± 0.01 and its volume dependence q = 3.4 ± 0.6. The systematic variation of bulk moduli for several oxide post-perovskites can be described approximately by the relationship K _T0  = 5406.0/V(molar) + 5.9 GPa.     

Chromium(VI) adsorption from aqueous solution by prepared biochar from <Emphasis Type="Italic">Onopordom Heteracanthom</Emphasis>

In this research, the stems of Onopordom Heteracanthom which is a kind of weed were converted to biochar particles, and their characteristics were investigated. The morphology and purity of these particles were examined by SEM and EDX techniques, respectively. Specific surface area was obtained as 5.73 m² g^?1 by BET method. The biochar particles obtained from Onopordom Heteracanthom were evaluated as an adsorbent to remove Cr(VI) from aqueous environments. The effect of some parameters such as initial concentration of Cr(VI), dosage of adsorbent, and pH were investigated on the adsorption capacity of Cr(VI) onto the adsorbent. The equilibrium data were analyzed by various isotherm models. The results revealed that in this process, the adsorption isotherm and kinetics have more conformity with Langmuir isotherm and pseudo-second-order kinetics, respectively. The multi-linearity of the Weber and Morris adsorption kinetic model indicates that the intra-particle diffusion is not merely the rate-controlling step for the whole adsorption process.     

Detection of <Emphasis Type="Italic">Salmonella typhi</Emphasis> using four developed kits of ELISA for cleaning in place purification

Lack of reliable knowledge to detect antigen of Salmonella typhi in water samples was our reason to modify ELISA method by alteration ratio of buffer-carbonated solution as new kits. Our study was assigned as six groups based on the different concentrations of S. typhi, 10⁴, 10⁶ and 10⁸ cells mL^?1 of S. typhi, one negative control, two positive controls and different buffer-carbonated solutions at dilution of 1:1000, 1:2000, 1:4000 and 1:8000 as our kits. The ODs of S. typhi were measured with the kits and compared to each other. GLM multivariate statistical analysis also was used for selecting more appropriate ELISA kit to measure more precise ODs of the bacteria concentrations. The closest calculated value to the OD value of 4 (positive control) was dedicated to kit 4 measured for positive control 1 (3.49 ± 0.00), positive control 2 (3.75 ± 0.00) and relatively similar (p > 0.05) to that of positive control 2 (3.27 ± 0.00) measured with kit 1. On the other hand, our results showed that great coefficient variations were measured with kit 1 as well as kits 2 and 3 for all groups except for negative controls. It is concluded that buffer-carbonated solution at dilution of 1:8000, as kit 4 is more capable of detecting S. typhi in water samples using ELISA method.