Seismic vertical uplift capacity of horizontal strip anchors using pseudo-dynamic approach

This paper presents the pseudo-dynamic analysis to determine the seismic vertical uplift capacity of a horizontal strip anchor using upper bound limit analysis. However, in the literature, the pseudo-static approach was used by few researchers to compute the seismic vertical pullout resistance, where the real dynamic nature of earthquake accelerations cannot be considered. Under the seismic conditions, the values of the unit weight component of uplift factor f_γE are determined for different magnitudes of soil friction angle, soil amplification, embedment ratio and seismic acceleration coefficients both in the horizontal and vertical directions. It is observed that the uplift factor f_γE decreases significantly with the increase in seismic accelerations and amplification but increases with the increase in embedment ratio. The results are compared with the existing values in the literature and the significance of the present methodology for designing the horizontal strip anchor is discussed. In presence of vertical earthquake acceleration and amplification of vibration, the present values of f_γE compare reasonably well with the existing pseudo-static values obtained by modifying the horizontal acceleration coefficient.     

Seismic Bearing Capacity of Shallow Strip Footing with Coulomb Failure Mechanism using Limit Equilibrium Method

In this paper, an effort is made to evaluate the seismic bearing capacity of shallow strip footing resting on c–ф soil. The formulation is developed to get a single coefficient of bearing capacity for simultaneous resistance of weight, surcharge and cohesion. Limit equilibrium method in Pseudo-static approach with Coulomb mechanism is applied here to evaluate the seismic bearing capacity. The seismic bearing capacity of footing (q_uE) is expressed in terms of single coefficient N_γE. The effect of various parameters viz. angle of internal friction of soil (ф), angle of wall friction (δ), cohesion (c), ratio of depth to width of footing (d_f/B₀), seismic acceleration (k_h, k_v) are studied on the variation of seismic bearing capacity co-efficients.     

The variation of Nγ with footing roughness using the method of characteristics

By using the method of characteristics, the effect of footing–soil interface friction angle (δ) on the bearing capacity factor N_γ was computed for a strip footing. The analysis was performed by employing a curved trapped wedge under the footing base; this wedge joins the footing base at a distance B_t from the footing edge. For a given footing width (B), the value of B_t increases continuously with a decrease in δ. For δ=0, no trapped wedge exists below the footing base, that is, B_t/B=0.5. On the contrary, with δ=?, the point of emergence of the trapped wedge approaches toward the footing edge with an increase in ?. The magnitude of N_γ increases substantially with an increase in δ/?. The maximum depth of the plastic zone becomes higher for greater values of δ/?. The results from the present analysis were found to compare well with those reported in the literature. Copyright © 2008 John Wiley & Sons, Ltd.     

Seismic bearing capacity of shallow strip footings

Seismic bearing capacity of shallow strip footings in soil has been obtained in the form of pseudo-static seismic bearing capacity factors N_cd, N_qd and N_d, denoting the cohesion, surcharge and unit weight components, respectively, by an extensive numerical iteration technique. Limit equilibrium method of analysis with composite failure surface is assumed. The validity of the principle of superposition is examined. Effects of both the horizontal and vertical seismic acceleration coefficients have been found to always reduce the ultimate bearing capacity significantly. Results obtained by the present method of analysis are compared with the available results and are found to be the least in the seismic case.     

Ultimate Bearing Capacity of a Footing Considering the Interference of an Existing Footing on Sand

The ultimate bearing capacity of a new strip footing placed on a cohesionless soil medium, in the presence of an existing strip footing, the load on which is assumed to be known, has been determined. Both the footings are assumed to be perfectly rigid and rough. The analysis is carried out by using an upper bound finite element limit analysis. For different clear spacing (S) between the footings, the values of the efficiency factor (ξ_γ) were determined; where ξ_γ is defined as the ratio of the failure load for an interfering new footing of a given width (B) to that for a single isolated footing having the same width. For ϕ < 30°, it is generally noted that the magnitude of ξ_γ increases continuously with a decrease in S/B. For ϕ > 30°, on the other hand if the applied load on the existing footing is approximately greater than half the failure load for a single isolated footing having the same width, the peak magnitude of ξ_γ was found to occur at around S/B ≈ 0.1 rather than at S/B = 0. The increase in ξ_γ becomes further significant with an increase in the magnitude of the load on the existing footing.     

Bearing capacity of a strip foundation on a sand layer overlying a smooth rigid stratum

The effect of a smooth rigid stratum, located beneath a dense sand layer, on the bearing capacity and settlement of surface and shallow strip footings is investigated using an advanced experimental model. A theoretical analysis is presented for the bearing capacity of surface footings. The results indicate that the bearing capacity reaches a minimum value at a specific sand-layer thickness. Any increase in the layer thickness above this value causes an increase in the bearing capacity up to that corresponding to a continuous media.Notation H= thickness of the sand layer - B= foundation width - N _q and N = bearing capacity factors for a semi-infinite layer - N _qs and N _s= bearing capacity factors for a finite layer - H _o /B= limiting depth - D _r= relative density - = angle of soil internal friction - M= model width - D= depth of surcharge - q= bearing stress, pressure applied on the footing - q _u= bearing capacity - = unit weight of sand     

Influence of random heterogeneity of the friction angle on bearing capacity factor Nγ

ABSTRACT

Probabilistic methods in geotechnical engineering have received a lot of attention during the last decade and different methodologies are used to capture the inherent variability of soil in different geotechnical engineering problems. In this paper, numerical simulations are conducted to obtain the bearing capacity factor, N_γ, for a purely frictional heterogenous soil where the friction angle is modelled as randomly distributed throughout the domain and the effect of its spatial variability on N_γ is investigated. A finite element method, based on the upper bound limit analysis was combined with random field theory and linear programming to develop a probabilistic analysis. Monte Carlo simulations were performed and the effect of the variability of the friction angle defined by statistical parameters on the bearing capacity factor was investigated. Results show that the mean bearing capacity factor N_γ of a footing on a spatially variable cohesionless soil is generally higher than the deterministic N_γ obtained from a constant mean value. Increasing the heterogeneity of the friction angle by an increase in the coefficient of variation generally increases this deviation. This can be explained by the nonlinearity of the relationship between N_γ and the friction angle.     

Reliability analysis of seismic bearing capacity of strip footing by stochastic slip lines method

In this research, the reliability analysis of seismic ultimate bearing capacity of strip footing is assessed with implementing slip lines method coupled with random field theory. The probability density functions of seismic and static bearing capacities which are log-normal and nearly normal distribution respectively are compared to each other. The predicted Probability Density Function (PDF) of the seismic bearing capacity by slip line method is verified, with those of the Terzaghi equation and Monte Carlo simulation (MCs). For uncertainties analysis by Terzaghi equation the N_c, N_q and N_γ are assessed stochastically.     

Bearing capacity of foundations on slopes

By applying the lower bound finite element limit analysis in conjunction with non-linear optimisation, the bearing capacity factors, N_c, N_q and N_γ, due to the components of cohesion, surcharge and unit weight, respectively, have been estimated for a horizontal strip footing placed along a sloping ground surface. The variation of N_c, N_q and N_γ with changes in slope angle (β) for different soil friction angle (φ) have been computed for smooth as well as rough strip footings. The analysis reveals that along a sloping ground surface, in addition to N_γ, the factors N_c and N_q also vary considerably with changes in footing roughness. Compared to the smooth footing, the extent of the plastic zone around the footing becomes greater for the rough footing. The results obtained from the analysis are found to compare well with those previously reported in literature.     

The influence of horizontal confinement on the bearing capacity factor Nγ of smooth strip footing

We studied the upper-bound ultimate bearing capacity of smooth strip shallow footings with symmetrical and asymmetrical horizontal confinements on purely frictional sand within the framework of upper-bound limit analysis. The subsoil follows the associated flow rule, and no surcharge on the soil surface is assumed. The contact between the soil and the horizontal confinement walls is assumed to be perfectly rough. The upper-bound solutions for the objective functions are obtained using nonlinear sequential quadratic programming. The results for the different internal friction angles φ are provided in terms of the variation of two parameters, namely, the bearing capacity factor N_γ and the correction factor of bearing capacity K_γ, with respect to the change in the clear spacing between the edge of smooth footing and the rigid vertical walls. The values of N_γ and K_γ increase with φ and decrease with the clear spacing between the edge of the smooth footing and the rigid vertical walls. N_γ and K_γ are more sensitive to this confining effect as φ increases. The numerical results, a comparative analysis with the results from previous studies, and design charts are also included.     

Upper bound limit analysis for finding interference effect of two nearby strip footings on sand

The ultimate bearing capacity of two closely spaced strip footings, placed on a cohesionless medium and loaded simultaneously to failure at the same magnitude of failure load, was determined by using an upper bound limit analysis. A logarithmic spiral radial shear zone, comprising of a number of triangular rigid blocks, was assumed to exist around each footing edge. The equations of the logarithmic spiral arcs were based on angles φ_L and φ_R rather than soil friction angle φ; the values of φ_L and φ_R were gradually varied in between 0 and φ. The ultimate bearing capacity was found to become maximum corresponding to a certain critical spacing between the footings. For spacing greater than the critical, the bearing capacity was found to decrease continuously with increase in the spacing. The extent of the spacing corresponding to which the ultimate bearing capacity becomes either maximum or equal to that of a single isolated footing increases with increase in φ. The results compare reasonably well with the available theoretical and experimental data.     

Bearing capacity factor, <Emphasis Type="Italic">N</Emphasis><Subscript><Emphasis Type="Italic">γ</Emphasis></Subscript>, for unsaturated soils by ZEL method

Bearing capacity of foundations is often determined for saturated state of the soil, regarding its simple and conservative results. This assumption, however, results in very uneconomic and overconservative design for a wide range of climates in the world. In this paper, plasticity equations were employed and extended for unsaturated soils to establish a theoretical approach to investigate the bearing capacity of unsaturated soils. It is achieved by combining the concept of effective stress and plasticity equations in terms of effective stress in unsaturated soils. The advantage of Bishop’s (4) effective stress concept was employed to simplify the equations. The equations were then transformed onto the zero extension lines directions to generalize this method for both associative and non-associative problems by which both stress and velocity field can be determined for unsaturated soils. A computer code was also developed to solve the relatively complex plasticity equations for a wide range of soil friction angles and matric suctions to compute the corresponding bearing capacity factor, N _γ , for strip foundations with smooth and rough base. This factor seems to be one of the major contributors in the bearing capacity of shallow foundations. The results have been presented in design charts and theoretical equations.     

Bearing capacity of strip foundations reinforced with geogrid sheets by using upper bound finite‐element limit analysis

By using the upper bound finite‐elements limit analysis, with an inclusion of single and two horizontal layers of reinforcements, the ultimate bearing capacity has been computed for a rigid strip footing placed over (i) fully granular, (ii) cohesive‐frictional, and (iii) fully cohesive soils. It is assumed that (i) the reinforcements are structurally strong so that no axial tension failure can occur, (ii) the reinforcement sheets have negligible resistance to bending, and (iii) the shear failure can take place between the reinforcement and soil mass. It is expected that the different approximations on which the analysis has been based would generally remain applicable for reinforcements in the form of geogrid sheets. A method has been proposed to incorporate the effect of the reinforcement in the analysis. The efficiency factors, η_c and η_γ, to be multiplied with N_c and N_γ , for finding the bearing capacity of reinforced foundations, have been established. The results have been obtained (i) for different values of ? in case of fully granular and cohesive‐frictional soils, and (ii) for different rates at which the cohesion increases with depth for a fully cohesive soil. The optimum positions of the reinforcements' layers have also been determined. The effect of the reinforcements' length on the results has also been analyzed. As compared to cohesive soils, the granular soils, especially with higher values of ?, cause a much greater increase in the bearing capacity. The results compare reasonably well with the available theoretical and experimental data from literature. Copyright © 2013 John Wiley & Sons, Ltd.     

Bearing capacity of strip and circular footings in sand using finite elements

Design of shallow foundations relies on bearing capacity values calculated using procedures that are based in part on solutions obtained using the method of characteristics, which assumes a soil following an associated flow rule. In this paper, we use the finite element method to determine the vertical bearing capacity of strip and circular footings resting on a sand layer. Analyses were performed using an elastic–perfectly plastic Mohr–Coulomb constitutive model. To investigate the effect of dilatancy angle on the footing bearing capacity, two series of analyses were performed, one using an associated flow rule and one using a non-associated flow rule. The study focuses on the values of the bearing capacity factors N_q and N_γ and of the shape factors s_q and s_γ for circular footings. Relationships for these factors that are valid for realistic pairs of friction angle and dilatancy angle values are also proposed.     

Bearing capacity of interfering multiple strip footings by using lower bound finite elements limit analysis

The ultimate bearing capacity of a number of multiple strip footings, identically spaced and equally loaded to failure at the same time, is computed by using the lower bound limit analysis in combination with finite elements. The efficiency factor (ξ_γ), due to the component of soil unit weight, is computed with respect to changes in the clear spacing (S) between the footings. It is noted that the failure load for a footing in the group becomes always greater than that of a single isolated footing. The values of ξ_γ for the smooth footings are found to be always lower than the rough footings. The values of ξ_γ are found to increase continuously with a decrease in the spacing between footings. As compared to the available theoretical and experimental results reported in literature, the present analysis provides generally a little lower values of ξ_γ.     

Bearing capacity computation for a ring foundation using the stress characteristics method

The stress characteristics method (SCM) has been used to compute the bearing capacity of smooth and rough ring foundations. Two different failure mechanisms for a smooth footing, and four different mechanisms for a rough footing have been considered. For a rough base, a curvilinear non-plastic wedge has been employed below the footing. The analysis incorporates the stress singularities at the inner as well as outer edges of the ring footing. Bearing capacity factors, N_c, N_q and N_γ are presented as a function of soil internal friction angle (ϕ) and the ratio (r_i/r_o) of inner to outer radii of the footing.     

A Simple Limit Equilibrium Approach for Calculation of Ultimate Bearing Capacity of Shallow Foundations on Two-Layered Granular Soils

The bearing capacity of shallow foundations in a non-homogeneous soil profile has been a challenging task in geotechnical engineering. In this paper, a limit equilibrium method is used for calculating bearing capacity factors of shallow foundations constructed on a two-layered granular soil profile. The main objective has been to determine the ultimate bearing capacity computed from equivalent bearing capacity factors N_q and N_γ and comparing that with numerical analysis using finite element methods. It will be shown that the data obtained form the developed method are well comparable with those obtained from FE approach, specially when the difference between shear strength parameters of layers is low which is a practical case for sedimentary soil profiles and also for artificially compacted soils. A computer program has been developed to investigate the influence of various parameters on bearing capacity factors.     

Behaviour of model footing on pond ash

This paper focuses on the effective utilization of pond ash, as foundation medium. A series of laboratory model tests have been carried out using square, rectangular and strip footings on pond ash. The effects of dry density, degree of saturation of pond ash, size and shape of footing on ultimate bearing capacity of shallow foundations are presented in this paper. Local shear failure of a square footing on pond ash at 37% moisture content (optimum moisture content) is observed up to the values of dry density 11.20 kN/m³ and general shear failure takes place at the values of dry density 11.48 kN/m³ and 11.70 kN/m³. Effects of degree of saturation on ultimate bearing capacity were studied. Experimental results show that degree of saturation significantly affects the ultimate bearing capacity of strip footing. The effect of footing length to width ratio (L/B), on increase in ultimate bearing capacity of pond ash, is insignificant for L/B ≥ 10 in case of rectangular footings. The effects of size of footing on ultimate bearing capacity for all shapes of footings viz., square, rectangular and strip footings are highlighted.     

Bearing Capacity of Strip Footings Near Slopes

In the last decades a great attention was given by many authors to the evaluation of the static and seismic bearing capacity of footings near slopes. In this paper a model has been developed based on the limit equilibrium method, considering a circular surface propagates towards the slope until the sloping ground is reached. The bearing capacity is investigated considering either the distance of the footing from the edge of the slope and/or the effect of the footing embedment. A validation of the proposed model was made by a comparison with solutions taken from literature regarding the evaluation of the bearing capacity for a footing adjacent to a slope and for an inclined load. The loading conditions consist in vertical and horizontal stress on the footing and on the soil below the footing. Both the inertial and kinematic effects of the seismic loading have been analyzed, and a simple equation has been derived for the evaluation of the seismic bearing capacity. The static and seismic bearing capacity has been investigated as a function of the soil friction angle, of the seismic coefficient, of the sloping ground. Finally, the influence of the distance of the footing from the edge of the slope was taken into consideration in the evaluation of the bearing capacity, and a threshold distance at which the reduction of the bearing capacity due to the sloping ground vanishes has been defined.     

Pseudo-static Seismic Bearing Capacity of Shallow Foundations in Unsaturated Soils Employing Limit Equilibrium Method

There exist many structures founded on unsaturated soil deposits. Shear strength augmentation due to the evolution of the matric suction within the unsaturated porous media enhances the bearing capacity of the overlying foundation. This paper presents the evaluation of the pseudo-static seismic bearing capacity of the shallow foundations resting on unsaturated soil deposits using limit equilibrium method. Adopting the Coulomb failure mechanism and Bishop effective stress concept, the bearing capacity equations are solved. The distribution of the matric suction beneath the footing is assumed to be linear. The results of the bearing capacity evaluation are validated against some experimental data found in literature for the static condition. For the seismic loading consideration, the pseudo-static method is utilized. The dual effect of the earthquake acceleration vertical component is thoroughly discussed and a suction transition point is introduced in which the minimum bearing capacity is observed to bear the same value for both upward and downward directions. The increase in the matric suction throughout the soil deposit leads to the increase in the soil shear strength, thus posing more resisting forces as well as higher ultimate bearing capacity. The offered solution is deemed a consistent and useful tool for the accurate prediction of the seismic bearing capacity of shallow footings resting on unsaturated soil deposits.