Interaction of non-breaking regular waves with a periodic array of artificial porous bars

A computational model is developed to investigate the wave damping characteristics of a periodic array of porous bars. The transmission and reflection coefficients as well as the wave energy dissipation are evaluated relating to the physical properties and geometric factors of bars. It is shown that the porosity, number, width and height of bars all play important roles in the wave damping characteristics, compared to other factors such as the intrinsic permeability. It is observed that like impermeable bars, permeable bars display Bragg phenomenon. However, Bragg reflection produced by permeable bars is smaller than that by impermeable bars. Permeable bars reflect smaller waves, transmit smaller waves and dissipate more wave energy. It is indicated that if the porosity increases, both the reflection and transmission coefficients decrease and more wave energy is dissipated. Further, it is found that the porosity controls the magnitude, but not the oscillation frequency of the reflection coefficient, which depends only on the number of bars.     

Wave interaction with a perforated wall breakwater with a submerged horizontal porous plate

This study examines the hydrodynamic performance of a new perforated-wall breakwater. The breakwater consists of a perforated front wall, a solid back wall and a submerged horizontal porous plate installed between them. The horizontal porous plate enhances the stability and wave-absorbing capacity of the structure. An analytical solution based on linear potential theory is developed for the interaction of water waves with the new proposed breakwater. According to the division of the structure, the whole fluid domain is divided into three sub-domains, and the velocity potential in each domain is obtained using the matched eigenfunction method. Then the reflection coefficient and the wave forces and moments on the perforated front wall and the submerged horizontal porous plate are calculated. The numerical results obtained for limiting cases are exactly the same as previous predictions for a perforated-wall breakwater with a submerged horizontal solid plate [Yip, T.L., Chwang, A.T., 2000. Perforated wall breakwater with internal horiontal plate. Journal of Engineering Mechanics ASCE 126 (5), 533–538] and a vertical wall with a submerged horizontal porous plate [Wu, J.H., Wan, Z.P., Fang, Y., 1998. Wave reflection by a vertical wall with a horizontal submerged porous plate. Ocean Engineering 25 (9), 767–779]. Numerical results show that with suitable geometric porosity of the front wall and horizontal plate, the reflection coefficient will be always rather small if the relative wave absorbing chamber width (distance between the front and back walls versus incident wavelength) exceeds a certain small value. In addition, the wave force and moment on the horizontal plate decrease significantly with the increase of the plate porosity.     

Interaction of cnoidal waves with an array of vertical concentric porous cylinders

An array of large concentric porous cylinder arrays is mounted in shallow water exposed to cnoidal waves. The interactions between waves and cylinders are studied theoretically using an eigenfunction expansion approach. Semi-analytical solutions of hydrodynamic loads and wave run-up on each cylinder are obtained using first approximation to cnoidal waves. The square array configuration of four-legged identical concentric porous cylinder is investigated in present study. Numerical results reveal the variation of dimensionless wave force and wave run-up on individual cylinder with angle of incidence, porosity parameter, spacing between outer and inner cylinders, spacing between concentric porous cylinders and wave parameter. Different mechanism of wave force is found under different range of scattering parameter.     

Hydrodynamics identities and wave-drift force of a porous body

In the present study, hydrodynamic interactions between water waves and porous bodies are investigated. Various hydrodynamic identities, such as the Haskind relation, Bessho-Newman relation etc., are systematically re-examined. Some of these identities, such as the symmetry of added mass and damping and the Haskind-Hanaoka relation, are still valid for porous bodies even without modification to the identities. However, when energy dissipation due to porosity is involved, appropriate supplementation is required to properly consider porous effects. In addition, the calculation of wave drift forces acting on a porous body is formulated either by pressure integration or using momentum conservation as basis. We conclude that porosity dissipation makes a more substantial contribution to wave drift forces than does conventional dissipation created by scattered and radiated waves.     

Wave motion over a submerged breakwater with an upper horizontal porous plate and a lower horizontal solid plate

This study examines the hydrodynamic performance of a modified two-layer horizontal-plate breakwater. The breakwater consists of an upper submerged horizontal porous plate and a lower submerged horizontal solid plate. By means of the matched eigenfunction expansion method, a linear analytical solution is developed for the interaction of water waves with the structure. Then the reflection coefficient, the transmission coefficient, the energy-loss coefficient and the wave forces acting on the plates are calculated. The numerical results obtained for limiting cases are exactly the same as previous predictions for a single submerged horizontal solid plate and a single submerged horizontal porous plate. Numerical results show that with a suitable geometrical porosity of the upper plate, the uplift wave forces on both plates can be controlled at a low level. Numerical results also show that the transmission coefficient will be always small if the dimensionless plate length (plate length versus incident wavelength) exceeds a certain moderate value. This is rather significant for practical engineering, as the incident wavelength varies over a wide range in practice. Moreover, it is found that the hydrodynamic performance of the present structure may be further enhanced if the lower plate is also perforated.     

Experimental investigating on the reflected waves from the caisson-type vertical porous seawalls

The hydrodynamic efficiencies of caisson-type vertical porous seawalls used for protecting coastal areas were calculated in this study. Physical models were developed to compare the wave reflection from vertical plane, semi-porous, and porous seawalls caused by both regular and random waves. Tests were carried out for a wide range of wave heights, wave periods, and different water depths (d=0.165, 0.270 and 0.375 m). The performance regarding the reflected waves from porous and semi-porous seawalls showed improvement when compared with those from the plane seawall. The reflection coefficients of the porous and semi-porous seawalls were calculated as 0.6 and 0.75, respectively, while the coefficient for the fully reflecting plane vertical wall was significantly higher (0.9). It was also observed that the reflection coefficient decreases with increase in wave steepness and relative water depth. In addition, the reduction in the reflection coefficient of porous and semi-porous seawalls, as compared to that of a plane seawall, was observed for both regular and random waves. New equations were also proposed to calculate the reflection coefficient of different types of seawalls with the aid of laboratory experiments. By verifying the developed equations using some other experimental data, it was validated that the equations could be used for practical situations. The results of the present study can be applied to optimize the design of vertical seawalls and for coastal protecting schemes.     

Analysis of A Porous and Flexible Cylinder in Waves

The hydrodynamic response of a porous flexible circular-cylinder in regular waves was analytically studied. To simplify the problem, the cover and the bottom of the cylinder were ignored. Small amplitude water wave theory and structural responses were assumed. The velocity potentials were solved using the Fourier-Bessel series expansion method and the least squares approximation method. The convergence of the series was numerically tested to determine the number of terms in the series expansion. Two types of installations were considered for deformation, hydrodynamic forces, structural flexibility, drafts, and porosity. The present study represented a preliminary step in the study of the fish cage.     

Hydrodynamic characteristics of semi-immersed breakwater with an attached porous plate

In the present study, wave interaction with a fixed, partially immersed breakwater of box type with a plate attached (impermeable-permeable) at the front part of the structure is investigated numerically and experimentally. The large scale laboratory experiments on the interaction of regular waves with the special breakwater were conducted in the wave flume of Laboratori d’Enginyeria Marνtima (LIM) at Universitat Politecnica de Catalunya (UPC) in Barcelona. Experimental results are compared with numerical results obtained with the use of the Cornell breaking Wave and Structures (COBRAS) wave model. The effects of an impermeable as well as a permeable plate attached to the bottom of the breakwater on its hydrodynamic characteristics (wave transmission, reflection, dissipation, velocity and turbulence kinetic energy) are investigated. Computed velocities and turbulence kinetic energy in the vicinity of the structure indicate the effects of the breakwater with the attached (impermeable/permeable) plate on the flow pattern and the turbulence structure. The attached impermeable plate at the front part of the breakwater enhances significantly the efficiency of the structure in attenuating the incident waves. The permeable plate reduces the efficiency of the structure since wave energy is transmitted through the porous body of the plate. Based on the hydrodynamic characteristics it is inferred that the breakwater with an impermeable plate attached to its bottom is more efficient. The comparison of horizontal and vertical forces acting on the breakwater for all cases examined reveals that plate porosity influences slightly vertical force and severely horizontal force acting on the structure, reducing maximum values in both cases.     

Wave reflection by a vertical wall with a horizontal submerged porous plate

By applying the linear water wave theory and the eigenfunction expansion method, the wave reflection by a vertical wall with a horizontal submerged porous plate is investigated in this paper. The numerical results, concerning the effects of the dimensionless plate length, the relative water depth, and the porous effect parameter of the plate on the wave loads on the plate and the wave height near the wall as well as the reflection coefficient, are discussed. It is found that the submerged plate increases the complexity of the phenomenon related to the wave reflection and refraction in the close region of the wall, and leads to the occurrence of the phenomenon of wave trapping. The results indicate that there may exist a process of focusing wave energy near the wall for small dimensionless porous effect parameters, whereas the increase of the dimensionless porous effect parameter decreases gradually the wave height until setdown occurs. The behavior of a larger plate with proper porosity is similar to that of a wave absorber which can significantly suppress not only the wave height above the plate but also the reflection waves. The ability of the porous plate to reduce the wave height on the wall surface is, in general, directly proportional to the dimensionless plate length and may be strongest for a proper value of the dimensionless porous effect parameter. It is also demonstrated that the wave loads on a porous plate are smaller than those on an impermeable plate.     

基于类海啸波型的岛礁水动力特性数值模拟研究

基于非静压单相流模型NHWAVE建立了高精度二维数值波浪水槽,采用日本2011年实测真实海啸波型系统研究了海啸波在岛礁上传播变形的规律,并且分析了波高、礁坪淹没水深和礁前斜坡坡度等因素对孤立波和真实海啸传播变形的影响。结果表明,相比孤立波,类海啸波的波长明显大于孤立波波长,在测点处引起的水面变化持续时间更长,同等波高情况下真实海啸波型比孤立波能够携带更多的能量,与岛礁的相互作用也更为复杂,在礁坪上形成的淹没水深约为孤立波的两倍。礁前斜坡坡度和礁坪淹没水深均对类海啸波的反射和透射系数有显著影响。随着礁前斜坡坡度的增加,反射系数和透射系数均逐渐增加。随着礁坪淹没水深的增加,反射系数逐渐减小,而透射系数逐渐增大。但是,反射系数和透射系数均随着入射波高的增加而逐渐减小。     

Hydrodynamic behavior of curtainwall-pile breakwaters

A numerical model is developed that can predict the interaction of regular waves normally incident upon a curtainwall-pile breakwater; the upper part of which is a vertical wall and the lower part consists of an array of vertical piles. The numerical model is based on an eigenfunction expansion method, and utilizes a boundary condition nearby the vertical piles that accounts for wave energy dissipation. Numerical solution comprises a finite number of terms, which is a superposition of propagating waves and a series of evanescent waves. The modeling is validated by comparison with previous experimental studies and overall agreement between measurement and calculation is fairly good. The numerical results are related to reflection, transmission, and dissipation coefficient; wave run-up, wave force, and wave overturning moment are also presented. Effect of porosity, relative draft, and relative water depth are discussed; the choice of suitable range of them is described. The relative draft is more effective for shallow water waves. Model shows decrease in relative draft and leads to reduction of relative wave force, overturning moment, and runup. It is shown that curtainwall-pile breakwaters can operate both effectively and efficiently in the range of relative draft between 0.15 and 0.75. The range 0.5 to 0.2 is also recommended for porosity.     

Wave reflection from vertical breakwater with porous structure

This paper presents numerical solutions for the wave reflection from submerged porous structures in front of the impermeable vertical breakwater. A new time-dependent mild-slope equation involves the parameters of the porous medium including the porosity, the friction factor and the inertia coefficient, etc. is derived for solving the boundary value problem. A comprehensive comparison between the present model and the existing analytical solution for the case of simple rectangular geometries of the submerged structure is performed first. Then, more complicated cases such as the inclined and trapezoidal submerged porous structures in front of the vertical breakwater with sloping bottom are considered. This study also examines the effects of the permeable properties and the geometric configurations of the porous structure to the wave reflection. It is found that the submerged porous structure with trapezoidal shape has more efficiency to reduce the wave reflection than that of triangular shape. The numerical results show that the minimum wave reflection is occurred when the breakwater is located at the intermediate water depth.     

Numerical Wave Flume Study on Wave Motion Around Submerged Plates

1 .IntroductionApile supportedplatesubmergedatacertaindepthunderseasurfacewasdevelopedasanewtypeofunderwaterbreakwaterfortheprotectionofcoastlinesandharbors .Thisisbecauseitdoesnothinderthewaterexchangebetweentheopenseaandtheprotectedareanordoesithindertheviewovertheopensea .Besides,itislessdependentonthegeotechnicalconditionsoftheseabottomwherethestructureistobeinstalled ;however,itscostishigh ,particularlyinrelativelydeepwaters .Formanyapplicationsitispossibletoreducethewavemotionintheprotec…     

Wave reflection and transmission by curtainwall–pile breakwaters using circular piles

This paper presents a mathematical model which computes the hydrodynamic characteristics of a curtainwall–pile breakwater (CPB) using circular piles, by modifying the model developed for rectangular piles by Suh et al. [2006. Hydrodynamic characteristics of pile-supported vertical wall breakwaters. Journal of Waterway, Port, Coastal and Ocean Engineering 132(2), 83–96]. To examine the validity of the model, laboratory experiments have been conducted for CPB with various values of draft of curtain wall, spacing between piles, and wave height and period. Comparisons between measurement and prediction show that the mathematical model adequately reproduces most of the important features of the experimental results. The mathematical model based on linear wave theory tends to over-predict the reflection coefficient as the wave height increases. As the draft of the curtain wall increases and the porosity between piles decreases, the reflection and transmission coefficient increases and decreases, respectively, as expected. As the relative water depth increases, however, the effect of porosity disappears because the wave motion is minimal in the lower part of a water column for short waves.     

斜向波与带填料开孔板式防波堤相互作用的研究

基于线性势流理论,对斜向波与消浪室内带部分填料的开孔板式防波堤结构的相互作用进行了理论研究.利用匹配特征函数展开法给出了开孔防波堤结构反射系数和波浪力系数的理论计算方法,在极限情况下的计算结果与已有结果一致.利用数值算例分析了开孔结构反射系数和波浪力系数的主要影响因素.增加消浪室内填料厚度通常可以降低开孔墙结构的波浪力系数,加大结构的反射系数.随着波浪入射角度的增加,带填料防波堤结构的反射系数值先减小,达到最小值后又单调增加.     

The theoretical study on diagonal wave interaction with perforated-wall breakwater with rock fill

The interaction of diagonal waves with perforated-wall breakwater partially filled with rock fill is studied using the linear potential theory. By means of the matched eigenfunction expansion method, an analytical method is presented to calculate the reflection coefficient and the wave force coefficient of the breakwater. The calculated results of the reflection coefficient for limiting cases are the same to the existing results. The main effect factors of the reflection coefficient and the wave force coefficient are analyzed by numerical examples. With the increasing of thickness of rock fill, the wave force coefficient on the perforated wall generally decreases, while the reflection coefficient increases. With the increasing of the incident angle of the wave, the reflection coefficient of the breakwater first decreases, reaches its minimum, and then increases monotonously.     

Wave interaction with a concentric porous cylinder system

This is a theoretical investigation of wave interaction with a concentric surface-piercing two-cylinder system. The exterior cylinder is porous and considered to be thin in thickness and the interior cylinder is impermeable. Both cylinders are rigidly fixed at the sea bed. The fluid motion is idealized as a linearized potential flow. The free-surface elevation and the total net hydrodynamic forces acting on both cylinders are determined analytically. The wave-induced overturning moments are also evaluated. It is found that, with the existence of the exterior porous cylinder, the hydrodynamic force acting on the interior cylinder is reduced if compared to the force exerted on the interior cylinder by a direct wave impact. The reduction of the wave amplitude around the leeward side of the outer porous cylinder is shown from the free-surface computations. In this paper, results are also presented to illustrate the effects of wave parameter and structural porosity on this wave and cylinder interaction problem. The role played by the ratio of radii of the inner and outer cylinders is duscussed.     

聚焦波作用下平面网衣结构的水动力特性研究

由于沿海区域的限制以及愈加严重的环境污染,渔业养殖正从近海走向深远海。深远海海域的海况更加恶劣,给养殖装备的设计与性能评估带来新的挑战。为解决该问题,对极端波浪与养殖装备网衣结构的相互作用开展研究。基于waves2Foam建立数值波浪水池,极端波浪模拟采用基于NewWave理论的聚焦波模型,网衣结构模拟采用多孔介质模型,并通过与Morison模型计算的网衣受力等效分析,获得多孔介质模拟网衣结构阻力系数的直接估计方法。然后将多孔介质模型嵌入waves2Foam中,开展聚焦波与网衣结构相互作用的数值模拟,同时开展水槽试验,验证数值模拟的准确性。基于数值模拟结果,系统地分析了不同网衣密实度及不同波浪参数下网衣结构的升阻力特性以及网衣结构对波浪场的扰动规律。研究表明：聚焦波波峰幅值和网衣密实度对网衣结构的升阻力影响较大,且升力峰值出现在阻力为0的时刻;网衣结构对聚焦波的时空演化特性有影响,改变了聚焦波波形。     

Reflected and transmitted waves in a channel with side porous mattresses

The problem of wave propagation and wave damping in a channel with side porous mattresses of arbitrary shape protruding from the walls is studied. The solution was achieved by applying 3-D boundary element method and was employed to study wave field in the channel and to analyze the effect of the geometry of the mattresses and physical and hydraulic properties of porous material on wave damping. The results show that wave damping in the channel strongly depends on wave parameters, especially, on the wave number. Wave reflection and transmission decrease with increasing the wave number. The results also show that the wave field in the channel strongly depends on the geometry of the mattresses as well as on physical and hydraulic properties of porous material used to build these wave dampers. The geometry of the mattresses and physical and hydraulic properties of porous material have a moderate effect on wave reflection and a significant effect on wave transmission. The results show that wave transmission down the channel decreases with increasing the length and thickness of the mattresses. Moreover, wave transmission decreases with increasing the porosity and damping properties of porous media used to build the mattresses. The analysis shows that porous mattresses protruding from the channel walls are very efficient in damping water waves propagating down the channel and may be built in channels to reduce high waves and achieve desired wave conditions. Theoretical results are in reasonable agreement with experimental data.     

Wave forces on a seawater intake caisson

The wave force on a seawater intake structure consisting of a perforated square caisson of 400 mm×400 mm size encircling a vertical suction pipe of 160-mm diameter is investigated using physical model studies. The porosity of caisson was varied from 1.6 to 16.9%. Regular and random waves of wide range of heights and periods were used. It is found that the force ratio (ratio of the force on perforated caisson to the force on caisson with zero percent porosity) reduces to an extent of up to 60% with increase in porosity of the caisson from 1.6 to 16.9%. The force ratio was found to increase with increase in relative wave height and reduces with increase in relative width. Multiple regression analysis of the measured data points was carried out and predictive equations for wave force ratios are obtained both for regular and random waves. The results of this investigation can be used in the hydrodynamic design of perforated caissons, which are widely used as seawater intake structures.