单点系泊网衣构件波浪试验研究

采用四种网箱系泊方法,设计单点系泊网衣构件水槽波浪试验。试验构件由六种网衣和框架装配而成,试验工况是规则波,周期为0．7—2．0s,波高为50—250mm。构件在水槽中作来回周期性直线运动,当试验波浪周期较小时,构件的来回运动不明显,主要以波浪运动为主,水动力峰值大体上呈周期性均匀变化;而当周期较长、波高较高时,构件在水动力的作用下产生了与波向相反的长周期漂移运动,有较大振幅的位移、速度和加速度,诱发了水动力的最大值,水动力变化呈现峰值短周期不均匀变化、最大值长周期变化和零拉力周期变化的规律。试验结果显示,与波高参数类似,随着网衣特性系数d／a的增大,网衣构件的水动力也增大,而水动力最大值长周期、零拉力周期变化规律分别是减短和增长的。在周期1．21、1．41、1．61、1．82s情况下,网衣C构件单点系泊试验水动力最大值是固定系泊计算水动力最大值平均的1．706、1．826、2．125、2．236倍,最大达3．61倍,表明单点系泊在波浪条件下构件水动力有较大的增加。     

带空气透平的后弯管浮式防波堤实验研究

针对海工作业平台、海洋养殖网箱等海洋装备的安全防护问题，提出了一种带空气透平的后弯管浮式防波堤，该空气透平既可将作用在防波堤上的波浪能转化成机械能并用于发电，还可显著减小防波堤的锚链力。在介绍了防波堤原理和结构特点的基础上，设计了物理实验模型，并在实验室造波池内进行了模型试验，研究了波浪周期、波高、吃水深度与弯管数量等因素对后弯管浮式防波堤透射系数和锚链力的影响规律。研究结果表明，波浪周期越短，波高越低，防波堤的透射系数越小，锚 链力越小，其消波性能优于传统的浮式防波堤.     

双浮箱式浮式防波堤消浪性能试验研究

浮式防波堤在港口海岸工程、近海工程、海洋工程和水产养殖等诸多领域有广阔的应用前景。与单浮箱式浮式防波堤相比,多浮箱式浮式防波堤可提高其消浪性能。对双浮箱式浮式防波堤进行了二维波浪物理模型试验,分析了浮箱宽度、前后浮箱连接方式、前后浮箱间距以及浮箱入水深度等因素对浮式防波堤消浪性能的影响。研究结果表明:对于单浮箱式浮式防波堤,试验范围内浮箱宽度增大一倍后消浪效果改善并不相对明显;前后浮箱刚性连接的双浮箱式浮堤的波浪透射系数均小于前后浮箱自由的双浮箱式浮堤和相同浮箱宽度的单浮箱式浮堤,浮堤消浪性能提高;由于前后浮箱相对间距太大时前后浮箱的相互作用减弱,浮堤的波浪反射系数变小,而不同前后浮箱相对间距的波能损耗系数整体上差别较小,双浮箱式浮堤的波浪透射系数整体上随着前后浮箱相对间距D/2B的增大先减小然后变大,在相对间距D/2B为1.0~1.5时双浮箱式浮堤的波浪透射系数相比最小;不同波高和波浪周期下,浮堤的波浪透射系数均随着浮箱相对入水深度的增大而减小。     

浮式防波堤非线性波浪力实验研究

对浮式防波堤在不同吃水深度、周期、波高和入射波波型情况，进行了波浪对浮式防波堤非线性作用力的研究，给出了有关实验结果。实验结果表明波浪力在周期较大时，随着波高的增加，出现一阶力减小、高阶力增大的强非线性现象。实验中出现了二阶力大于一阶力的现象，也出现了三阶力大于二阶力和一阶力的现象。     

T型防波堤与波浪相互作用数值研究

针对T型透空式防波堤,通过浪高仪采集防波堤前后不同位置波面变化曲线,使用声学多普勒流速仪(NDV)测量不同位置流速随时间的变化,并分析了其相位平均流速的分布。基于VOF法的二维波浪数值水槽,对规则波作用下T型防波堤附近的动力特性进行了计算,水槽模型试验结果和数值模拟结果对比表明,数值计算结果与实验值吻合较好。采用该模型进一步对T型防波堤附近波浪场、流线、紊动动能、紊动动能耗散率变化以及不同尺寸的防波堤消浪效果进行模拟计算,重点分析了入射波高、防波堤入水深度和防波堤宽度变化的影响。     

新型直立式透空堤消浪性能数值研究

为使防波堤同时具有良好的掩护效果和水体交换能力,提出了两种带有透浪通道的新型直立式防波堤。基于Fluent求解器建立了三维数值波浪水槽,通过与试验结果对比,验证了该数值水槽求解波浪与透空堤作用具有较高的精度。对两种防波堤在规则波作用下的透浪特性进行了研究,结果表明:透射系数K_t与透空率呈正线性相关,且可通过调整透浪通道间距,使相同透空率下K_t降低20%～30%。对同一结构,K_t随相对波长的增大而显著增大,但受相对波高的影响较小。在透空率大于0.16后,异型沉箱防波堤的消浪性能明显优于错位沉箱。基于数值计算结果,给出了以上两种透空堤波浪透射系数的经验公式。     

方形网箱水平波浪力的迭加计算和实验验证

采用小直径圆柱体绕流理论和网渔具理论为基础的经验水动力计算法，分别考虑网箱框架是刚性体、网衣和绳索是柔性体的特征，结合正弦波理论对方形网箱及其构件受到的水平波浪力特性进行了分析研究，理论给出了波浪力迭加计算法，并把计算结果与小尺度的网箱水槽实验进行对比验证。结果表明，计算数值与试验数据较接近，平均误差率在15％以内。网箱水平波浪力呈周期性、不对称变化，在波浪周期小于0.72s时，主要以框架的波浪力为主，反之以网衣的为主。在波长为0.8m、周期为0.72s、水深为0.7m、波高为68.3mm情形下，计算结果显示网箱的框架尺寸和形状及其系泊、布局的选择应根据实际海况而定，网箱高度可适当增加，当设置水层下降深度相对于网箱高度比率为20％-40％，时，波浪力峰值下降相对率达68.03％-88.20％，表明可以较大程度地降低其波浪力。     

新型浮式防波堤水动力性能数值研究

针对设计的新型双浮筒+Savinious型(S型)桨叶浮式防波堤的结构形式,基于势波理论和结构耦合水动力分析理论,利用面元积分和Newmark-β时间步进格式进行计算,研究其在线性规则波作用下的消波性能、运动响应和系泊张力响应,验证该结构的合理性。数值计算结果表明,阻尼修正后的防波堤纵摇运动响应合理,在波高H=1.5 m、波浪周期T=3 s下其消浪性能较为理想,透射系数达到0.65,同时系泊线张力呈周期响应并满足最大破断力的条件。此外,还研究了浮筒相对间距S1/L,浮筒—桨叶相对间距S2/L以及Savinious型桨叶高径比d/h三个无量纲关键几何参数对防波堤透射系数Ct和系泊线时域张力响应的影响。计算结果表明,浮筒间距S1越接近波长,防波堤消波性能越好,但迎浪侧张力响应幅值越大;随着浮筒—桨叶相对间距S2/L由0趋近于1,其透射系数随之减小,但迎浪侧张力响应幅值基本保持不变;减小桨叶的高径比d/h可以提高防波堤消波性能的稳定性,但张力响应幅值随之增大。     

弧板式透空堤消浪性能影响因素数值研究

弧板式透空堤是由弧型板组成的新型防波堤结构。为探讨其透射系数的影响因素,利用Fluent软件基于N-S方程构建了波浪与板式透空堤相互作用的数值模型,讨论了相对潜深、入射波周期、相对波高、相对板宽和结构型式对透射系数的影响。结果表明:弧板式透空堤的透射系数随着相对波高和入射波周期的增大而增大,在静水面附近透射系数最小,尤以静水面和略高于静水面时的消浪效果最佳;在相同波浪要素条件下,静水面及其上0.02 m和0.04 m位置处,弧板式透空堤的消浪效果明显优于平板式透空堤。     

弧形防波堤波浪力试验研究

在圆筒形防波堤和V形防波堤的基础上,结合离岸堤后形成V形和半圆形连续出现的韵律海岸的地貌平面形态特点,提出一种前墙为连续的半圆筒形防波堤形式。通过在波浪水槽内进行规则波物理模型试验,探究这一新型防波堤的波压力分布规律及波高、周期、水深等因素对波压力的影响。将试验结果与海港水文公式和合田良实公式计算的理论值对比分析,给出了以合田良实公式的折减系数来拟合新型弧形防波堤波浪总水平力的计算公式。结果表明:新型弧形防波堤上的波压力随波高、周期的增大而增大,其水平波浪总力比同等尺度直墙少10%左右。     

A Review of Some Environmental Issues Affecting Marine Mining

This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested.     

Increased Particle Fluxes at the INDEX Site Attributable to Simulated Benthic Disturbance

Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement.     

Assessing the Validity of Seismo-Acoustic Predictor Equations for Obtaining Seabed and Sub-Surface Sediment Physical Properties

The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths.     

海上大直径钢管桩打桩过程中桩周土强度弱化研究

海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。     

Determination of In Situ Sediment Shear Strength from Advanced Piston Corer Pullout Forces

The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments.     

Interannual Sea Level Variations and Annual Tides in the Northwestern Pacific

Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone.     

《Acta Oceanologica Sinica》Vol. 33(2014) contents

<正>~~     

INFORMATION FOR AUTHORS

<正>Acta Oceanologica Sinica(AOS)is a comprehensive academic journal edited by the Editorial Committee of Acta Oceanologica Sinica and is designed to provide a forum for important research papers of the marine scientific community which reflect the information on a worldwide basis.The journal publishes scholarly papers on marine science and technology,including physics,chemistry,biology,