Mitigation of the amplitude and celerity of dam break shock wave using combination of groyne and vertical pier

This paper aims to numerically investigate the impact of the combination of groynes and vertical piers on mitigating the amplitude and celerity of dam break wave-front. First, a robust numerical model based on the Finite Volume Method(FVM) with the Harten, Lax and van Leer(HLL) approximate Reimann's solver's technique is developed and validated with other research studies. Then many different scenarios including group of piers, group of groynes with different shapes and combination of groynes and piers are considered for dam break flow modeling. The final results showed that group of piers alone or group of groynes alone have no significant effects on the wave-front depth and celerity but, combination of L-head groyne with piers can decrease the amplitude and celerity of the dam break wavefront or flood wave. In this case, a blockage zone between the groynes and intensive backwater effects behind them were observed.     

Influence of inflow discharge and bed erodibility on outburst flood of landslide dam

Accurate prediction of the hydrographs of outburst floods induced by landslide dam overtopping failure is necessary for hazard prevention and mitigation. In this study, flume model tests on the breaching of landslide dams were conducted. Unconsolidated soil materials with wide grain size distributions were used to construct the dam. The effects of different upstream inflow discharges and downstream bed soil erosion on the outburst peak discharge were investigated. Experimental results reveal that the whole hydrodynamic process of landslide dam breaching can be divided into three stages as defined by clear inflection points and peak discharges. The larger the inflow discharge, the shorter the time it takes to reach the peak discharge, and the larger the outburst flood peak discharge. The scale of the outburst floods was found to be amplified by the presence of an erodible bed located downstream of the landslide dam. This amplification decreases with the increase of upstream inflow. In addition, the results show that the existence of an erodible bed increases the density of the outburst flow, increasing its probability of transforming from a sediment flow to a debris flow.     

Hydrological Response to Environment Change in Himalayan Watersheds: Assessment from Integrated Modeling Approach

Land use changes such as deforestation,increase in cropping or grazing areas and built-up land, likely modify the water balance and land surface behavior in the Himalayan watersheds.An integrated approach of hydrological and hydraulic modeling was adopted for comparative analysis of hydrological pattern in three Himalayan watersheds i.e.Khanpur,Rawal and Simly situated in the Northern territory of Pakistan.The rainfall-runoff model SWAT- Soil and water assessment tool and Hydro CAD were calibrated for the selected watersheds.The correlation analysis of the precipitation data of two climate stations i.e.Murree and Islamabad, with the discharge data of three rivers was utilized to select best suitable input precipitation data for Hydro CAD rainfall-runoff modeling.The peak flood hydrograph were generated using Hydro CAD runoff to optimize the basin parameters like CN, runoff volume, peak flows of the three watersheds.The hydrological response of the Rawal watershed was studied as a case study to different scenarios of land use change using SWAT model.The scenario of high deforestation indicated a decline of about 6.3% in the groundwater recharge tostream while increase of 7.1% in the surface runoff has been observed under the scenario of growth in urbanization in the recent decades.The integrated modeling approach proved helpful in investigating the hydrological behavior under changing environment at watershed level in the Himalayan region.     

Centrifugal model tests and numerical simulations for barrier dam break due to overtopping

The present study focuses on the breaching process and failure of barrier dams due to overtopping. In this work, a series of centrifugal model tests is presented to examine the failure mechanisms of landslide dams. Based on the experimental results, failure process and mechanism of barrier dam due to overtopping are analyzed and further verified by simulating the experimental overtopping failure process. The results indicate that the barrier dam will develop during the entire process of overtopping in the width direction, whereas the breach will cease to develop at an early stage in the depth direction because of the large particles that accumulate on the downstream slope. Moreover, headcut erosion can be clearly observed in the first two stages of overtopping, and coarsening on the downstream slope occurs in the last stage of overtopping. Thus, the bottom part of the barrier dam can survive after dam breaching and full dam failure becomes relatively rare for a barrier dam. Furthermore, the remaining breach would be smaller than that of a homogeneous cohesive dam under the same conditions.     

济南市东湖水库地质灾害预测

济南市东湖水库库区不具备发生崩塌、滑坡、地面塌陷、地面沉降、泥石流、地裂缝、砂土液化的地质环境条件。水库建成使用后，可能出现坝后浸没、次生盐渍化及坝体不均匀沉降等地质灾害，应采取工程措施。     

Analysis and evaluation on seepage stability of Hongxing reservoir dam , Heilongjiang

Hongxing reservoir was constructed on the floodplain of Hulan River in Heilongjiang. The geological problem of the reservoir is the seepage of the dam base and its related seepage stability. The leakage of the reservoir is caused by the water head differences between the upstream and downstream of the dam. Severe seepage could decrease the engineering benefits of the reservoir. Moreover, infiltration function of water will influence the safety of the dam. Through the analysis on the granule constitute and the formation of the dam base, the types of the seepage failure apt to happen were defined and the anti-infiltration and the permissible depression ratio were determined. Using the numerical simulation software GMS, the two-dimension numerical modeling has been carried out to analyze the seepage field of the reservoir. Through the two conditions modeling with concrete impervious wall and no concrete impervious wall, the largest flow rate, single-wide seepage discharge and the max infiltration gradient of the dam base were calculated. According to the permeable depression ratio of the dam base, the seepage stability of Hongxing reservoir dam base was analyzed.     

Characteristics and interpretation of the seismic signal of a field-scale landslide dam failure experiment

Outburst floods caused by breaches of landslide dams may cause serious damages and loss of lives in downstream areas; for this reason the study of the dynamic of the process is of particular interest for hazard and risk assessment. In this paper we report a field-scale landslide dam failure experiment conducted in Nantou County, in the central of Taiwan.The seismic signal generated during the dam failure was monitored using a broadband seismometer and the signal was used to study the dam failure process.We used the short-time Fourier transform(STFT) to obtain the time–frequency characteristics of the signal and analyzed the correlation between the power spectrum density(PSD) of the signal and the water level. The results indicate that the seismic signal generated during the process consisted of three components: a low-frequency band(0–1.5 Hz), an intermediate-frequency band(1.5–10 Hz) and a highfrequency band(10–45 Hz). We obtained the characteristics of each frequency band and the variations of the signal in various stages of the landslide dam failure process. We determined the cause for the signal changes in each frequency band and its relationship with the dam failure process. The PSD sediment flux estimation model was used to interpret the causes of variations in the signal energy before the dam failure and the clockwise hysteresis during the failure. Our results show that the seismic signal reflects the physical characteristics of the landslide dam failure process. The method and equipment used in this study may be used to monitor landslide dams and providing early warnings for dam failures.     

Analysis on dam-breaking mode of Tangjiashan barrier dam in Beichuan county

Tangjiashan landslide is a typical high-speed consequent landslide of medium-steep dip angle. This landslide triggered by earthquake took place in about semi-minute. The relative sliding displacement is 900 meters, so average sliding speed is about 30 meters per second. The longitudinal length of barrier dam which is formed by high-speed landslide along river is 803.4 meters; and maximum width crossing river is 611.8 meters. And its volume is estimated about 20.37 million steres. Through detailed geological investigation of the barrier dam, together with early geological information before earthquake, geological structures of the barrier dam and its stability of upstream and downstream slopes are studied when water level reaches different elevations in condition of continual after shocks with seismic intensity of 7 or 8 Richter scale. On this basis, dam-breaking mode of barrier dam is discussed deeply. Thereby, analytic results provide significant guidance and advices to front headquarters of Tangjiashan barrier dam, so that some proper engineering measures can be implemented and flood discharge can be carried out well.     

Failure mechanism and stability analysis of the Zhenggang landslide in Yunnan Province of China using 3D particle flow code simulation

Based on the principle of 3D particle flow code, a numerical landslide run-out model is presented to simulate the failure process of the Zhenggang landslide (in southwestern China) under the effect of water after a rainfall. The relationship between the micro-mechanical parameters and the macro-shear strength of the grain material is determined through numerical calibrations. Then the rainfall effect is considered in numerical simulations and rain-induced sliding processes are performed, which help us to discuss the mechanism of deformation and failure of this landslide together with field observations. It shows the Zhenggang landslide would most likely be activated in Zone I and would gain momentum in Zone II. In order to prevent the potential disaster, a tailing dam is advised to be designed about 175 m downstream from the current landslide boundary of Zone II. Verified by field observations, the presented landslide model can reflect the failure mechanism after rainfall. It can also provide a method to predict the potential disaster and draft disaster prevention measures.     

Local scour and the laws of scour pit’s shape downstream of debris flow sabo dam

The erosion shape and the law of development of debris flow sabo dam downstream is a weak part in the study on debris flow erosion. The shape and development of scour pit have an important effect on the stability and safety of debris flow sabo dam, which determines the foundational depth of the dam and the design of protective measures downstream. Study on the scouring law of sabo dam downstream can evaluate the erosion range and reasonably arrange auxiliary protective engineering. Therefore, a series of flume experiments are carried out including different debris flow characteristics （density is varying from 1.5 t/m3 to 2.1 t/m~） and different gully longitudinal slopes. The result shows that the scour pit appears as an oval shape in a plane and deep in the middle while superficial at the ends in the longitudinal section, the position of the maximum depth point moves towards downstream with an increase of flume slope angle. The maximum depth of scour pit is mainly affected by the longitudinal slope of gully, density of debris flow, and the characteristics of gully composition （particle size and the viscosity of soil）. The result also indicates that the viscosity of soil will weaken the erosion extent. The interior slopes of scour pit are different between the upstream and the downstream, and the downstream slope is smaller than the upper one. For the viscous and non-viscous sands with the same distribution of gradation, the interior slope of non- viscous sand is smaller than the viscous sand.According to tbe regression analysis on the experimental data, the quantitative relationship between the interior slope of scour pit, slope of repose under water and the longitudinal slope of gully is established and it can be used to calculate the interior slope of scour pit. The results can provide the basis for the parameter design of the debris flow control engineering foundation.     

A High Precision Comprehensive Evaluation Method for Flood Disaster Loss Based on Improved Genetic Programming

Precise comprehensive evaluation of flood disaster loss is significant for the prevention and mitigation of flood disasters. Here, one of the difficulties involved is how to establish a model capable of describing the complex relation between the input and output data of the system of flood disaster loss. Genetic programming （GP） solves problems by using ideas from genetic algorithm and generates computer programs automatically. In this study a new method named the evaluation of the grade of flood disaster loss （EGFD） on the basis of improved genetic programming （IGP） is presented （IGP-EGFD）. The flood disaster area and the direct economic loss are taken as the evaluation indexes of flood disaster loss. Obviously that the larger the evaluation index value, the larger the corresponding value of the grade of flood disaster loss is. Consequently the IGP code is designed to make the value of the grade of flood disaster be an increasing function of the index value. The result of the application of the IGP-EGFD model to Henan Province shows that a good function expression can be obtained within a bigger searched function space; and the model is of high precision and considerable practical significance. Thus, IGP-EGFD can be widely used in automatic modeling and other evaluation systems.     

福建东圳库区淹没及水土流失的3D-VRGIS构建与应用

本文应用VRGIS(Virtual Reality Geographical Information System)技术,建立水库工程水土流失三维可视化动态仿真模型,实现库区的空间信息可视化。以福建省东圳水库为研究对象,建立水土流失区域三维虚拟地理信息系统(3D-VRGIS),生成水土流失现状以及库区生态环境三维场景。并结合水土流失中水淹分析要素与三维空间的数据可视化技术,实现水土流失监测预报及其区域定位监控的可视化处理,为减少水土流失危害,提供可靠的信息资源。     

滑坡堰塞坝堆积形态影响因素离散元分析

滑坡是形成堰塞坝的最主要原因,在地震、降雨、冰雪融水等作用下均可形成滑坡堰塞坝,而滑坡堰塞坝的堆积形态、范围等对评价堰塞坝的稳定性有着重要的影响。通过离散元方法(DEM),系统分析了三维条件下滑动距离、滑面出口宽度、滑面倾角、河床倾角、河谷形状对堰塞坝堆积形态的影响。研究结果表明:滑动距离和出口宽度对坝体高度影响最大;随出口宽度和坡面倾角的增加,坝长和坝宽分别呈线性增大和减小趋势;滑动距离可以有效控制滑体速度,进而影响堆积角大小;河床倾角主要影响坝长;对坝高、坝长、上下游绝对倾角正切值和堆积角正切值进行回归分析表明,数学模型契合程度高,说明其形态可以预测;引入2个参数λ和χ,对堰塞坝堆积特征进行了描述;河谷形状的影响主要体现在随着河谷底部宽度的增大,滑体爬高爬坡能力增强。研究成果对根据实际地形预测滑坡堰塞坝堆积形态进而评估坝体的安全性具有重要意义,可以为进一步开展堰塞湖溃决研究提供一定的参考。      

Rapid geometry analysis for earthquake-induced and rainfall-induced landslide dams in Taiwan

Stability analysis of the dam is important for disaster prevention and reduction. The dam＇s geometry plays an important role in understanding its stability. This study develops a rapid landslide dam geometry assessment method for both earthquake-induced and rainfall-induced landslide dams based on nine real cases collected in Chinese Taipei and 214 cases collected worldwide. For simplification purposes, a landslide dam is classified into triangular or trapezoidal. The rapid landslide dam geometry assessment method in this paper uses only satellite maps and the topographic maps to get landslide area, and then analyze the dam geometry. These maps are used to evaluate the area of the landslide and the slope of the river bed. Based on the evaluation information, the proposed method can calculate dam height, the length of the dam, and the angles of the dam in both upstream and downstream directions. These geometry parameters of a landslide dam provide important information for further dam stability analysis. The proposed methodology is applied to a real landslide dam case at Hsiaolin Village. The result shows that the proposed method can be used to assess the landslide dam geometry.     

一种洪涝灾害事件信息建模方法

我国洪涝灾害频发且危害巨大,为有效防灾、减灾和救灾,需建立洪涝灾害事件信息模型,表示和共享洪涝灾害信息。然而,目前事件信息模型主要是表示静态信息,缺乏对洪涝灾害事件动态过程的表示。本文从观测角度出发,建立顾及洪涝灾害事件阶段和动态过程的洪涝灾害事件信息模型。围绕洪涝灾害事件信息模型,提出了10类需建模的元素,并以MOF（Meta Object Facility）建模框架构建了十元组模型,通过映射方法实现模型编码方案与事件模式语言的映射。最后,以2010年梁子湖洪涝灾害模拟为例,开展了模型分阶段建立过程实验。结果表明,本文提出的模型能表示洪涝灾害事件的动态信息和实现洪涝灾害事件的动态建模。     

Dam-break Modeling in Alpine Valleys

Dam-break analysis is of great importance in mountain environment,especially where reservoirs are located upstream of densely populated areas and hydraulic hazard should be assessed for land planning purposes.Accordingly,there is a need to identify suitable operative tools which may differ from the ones used in flat flood-prone areas.This paper shows the results provided by a 1D and a 2D model based on the Shallow Water Equations（SWE） for dam-break wave propagation in alpine regions.The 1D model takes advantage of a topographic toolkit that includes an algorithm for pre-processing the Digital Elevation Model（DEM） and of a novel criterion for the automatic cross-section space refinement.The 2D model is FLO-2D,a commercial software widely used for flood routing in mountain areas.In order to verify the predictive effectiveness of these numerical models,the test case of the Cancano dam-break has been recovered from the historical study of De Marchi（1945）,which provides a unique laboratory data set concerning the consequences of the potential collapse of the former Cancano dam（Northern Italy）.The measured discharge hydrograph at the dam also provides the data to test a simplified method recently proposed for the characterization of the hydrograph following a sudden dam-break.     

Outburst risk of barrier lakes in Sichuan,China

34 barrier lakes induced by earthquake have been formed by wedged debris on the river channels after a massive earthquake happening on May 12 in Sichuan, China. Among them, the Tangjiashan Barrier Lake is the largest one. It faces very urgent risk of dam breaking when water level reaches the top and begins overflow in case of storm rainfalls and continually aftershocks, threatening already devastated cities and villages with about 1.5 million people downstream. The outburst of a similar barrier lake occurred in the Minjiang River in 1933, causing a catastrophic flood. Risk analysis indicates that not all barrier lakes are highly dangerous. Only those lakes with very high dams and water to be filled up in short period need to be dealt with immediately.     

Numerical model for homogeneous cohesive dam breaching due to overtopping failure

Based on the large-scale model tests, a simplified dam breach model for homogeneous cohesive dam due to overtopping failure is put forward. The model considers headcut erosion as one of the key homogeneous cohesive dam breaching mechanisms and we calculate the time-averaged headcut migration rate using an energy-based empirical formula. A numerical method is adopted to determine the initial scour position at the downstream slope in terms of the water head and dam height, and the broad-crested weir equation is utilized to simulate the breach flow. The limit equilibrium method is used to analyze the stability of breach slope during the breach process. An iterative method is developed to simulate the coupling process of soil and water at each time step. The calculated results of three dam breach cases testify the reasonability of the model, and the sensitivity studies of soil erodibility show that sensitivity is dependent on each test case’s soil conditions. In addition, three typical dam breach models, NWS BREACH, WinDAM B, and HR BREACH, are also chosen to compare with the proposed model. It is found that NWS BREACH may have large errors for cohesive dams, since it uses a noncohesive sediment transport model and does not consider headcut erosion, WinDAM B and HR BREACH consider headcut erosion as the breaching mechanism and handle well homogeneous cohesive dam overtopping failure, but overall, the proposed model has the best performance.     

基于元胞自动机模型的河道汇流过程模拟

对河道汇流过程进行模拟可为洪水灾害预警预报提供参考。利用水力水文学方法能很好地模拟河道汇流过程,但需要输入的参数多,运算过程复杂,对数据精度要求高,而且在无资料区流域无法确定河道上断面流量情况下,该方法具有一定局限性。本文将元胞自动机模型与水文模型相结合,构建了河道汇流过程中的元胞自动机模型和产流汇流规则。通过建立河道坡面拓扑关系,利用SCS-CN（Soil Conservation Service-Curve Number）模型逐个计算河道元胞上的坡面入流,并利用曼宁方程模拟河道汇流过程,最后在ArcEngine平台下进行二次开发,实现了河道汇流可视化。本文以厦门市茂林溪流域为研究区,对1997年5月6日至7日的一场降雨进行了模拟。将本文模拟结果与该流域其他学者的研究进行了对比分析,结果表明在输入数据与水文模型参数相同的情况下,本文不仅模拟出每次降雨间隔产生的较小洪峰,并且整场降雨产生的最大洪峰流量精度与时间精度均提高了5倍,可以更准确地模拟河道汇流过程,适用于河道汇流可视化,该模拟可以为洪水灾害预警预报提供一定参考。     

Seismic deformation and seismic resistance analysis of Shapai Roller Compacted Concrete Arch Dam based on field monitoring and dynamic finite element method

Shapai Roller Compacted Concrete(RCC) Arch Dam is the highest RCC arch dam of the 20th century in the world with a maximum height of 132m,and it is the only concrete arch dam near the epicentre of Wenchuan earthquake on May 12th,2008.The seismic damage to the dam and the resistance of the dam has drawn great attention.This paper analyzed the response and resistance of the dam to the seismic wave using numerical simulations with comparison to the monitored data.The field investigation after the earthquake and analysis of insitu data record showed that there was only little variation in the opening size at the dam and foundation interface,transverse joints and inducing joints before and after the earthquake.The overall stability of the dam abutment resistance body was quite good except a little relaxation was observed.The results of the dynamic finite element method(FEM) showed that the sizes of the openings obtained from the numerical modeling are comparable with the monitored values,and the change of the opening size is in millimeter range.This study revealed that Shapai arch dam exhibited high seismic resistance and overload capacity in the Wenchuan earthquake event.The comparison of the monitored and simulated results showed that the numerical method applied in this paper well simulated the seismic response of the dam.The method could be useful in the future application on the safety evaluation of RCC dams.