Structural systematics of Ge substitution in primitive pyroxenes

Pyroxenes of general stoichiometry Mg(Ge _x Si_1?x )O₃ were encountered in attempts to synthesise Ge-substituted talcs at 0.2 GPa, 650–700 °C. Orthopyroxenes (Pbca) of compositions x = 0.21, 0.30, and 0.34 were identified, and also a P2₁/c clinopyroxene of composition x = 0.63, and C2/c clinopyroxenes of compositions x = 0.91 and 1. End-member clinoenstatite MgSiO₃-P2₁/c synthesised at 16 GPa, 1300 °C and transformed from C2/c was also included in the study. Crystal structure refinements using single-crystal XRD data showed that unit-cell parameters vary linearly with Si–Ge for the Pbca and P2₁/c pyroxenes, both of which have two symmetrically non-equivalent tetrahedral chains. Refinement of Si–Ge occupancies at tetrahedral sites showed that the two chains of all primitive pyroxenes have very different compositions, with X_Ge(TB) ? X_Ge(TA). This difference arises from the greater flexibility of the B-chain to rotate in response to tetrahedral expansion due to increasing Ge content. The TA-M2 shared polyhedral edge imposes significant constraints on the flexibility of the A-chain, which can accommodate much less Ge than the B-chain. Linear trends of cell parameters, site occupancies, and structural parameters for the primitive pyroxenes, when extrapolated to published data for MgGeO₃–Pbca, extend across the entire Si–Ge join.     

Chromium solubility in anhydrous Phase B

The crystal structure and chemical composition of a crystal of (Mg_14?x Cr _x )(Si_5?x Cr _x )O₂₄ (x ≈ 0.30) anhydrous Phase B (Anh-B) synthesized in the model system MgCr₂O₄–Mg₂SiO₄ at 12 GPa and 1600 °C have been investigated. The compound was found to be orthorhombic, space group Pmcb, with lattice parameters a = 5.900(1), b = 14.218(2), c = 10.029(2) Å, V = 841.3(2) Å³ and Z = 2. The structure was refined to R ₁ = 0.065 using 1492 independent reflections. Chromium was found to substitute for both Mg at the M3 site (with a mean bond distance of 2.145 Å) and Si at the octahedral Si1 site (mean bond distance: 1.856 Å), according to the reaction Mg²⁺ + Si⁴⁺ = 2Cr³⁺. Such substitutions cause a reduction in the volume of the M3 site and an increase in the volume of the Si-dominant octahedron with respect to the values typically observed for pure Anh-B and Fe²⁺-bearing Anh-B. Taking into account that Cr³⁺ is not expected to be Jahn–Teller active, it appears that both the Cr³⁺–for–Mg and Cr³⁺–for–Si substitutions in the Anh-B structure decrease the distortion of the octahedra. Electron microprobe analysis gave the Mg_13.66(8)Si_4.70(6)Cr_0.62(4)O₂₄ stoichiometry for the studied phase. The successful synthesis of this phase provides new information for the possible mineral assemblages occurring in the Earth’s deep upper mantle and shed new light on the so-called X discontinuity that has been observed at 275–345 km depth in several subcontinental and subduction zone environments.     

Mineralogy and metasomatic evolution of the Mianeh iron skarn deposit,Norduz-Agarak border,NW Iran

The Mianeh iron skarn deposit lies in the Arasbaran region within the Qaradagh metallogenic district, NW Iran. This high-grade massive magnetite skarn originated by the interaction of Upper Cretaceous limestone with metasomatic ore-bearing fluids associated with hypabyssal Oligo-Miocene quartz diorite. Mineral chemistry of the primary clinopyroxenes demonstrates the sub-alkaline, volcanic arc setting of magmatism. Two general stages of skarnification are recognized: (1) silicate skarn (stage I) is composed essentially of grossular and low-Fe diopside formed before the main mineralization and (2) magnetite-garnet skarn (stage II) composed of strongly anisotropic coarse-grained garnets with a narrow compositional zoning radially formed by addictive infiltrating of silica and iron-rich metasomatic fluids which overprint and/or crosscut the early stage silicate skarn. Anhydrous prograde calc-silicate assemblages were replaced by a series of hydrous calc-silicates (epidote, tremolite-actinolite) and/or quartz, calcite, magnetite, hematite, and pyrite. Magnetite (±hematite) is the dominant hypogene ore mineral that initially precipitated coincident with the late prograde to the early retrograde metasomatic stages. Mineralogical studies suggest that silicate skarn formation commenced at temperatures about 560 °C, X(CO₂)_fluid ≤ 0.15, αSiO₂～?1.0, and fluid pressure 1.0 kbar. The magnetite-garnet skarn formed from H₂O-rich fluids [X(CO₂)_fluid < 0.1] at a temperature of 525 to 450 °C and maximum log ?O₂ between ?20.2 and ?23. During the late stages of prograde skarn development, the stability field of andradite shifted to low ?O₂ and ?S₂ conditions resulting in main iron ore deposition (as magnetite). The andradite replacement temperature and presence of pyrite (instead of pyrrhotite) suggest that log?S₂ remained constant at about ?6 to ?7 during cooling of the system.     

Spectroscopic studies of synthetic and natural ringwoodite, γ-(Mg,Fe)<Subscript>2</Subscript>SiO<Subscript>4</Subscript>

Synthetic ringwoodite γ-(Mg_1?x Fe _x )₂SiO₄ of 0.4 ≤ x ≤ 1.0 compositions and variously colored micro-grains of natural ringwoodite in shock metamorphism veins of thin sections of two S6-type chondrites were studied by means of microprobe analysis, TEM and optical absorption spectroscopy. Three synthetic samples were studied in addition with Mössbauer spectroscopy. The Mössbauer spectra consist of two doublets caused by ^VIFe²⁺ and ^VIFe³⁺, with IS and QS parameters close to those established elsewhere (e.g., O’Neill et al. in Am Mineral 78:456–460, 1993). The Fe³⁺/Fe_total ratio evaluated by curve resolution of the spectra, ranges from 0.04 to 0.1. Optical absorption spectra of all synthetic samples studied are qualitatively very similar as they are directly related to the iron content. They differ mostly in the intensity of the observed absorption features. The spectra consist of a very strong high-energy absorption edge and a series of absorption bands of different width and intensity. The three strongest and broadest absorptions of them are attributed to splitting of electronic spin-allowed ⁵ T _2g → ⁵ E _g transitions of ^VIFe²⁺ and intervalence charge-transfer (IVCT) transition between ferrous and ferric ions in adjacent octahedral sites of the ringwoodite structure. The spin-allowed bands at ca. 8,000 and 11,500 cm^?1 weakly depend on temperature, whilst the Fe²⁺/Fe³⁺ IVCT band at ~16,400 cm^?1 displays very strong temperature dependence: i.e., with increasing temperature it decreases and practically disappears at about 497 K, a behavior typical for bands of this type. With increasing pressure the absorption edge shifts to lower energies while the spin-allowed bands shift to higher energy and strongly decreases in intensity. The IVCT band also strongly weakens and vanishes at about 9 GPa. We assigned this effect to pressure-induced reduction of Fe³⁺ in ringwoodite. By analogy with synthetic samples three broad bands in spectra of natural (meteoritic) blue ringwoodite are assigned to electronic spin-allowed transitions of ^VIFe²⁺ (the bands at ~8,600 and ~12,700 cm^?1) and Fe²⁺/Fe³⁺ IVCT transition (~18,100 cm^?1), respectively. Spectra of colorless ringwoodite of the same composition consist of a single broad band at ca. 12,000 cm^?1. It is assumed that such ringwoodite grains are inverse (Fe, Mg)₂SiO₄-spinels and that the single band is caused by the split spin-allowed ⁵ E → ⁵ T ₂ transition of ^IVFe²⁺. Ringwoodite of intermediate color variations between dark-blue and colorless are assumed to be partly inversed ringwoodite. No glassy material between the grain boundaries in the natural colored ringwoodite aggregates was found in our samples and disprove the cause of the coloration to be due to light scattering effect (Lingemann and Stöffler in Lunar Planet Sci 29(1308), 1998).     

Crystallochemical effects of heat treatment on Fe-dominant tourmalines from Dolní Bory (Czech Republic) and Vlachovo (Slovakia)

Heat treatment was performed on selected Fe-dominant tourmalines to establish the nature of any change in optical properties. Two tourmaline samples from Dolní Bory, Czech Republic (TDB) and Vlachovo, Slovakia (TVL) were heated at 450, 700 and 900°C at 0.1 mPa and ambient oxidation conditions for 8 h. EMPA study shows that tourmaline from Vlachovo has schorlitic composition and tourmaline from Dolní Bory is alkali-depleted schorl to foitite. Although the black colour remained unchanged after heating at 450°C, it changed to brown at 700°C and reddish brown at 900°C. No significant changes of chemical composition were observed during heating. X-ray diffraction, infrared and Mössbauer study showed negligible oxidation of tourmaline heated at 450°C, but a significant change in iron valency state and deprotonization at 700°C. The oxidation of Fe is the main cause of tourmaline colour change, and the substitution vector for oxidation of Fe is Fe³⁺OFe _?1 ²⁺ (OH)_?1. The predicted deprotonization of OH was confirmed by infrared spectroscopy, which documented a decrease in OH groups in both samples, mainly at the V site. The oxidation of Fe is mostly significant in the Y site as documented on the compression of the Y-site octahedra and subsequent decrease in the a lattice parameter. This feature is consistent with lattice dimensions in the transition from schorl and foitite dimensions to those consistent with fluor-buergerite. The Z-site octahedra did not compressed and were not affected by heating-induced Fe oxidation, which indicates only negligible content of ^Z Fe²⁺ in original samples. After heating at 900°C, the tourmaline structure collapsed likely due to the thermally induced weakening of bonds in Y and Z octahedra, which results in amorphization of tourmaline. Subsequently, breakdown products including Fe-oxides and mullite replaced alkali-depleted amorphized tourmaline.     

Influence of oxygen fugacity and temperature on the redox state of iron in natural silicic aluminosilicate melts

The influence of oxygen fugacity (fO₂) and temperature on the valence and structural state of iron was experimentally studied in glasses quenched from natural aluminosilicate melts of granite and pantellerite compositions exposed to various T-fO₂ conditions (1100–1420°C and 10^?12–10^?0.68 bar) at a total pressure of 1 atm. The quenched glasses were investigated by Mössbauer spectroscopy. It was shown that the effect of oxygen fugacity on the redox state of iron at 1320–1420°C can be described by the equation log(Fe³⁺/Fe²⁺) = k log(fO₂) + q, where k and q are constants depending on melt composition and temperature. The Fe³⁺/Fe²⁺ ratio decreases with decreasing fO₂ (T = const) and increasing temperature (fO₂ = const). The structural state of Fe³⁺ depends on the degree of iron oxidation. With increasing Fe³⁺/Fe²⁺ ≥ 1, the dominant coordination of Fe³⁺ changes from octahedral to tetrahedral. Ferrous iron ions occur in octahedral (and/or five-coordinated) sites independent of Fe³⁺/Fe²⁺.     

Elastic behavior of vanadinite,Pb<Subscript>10</Subscript>(VO<Subscript>4</Subscript>)<Subscript>6</Subscript>Cl<Subscript>2</Subscript>, a microporous non-zeolitic mineral

The high-pressure behavior of a vanadinite (Pb₁₀(VO₄)₆Cl₂, a = b = 10.3254(5), c = 7.3450(4) Å, space group P6₃/m), a natural microporous mineral, has been investigated using in-situ HP-synchrotron X-ray powder diffraction up to 7.67 GPa with a diamond anvil cell under hydrostatic conditions. No phase transition has been observed within the pressure range investigated. Axial and volume isothermal Equations of State (EoS) of vanadinite were determined. Fitting the P–V data with a third-order Birch-Murnaghan (BM) EoS, using the data weighted by the uncertainties in P and V, we obtained: V ₀ = 681(1) Å³, K ₀ = 41(5) GPa, and K′ = 12.5(2.5). The evolution of the lattice constants with P shows a strong anisotropic compression pattern. The axial bulk moduli were calculated with a third-order “linearized” BM-EoS. The EoS parameters are: a ₀ = 10.3302(2) Å, K ₀(a) = 35(2) GPa and K′(a) = 10(1) for the a-axis; c ₀ = 7.3520(3) Å, K ₀(c) = 98(4) GPa, and K′(c) = 9(2) for the c-axis (K ₀(a):K ₀(c) = 1:2.80). Axial and volume Eulerian-finite strain (fe) at different normalized stress (Fe) were calculated. The weighted linear regression through the data points yields the following intercept values: Fe _a (0) = 35(2) GPa for the a-axis, Fe _c (0) = 98(4) GPa for the c-axis and Fe _V (0) = 45(2) GPa for the unit-cell volume. The slope of the regression lines gives rise to K′ values of 10(1) for the a-axis, 9(2) for the c-axis and 11(1) for the unit cell-volume. A comparison between the HP-elastic response of vanadinite and the iso-structural apatite is carried out. The possible reasons of the elastic anisotropy are discussed.     

High-pressure behavior of natural single-crystal epidote and clinozoisite up to 40 GPa

The comparative compressibility and high-pressure stability of a natural epidote (0.79 Fe-total per formula unit, Fe_tot pfu) and clinozoisite (0.40 Fe_tot pfu) were investigated by single-crystal X-ray diffraction and Raman spectroscopy. The lattice parameters of both phases exhibit continuous compression behavior up to 30 GPa without evidence of phase transformation. Pressure–volume data for both phases were fitted to a third-order Birch–Murnaghan equation of state with V ₀ = 461.1(1) ų, K ₀ = 115(2) GPa, and \(K_{0}^{'}\) = 3.7(2) for epidote and V ₀ = 457.8(1) ų, K ₀ = 142(3) GPa, and \(K_{0}^{'}\) = 5.2(4) for clinozoisite. In both epidote and clinozoisite, the b-axis is the stiffest direction, and the ratios of axial compressibility are 1.19:1.00:1.15 for epidote and 1.82:1.00:1.19 for clinozoisite. Whereas the compressibility of the a-axis is nearly the same for both phases, the b- and c-axes of the epidote are about 1.5 times more compressible than in clinozoisite, consistent with epidote having a lower bulk modulus. Raman spectra collected up to 40.4 GPa also show no indication of phase transformation and were used to obtain mode Grüneisen parameters (γ _i) for Si–O vibrations, which were found to be 0.5–0.8, typical for hydrous silicate minerals. The average pressure coefficient of Raman frequency shifts for M–O modes in epidote, 2.61(6) cm^?1/GPa, is larger than found for clinozoisite, 2.40(6) cm^?1/GPa, mainly due to the different compressibility of FeO₆ and AlO₆ octahedra in M3 sites. Epidote and clinozoisite contain about 2 wt% H₂O are thus potentially important carriers of water in subducted slabs.     

A modified normalized model for predicting effective soil thermal conductivity

Effective soil thermal conductivity (λ _eff) describes the ability of a multiphase soil to transmit heat by conduction under unit temperature gradient. It is a critical parameter for environmental science, earth and planetary science, and engineering applications. Numerous models are available in the literature, but their applicability is generally restricted to certain soil types or water contents (θ). The objective of this study was to develop a new model in the similar form of the Johansen 1975 model to simulate the λ _eff(θ) relationship of soils of various soil textures and water contents. An exponential type model with two parameters is developed and a new function for calculating dry soil thermal conductivity is presented. Performance of the new model and six other normalized models were evaluated with published datasets. The results show that the new model is able to well mimic λ _eff(θ) relationship of soils from sand to silt loam and from oven dry to full saturation. In addition, it has the best performance among the seven models under test (with root-mean-square error of 0.059 W m^?1 °C^?1, average deviations of 0.0009 W m^?1 °C^?1, and Nash–Sutcliffe efficiency of 0.994). The new model has potential to improve the reliability of soil thermal conductivity estimation and be incorporated into numerical modeling for environmental, earth and engineering studies.     

The stress regime in a Rotliegend reservoir of the Northeast German Basin

In-situ stresses have significant impact, either positive or negative, on the short and long term behaviour of fractured reservoirs. The knowledge of the stress conditions are therefore important for planning and utilization of man-made geothermal reservoirs. The geothermal field Groß Schönebeck (40 km north of Berlin/Germany) belongs to the key sites in the northeastern German Basin. We present a stress state determination for this Lower Permian (Rotliegend) reservoir by an integrated approach of 3D structural modelling, 3D fault mapping, stress ratio definition based on frictional constraints, and slip-tendency analysis. The results indicate stress ratios of the minimum horizontal stress S _hmin being equal or increasing 0.55 times the amount of the vertical stress S _V (S _hmin ≥ 0.55S _V ) and of the maximum horizontal stress S _Hmax ≤ 0.78–1.00S _V in stress regimes from normal to strike slip faulting. Thus, acting stresses in the 4,100-m deep reservoir are S _V  = 100 MPa, S _hmin = 55 MPa and S _Hmax = 78?100 MPa. Values from hydraulic fracturing support these results. Various fault sets of the reservoir are characterized in terms of their potential to conduct geothermal fluids based on their slip and dilatation tendency. This combined approach can be adopted to any other geothermal site investigation.     

Electron paramagnetic resonance studies on clinochlore from Longitudinal Valley area,northeastern Taiwan

A natural sample of clinochlore from the Longitudinal Valley area of northeastern Taiwan has been characterized by using the powder X-ray diffraction (XRD), differential thermal analysis and electron paramagnetic resonance (EPR) spectroscopic techniques. The lattice parameters of the monoclinic (IIb) clinochlore with the composition (Mg_2.988 Al_1.196 Fe_1.6845 Mn_0.026)_5.8945 (Si_2.559 Al_1.441)₄ O₁₀ (OH)₈ have been calculated from the powder XRD data and are found to be a = 5.347 Å, b = 9.223 Å, c = 14.250 Å, β = 97.2° and Z = 2. The thermal behaviour of the sample showed the typical behaviour of clinochlore with a hydroxyl content of 12.5 wt%. The EPR spectrum at room temperature exhibits two resonance signals centred at g ≈ 2.0 and g ≈ 8.0. The signal at g ≈ 2.0 shows a six-line hyperfine structure which is a characteristic of Mn²⁺ ions in octahedral symmetry. The resonance signal at g ≈ 8.0 is a characteristic of Fe³⁺ ions. The EPR spectra have also been recorded at different temperatures (123–295 K). The population of spin levels (N) has been calculated for g ≈ 2.0 and g ≈ 8.0 resonance signals. It is observed that N increases with decreasing temperature. From EPR spectra, the spin-Hamiltonian parameters have been evaluated. The zero-field splitting parameter (D) is found to be temperature dependent. The peak-to-peak width of the g ≈ 8.0 resonance signal is found to increase with decrease in temperature.     

High-pressure phase transitions of CaRhO<Subscript>3</Subscript> perovskite

High-pressure phase transitions of CaRhO₃ perovskite were examined at pressures of 6–27 GPa and temperatures of 1,000–1,930°C, using a multi-anvil apparatus. The results indicate that CaRhO₃ perovskite successively transforms to two new high-pressure phases with increasing pressure. Rietveld analysis of powder X-ray diffraction data indicated that, in the two new phases, the phase stable at higher pressure possesses the CaIrO₃-type post-perovskite structure (space group Cmcm) with lattice parameters: a = 3.1013(1) Å, b = 9.8555(2) Å, c = 7.2643(1) Å, V _m  = 33.43(1) cm³/mol. The Rietveld analysis also indicated that CaRhO₃ perovskite has the GdFeO₃-type structure (space group Pnma) with lattice parameters: a = 5.5631(1) Å, b = 7.6308(1) Å, c = 5.3267(1) Å, V _m  = 34.04(1) cm³/mol. The third phase stable in the intermediate P, T conditions between perovskite and post-perovskite has monoclinic symmetry with the cell parameters: a = 12.490(3) Å, b = 3.1233(3) Å, c = 8.8630(7) Å, β = 103.96(1)°, V _m  = 33.66(1) cm³/mol (Z = 6). Molar volume changes from perovskite to the intermediate phase and from the intermediate phase to post-perovskite are –1.1 and –0.7%, respectively. The equilibrium phase relations determined indicate that the boundary slopes are large positive values: 29 ± 2 MPa/K for the perovskite—intermediate phase transition and 62 ± 6 MPa/K for the intermediate phase—post-perovskite transition. The structural features of the CaRhO₃ intermediate phase suggest that the phase has edge-sharing RhO₆ octahedra and may have an intermediate structure between perovskite and post-perovskite.     

Surface irrigation performance of date palms under water scarcity in arid irrigated lands

In this paper, a study on the performance of surface irrigation of date palms in a Tunisian arid area (Douz oasis) is presented. The study is conducted in 16 plots with various sizes and soil textures over a 4-year period (2012–2015). In the first step, an assessment of total water requirements of the date palms is carried out. Then, the surface irrigation performance is analyzed using three indicators, i.e., the relative water supply (RWS) indicator, the uniformity index of water distribution (D _U ), and the water application efficiency (E _a ). Finally, the irrigation management problems are identified. The results indicate that in the arid Tunisian Saharan oases, the soil texture, plot size, and farmers’ practices (especially irrigation duration) have significant effects on surface irrigation performance. The average annual net irrigation requirements of date palms are about 2400 mm. The RWS increases from 1.8 in the smaller plots (0.5 ha) to 3.6 in the largest plots (2.5 ha), implying that the increase in the plot size requires an excessive water supply. D _U decreases from 80.7 in the 0.5 ha plots to 65.4 in the 2.5 ha plots; however, no significant difference in the E _a is observed. The results show that the soil texture has no influence on the RWS and D _U , but the E _a is significantly higher in the loamy-sand soils (46.7%) compared to the sandy soils (36.3%). Overall, RWS indicator is higher than 1 (RWS?=?2.6) implying excessive irrigation supply to the system. Although D _U is relatively uniform (>?60%), E _a is relatively low (<?50%) indicating that the current irrigation management is inefficient. These findings have a paramount importance for improving irrigation water management in the Tunisian Saharan oases.     

Structural investigations of (Ca,Sr)ZrO<Subscript>3</Subscript> and Ca(Sn,Zr)O<Subscript>3</Subscript> perovskite compounds

(Ca _x ,Sr_1?x )ZrO₃ and Ca(Sn _y ,Zr_1-y )O₃ solid solutions were synthesized by solid-state reaction at high temperature before to be studied by powder X-ray diffraction and Raman Spectroscopy. Diffraction data allow the distortion of the ABO₃ perovskite structure to be investigated according to cations substitution on A and B-sites. It is shown that distortion, characterized by Φ, the tilt angle of BO₆ octahedra, slightly increases with decreasing y content in Ca(Sn _y ,Zr_1?y )O₃ compounds and strongly decreases with decreasing x content in (Ca _x ,Sr_1?x )ZrO₃ compounds. Such results are discussed in view of the relative A and B cation sizes. Raman data show that vibrational spectra are strongly affected by the cation substitution on A-site; the frequencies of most vibrational modes increase with increasing x content in (Ca _x ,Sr_1?x )ZrO₃ compounds, i.e. with the decreasing mean size of the A-cation; the upper shift is observed for the 358 cm^?1 mode (?ν/?r = ?60.1 cm^?1/Å). On the other hand, the cation substitution on B-sites, slightly affect the spectra; it is shown that in most cases, the frequency of vibrational modes increases with increasing y content in Ca(Sn _y ,Zr_1?y )O₃ compounds, i.e. with the decreasing mean size of the B-cation, but that two modes (287 and 358 cm^?1) behave differently: their frequencies decrease with the decreasing mean size of the B-cation, with a shift respectively equal to +314 and +162 cm^?1/Å. Such results could be used to predict the location of different elements such as trivalent cations or radwaste elements on A- or B-site, in the perovskite structure.     

The Influence of Benthic Macrofauna on the Erodibility of Intertidal Sediments with Varying mud Content in Three New Zealand Estuaries

Fine sediment inputs can alter estuarine ecosystem structure and function. However, natural variations in the processes that regulate sediment transport make it difficult to predict their fate. In this study, sediments were sampled at different times (2011–2012) from 45 points across intertidal sandflat transects in three New Zealand estuaries (Whitford, Whangamata, and Kawhia) encompassing a wide range in mud (≤63 μm) content (0–56 %) and macrofaunal community structure. Using a core-based erosion measurement device (EROMES), we calculated three distinct measures of sediment erosion potential: erosion threshold (? _c ; N m^?2), erosion rate (ER; g m^?2 s^?1), and change in erosion rate with increasing bed shear stress (m _e ; g N^?1 s^?1). Collectively, these measures characterized surface (? _c and ER) and sub-surface (m _e ) erosion. Benthic macrofauna were grouped by functional traits (size and motility) and data pooled across estuaries to determine relationships between abiotic (mud content, mean grain size) and biotic (benthic macrofauna, microbial biomass) variables and erosion measures. Results indicated that small bioturbating macrofauna (predominantly freely motile species <5 mm in size) destabilized surface sediments, explaining 23 % of the variation in ? _c (p ≤ 0.01) and 59 % of the variation in ER (p ≤ 0.01). Alternatively, mud content and mean grain size cumulatively explained 61 % of the variation in m _e (p ≤ 0.01), where increasing mud and grain size stabilized sub-surface sediments. These results highlight that the importance of biotic and abiotic predictors vary with erosion stage and that functional group classifications are a useful way to determine the impact of benthic macrofauna on sediment erodibility across communities with different species composition.     

Single-crystal X-ray diffraction and spectroscopic studies on humboldtine and lindbergite: weak Jahn–Teller effect of Fe<Superscript>2+</Superscript> ion

The single-crystal of humboldtine [Fe²⁺(C₂O₄) · 2H₂O] was first synthesized and the crystal structure has been refined. Single-crystal X-ray diffraction data were collected using an imaging-plate diffractometer system and graphite-monochromatized MoKα radiation. The crystal structure of humboldtine was refined to an agreement index (R1) of 3.22% calculated for 595 unique observed reflections. The mineral crystallizes in the monoclinic system, space group C2/c, with unit cell dimensions of a = 12.011 (11), b = 5.557 (5), c = 9.920 (9) Å, β = 128.53 (3)?, V = 518.0 (8) Å³, and Z = 4. In this crystal structure, the alternation of oxalate anions [(C₂O₄)^2?] and Fe²⁺ ions forms one-dimensional chain structure parallel to [010]; water molecules (H₂O)⁰ create hydrogen bonds to link the chains, where (H₂O)⁰ is essentially part of the crystal structure. The water molecules with the two lone electron pairs (LEPs) on their oxygen atom are tied obliquely to the chains, because the one lone electron pair is considered to participate in the chemical bonds with Fe²⁺ ions. Humboldtine including hydrogen bonds is isotypic with lindbergite [Mn²⁺(C₂O₄) · 2H₂O]. The donor–acceptor separations of the hydrogen bonds in humboldtine are slightly shorter than those in lindbergite, which suggests that the hydrogen bonds in the former are stronger than those in the latter. The infrared and Raman spectra of single-crystals of humboldtine and lindbergite confirmed the differences in hydrogen-bond geometry. In addition, Fe²⁺–O stretching band of humboldtine was split and broadened in the observed Raman spectrum, owing to the Jahn–Teller effect of Fe²⁺ ion. These interpretations were also discussed in terms of bond-valence theory.     

Effect of 2-D Random Field Discretization on Failure Probability and Failure Mechanism in Probabilistic Slope Stability

This paper investigates, using the random field theory and Monte Carlo simulation, the effects of random field discretization on failure probability, p _f, and failure mechanism of cohesive soil slope stability. The spatial sizes of the discretized elements in random field Δx, Δy in horizontal and vertical directions, respectively, are assigned a series of combinational values in order to model the discretization accuracy. The p _f of deterministic critical slip surface (DCSS) and that of the slope system both are analyzed. The numerical simulation results have demonstrated that both the ratios of Δy/λ _y (λ _y  = scale of fluctuation in vertical direction) and Δx/λ _x (λ _x  = scale of fluctuation in horizontal direction) contribute in a similar manner to the accuracy of p _f of DCSS. The effect of random field discretization on the p _f can be negligible if both the ratios of Δx/λ _x and Δy/λ _y are no greater than 0.1. The normalized discrepancy tends to increase at a linear rate with Δy/λ _y when Δx/λ _x is larger than 0.1, and vice versa for p _f of DCSS. The random field discretization tends to have more considerable influence on the p _f of DCSS than on that of the slope system. The variation of p _f versus λ _x and λ _y may exhibit opposite trends for the cases where the limit state functions of slope failure are defined on DCSS and on the slope system as well. Finally, the p _f of slope system converges in a more rapid manner to that of DCSS than the failure mechanism does to DCSS as the spatial variability of soil property grows from significant to negligible.     

Efficient removal of Evans blue dye by Zn–Al–NO<Subscript>3</Subscript> layered double hydroxide

Evans blue (EB) dye has been successfully removed from aqueous solution through chemisorption process with synthetic layered double hydroxides (LDH) [Zn_1?x Al _x (OH)₂NO₃·nH₂O, x = 0.2–0.33]. Detailed evaluation of dye adsorption characteristics in aqueous medium has been studied for different layer charged hydroxides. The objective of the study was efficient removal of a dye by LDH and understanding the structure–property relationship of the LDH on its adsorption behaviour. Highest Langmuir monolayer adsorption capacity (Qt) of 113.64 mg g^?1 was observed for highest layer charge x = 0.33, and it is higher than previously reported values for the LDH-EB dye system. Under optimized condition, 99% of EB dye is removed from aqueous solution within 60 min at 313 K. The monotonous increase in Qt value with increasing layer charge is correlated with layer charge density (LCD) and lower particle size of the synthetic LDH. The variation in Qt among different layer charged materials is marginal (3.46–4.17%) with respect to the respective anion exchange capacity (AEC) of LDH NO₃. The limited contribution of AEC surmises the occurrence of surface-only adsorption and absence of intercalation as validated by the XRD analysis. The spontaneity of the EB dye removal increases with increasing temperature and LCD. The chemisorption nature of the adsorption reaction is well supported by the thermodynamics values.     

Properties of the aftershocks sequences of the 2000 and 2002 earthquakes in Aksehir-Afyon graben,west-central Anatolia,Turkey

The b-value of the Gutenberg–Richter’s frequency–magnitude relation and the p-value of the modified Omori law, which describes the decay rate of aftershock activity, were investigated for more than 500 aftershocks in the Aksehir-Afyon graben (AAG) following the 15 December 2000 Sultandagi–Aksehir and the 3 February 2002 Çay–Eber and Çobanlar earthquakes. We used the Kandilli Observatory’s catalog, which contains records of aftershocks with magnitudes ≥2.5. For the Çobanlar earthquake, the estimated b-values for three aftershock sequences are in the range 0.34 ≤  b ≤ 2.85, with the exception of the one that occurred during the first hour (4.77), while the obtained p-values are in the range 0.44 ≤ p ≤ 1.77. The aftershocks of the Sultandagi earthquake have a high p-value, indicating fast decay of the aftershock activity. A regular increase of b can be observed, with b < 1.0 after 0.208 days for the Çay–Eber earthquake. A systematic and similar increase and decrease pattern exists for the b- and p-values of the Çobanlar earthquakes during the first 5 days.