不同尺度人工岛波浪绕射系数的研究

为研究人工岛沿波浪传播方向尺度变化对绕射系数的影响,本文基于MIKE21-BW模型,数值模拟研究了入射波为不规则波时人工岛尺度不同对其绕射系数的影响。通过数值结果与Briggs物理模型试验结果进行了对比,结果吻合较好,验证了模型在研究波浪绕射问题上的适用性。在未考虑结构物沿波浪传播方向尺度对绕射系数的影响时,将数值结果与《海港水文规范》(JTS145-2-2013)规范结果比对,结果差异较小;本文采用上述模型模拟了结构物沿波浪传播方向7种不同尺度时的波浪绕射情况,分别是0.5Ls,Ls,2Ls,3Ls,4Ls,5Ls及6Ls,通过对不同尺度时的波浪绕射系数变化的分析,得到结果:结构物尺度在0.5Ls~2Ls范围内时,绕射系数随着结构物尺度的增大而变大;结构物尺度在3Ls~6Ls范围内时,绕射系数随着结构物尺度的增大而减小;在人工岛岛壁附近和其掩护区内绕射系数变化较明显;人工岛结构物尺度变化对绕射系数值有影响。文中给出了不同尺度人工岛绕射系数等值线图,可为工程设计中绕射波高确定提供参考。     

波浪在三维圆形岛地形上的绕射研究

波浪在传播过程中遇到岛屿就会发生绕射。本文使用混合元方法对修正型缓坡方程进行了数值求解,并与KUO et al的解析解进行了比较验证。在此基础上研究了工程尺度背景下,波浪在三维圆形岛地形上的绕射,计算了不同入射波浪周期、浅滩形状参数和岛屿尺寸情况下,沿波浪传播方向断面上和岛屿岸线上的相对波高大小。计算结果表明：随着入射波周期的减小、浅滩形状参数的增大和岛屿尺寸的减小,圆形岛迎浪侧的相对波高振荡幅度、圆形岛背浪侧的相对波高大小以及岛屿岸线上的相对波高振幅和大小均随之增大。不同情况下,岛屿岸线上的相对波高最大值大多数发生在迎浪点,个别发生在迎浪点两侧20°~25°处;最小值发生在背浪点两侧30°附近。     

作用在大直径圆柱墩上不规则波波浪力的试验研究

本文介绍大直径圆柱墩不规则波波浪力的确定方法,本法基于波浪绕射理论及随机海浪的极值分布理论而建立,经过不规则波波力试验,证实它是合理并可靠的。文中讨论了波力谱的表达式,波力及波力矩的统计分布特征及波力谱(或波力矩谱)与波浪谱峰频值ω_0的关系。     

水下圆形浅滩附近波浪绕射的计算

采用波数矢量无旋和波能守恒方程对圆形浅滩附近水域波浪绕射进行了数值计算,计算模型中采用Ｂａｔｔｊｅｓ关系与波数矢量无旋,波能量守恒方程一起联合求解圆形浅滩附近水域波浪折射影响下的波浪要素。本文的数值计算模型对圆形浅滩水域波浪折射绕射现象的验证结果表明,计算所得结果与试验结果是吻合的,数学模型是可靠和合理的,具有实用价值。     

多方向不规则波传播变形数值模拟

在推广的缓坡方程数学模型基础上建立了多方向不规则波数学模型,综合考虑了波浪折射、绕射、反射、底摩擦和风能输入等因素。基于线性波浪理论,将波浪方向谱在频率和方向上按等能量分割法离散后,分别计算各组成波的传播变形,再计算合成波要素。缓坡方程数学模型采用改进的ADI法求解,计算效率高,稳定性好。采用椭圆形浅滩不规则波模型试验结果和单突堤不规则波绕射理论解对数学模型进行了验证,数值模拟结果和试验值及理论解符合良好。利用该模型进行了某港港内波浪折射、绕射和反射的联合数值模拟,给出了合理的港内波高分布。     

矩形人工岛波浪爬高的数值模拟

本文基于线性绕射理论,提出了采用波源分布法计算矩形人工岛上波浪爬高的数值模型.在三种入射波向(α=0°、45°、90°)下进行数值计算,所得到的结果与整体模型试验的实测结果进行了比较,二者吻合较好.表明波源分布法是确定波浪爬高的一个有效方法,可为人工岛工程设计提供可靠的高度参数.     

基于抛物型缓坡方程模拟近岸植被区波浪传播

植被对波浪传播运动有重要影响。考虑近岸波浪在植被区传播中的折射、绕射、破碎及植被引起的波能耗损效应,基于抛物型缓坡方程建立了模拟近岸植被区波浪传播的数学模型,对模型进行了数值模拟验证,采用数值模拟试验分析了植被对波浪传播的影响。数值模拟结果表明,波浪在近岸植被区传播时,随着植被密度和植被高度的增加,波浪传播中的波高衰减增大,波能耗损增加;不同周期波浪在植被区传播中的波高衰减过程也明显不同。     

多向不规则波绕射的数值模拟

采用有限元求解Ｂｏｕｓｓｉｎｅｓｑ方程数值计算模型,对单突堤和双突堤的波浪绕射进行了数值模拟,并与物模试验进行对比验证。模拟结果表明入射波浪的方向分布对波浪的绕射具有明显的影响,使防波堤后的波浪增大,开阔区域的浪浪减小,波浪的方向分布对港内波浪的分布具有一定的均化作用。     

基于SWAN模式和折绕射模式的近岸海浪数值模拟

基于SWAN模式和折绕射模式,本文对台湾海峡和平潭岛附近海域的海浪要素进行数值模拟。首先通过SWAN模式得到实时预报的高时空分辨率的波高、周期和波向等海浪要素数据,为折绕射模型提供波浪边界,进而对重点海区近岸波浪进行折绕射计算,最后对数值预报结果进行统计检验及预报分析。经过验证,预报结果与实测数据基本一致,预报效果较好。研究成果可为平潭海浪预警报业务提供技术支撑,也可为海浪灾害应急管理及沿海规划等提供参考依据。     

波浪谱形对不规则波数值模拟的影响

通过数值模拟分析了波浪谱形对不规则波浪数值模拟结果的影响.采用不同参数的JONSWAP谱模拟入射波要素,基于抛物型缓坡方程模拟不规则波浪的传播,分析了波浪谱形状对波浪数值模拟结果的影响.结果表明,采用抛物型缓坡方程模拟不规则波浪时,入射波浪谱形对模拟结果影响不明显;但由于模型中非线性项的影响,采用不规则波模拟的波高分布和采用规则波模拟的结果略有差别.     

Microbial Biomass and Organic Nutrients in the Deep-Sea Sediments of the Central Indian Ocean Basin

In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance.     

Assessing the Validity of Seismo-Acoustic Predictor Equations for Obtaining Seabed and Sub-Surface Sediment Physical Properties

The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths.     

A Review of Some Environmental Issues Affecting Marine Mining

This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested.     

Increased Particle Fluxes at the INDEX Site Attributable to Simulated Benthic Disturbance

Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement.     

海上大直径钢管桩打桩过程中桩周土强度弱化研究

海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。     

Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification

An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm.     

Determination of In Situ Sediment Shear Strength from Advanced Piston Corer Pullout Forces

The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments.     

Interannual Sea Level Variations and Annual Tides in the Northwestern Pacific

Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone.     

《Acta Oceanologica Sinica》Vol. 33(2014) contents

<正>~~