Leaching capabilities of iodine monochloride (ICl) and diethylenetriamine pentaacetic acid (DPTA) at different concentrations and pH for some major and trace metals from coal and coal fly ash

In the present study, coal from Chakwal (Pakistan) was leached with an aqueous solutions of iodine monochloride (ICl) and diethylenetriamine pentaacetic acid (DPTA) of different concentrations. The effect of stirring time, concentration and pH was studied on the leaching of different metals from coal. The physicochemical parameters indicated that the coal was of reasonably good quality. The results indicated that with increase in time duration, the extraction of metals increased. In most of the cases, metal concentration increased in the leachate with increasing the concentration of the leaching agents. DPTA was found to be the best leaching agent for most of the metals. Higher extraction of metals from coal fly ash indicated that coal organic matter has a pronounced effect on the leaching. Higher concentration of metals was extracted from virgin coal and coal fly ash at low pH (p?>?0.00) as compared to high pH. DPTA extracted metals in higher concentration from virgin coal and coal fly ash at low pH as compared to ICl. Based on the present study, the most leached metals were Fe, Cu, Mn and the least were Pb, Ni, Cd and Cr.     

Temperature and pH Dependence of Some Metals Leaching from Fly Ash of Municipal Solid Waste

Abstract. Municipal solid waste combustion leads to concentration of various metals in the solid residue (fly ash) remaining after combustion. These metals pose serious environmental hazard and require proper handling and monitoring in order to control their harmful effects. Leachability of some metals from fly ash was examined in fly ash and Milli-Q water mixture (liquid-to-solid ratio, 100) under various temperature and pH conditions in the laboratory. The leaching experiments conducted for 24 hours showed that pH was generally more important than temperature in controlling the amount of metals leached out of the fly ash. However, at a given pH, rise in temperature led to different degree of (usually one to two fold) enhanced or reduced leaching of metals. Owing to amphoteric nature of oxides of Al, Cr, Pb and Zn, these metals often yielded typical pattern of increase and decrease in their concentrations with change in pH. The extent of leaching of Cr and Pb in our experiments suggests that decrease of pH to acidic range in the case of Pb and to neutral to acidic range for Cr over a long period of storage of fly ash at solid waste dumping site may facilitate leaching of these metals from fly ash, leading to contamination of groundwater to the level that exceeds beyond the level permitted by the environmental laws.     

Sorption of As and Se on mineral components of fly ash: Relevance for leaching processes

To improve our understanding of As and Se leaching from fly ash it is necessary to know the underlying geochemical processes. It has been previously suggested that sorption processes may control the partitioning of these trace elements during leaching of fly ash. In natural systems, such as soils and sediments, As and Se have been shown to interact with iron oxides at acidic pH, with CaCO₃ at alkaline pH and with clay-minerals at neutral pH. By analogy, we compared the leaching of As and Se from fly ash with the sorption of arsenate and selenite on hematite, portlandite and mullite. It was possible to describe the leaching of As and Se from acidic fly ash with a simplified model of surface complexation with iron oxides. The apparent adsorption constants calculated from the leaching experiments resembled those calculated from our sorption experiments with hematite and values published for amorphous iron oxide. The leaching of As and Se from alkaline fly ash was compared with the sorption of arsenate and selenite on portlandite. A Ca-phase was shown to control the leaching process. Portlandite was shown to be an important sorbent for arsenate and to a lesser extent for selenite, at pH > 12.4. The affinity of arsenate and selenite for mullite was low. Maximum sorption was reached in the neutral pH ranges, similar to the interactions of oxyanions with kaolinite. Sorption reversibility of arsenate on all three minerals considered in this study was less, or at least slower, than that of selenite. This feature may partly explain that the fraction of As available for leaching from fly ash is generally lower.     

The iron-coating role on the oxidation kinetics of a pyritic sludge doped with fly ash

The present study examines the processes that control the oxidation attenuation of a pyrite-rich sludge (72 wt% pyrite) from the Iberian Pyrite Belt by the buffer capacity of a fly ash from Los Barrios power station (S Spain), using saturated column experiments. In addition, in order to understand the behaviour of both materials inside these experiments, a fly-ash leaching test and flow-through experiments with pyritic sludge were carried out. The fly-ash leaching test showed that after leaching this material with a slightly acid solution (Millipore MQ water; pH 5.6) the pH raised up to 10.2 and that the metals released by the fly-ash dissolution did not increase significantly the metal concentrations in the output solutions. The flow-through experiments with the pyritic sludge were performed at pH 9, 22 °C and O₂ partial pressure of 0.21 atm, to calculate the dissolution rate of this residue simulating the fly-ash addition. In the experiments Fe bearing oxyhydroxides precipitated as the sludge dissolved. In two non-stirred experiments the iron precipitates formed Fe-coatings on the pyrite surfaces preventing the interaction between the oxidizing agents and the pyrite grains, halting pyrite oxidation (this process is known as pyrite microencapsulation), whereas in two stirred experiments, stirring hindered the iron precipitates to coat the pyrite grains. Thus, based on the release of S (aqueous sulphate) the steady-state pyritic sludge dissolution rate obtained was 9.0 ± 0.2 × ⁻¹¹ mol m⁻² s⁻¹.In the saturated column experiments, the sludge dissolution was examined at acidic and basic pH at 22 °C and oxygen-saturated atmosphere. In a saturated column experiment filled with the pyritic sludge, pyrite oxidation occurred favourably at pH approx. 3.7. As the leachates of the fly ash yielded high basic pH, in another saturated column, consisting of an initial thick layer of fly-ash material and a layer of pyritic sludge, the pyrite dissolution took place at pH approx. 10.45. In this experiment, iron was depleted completely from the solution and attenuation of the sludge oxidation was produced in this conditions. The attenuation was likely promoted by precipitation of iron-bearing phases upon the pyritic surface forming Fe-coatings (of ferrihydrite and/or Fe(III) amorphous phases) that halted the pyrite oxidation (as in non-stirred flow-through experiments). Results suggest that buffering capacity of fly ash can be used to attenuate the pyrite-rich sludge oxidation.     

Long-term brine impacted fly ash,Part II: Mobility of major species in the ash residues

The leaching of major species from fly ash is a function of the pH of the solution in contact with the fly ash. The aim of this study was to determine the effect of the pH of the leachant on the leaching of species from the ash residues recovered after the long-term fly ash–brine interactions. Acid neutralization capacity (ANC) tests using solutions of different pH values ranging from the initial pH of the ash residues (11–12) to pH 4 were employed in the leaching experiments. The ANC tests revealed that the release of major species from the ash residues depended on the pH of the leachants except for Na and Cl, where the significant concentrations leached were independent of the solution pH. The concentrations of Al and Si in the ANC leachates were very high at pH below 6 while Ca, K, Sr, Mg and B were immediately mobilized from the brine impacted fly ash when in contact with de-ionized water, and leaching increased as the pH decreased. The concentration of SO₄ leached from the brine impacted ash residues at high pH was high, and the leaching increased with decrease in the pH of the leachant. This study shows that most of the major elements captured in the ash residues could be mobilized when in contact with aqueous solutions of various pH. This reveals that the co-disposal of fly ash and brine may not be the best practice as the major elements captured in the ash residues could leach over time.     

Leaching characteristics of fly ash

The disposal of fly ash as a byproduct of thermic power stations, results in significant environmental problems. The leaching of coal fly ash during disposal is of concern for possible contamination, especially for the aquatic environment when ash is in contact with water. The aim of this study was to investigate the leaching behaviour of fly ashes currently disposed in Kemerkoy Power Plant (Turkey) fly-ash-holding pond. The studies were conducted with fly ashes from the electrostatic precipitators (fresh fly ash) and from the fly ash pond (pre-leached fly ash). The fly ashes has alkaline in nature and pH ranges between 11.9 to 12.2. The pre-leached fly ash exhibited lower EC values (7,400 µS) than the fresh fly ash (10,300 µS). In contrast to Fe and Pb, the elements such as Cr, Cd, Cu and Co did not leach from the fly ash. The Ca and Mn concentrations decreased with increasing temperature whereas, Na and K concentrations increased. The results showed that the most important effects of fly ash leaching were pH, Na, Ca, K, Fe, Mg, Mn and Pb.     

Leachability of trace elements from two stabilized low lime Indian fly ashes

Fly ash is a waste by-product obtained from the burning of coal by thermal power plants for generating electricity. When bulk quantities are involved, in order to arrest the fugitive dust, it is stored wet rather than dry. Fly ash contains trace concentrations of heavy metals and other substances in sufficient quantities to be able to leach out over a period of time. In this study an attempt was made to study the leachabilities of a few selected trace metals: Cd, Cu, Cr, Mn, Pb and Zn from two different types of class F fly ashes. Emphasis is also laid on developing an alternative in order to arrest the relative leachabilities of heavy metals after amending them with suitable additives. A standard laboratory leaching test for combustion residues has been employed to study the leachabilities of these trace elements as a function of liquid to solid ratio and pH. The leachability tests were conducted on powdered fly ash samples before and after amending them suitably with the matrices lime and gypsum; they were compacted to their respective proctor densities and cured for periods of 28 and 180 days. A marked reduction in the relative leachabilities of the trace elements was observed to be present at the end of 28 days. These relative leachability values further reduced marginally when tests were performed at the end of 180 days.     

Changes in physical and chemical properties of three soil types in India as a result of amendment with fly ash and sewage sludge

The use of coal fly ash and domestic sewage sludge in agriculture is being considered as one of the methods for recycling of these wastes in an environmental beneficial manner. Mixtures with soil were prepared at different proportions of fly ash and sludge, either alone or in combination at a maximum application rate of 52 t ha^-1. The changes in the selected properties and heavy metal contents of three soil types in India were studied after incubating the respective mixtures for 90 days at near field capacity moisture level. Sewage sludge, due to its acidic and saline nature, high organic matter and heavy metals content, had more impact on soil properties than the fly ash. Sludge application produced several changes including an increase in available nitrogen, organic carbon, salinity and water-holding capacity of the soils. The concentrations of major cations and heavy metals also increased because of the sludge application and the pH was decreased. However, the levels of individual metal concentrations in all the mixture types were below the allowable limits prescribed by several environmental agencies. Using fly ash either alone or in equal quantity with sewage sludge had little influence on soil properties and heavy metal content. The relative availability (RA) of heavy metals in three soils amended with 52 t ha^-1 of sewage sludge was observed to be highest in oxisol, followed by alfisol and vertisol.     

Measuring reactive pools of Cd,Pb and Zn in coal fly ash from the UK using isotopic dilution assays

Large volumes of coal fly ash are continually being produced and stockpiled around the world and can be a source of environmentally sensitive trace elements. Whilst leaching tests are used for regulatory purposes, these provide little information about the true geochemical behaviour and ‘reactivity’ of trace elements in coal ash because they are poorly selective. Isotope dilution (ID) assays are frequently used in soil geochemistry as a means of measuring the reactive pools of trace metals that are in equilibrium with soil pore waters. This paper examines the applicability of multi-element ID assays in measuring the labile or reactive pool of Cd, Pb and Zn in a range of fresh and weathered fly ash, where pH is generally much more alkaline than in soils. The method generally worked well using 0.0005 M EDTA as a background electrolyte as it provided robust analytical ICP-MS measurements as well as fulfilling the important principle of ID that non-labile metal should not be solubilised. Reactive pools were equivalent to 0.5–3% of the total Pb pool and 4–13% of the total Cd pool. For Zn, where samples had pH < 11.5, the reactive Zn pool varied between 0.3% and 2%; when fresh ash samples with pH > 11.5 were tested, the method failed as the spiked isotope appeared to be sorbed or precipitated. Ash weathering was found to exert little impact on the lability of Cd, Pb and Zn. Isotope dilution results were compared with 0.43 M HNO₃ and 0.05 M EDTA extractions, these commonly being used as analogues of the ID assay, and concluded that these can be used as fast, cost-effective and simple proxies for the ID assays. Results suggest that ID methods can be used to enhance knowledge of trace element behaviour in fresh and weathered fly ash.     

Immobilization of toxic elements in mine residues derived from mining activities in the Iberian Pyrite Belt (SW Spain): Laboratory experiments

In the mining environments of the Iberian Pyrite Belt (IPB), the oxidation of sulphide wastes generates acid drainage with high concentrations of SO₄, metals and metalloids (Acid Mine Drainage, AMD). These acid and extremely contaminated discharges are drained by the fluvial courses of the Huelva province (SW Spain) which deliver high concentrations of potentially toxic elements into the Gulf of Cádiz. In this work, the oxidation process of mine tailings in the IPB, the generation of AMD and the potential use of coal combustion fly ash as a possible alkaline treatment for neutralization of and metal removal from AMD, was studied in non-saturated column experiments. The laboratory column tests were conducted on a mine residue (71.6 wt% pyrite) with artificial rainfall or irrigation. A non-saturated column filled solely with the pyrite residue leached solutions with an acid pH (approx. 2) and high concentrations of SO₄ and metals. These leachates have the same composition as typical AMD, and the oxidation process can be compared with the natural oxidation of mine tailings in the IPB. However, the application of fly ash to the same amount of mine residue in another two non-saturated columns significantly increased the pH and decreased the SO₄ and metal concentrations in the leaching solutions. The improvement in the quality of leachates by fly ash addition in the laboratory was so effective that the leachate reached the pre-potability requirements of water for human consumption under EU regulations. The extrapolation of these experiments to the field is a promising solution for the decontamination of the fluvial courses of the IPB, and therefore, the decrease of pollutant loads discharging to the Gulf of Cádiz.     

Leaching behaviour of slag and fly ash from laterite nickel ore smelting (Niquelândia,Brazil)

The laterite nickel (Ni) ore smelting operation in Niquelândia (Goiás state, Brazil) produced large amounts of smelting wastes, stockpiled on dumps (slags) and in settling ponds (fly ash). In this study we present data on the chemistry, mineralogy and pH-dependent leaching behaviours of these two waste materials.Bulk chemical analyses indicated that both wastes contained significant amounts of potentially toxic elements (PTEs), with substantially higher concentrations in the case of the fly ash (up to 2.51 wt% Ni, 1870 mg/kg Cr and 488 mg/kg Co). The mineralogical investigations carried out using X-ray diffraction analysis (XRD), scanning electron microscopy (SEM) and electron microprobe (EPMA) indicated that the slag was mainly composed of silicate glass, olivine and pyroxene. In contrast, the fly ash was composed of Ni-bearing serpentine-like phases (originating from the furnace feed), Ni-bearing glass, olivine, pyroxene and spinel. The pH-dependent leaching behaviour was performed according the EU standard experimental protocol (CEN/TS 14997) in the pH range of 3–12. The leaching was highly pH-dependent for both materials, and the highest releases of PTEs occurred at pH 3. The slag generally exhibited an U-shaped leaching behaviour of the PTEs as a function of pH, and was found to release up to 48.0 mg/kg Ni, 25.6 mg/kg Cr, and 1.42 mg/kg Co. The fly ash was significantly more reactive, and exhibited its highest leaching level of PTEs between pH 3 and 7. The maximum observed release corresponded to 5750 mg/kg Ni, 4.35 mg/kg Cr, and 112 mg/kg Co. The leached Ni concentrations after 24 h of leaching in deionized water exceeded the limit for hazardous waste by more than 100x according to the EU legislation (40 mg/kg Ni). X-ray Absorption Near Edge Structure (XANES) and Extended X-ray Absorption Fine Structures (EXAFS) spectra indicated that Ni in the fly ash is predominantly bound in a serpentine-like phase, and during the fly ash experimental alteration it was mainly released from the second shell (corresponding to the atomic distances between Ni and Si, Mg, Fe in high-temperature silicates, glass, and partially dissolved serpentine). This study shows that disposal sites for the fly ash can represent a significant source of local pollution, and direct recycling of the fly ash in the smelting technology (as currently adopted at the Barro Alto new smelter and since few years also at the Niquelândia smelter) is the best environment-friendly option for handling of fly ash in the future.     

Coal fly ash interaction with environmental fluids: Geochemical and strontium isotope results from combined column and batch leaching experiments

The major element and Sr isotope systematics and geochemistry of coal fly ash and its interactions with environmental waters were investigated using laboratory flow-through column leaching experiments (sodium carbonate, acetic acid, nitric acid) and sequential batch leaching experiments (water, acetic acid, hydrochloric acid). Column leaching of Class F fly ash samples shows rapid release of most major elements early in the leaching procedure, suggesting an association of these elements with soluble and surface bound phases. Delayed release of certain elements (e.g., Al, Fe, Si) signals gradual dissolution of more resistant silicate or glass phases as leaching continues. Strontium isotope results from both column and batch leaching experiments show a marked increase in ⁸⁷Sr/⁸⁶Sr ratio with continued leaching, yielding a total range of values from 0.7107 to 0.7138. For comparison, the isotopic composition of fluid output from a fly ash impoundment in West Virginia falls in a narrow range around 0.7124. The experimental data suggest the presence of a more resistant, highly radiogenic silicate phase that survives the combustion process and is leached after the more soluble minerals are removed. Strontium isotopic homogenization of minerals in coal does not always occur during the combustion process, despite the high temperatures encountered in the boiler. Early-released Sr tends to be isotopically uniform; thus the Sr isotopic composition of fly ash could be distinguishable from other sources and is a useful tool for quantifying the possible contribution of fly ash leaching to the total dissolved load in natural surface and ground waters.     

Comparative petrophysical and geochemical characteristics of thermal and volcanic ash from southeastern India

This paper examines the difference in the geophysical and chemical characteristic of the volcanic ash and thermal fly ash to evaluate environmental pollution. Natural volcanic ash (VA) samples from Sagirelu, Cuddapah dist., Andhra Pradesh and thermal fly ash (FA) samples from the Thermal Power Station, Ennore, Chennai, were collected, analysed and compared. The particle sizes of the ash samples were determined using the laser particle size analyzer and the different surface morphological characters were studied using SEM analyses. The chemical components such as pH, major oxides, trace metals and mineral compositions were determined using pH metre, XRF and XRD methods. pH value of the volcanic ash varies from 8.5 to 8.9 indicating its alkalinity (8.5 to 9) in volcanic ash, while the thermal ash is neutral to mildly alkaline with pH varying from 6 to 7.5. Both the ash samples have higher concentration value in SiO₂ (VA - 69.25%, FA - 46%) in major oxides and Cl (VA - 0.8%, FA - 0.1%) in trace elements. Quartz is the dominant mineral in both the types of ash, however, the volcanic ash has amorphous silica, while the fly ash contains crystalline quartz.     

Stability and leaching of cobalt smelter fly ash

The leaching behaviour of fly ash from a Co smelter situated in the Zambian Copperbelt was studied as a function of pH (5–12) using the pH-static leaching test (CEN/TS 14997). Various experimental time intervals (48 h and 168 h) were evaluated. The leaching results were combined with the ORCHESTRA modelling framework and a detailed mineralogical investigation was performed on the original FA and leached solid residues. The largest amounts of Co, Cu, Pb and Zn were leached at pH 5, generally with the lowest concentrations between pH 9 and 11 and slightly increased concentrations at pH 12. For most elements, the released concentrations were very similar after 48 h and 168 h, indicating near-equilibrium conditions in the system. Calcite, clinopyroxenes, quartz and amorphous phases predominated in the fly ash. Various metallic sulfides, alloys and the presence of Cu, Co and Zn in silicates and glass were detected using SEM/EDS and/or TEM/EDS. The leaching of metals was mainly attributed to the dissolution of metallic particles. Partial dissolution of silicate and glass fractions was assumed to significantly influence the release of Ca, Mg, Fe, K, Al and Si as well as Cu, Co and Zn. The formation of illite was suggested by the ORCHESTRA modelling to be one of the main solubility-controlling phases for major elements, whereas Co and Zn were controlled by CoO and zincite, respectively. Sorption of metals on hydrous ferric oxides was assumed to be an important attenuation mechanism, especially for the release of Pb and Cu. However, there is a high risk of Co, Cu, Pb and Zn mobility in the acidic soils around the smelter facility. Therefore, potential local options for “stabilisation” of the fly ash were evaluated on the basis of the modelling results using the PHREEQC code.     

Effect of the alkaline industrial residues fly ash,green liquor dregs,and lime mud on mine tailings oxidation when used as covering material

The potential to use the alkaline residue products fly ash, green liquor dregs, and lime mud originating from paper mills as dry cover materials to seal tailings has been investigated. Metals concentration in lime mud and fly ash had the lowest and highest contents, respectively. The tailings (<1 % sulfur content, primarily pyrite) were disposed about 50 years ago and originated from the former Rönnskär mine site in Sweden. The results of chemical composition analysis show that the raw unoxidized tailings are active toward oxidation, while the components of the adjacent oxidized tailings are not. To quantify the release of metals from the tailings and to evaluate the effect of a sealing layer on oxidation and weathering of the tailings, batch leaching tests were conducted in which leachate from alkaline residue materials was fed to the tailings. The results show that a higher concentration of most trace elements is leached from the unoxidized tailings than from the oxidized tailings. Except As and Cr, the rest of analyzed metals (Cd, Cu, Ni, Pb) became immobilized in response to the increased pH as a consequence of the amendment. The three tested alkaline amendments show a similar potential for preventing the release of metals (with the exception of As and Cr) from the tailings. Under either aerobic or anaerobic conditions, microbial activity was found to be of minor importance. XRD analysis of the field samples revealed that it was feasible to use alkaline residue products in covering tailings, and that it was advantageous to use ash as a cover material more than dregs.     

Utilization of fly ash for stabilization/solidification of heavy metal contaminated soils

Pozzolanic-based stabilization/solidification (S/S) is an effective, yet economic remediation technology to immobilize heavy metals in contaminated soils and sludges. In the present study, fly ash waste materials were used along with quicklime (CaO) to immobilize lead, trivalent and hexavalent chromium present in artificially contaminated clayey sand soils. The degree of heavy metal immobilization was evaluated using the Toxicity Characteristic Leaching Procedure (TCLP) as well as controlled extraction experiments. These leaching test results along with X-ray diffraction (XRD), scanning electron microscope and energy dispersive X-ray (SEM–EDX) analyses were also implemented to elucidate the mechanisms responsible for immobilization of the heavy metals under study. Finally, the reusability of the stabilized waste forms in construction applications was also investigated by performing unconfined compressive strength and swell tests. The experimental results suggest that the controlling mechanism for both lead and hexavalent chromium immobilization is surface adsorption, whereas for trivalent chromium it is hydroxide precipitation. Addition of quicklime and fly ash to the contaminated soils effectively reduced heavy metal leachability well below the nonhazardous regulatory limits. Overall, fly ash addition increases the immobilization pH region for all heavy metals tested, and significantly improves the stress-strain properties of the treated solids, thus allowing their reuse as readily available construction materials. The only potential problem associated with this quicklime–fly ash treatment is the excessive formation of the pozzolanic product ettringite in the presence of sulfates. Ettringite, when brought in contact with water, may cause significant swelling and subsequent deterioration of the stabilized matrix. Addition of minimum amounts of barium hydroxide was shown to effectively eliminate ettringite formation. Overall, due to the presence of very high levels of heavy metal contamination along with sulfates in the solid matrices under study, the results presented herein can be applied to the management of incinerator and coal fly ash, boiler slag and flue gas desulfurization wastes.     

Heavy metal relationships in a Pennsylvania soil

Soils of loamy sand on weathered, sandy dolomite were cored from six holes up to 70 ft beneath a municipal waste landfill in central Pennsylvania. Mn, Fe, Ni, Co, Cu, Zn, Cd, Pb, and Ag were determined in exchangeable and non-exchangeable forms in total and < 15 μm soil samples. Most of these metals were bound in Mn oxides, non-exchangeable with 0.5 M CaCl₂. The Mn oxides (often X-ray amorphous) identified when crystalline as todorokite occurred chiefly as coatings on quartz grains.Somewhat higher amounts of acid leachable trace metals were found in the < 15 μm size fraction than in the total soil samples; however, trace metal/Mn ratios were similar in both. In general, the initial mild soil leaching, which dissolved chiefly Mn oxides, gave MnFeX>Co>Ni>Pb>Zn> Cu>Cd>Ag. The final leaching, which dissolved chiefly ferric oxides, gave Fe>Mn>Ni>Zn>Co> Cu>Pb>Cd>Ag. Samples taken from an unpolluted site and from the same soils affected for seven years by leachate from the refuse had similar metal contents.Soil extractable Co, Ni, Cu, and Zn could be predicted from the Mn extracted. Based in part on factor analysis of the data, Mn-rich oxides had at least tenfold higher heavy metal percentages than Fe-rich oxides (crystalline component goethite), reflecting their greater coprecipitation potential. Because of this potential and because of the generally higher solubility of Mn than Fe oxides, more heavy metals may be released from Mn-rich than from Fe-rich soils by disposal of organic-bearing wastes. However, leaching of the moisture-unsaturated soils in situ is rarely severe enough to completely dissolve both Mn and Fe oxides. Based on the Mn content, Cd, Cu, and Pb were depleted in soil moisture beneath the landfill relative to their amounts in the soil. This depletion may reflect factors including heterogeneity in metal content of the soil oxides; preferential resorption of these metals; and removal of the Cd, Cu, and Pb as organic precipitates or as inorganic precipitates such as carbonates.     

pH influence on sorption characteristics of heavy metal in the vadose zone

Sorption is an important process in the modelling and prediction of the movement of heavy metals in unsaturated clay barriers. This experimental study investigates the effect of pH changes in the acidic range on the sorption characteristics of heavy metals such as: lead, copper and zinc in an unsaturated soil. A series of one-dimensional coupled solute and moisture leaching column tests, using different heavy metal solutions, were conducted on an unsaturated illitic soil at varying pH values. Variations of volumetric water content (VWC) with distance were measured for different time durations, and concentrations of heavy metals in the liquid and solid phases were analysed. Partitioning coefficient profiles of contaminants along the soil column were determined for each individual layer in the soil.

Results from column leaching tests showed that the sorption characteristics of heavy metals are controlled by many factors which should be taken into consideration, i.e. the VWC, time of wetting, soil pH, and the influent heavy metal concentrations. Simplification of K_d as a constant and of the VWC as a linear function cannot be considered a good assumption and may lead to an improper evaluation of the sorption phenomena and also to serious errors in predicting contaminant transport through unsaturated soils.     

Feasibility of using fly ash,lime, and bentonite to neutralize acidity of pore fluids

Acidic groundwater resulting from the poorly planned use of acid sulfate soils has become a major environmental issue in coastal Australia over the last several years. Use of permeable reactive barriers (PRBs) designed to generate alkalinity by promoting sulfate reduction has recently become popular as an alternative solution to this problem. However, recent studies have also revealed that the long-term performance of such PRBs can be significantly undermined by chemical precipitation and clogging of pore space, which would decrease the buffer capacity and hydraulic conductivity of the reactive material. This study seeks to explore the feasibility of using bentonite in addition to lime and fly ash to form mixtures with a high buffer capacity and permeability that would enable groundwater flow through PRBs over a substantial period of time. A series of laboratory experiments, including buffer capacity and leaching tests, were performed on different mixtures of fly ash with lime and bentonite using acidic fluids of low pH. It was found that the ability of such mixtures to neutralize acidic fluids was mostly controlled by the content of lime. Laboratory data also showed that an addition of bentonite to lime—fly ash mixtures could decrease the buffer capacity of soil. Compaction tests indicated that the presence of bentonite would increase the dry density of mixtures at the optimum moisture content. A series of hydraulic conductivity tests were carried out to study changes in the coefficient of permeability of lime—fly ash mixtures with different contents of bentonite permeated with acidic liquids. The obtained results revealed that the coefficient of permeability of the specimens tended to increase over a period of time, likely due to the changes in the diffuse double layer of bentonite particles.     

粉煤灰污泥添加剂对地下水质影响的模拟研究

通过测定土柱和淋洗液中重金属的含量,研究石灰岩质土壤应用粉煤灰污泥添加剂改良后重金属在土壤剖面上的分布移动特征及对地下水质的影响.结果表明:仅试验层内除As和Ni外,Zn、Cd、Pb、Cu、Cr、Hg含量明显增加,未出现明显向下移动的趋势;同时重金属淋出量明显增加,但未超过地下水Ⅲ级标准.初步认为与添加剂自身、重金属的特性及石灰岩质土壤滤层的截固作用相关.粉煤灰污泥经过合理的配施和预处理应用于石灰岩质矿区退化土壤的改良,短期内不会对地下水的质量产生明显的影响.