Experimental determination of magnesia and silica solubilities in graphite-saturated and redox-buffered high-pressure COH fluids in equilibrium with forsterite + enstatite and magnesite + enstatite

We experimentally investigated the dissolution of forsterite, enstatite and magnesite in graphite-saturated COH fluids, synthesized using a rocking piston cylinder apparatus at pressures from 1.0 to 2.1 GPa and temperatures from 700 to 1200 °C. Synthetic forsterite, enstatite, and nearly pure natural magnesite were used as starting materials. Redox conditions were buffered by Ni–NiO–H₂O (ΔFMQ = ??0.21 to ??1.01), employing a double-capsule setting. Fluids, binary H₂O–CO₂ mixtures at the P, T, and fO₂ conditions investigated, were generated from graphite, oxalic acid anhydrous (H₂C₂O₄) and water. Their dissolved solute loads were analyzed through an improved version of the cryogenic technique, which takes into account the complexities associated with the presence of CO₂-bearing fluids. The experimental data show that forsterite?+?enstatite solubility in H₂O–CO₂ fluids is higher compared to pure water, both in terms of dissolved silica (mSiO₂?=?1.24 mol/kg_H2O versus mSiO₂?=?0.22 mol/kg_H2O at P?=?1 GPa, T?=?800 °C) and magnesia (mMgO?=?1.08 mol/kg_H2O versus mMgO?=?0.28 mol/kg_H2O) probably due to the formation of organic C–Mg–Si complexes. Our experimental results show that at low temperature conditions, a graphite-saturated H₂O–CO₂ fluid interacting with a simplified model mantle composition, characterized by low MgO/SiO₂ ratios, would lead to the formation of significant amounts of enstatite if solute concentrations are equal, while at higher temperatures these fluid, characterized by MgO/SiO₂ ratios comparable with that of olivine, would be less effective in metasomatizing the surrounding rocks. However, the molality of COH fluids increases with pressure and temperature, and quintuplicates with respect to the carbon-free aqueous fluids. Therefore, the amount of fluid required to metasomatize the mantle decreases in the presence of carbon at high P–T conditions. COH fluids are thus effective carriers of C, Mg and Si in the mantle wedge up to the shallowest level of the upper mantle.     

H<Subscript>2</Subscript>O storage capacity of MgSiO<Subscript>3</Subscript> clinoenstatite at 8–13 GPa, 1,100–1,400°C

We present H₂O analyses of MgSiO₃ pyroxene crystals quenched from hydrous conditions in the presence of olivine or wadsleyite at 8–13.4 GPa and 1,100–1,400°C. Raman spectroscopy shows that all pyroxenes have low clinoenstatite structure, which we infer to indicate that the crystals were high clinoenstatite (C2/c) during conditions of synthesis. H₂O analyses were performed by secondary ion mass spectrometry and confirmed by unpolarized Fourier transform infrared spectroscopy on randomly oriented crystals. Measured H₂O concentrations increase with pressure and range from 0.08 wt.% H₂O at 8 GPa and 1,300°C up to 0.67 wt.% at 13.4 GPa and 1,300°C. At fixed pressure, H₂O storage capacity diminishes with increasing temperature and the magnitude of this effect increases with pressure. This trend, which we attribute to diminishing activity of H₂O in coexisting fluids as the proportion of dissolved silicate increases, is opposite to that observed previously at low pressure. We observe clinoenstatite 1.4 GPa below the pressure stability of clinoenstatite under nominally dry conditions. This stabilization of clinoenstatite relative to orthoenstatite under hydrous conditions is likely owing to preferential substitution of H₂O into the high clinoenstatite polymorph. At 8–11 GPa and 1,200–1,400°C, observed H₂O partitioning between olivine and clinoenstatite gives values of D ^ol/CEn between 0.65 and 0.87. At 13 GPa and 1,300°C, partitioning between wadsleyite and clinoenstatite, D ^wd/CEn, gives a value of 2.8 ± 0.4.     

Composition of aqueous fluid coexisting with mantle minerals at high pressure and its bearing on the differentiation of the Earth’s mantle

In order to understand the role of aqueous fluid on the differentiation of the mantle, the compositions of aqueous fluids coexisting with mantle minerals were investigated in the system MgO-SiO₂-H₂O at pressures of 3 to 10 GPa and temperatures of 1000 to 1500°C with an MA8-type multianvil apparatus. Phase boundaries between the stability fields of forsterite + aqueous fluid, forsterite + enstatite + aqueous fluid, and enstatite + aqueous fluid were determined by varying the bulk composition at constant temperature and pressure. The composition of aqueous fluid coexisting with forsterite and enstatite can be defined by the intersection of these two phase boundaries. The solubility of silicate components in aqueous fluid coexisting with forsterite and enstatite increases with increasing pressure up to 8 GPa, from about 30 wt% at 3 GPa to about 70 wt% at 8 GPa. It becomes almost constant above 8 GPa. The Mg/Si weight ratio of these aqueous fluids is much higher than at low pressure (0.2 at 1.5 GPa) and almost constant (1.2) at pressures between 3 and 8 GPa. At 10 GPa, it becomes about 1.4. Aqueous fluid migrating upward through the mantle can therefore dissolve large amounts of silicates, leaving modified Mg/Si ratios of residual materials. It is suggested that the chemical stratification of Mg/Si in the Earth may have been formed as a result of aqueous fluid migration.     

Effects of CO<Subscript>2</Subscript> flushing on crystal textures and compositions: experimental evidence from recent K-trachybasalts erupted at Mt. Etna

Changes in magmatic assemblages and crystal stability as a response of CO₂-flushing in basaltic systems have rarely been directly addressed experimentally, making the role of CO₂ in magma dynamics still controversial and object of scientific debate. We conducted a series of experiments to understand the response of magmas from Etna volcano to CO₂ flushing. We performed a first experiment at 300 MPa to synthesize a starting material composed of crystals of some hundreds of µm and melt pools. This material is representative of an initial magmatic assemblage composed of plagioclase, clinopyroxene and a water-undersaturated melt with 1.6 wt% H₂O. In a second step, the initial assemblage was equilibrated at 300 and 100 MPa with fluids having different XCO ₂ ^fl (CO₂/(H₂O + CO₂)). At low XCO ₂ ^fl (< 0.2 to 0.4), plagioclase is completely dissolved and clinopyroxene show dissolution textures. For relatively high XCO ₂ ^fl (0.9 at 300 MPa), the flushing of a CO₂-rich fluid phase leads to an increase of the amount of clinopyroxene and a decrease of the abundance of plagioclase at 300 MPa. This decrease of plagioclase proportion is associated with a change in An content. Our experiments demonstrate that flushing basaltic systems with fluids may drastically affect crystal textures and phase equilibria depending on proportions of H₂O and CO₂ in the fluid phase. Since texture and crystal proportions are among the most important parameters governing the rheology of magmas, fluid flushing will also influence magma ascent to the Earth’s surface. The experimental results open new perspectives to decipher the textural and compositional record of minerals observed in volcanic rocks from Mt. Etna, and at the same time offer the basis for interpreting the information preserved in minerals from other basaltic volcanoes erupting magmas enriched in CO₂.     

H<Subscript>2</Subscript>O solubility in basalt at upper mantle conditions

This study presents a new experimental approach for determining H₂O solubility in basaltic melt at upper mantle conditions. Traditional solubility experiments are limited to pressures of ~600 MPa or less because it is difficult to reliably quench silicate melts containing greater than ~10 wt% dissolved H₂O. To overcome this limitation, our approach relies on the use of secondary ion mass spectrometry to measure the concentration of H dissolved in olivine and on using the measured H in olivine as a proxy for the concentration of H₂O in the co-existing basaltic melt. The solubility of H₂O in the melt is determined by performing a series of experiments at a single pressure and temperature with increasing amounts of liquid H₂O added to each charge. The point at which the concentration of H in the olivine first becomes independent of the amount of initial H₂O content of the charge (added + adsorbed H₂O) indicates its solubility in the melt. Experiments were conducted by packing basalt powder into a capsule fabricated from San Carlos olivine, which was then pressure-sealed inside a Ni outer capsule. Our experimental results indicate that at 1000 MPa and 1200 °C, the solubility of H₂O in basaltic melt is 20.6 ± 0.9 wt% (2 × standard deviation). This concentration is considerably higher than predicted by most solubility models but defines a linear relationship between H₂O fugacity and the square of molar H₂O solubility when combined with solubility data from lower pressure experiments. Further, our solubility determination agrees with melting point depression determined experimentally by Grove et al. (2006) for the H₂O-saturated peridotite solidus at 1000 MPa. Melting point depression calculations were used to estimate H₂O solubility in basalt along the experimentally determined H₂O-saturated peridotite solidus. The results suggest that a linear relationship between H₂O fugacity and the square of molar solubility exists up to ~1300 MPa, where there is an inflection point and solubility begins to increase less strongly with increasing H₂O fugacity.     

Growth of multilayered polycrystalline reaction rims in the MgO–SiO<Subscript>2</Subscript> system,part I: experiments

Growth of transport-controlled reaction layers between single crystals of periclase and quartz, and forsterite and quartz was investigated experimentally at 1.5 GPa, 1100°C to 1400°C, 5 min to 72 h under dry and melt-free conditions using a piston-cylinder apparatus. Starting assemblies consisting of Per | Qtz | Fo sandwiches produced polycrystalline double layers of forsterite and enstatite between periclase and quartz, and enstatite single layers between forsterite and quartz. The position of inert Pt-markers initially deposited at the interface of the reactants and inspection of mass balance confirmed that both layer-producing reactions are controlled by MgO diffusion, while SiO₂ is relatively immobile. BSE and TEM imaging revealed thicknesses from 0.6 μm to 14 μm for double layers and from 0 to 6.8 μm for single layers. Both single and double layers displayed non-parabolic growth together with pronounced grain coarsening. Textural evolution and growth rates for each reaction are directly comparable. Forsterite–enstatite double layers are always wider than enstatite single layers, and the growth of enstatite in the double layer is slower than that in the single layer. In double layers, the enstatite/forsterite layer thickness ratio significantly increases with temperature, reflecting different MgO mobilities as temperature varies. Thus, thickness ratios in multilayered reaction zones may contain a record of temperature, but also that of any physico-chemical parameter that modifies the mobilities of the chemical components between the various layers. This potential is largely unexplored in geologically relevant systems, which calls for further experimental studies of multilayered reaction zones.     

Ternary system H<Subscript>2</Subscript>O-CO<Subscript>2</Subscript>-NaCl at high <Emphasis Type="Italic">T</Emphasis>-<Emphasis Type="Italic">P</Emphasis> parameters: An empirical mixing model

New experimental data on the solubility of NaCl in gaseous CO₂ were obtained at pressures (P) of 30–70 MPa and temperatures of 623 and 673 K on experimental equipment making possible to sample a portion of the gas in the course of the experiment. The new measures have demonstrated that the NaCl solubility increases with increasing temperature (T) and pressure and is approximately four to five orders of magnitude higher than the saturated vapor pressure of NaCl at the corresponding temperature. The paper also reports newly obtained experimental data on the equilibrium conditions of the reaction of talc decomposition into enstatite and quartz at a variable H₂O/NaCl ratio in the fluid. The results of the experiments validate the empirical equations previously suggested for H₂O and NaCl activities in concentrated aqueous salt solutions that can be used in describing silica-saturated fluids at high T-P parameters. A new empirical equation is suggested for the Gibbs free mixing energy in the H₂O-CO₂-NaCl ternary system, with the parameters of the equation calibrated against experimental data on phase equilibria in marginal binary systems and on the location of the boundary of the region of homogeneous three-component fluid according to data on synthetic fluid inclusions in quartz.     

CO<Subscript>2</Subscript> mineralization of natural wollastonite into porous silica and CaCO<Subscript>3</Subscript> powders promoted via membrane electrolysis

CO₂ is a greenhouse gas, whose emissions threaten the existence of human beings. Its inherently safe sequestration can be performed via CO₂ mineralization, which is relatively slow under natural conditions. In this work, an energy-saving membrane electrolysis technique was proposed for accelerating the CO₂ mineralization of wollastonite into SiO₂ and CaCO₃ products. The electrolysis process involved splitting NH₄Cl into HCl and NH₃·H₂O via hydrogen oxidation and water reduction at the anode and cathode of the electrolytic system, respectively. In contrast to the chlor-alkali electrolysis, this method did not involve Cl^? oxidation and the standard potential of the anode was reduced. Additionally, NH₄Cl was used as the electrolyte instead of NaCl; as a result, the generation of NH₃·H₂O instead of NaOH occurred in the catholyte and the cathodic pH dramatically decreased, thus reducing the cathodic potential for hydrogen evolution. The observed changes led to a 73.5% decrease in the energy consumption. Moreover, after the process of CO₂ mineralization was optimized, SiO₂ with a specific surface area of 221.8 m² g^?1 and CaCO₃ with a purity of 99.9% were obtained.     

Experimental study of eclogite melting with participation of the H<Subscript>2</Subscript>O-CO<Subscript>2</Subscript>-KCl fluid at 5 GPa

In order to model the processes of formation of the highly alkaline (potassic) melts during the partial melting of the eclogite nodules in kimberlites, experiments on the melting of the model and natural eclogites in presence of the H₂O-CO₂ and H₂O-CO₂-KCl fluids at 5 GPa and 1200 and 1300°C are performed. A comparative analysis of the phase relations in the systems with H₂O-CO₂ and H₂O-CO₂-KCl demonstrate that KCl in the fluid equilibrated with eclogites intensifies their melting. It is related to both high Cl concentration in the forming silicate melt (2.0–5.5 wt %) and its enrichment in K₂O owing to the K-Na exchange reactions with the immiscible chloride melt. Because of these reactions, the K₂O/Cl ratio in the melts increases with the KCl content in the system and reaches 2.5–3.5 in the silicate melts coexisting with the immiscible chloride liquid. However, the ratio KCl/(H₂O + CO₂ + KCl) in the fluid does not influence on the ratio K₂O/Cl in the melts. Thus, the solubility KCl in the melts, apparently, does not depend on presence of the H₂O-CO₂ fluid, at least, within the concentration range used in the experiments (up to 20 wt %). The experiments show that the deliberated chloride liquid is necessary to form the potassium-rich chlorine-bearing silicate melts during the eclogite melting. It corresponds to the KCl content in the system above 5 wt %.     

Separation of H<Subscript>2</Subscript>S from CH<Subscript>4</Subscript> by polymeric membranes at different H<Subscript>2</Subscript>S concentrations

In this work, permeation of mixed gases H₂S/CH₄ through commercial polyphenylene oxide (PPO) hollow fiber and poly (ester urethane) urea (PEUU) flat membranes was studied at pressures of 345–689 kPa, at ambient temperature and at 313.15 K. Various H₂S concentrations of about 100–5000 ppm in CH₄ binary synthetic gas mixtures as well as a real natural gas sample obtained from a gas refinery containing 0.3360 mol.% H₂S (equivalent to 3360 ppm) were tested. It was observed that the permeance of components was affected by the balance between competitive sorption and plasticization effects. Separation factors of H₂S/CH₄ were in the range of 1.3–2.9, 1.8–3.1 and 2.2–4.3 at pressures of 345, 517 and 689 kPa, respectively. In the range of 101–5008 ppm of H₂S in CH₄, the effect of temperature on the separation factor was nearly negligible; however, permeances of both components of the mixtures increased with temperature. Additionally, the results obtained by PEUU membrane indicated that it was a better choice for hydrogen sulfide separation from H₂S/CH₄ mixtures than PPO. For PPO membrane, removal of hydrogen sulfide from high-concentration (up to 5008 ppm) binary mixtures of H₂S/CH₄ was compared with that of low concentration (as low as 101 ppm) through PPO. At concentrations of 101–968 ppm, plasticization was dominant compared with the competitive sorption, while for the H₂S feed concentrations of 3048 ppm, the competitive sorption effect was dominant. For H₂S concentration of 5008 ppm, the balance between these two effects played an important role for explanation of its trend.     

Discussion of “Thermodynamic parameters of CaMgSi<Subscript>2</Subscript>O<Subscript>6</Subscript>-Mg<Subscript>2</Subscript>Si<Subscript>2</Subscript>O<Subscript>6</Subscript> pyroxenes based on regular solution and cooperative disordering models” by Holland,Navrotsky, and Newton

Phase equilibria in the join CaMgSi₂O₆-CaFeAlSiO₆-CaTiAl₂O₆ have been determined in air at 1 atm by the ordinary quenching method. Clinopyroxene_ss, forsterite, perovskite, magnetite_ss, spinel_ss, hibonite and an unknown phase X are present at liquidus temperatures (ss: solid solution). At subsolidus temperatures the following phase assemblages were encountered; clinopyroxene_ss+perovskite, clinopyroxene_ss +perovskite+spinel_ss, clinopyroxene_ss +perovskite+melilite (+anorthite), clinopyroxene_ss +perovskite+melilite+spinel_ss+anorthite, clinopyroxene_ss +perovskite+anorthite+spinel_ss, and clinopyroxene_ss +perovskite+anorthite+hibonite. At subsolidus temperatures the single phase field of clinopyroxene_ss extends up to 19 wt.% CaTiAl₂O₆. Even in the field of clinopyroxene_ss+perovskite, the TiO₂ content in clinopyroxene_ss continues to increase and attains 9.2 wt.% TiO₂ with 24.8 wt.% Al₂O₃. An interesting fact is that unusual clinopyroxenes which contain more Al^IV than Si^IV are present in the CaFe-AlSiO₆-rich region. The liquid coexisting with pyroxene is richer in Ti, Al, and Fe³⁺ than the coexisting pyroxene. The clinopyroxenes_ss coexisting with liquid contain less TiO₂, Al₂O₃ and Fe₂O₃ than those crystallized at subsolidus temperatures. The petrological significance of the join and the crystallization of Ti- and Al-rich clinopyroxenes are discussed on the basis of the experimental results of the join.     

Amphibole stability in primitive arc magmas: effects of temperature,H<Subscript>2</Subscript>O content,and oxygen fugacity

The water-saturated phase relations have been determined for a primitive magnesian andesite (57 wt% SiO₂, 9 wt% MgO) from the Mt. Shasta, CA region over the pressure range 200–800 MPa, temperature range of 915–1,070 °C, and oxygen fugacities varying from the nickel–nickel oxide (NNO) buffer to three log units above NNO (NNO+3). The phase diagram of a primitive basaltic andesite (52 wt% SiO₂, 10.5 wt% MgO) also from the Mt. Shasta region (Grove et al. in Contrib Miner Petrol 145:515–533; 2003) has been supplemented with additional experimental data at 500 MPa. Hydrous phase relations for these compositions allow a comparison of the dramatic effects of dissolved H₂O on the crystallization sequence. Liquidus mineral phase stability and appearance temperatures vary sensitively in response to variation in pressure and H₂O content, and this information is used to calibrate magmatic barometers-hygrometers for primitive arc magmas. H₂O-saturated experiments on both compositions reveal the strong dependence of amphibole stability on the partial pressure of H₂O. A narrow stability field is identified where olivine and amphibole are coexisting phases in the primitive andesite composition above 500 MPa and at least until 800 MPa, between 975–1,025 °C. With increasing H₂O pressure (\({P}_{\text {H}_2{\rm O}}\)), the temperature difference between the liquidus and amphibole appearance decreases, causing a change in chemical composition of the first amphibole to crystallize. An empirical calibration is proposed for an amphibole first appearance barometer-hygrometer that uses Mg# of the amphibole and \(f_{\text {O}_2}\):

$$ P_{\text{H}_{2}{\rm O}}({\rm MPa})=\left[{\frac{{\rm Mg\#}}{52.7}}-0.014 * \Updelta {\rm NNO}\right]^{15.12} $$

This barometer gives a minimum \({P}_{\text{H}_{2}{\rm O}}\) recorded by the first appearance of amphibole in primitive arc basaltic andesite and andesite. We apply this barometer to amphibole antecrysts erupted in mixed andesite and dacite lavas from the Mt. Shasta, CA stratocone. Both high H₂O pressures (500–900 MPa) and high pre-eruptive magmatic H₂O contents (10–14 wt% H₂O) are indicated for the primitive end members of magma mixing that are preserved in the Shasta lavas. We also use these new experimental data to explore and evaluate the empirical hornblende barometer of Larocque and Canil (2010).

     

The high-pressure stability of Mg-sursassite in a model hydrous peridotite: a possible mechanism for the deep subduction of significant volumes of H<Subscript>2</Subscript>O

The stability of the high-pressure phase Mg-sursassite, previously MgMgAl-pumpellyite, in ultramafic compositions has been determined in experiments in the system MgO-Al₂O₃-SiO₂-H₂O (MASH). The breakdown of Mg-sursassite + forsterite + enstatite to pyrope + vapour with increasing temperature was bracketed at 6.0 and 7.0 GPa. Below 6.0 GPa, Mg-sursassite + forsterite + vapour reacts to chlorite + enstatite. This reaction provides a mechanism for transfer of water from chlorite- to Mg-sursassite-bearing assemblages. At pressures of 7.0 GPa and above, the assemblage Mg-sursassite + phase A + enstatite was found. Phase relations involving Mg-sursassite and phase A are considered. For bulk compositions with a low water content, the vapour-absent reaction Mg-sursassite + forsterite = pyrope + phase A + enstatite determines the upper-pressure stability of Mg-sursassite, and provides a mechanism for the complete transfer of water from Mg-sursassite to phase A-bearing assemblages. Mg-sursassite plays an important role in peridotite compositions in the subducting slab because, at temperatures below 700 °C, it can transfer water from hydrous phases such as antigorite and chlorite to high-pressure stable phases such as phase A.     

Experimental study of incongruent evaporation kinetics of enstatite in vacuum and in hydrogen gas

Variations in bulk Mg/Si ratios in the various groups of chondritic meteorites indicate that Mg/Si fractionation occurred in the primitive solar nebula. Enstatite (MgSiO₃) evaporates incongruently forming forsterite (Mg₂SiO₄) as an evaporation residue; therefore, evaporation of enstatite produces Mg/Si variations in solid (Mg-rich) and gas (Si-rich) and must be considered as a probable process responsible for Mg/Si fractionation recorded in chondrites. To understand the evaporation kinetics of enstatite, incongruent evaporation experiments on enstatite single crystals have been carried out in vacuum and in hydrogen gas at temperatures of 1300 to 1500°C. A polycrystalline forsterite layer is formed on the surface of enstatite by preferential evaporation of the SiO₂ component, both in vacuum and in hydrogen gas. The thickness of the forsterite layer in vacuum increases with time in the early stage of evaporation and later the thickness of the forsterite layer remains constant (several microns). This is due to the change in the rate limiting process from surface reaction plus nucleation and growth to diffusion in the surface forsterite layer. The activation energy of the diffusion-controlled evaporation rate constant of enstatite is 457 (±58) kJ/mol. A thinner forsterite layer is formed on the surface of enstatite in hydrogen gas than in vacuum. Evaporation of enstatite in hydrogen gas is also considered to be controlled by diffusion of ions through the forsterite layer. The thin forsterite layer formed in hydrogen gas is ascribed to the enhanced evaporation rate of forsterite in the presence of hydrogen gas.The results are applied to incongruent evaporation under the solar nebular conditions. The steady thickness of the forsterite of nebular pressure-temperature conditions is estimated to be submicron because of the enhanced evaporation rate of forsterite under hydrogen-rich nebular conditions if evaporated gases are taken away immediately and no back reaction occurs (an open system). Because enstatite grains in the solar nebula would be comparable to the estimated steady thickness of forsterite, evaporation of such enstatite grains under kinetic conditions could play an important role in producing variations in Mg/Si ratios between solid and gas in the solar nebula.     

Stability of various hydrous phases in CMAS pyrolite-H<Subscript>2</Subscript>O system up to 25 GPa

 We carried out a series of melting experiments with hydrous primitive mantle compositions to determine the stability of dense hydrous phases under high pressures. Phase relations in the CaO–MgO–Al₂O₃–SiO₂ pyrolite with ˜2 wt% of water have been determined in the pressure range of 10–25 GPa and in the temperature range between 800 and 1400 °C. We have found that phase E coexisting with olivine is stable at 10–12 GPa and below 1050 °C. Phase E coexisting with wadsleyite is stable at 14–16 GPa and below 900 °C. A superhydrous phase B is stable in pyrolite below 1100 °C at 18.5 GPa and below 1300 °C at 25 GPa. No hydrous phases other than wadsleyite are stable in pyrolite at 14–17 GPa and 900–1100 °C, suggesting a gap in the stability of dense hydrous magnesium silicates (DHMS). We detected an expansion in the stability field of wadsleyite to lower pressures (12 GPa and 1000 °C). The H₂O content of wadsleyite was found to decrease not only with increasing temperature but also with increasing pressure. The DHMS phases could exist in a pyrolitic composition only under the conditions present in the subducting slabs descending into the lower mantle. Under the normal mantle and hot plume conditions, wadsleyite and ringwoodite are the major H₂O-bearing phases. The top of the transition zone could be enriched in H₂O in accordance with the observed increase in water solubility in wadsleyite with decreasing pressure. As a consequence of the thermal equilibration between the subducting slabs and the ambient mantle, the uppermost lower mantle could be an important zone of dehydration, providing fluid for the rising plumes. Received: 9 September 2002 / Accepted: 11 January 2003 Acknowledgements The authors are thankful to Y. Ito for the assistance with the EPMA measurement, A. Suzuki, T. Kubo and T. Kondo for technical help with the high-pressure experiments and Raman and X-ray diffraction measurements and C.R. Menako for technical support. K. Litasov thanks H. Taniguchi for his continuous encouragement and the Center for Northeast Asian Studies of Tohoku University and the Japanese Society for the Promotion of Science for the research fellowships. This work was partially supported by the Grant-in-Aid of Scientific Research of the Priority Area (B) of the Ministry of Education, Science, Sport, and Culture of the Japanese government (no. 12126201) to E. Ohtani.     

Partitioning of halogens between mantle minerals and aqueous fluids: implications for the fluid flow regime in subduction zones

We have performed phase equilibrium experiments in the system forsterite–enstatite–pyrope-H₂O with MgCl₂ or MgF₂ at 1,100 °C and 2.6 GPa to constrain the solubility of halogens in the peridotite mineral assemblage and the fluid–mineral partition coefficients. The chlorine solubility in forsterite, enstatite and in pyrope is very low, 2.1–3.9 and 4.0–11.4 ppm, respectively, and it is independent of the fluid salinity (0.3–30 wt% Cl), suggesting that some intrinsic saturation limit in the crystal is reached already at very low chlorine concentrations. Chlorine is therefore exceedingly incompatible in upper-mantle minerals. The fluorine solubility is 170–336 ppm in enstatite and 510–1,110 ppm in pyrope, again independent of fluid salinity. Forsterite dissolves 1,750–1,900 ppm up to a fluid salinity of 1.6 wt% F. At higher fluorine contents in the system, forsterite is replaced by the minerals of the humite group. The lower solubility of chlorine by three orders of magnitude when compared to fluorine is consistent with increasing lattice strain. Fluid–mineral partition coefficients are 10⁰–10² for fluorine and 10³–10⁵ for chlorine. Since the latter values are orders of magnitude higher than those for hydroxyl partitioning, fluid flow from the subducting slab through the mantle wedge will lead to an efficient sequestration of H₂O into the nominally anhydrous minerals in the wedge, whereas chlorine becomes enriched in the residual fluid. Simple mass balance calculations reveal that rock–fluid ratios of up to >3,000 are required to produce the elevated Cl/H₂O ratios observed in some primitive arc magmas. Accordingly, fluid flow from the subducted slab into the zone of melting in the mantle wedge does not only occur rapidly in narrow channels, but at least in some subduction zones, fluid pervasively infiltrates the mantle peridotite and interacts with a large volume of the mantle wedge. Together with the Cl/H₂O ratios of primitive arc magmas, our data therefore constrain the fluid flow regime below volcanic arcs.     

The effect of alkalis and polymerization on the solubility of H<Subscript>2</Subscript>O and CO<Subscript>2</Subscript> in alkali-rich silicate melts

The effect of alkalis on the solubility of H₂O and CO₂ in alkali-rich silicate melts was investigated at 500 MPa and 1,250 °C in the systems with H₂O/(H₂O + CO₂) ratio varying from 0 to 1. Using a synthetic analog of phonotephritic magma from Alban Hills (AH1) as a base composition, the Na/(Na + K) ratio was varied from 0.28 (AH1) to 0.60 (AH2) and 0.85 (AH3) at roughly constant total alkali content. The obtained results were compared with the data for shoshonitic and latitic melts having similar total alkali content but different structural characteristics, e.g., NBO/T parameter (the ratio of non-bridging oxygens over tetrahedrally coordinated cations), as those of the AH compositions. Little variation was observed in H₂O solubility (melt equilibrated with pure H₂O fluid) for the whole compositional range in this study with values ranging between 9.7 and 10.2 wt. As previously shown, the maximum CO₂ content in melts equilibrated with CO₂-rich fluids increases strongly with the NBO/T from 0.29 wt % for latite (NBO/T = 0.17) to 0.45 wt % for shoshonite (NBO/T = 0.38) to 0.90 wt % for AH2 (NBO/T = 0.55). The highest CO₂ contents determined for AH3 and AH1 are 1.18 ± 0.05 wt % and 0.86 ± 0.12 wt %, respectively, indicating that Na is promoting carbonate incorporation stronger than potassium. At near constant NBO/T, CO₂ solubility increases from 0.86 ± 0.12 wt % in AH1 [Na/(Na + K)] = 0.28, to 1.18 ± 0.05 wt % in AH3 [Na/(Na + K)] = 0.85, suggesting that Na favors CO₂ solubility on an equimolar basis. An empirical equation is proposed to predict the maximum CO₂ solubility at 500 MPa and 1,100–1,300 °C in various silicate melts as a function of the NBO/T, (Na + K)/∑cations and Na/(Na + K) parameters: \({\text{wt}}\% \;{\text{CO}}_{2} = - 0.246 + 0.014\exp \left( {6.995 \cdot \frac{\text{NBO}}{T}} \right) + 3.150 \cdot \frac{{{\text{Na}} + {\text{K}}}}{{\varSigma {\text{cations}}}} + 0.222 \cdot \frac{\text{Na}}{{{\text{Na}} + {\text{K}}}}.\) This model is valid for melt compositions with NBO/T between 0.0 and 0.6, (Na + K)/∑cation between 0.08 and 0.36 and Na/(Na + K) ratio from 0.25 to 0.95 at oxygen fugacities around the quartz–fayalite–magnetite buffer and above.     

Phototrophic bacteria dominate consortia,potentially to remove CO<Subscript>2</Subscript> and H<Subscript>2</Subscript>S from biogas under microaerophilic conditions

The use of microbial consortia to remove contaminants in industrial systems and in natural environments could be an alternative to the use of unique strains of microorganisms, since microbial consortia have greater robustness to environmental fluctuations. However, it is necessary to evaluate the relationship between the genetic structure and functionality of the consortia. In this work, the functional and structural stability over time of two bacterial consortia (C5 and C6) with the potential to remove CO₂ and H₂S from biogas was evaluated. Both consortia decreased the dissolved CO₂ by over 30% at the end of the incubation period, but C5 presented shorter removal kinetics (3.9 days) than C6 (6.4 days). Additionally, a chemical oxidation of H₂S could have occurred in the microcosms. Moreover, both consortia presented a stable genetic structure, measured by terminal restriction fragment length polymorphism profiles of the 16S rRNA gene, characterized by high homogeneity and prevalence of the genus Rhodopseudomonas throughout the incubation period, and an increasing abundance of Xanthobacter during the exponential phase of the growth curve in C5, which would account for the functionality of the consortia.     

Influence of chlorine substitution on adsorption of gaseous chlorinated phenolics on multi-walled carbon nanotubes embedded in SiO<Subscript>2</Subscript>

Multi-walled carbon nanotubes (MWCNTs) embedded in SiO₂ particles were prepared through the floating-catalyst chemical vapor deposition method. The parameters reaction time and flow rate of the carbon source (CH₄) were studied to obtain optimum conditions for MWCNT synthesis. The obtained MWCNTs were characterized by transmission electron microscopy, scanning electron microscopy, Raman spectroscopy, and Fourier transform infrared spectroscopy to confirm their morphology and crystallinity. The optimum conditions were a CH₄ flow rate of 100 ml/min in a H₂–Ar mixture at a flow rate of 500 ml/min and a reaction time of 20 min. Under these conditions, MWCNTs with average outer and inner diameters of around 50 and 10 nm, respectively, were obtained. SiO₂ particles with embedded MWCNTs were studied for their adsorption of gaseous chlorinated phenolic compounds (CPCs), with emphasis on the effect of number of chlorine substituents. The CPC compounds of 2-chlorophenol (CP) and 2,4-dichlorophenol (DCP) were compared against phenol (P). Adsorption of P and CPCs on the particles fit well the Langmuir isotherm. The adsorption capacities of P, CP, and DCP on SiO₂ particles with embedded MWCNTs were found to be 3.12, 13.83, and 44.25 mg/g, respectively. Desorption activation energy was determined by thermogravimetric analysis. Chlorine substitution on P changed the adsorption process from physical to chemical adsorption. The particles showed high potential for use as a pre-concentration unit for solid-phase microextraction.     

Elastic behavior of vanadinite,Pb<Subscript>10</Subscript>(VO<Subscript>4</Subscript>)<Subscript>6</Subscript>Cl<Subscript>2</Subscript>, a microporous non-zeolitic mineral

The high-pressure behavior of a vanadinite (Pb₁₀(VO₄)₆Cl₂, a = b = 10.3254(5), c = 7.3450(4) Å, space group P6₃/m), a natural microporous mineral, has been investigated using in-situ HP-synchrotron X-ray powder diffraction up to 7.67 GPa with a diamond anvil cell under hydrostatic conditions. No phase transition has been observed within the pressure range investigated. Axial and volume isothermal Equations of State (EoS) of vanadinite were determined. Fitting the P–V data with a third-order Birch-Murnaghan (BM) EoS, using the data weighted by the uncertainties in P and V, we obtained: V ₀ = 681(1) Å³, K ₀ = 41(5) GPa, and K′ = 12.5(2.5). The evolution of the lattice constants with P shows a strong anisotropic compression pattern. The axial bulk moduli were calculated with a third-order “linearized” BM-EoS. The EoS parameters are: a ₀ = 10.3302(2) Å, K ₀(a) = 35(2) GPa and K′(a) = 10(1) for the a-axis; c ₀ = 7.3520(3) Å, K ₀(c) = 98(4) GPa, and K′(c) = 9(2) for the c-axis (K ₀(a):K ₀(c) = 1:2.80). Axial and volume Eulerian-finite strain (fe) at different normalized stress (Fe) were calculated. The weighted linear regression through the data points yields the following intercept values: Fe _a (0) = 35(2) GPa for the a-axis, Fe _c (0) = 98(4) GPa for the c-axis and Fe _V (0) = 45(2) GPa for the unit-cell volume. The slope of the regression lines gives rise to K′ values of 10(1) for the a-axis, 9(2) for the c-axis and 11(1) for the unit cell-volume. A comparison between the HP-elastic response of vanadinite and the iso-structural apatite is carried out. The possible reasons of the elastic anisotropy are discussed.