Wave interaction with T-type breakwaters

The wave transmission, reflection and energy dissipation characteristics of partially submerged ‘T'-type breakwaters (Fig. 1) were studied using physical models. Regular and random waves, with wide ranges of wave heights and periods and a constant water depth were used. Five different depths of immersions of the ‘T'-type breakwater were selected. The coefficient of transmission, K_t, coefficient reflection, K_r, were obtained from the measurements and the coefficient of energy loss, K_l is calculated using the law of conservation of energy. It is found that the coefficient of transmission generally reduces with increased wave steepness and increased relative water depth, d/L. This breakwater is found to be effective closer to deep-water conditions. K_t values less than 0.35 is obtained for both normal and high input wave energy levels, when the horizontal barrier of the T type breakwater is immersed to about 7% of the water depth. This breakwater is also found to be very efficient in dissipating the incident wave energy to an extent of about 65% (i.e. K_l>0.8), especially for high input wave energy levels. The wave climate in front of the breakwater is also measured and studied.

Full-size image (12K)

Fig. 1. Schematic view of the T-type breakwater.     

Hydrodynamic efficiency of partially immersed caissons supported on piles

The efficiency of the breakwater, which consists of caissons supported on two or three rows of piles, was studied using physical models. The efficiency of the breakwater is presented as a function of the transmission, reflection and the wave energy dissipation coefficients. Regular waves with wide ranges of wave heights and periods and constant water depth were used. Different characteristics of the caisson structure and the supporting pile system were also tested. It was found that, the transmission coefficient (k_t) decreases with increasing the relative breakwater draft D/L, increasing the relative breakwater width B/h, and decreasing the piles gap-diameter ratio G/d. It is possible to achieve k_t values less than 0.25 when D/L≥0.1. The reflection coefficient takes the opposite trend especially when D/L≤0.15. The proposed breakwater dissipates about 10-25% of the incident wave energy. Also, simple empirical equations are developed for estimating the wave transmission and reflection. In addition, the proposed breakwater model is efficient compared with other floating breakwaters.     

Investigation of Π-type breakwaters performance under regular and irregular waves

In this paper, performance of solid and perforated Π-type breakwaters was investigated experimentally. Both regular and irregular waves were used during testing. Four depths of immersions were selected for each breakwater and wave type. Different wave groups were generated over these breakwaters, and the transmission, reflection and energy-dissipation characteristics were determined. The results of the experimental study were evaluated and some empirical expressions based on the results were suggested to define the transmission, reflection and energy-dissipation coefficients for different immersion depths of solid and perforated breakwaters under regular and irregular waves. Moreover, performance of solid and perforated Π-type breakwaters were compared with that of solid and perforated U-type breakwaters investigated by Günaydın and Kabdaşlı [2006. Performance of solid and perforated U-type breakwaters under regular and irregular waves. Ocean Engineering 31, 1377–1405]. These comparisons showed that the most reasonable model and wave type are selected to determine requiring performance parameters.     

Numerical prediction of performance of submerged breakwaters

The results of a numerical model study on the transmission characteristics of a submerged breakwater are presented. Study aimed to determine the effect of depth of submergence, crest width, initial wave conditions and material properties on the transmission characteristics of the submerged breakwater. The results highlight the optimum crest width of the breakwater and optimum clear spacing between two breakwaters. A submerged permeable breakwater with d_s/d=0.5, p=0.3 and f=1.0, reduces the transmission coefficient by about 10% than the impermeable breakwater. The results indicates an optimum width ratio of B/d=0.75 for achieving minimum transmission. By restricting the effective width ratio of the series of breakwaters to 0.75, studies were conducted to determine the effect of clear spacing between breakwaters on transmission coefficient, suggesting an optimum clear spacing of w/b=2.00 to obtain K_t below 0.6.     

Wave reflection characteristics of plane, dentated and serrated seawalls

The hydrodynamic performance of vertical and sloped plane, dentated and serrated seawalls were investigated using physical model studies. Regular and random waves of wide range of heights and periods were used. Tests were carried out for different inclinations of the seawall (i.e. θ=30, 40, 50, 60 and 90°) and for a constant water depth of 0.7 m. The wave reflection was measured to assess the dissipation character of the seawalls. It was observed that the serrated seawall was superior to the plane and dentated seawall in reducing the wave reflection. Even for the vertical case, the coefficient of reflection due to regular waves for dentated seawall ranged from 0.6–0.99 and for the vertical serrated seawall it was 0.45–0.98, whereas for the vertical plane wall, it was almost 1.0. It was found that the characteristic dimension of the seawall (i.e. L/W) and the relative water depth (i.e. d/L) were better influencing parameters compared to the conventionally used surf similarity parameter ‘ξ’ (ξ=tan θ/(H_i/L)^0.5) in predicting the reflection from the dentated and serrated seawall, where L is the local wave length, W the width of the dent along the length of the seawall slope, d the water depth at the toe and H_i is the incident wave height. A similar trend was observed for the random waves too. The reduction in the wave reflection due to random waves for the dentated seawall as compared to the plane seawall was about 18% and for the serrated seawall, it was 20%. It was observed that the reflection due to random waves was lesser for all the three different walls than the regular waves, due to the mutual interaction of random waves. Multiple regression analysis on the measured data points was carried out and predictive equations for the reflection coefficient were obtained for both regular and random waves. This study will be useful in the design of energy dissipating type vertical quay walls in ports and harbours, sloped seawalls for shore protection from erosion and sloped caisson as breakwaters. Comparison of predictive formulae with the experimental results revealed that the prediction methods were good enough for practical purposes.     

Performance of solid and perforated U-type breakwaters under regular and irregular waves

An experimental investigation of U-type breakwaters was carried out in a laboratory channel. Both regular and irregular waves were used during testing. Two types of breakwaters such as solid and perforated were studied to analyse the porosity effect of structures. In order to investigate performance of these breakwaters for different immersion depths, four depths of immersions of the solid and perforated breakwaters were selected. Different wave groups were generated over these breakwaters, and the transmission, reflection and energy dissipation characteristics of each breakwater were determined. Three coefficients such as transmission, reflection and energy dissipation coefficients, which were named as C_t, C_r, and C_l, respectively, were used during the evaluation of the test results. The most important parameters governing performance of these breakwaters were determined by using earlier investigations and experimental results. These parameters were expressed as a dimensionless group by using π theory. Based on the test results, empirical expressions were formulated to describe the C_t, C_r, and C_l for different immersion depths of solid and perforated breakwaters under regular and irregular waves.     

Experimental study on the performance of twin plate breakwater

The wave transmission characteristics and wave induced pressures on twin plate breakwater are investigated experimentally in regular and random waves.A total of twenty pressure transducers are fixed on four surfaces of twin plate to measure the wave induced dynamic pressures.The spatial distribution of dynamic wave pressure is given along the surface of the twin plate.The uplift wave force obtained by integrating the hydrodynamic pressure along the structure is presented.Discussed are the influence of different incident wave parameters including the relative plate width B /L,relative wave height /i H a and relative submergence depth s /a on the non-dimensional dynamic wave pressures and total wave forces.From the investigation,it is found that the optimum transmission coefficient,t K occurs around B /L 0.41 ~ 0.43,and the twin plate breakwater is more effective in different water depths.The maximum of pressure ratio decreases from 1.8 to 1.1 when the relative submergence depth of top plate is increased from 0.8to +0.8.     

Prediction of wave pressures on smooth impermeable seawalls

Simple prediction methods are proposed to estimate the wave induced pressures on smooth impermeable seawalls. Based on the physics of the wave structure interaction, the sloped seawall is divided into a total of five zones (zones 1, 2 and 3 during run-up (corresponding pressures are called as positive pressures) and zones 4 and 5 during run-down (corresponding pressures are called negative pressures)) (Fig. 1). Zone 1 (0<z<d−H_i/2), where the wave pressure is governed by the partial reflection and phase shift; Zone 2 (d−H_i/2<z<d), where the effect of wave breaking and turbulence is significant; Zone 3 (d<z<Run-up height), where the pressure is induced by the run-up water; Zone 4 (Run-down<z<d), where the wave pressure is caused by the run-down effect and Zone 5 (0<z<d-Run down), where the negative wave pressures are due to partial reflection and phase shift effects. Here d is the water depth at the toe of the seawall, H_i is the incident wave height and z is the vertical elevation with toe of the seawall as origin and z is positive upward. For wave pressure prediction in zones 1 and 5, the empirical formula proposed by Ahrens et al. (1993) to estimate the wave reflection and Sutherland and Donoghue's recommendations (1998) for the estimation of phase shift of the waves caused by the sloped structures are used. Multiple regression analysis is carried out on the measured pressure data and empirical formulas are proposed for zones 2, 3 and 4. The recommendations of Van der Meer and Breteler (1990) and Schüttrumpf et al. (1994) for the prediction of wave run-down are used for pressure prediction at zone 4. Comparison of the proposed prediction formulas with the experimental results reveal that the prediction methods are good enough for practical purposes. The present study also shows a strong relation between wave reflection, wave run-up, wave run-down and phase shift of waves on wave pressures on the seawalls.     

Full wave solution for hydrodynamic behaviors of pile breakwater

Rayleigh expansion is used to study the water-wave interaction with a row of pile breakwater in finite water depth. Evanescent waves, the wave energy dissipated on the fluid resistance and the thickness of the breakwater are totally included in the model. The formulae of wave reflection and transmission coefficients are obtained. The accuracy of the present model is verified by a comparison with existing results. It is found that the predicted wave reflection and transmission coefficients for the zero order are all highly consistent with the experimental data (Hagiwara, 1984; Isaacson et al., 1998) and plane wave solutions (Zhu, 2011). The losses of the wave energy for the fluid passing through slits play an important role, which removes the phenomena of enhanced wave transmission.     

Hydrodynamic performance of vertical porous structures under regular waves

The hydrodynamic efficiency of the vertical porous structures is investigated under regular waves by use of physical models. The hydrodynamic efficiency of the breakwater is presented in terms of the wave transmission (kt ), reflection (kr) and energy dissipation (kd ) coefficients. Different wave and structural parameters affecting the breakwater efficiency are tested. It is found that, the transmission coefficient (kt ) decreases with the increase of the relative water depth (h/L), the wave steepness (Hi/L), the relative breakwater widths (B/L, B/h), the relative breakwater height (D/h), and the breakwater porosity (n). The reflection coefficient (kr) takes the opposite trend of kt when D/h=1.25 and it decreases with the increasing h/L, Hi/L and B/L when D/h 1.0. The dissipation coefficient (kd) increases with the increasing h/L, Hi/L and B/L when D/h 1.0 and it decreases when D/h=1.25. In which, it is possible to achieve values of kt smaller than 0.3, krlarger than 0.5, and kd larger than 0.6 when D/h=1.25, B/h=0.6, h/L 0.22, B/L 0.13, and Hi/L 0.04. Empirical equations are developed for the estimation of the transmission and reflection coefficients. The results of these equations are compared with other experimental and theoretical results and a reasonable agreement is obtained.     

新型直立式透空堤消浪性能数值研究

为使防波堤同时具有良好的掩护效果和水体交换能力,提出了两种带有透浪通道的新型直立式防波堤。基于Fluent求解器建立了三维数值波浪水槽,通过与试验结果对比,验证了该数值水槽求解波浪与透空堤作用具有较高的精度。对两种防波堤在规则波作用下的透浪特性进行了研究,结果表明:透射系数K_t与透空率呈正线性相关,且可通过调整透浪通道间距,使相同透空率下K_t降低20%～30%。对同一结构,K_t随相对波长的增大而显著增大,但受相对波高的影响较小。在透空率大于0.16后,异型沉箱防波堤的消浪性能明显优于错位沉箱。基于数值计算结果,给出了以上两种透空堤波浪透射系数的经验公式。     

Seakeeping assessment of fishing vessels in conceptual design stage

The main idea of this paper is to identify functional relations between seakeeping characteristics and hull form parameters of Mediterranean fishing vessels. Multiple regression analysis is used for quantitative assessment through a computer software that is based on the SQL Server Database. The seakeeping attributes under investigation are the transfer functions of heave and pitch motions and of absolute vertical acceleration at stern, while the ship parameters influencing motion dynamics have been classified into two groups: displacement (Δ) and main dimensions (L, B, T), coefficients that define the details of the hull form (C_WP, C_VP, LCB, LCF, etc.).Four multiple regression models having different parameter combinations are here investigated and discussed, giving way to the so-called ‘Simple Model’, ‘Intermediate Model’, ‘Enhanced 1 Model’ and ‘Enhanced 2 Model’. The obtained results are more than satisfactory for seakeeping predictions during the conceptual design stage.     

The stability of the antifer units used on breakwaters in case of irregular placement

The primary aim of the study is to experimentally investigate the stability performance of antifer units on the trunk section of breakwaters under the effect of regular and irregular waves in case of irregular placement. The stability performance tests were conducted for different slopes, i.e. cot α=1.25, 1.5, 2.0, 2.5, under irregular waves and for cot α=2.5 under regular waves. Hudson’s formula was employed in order to characterize the stability performance of antifer units for the irregular placement technique. Different representative wave height parameters, i.e. H_s, H_1/10 and H_max, were examined to determine the one best characterizing breakwater stability. Furthermore, the effects of wave period and wave steepness on the stability of the breakwater were explored.     

Effect of under connected plates on the hydrodynamic efficiency of the floating breakwater

In this paper, the hydrodynamic efficiency of a floating breakwater system is experimentally studied by use of physical models. Regular waves with wide ranges of wave heights and periods are tested. The efficiency of the breakwater is presented as a function of the wave transmission, reflection, and energy dissipation coefficients. Different parameters affecting the breakwater efficiency are investigated, e.g. the number of the under connected vertical plates, the length of the mooring wire, and the wave length. It is found that, the transmission coefficient kt decreases with the increase of the relative breakwater width B/L, the number of plates n and the relative wire length l/h, while the reflection coefficient kr takes the opposite trend. Therefore, it is possible to achieve kt values smaller than 0.25 and kr values larger than 0.80 when B/L is larger than 0.25 for the case of l/h-1.5 and n=4. In addition, empirical equations used for estimating the transmission and reflection coefficients are developed by using the dimensionless analysis, regression analysis and measured data and verified by different theoretical and experimental results.     

Equilibrium beach profile model for perched beaches

A beach profile equilibrium model for perched beaches is presented. The model assumes that wave reflection at the seaward and leeward sides of the breakwater is the most important process that modifies Dean's equilibrium profile model for non-perched beaches. The influence of wave breaking over the submerged structure is also discussed. Several laboratory data sets are used to analyze the merit of the proposed model for describing the equilibrium condition of a perched beach. A good comparison is obtained. Results show that if the ratio between the water depth above the submerged structure, d, and the water depth at the toe of the structure, h_e, is large, d/h_e>0.5, only minor advance of the shoreline is achieved with the construction of a toe structure. A considerable advance is obtained for d/h_e less that 0.1. In these situations, however, resonant effects may result in an inefficient structure. The proposed model is used to provide an estimation for the required sand volume and the associated beach advance for the case of narrow breakwaters.     

Wave modelling in the vicinity of submerged breakwaters

This paper describes a simple method for modelling wave breaking over submerged structures, with the view of using such modelling approach in a coastal area morphodynamic modelling system.A dominant mechanism for dissipating wave energy over a submerged breakwater is depth-limited wave breaking. Available models for energy dissipation due to wave breaking are developed for beaches (gentle slopes) and require further modifications to model wave breaking over submerged breakwaters.In this paper, wave breaking is split into two parts, namely: 1) depth-limited breaking modelled using Battjes and Janssen's (1978) theory [Battjes, J.A. and Jannsen, J.P.F.M. (1978). Energy loss and setup due to breaking of random waves. Proceedings of the 16th Int. Conf. Coast. Eng., Hamburg, Germany, pp. 569-587.] and 2) steepness limited breaking modelled using an integrated form of the Hasselmann's whitecapping dissipation term, commonly used in fully spectral wind–wave models. The parameter γ₂, governing the maximum wave height at incipient breaking (H_max = γ₂d) is used as calibration factor to tune numerical model results to selected laboratory measurements. It is found that γ₂ varies mainly with the relative submergence depth (ratio of submergence depth at breakwater crest to significant wave height), and a simple relationship is proposed. It is shown that the transmission coefficients obtained using this approach compare favourably with those calculated using published empirical expressions.     

Analytical investigation of hydrodynamic performance of a dual pontoon WEC-type breakwater

Based on the linear potential flow theory and matching eigen-function expansion technique, an analytical model is developed to investigate the hydrodynamics of two-dimensional dual-pontoon floating breakwaters that also work as oscillating buoy wave energy converters (referred to as the integrated system hereafter). The pontoons are constrained to heave motion independently and the linear power take-off damping is used to calculate the absorbed power. The proposed model is verified by using the energy conservation principle. The effects of the geometrical parameters on the hydrodynamic properties of the integrated system, including the reflection and transmission coefficients and CWR (capture width ratio, which is defined as the ratio of absorbed wave power to the incident wave power in the device width). It is found that the natural frequency of the heave motion and the spacing of the two pontoons are the critical factors affecting the performance of the integrated system. The comparison between the results of the dual-pontoon breakwater and those of the single-pontoon breakwater shows that the effective frequency range (for condition of transmission coefficient K_T < 0.5 and the total capture width ratio η_total > 20%) of the dual-pontoon system is broader than that of the single-pontoon system with the same total volume. For the two-pontoon system, the effective frequency range can be broadened by decreasing the draft of the front pontoon within certain range.     

Stability of breakwater defenced by a seaward submerged reef

The stability of a uniformly sloped conventional rubble mound breakwater defenced by a seaward submerged reef is investigated using physical model studies. Regular waves of wide ranging heights and periods are used. Tests are carried out for different spacings between two rubble mound structures (X/d=2.5–13.33) and for different relative heights (h/d=0.625–0.833) and relative widths (B/d=0.25–1.33) of the reef. It is observed that a reef of width (B/d) of 0.6–0.75 constructed at a seaward distance (X/d) of 6.25–8.33 breaks all the incoming waves and dissipates energy and protects the breakwater optimally.     

双消浪室局部开孔沉箱防波堤反射特性的理论与试验研究

双消浪室局部开孔沉箱防波堤具有低反射、结构受力小、适宜较大水深和工程造价低等优点。为明确双消浪室局部开孔沉箱水动力特性的主要影响因素,采用理论分析和物理模型试验相结合的方法,对规则波和不规则波作用下双消浪室局部开孔沉箱防波堤的反射特性进行研究。基于势流理论,建立规则波和不规则波对局部开孔沉箱防波堤作用的三维解析解,采用二次压力损失边界条件考虑沉箱开孔墙对波浪运动的影响,利用周期性边界条件考虑防波堤结构沿长度方向的周期性变化。开展相应规则波和不规则波物理模型试验,验证理论模型的合理性。通过算例分析,研究不同波浪要素和结构参数对防波堤反射特性的影响。研究表明:双消浪室局部开孔沉箱相对消浪室宽度取值为0.08~0.20,沉箱前墙开孔率大于后墙开孔率时,防波堤在较大波浪频率范围内消波效果显著;当前后墙的开孔率相等时,防波堤反射系数的最小值随着开孔率增大而减小。     

A highly wave dissipation offshore breakwater

The aim of this paper is to develop an offshore breakwater, for which coefficients of both the wave reflection and transmission have low values. The breakwater is suggested to compose of n layers of porous materials with different porosities. A complex eigen function method is used in the theoretical analysis. Continuities of both mass flux and fluid pressure are assumed at interfaces between every two adjoining porous materials and at the interface between end materials and water region. Following a series of mathematical processes, the coefficients of the wave transmission and reflection along with the wave energy loss are calculated. The porosity of materials is varied in computations; and results are compared among structures composing of different layers of porous materials. A single layer offshore breakwater is shown to reduce simultaneously the coefficients of transmission and reflection only when the structure is very wide in the direction of wave propagation, and the structure material has a high porosity. A multilayer breakwater, however, can function well in reducing both coefficients at a much narrower width; structure having more layers can be more effective at narrower width. Finally, several experiments are conducted; theoretical computations and experimental results agree well.