基于高程统计方法的机载LiDAR点云数据滤波

提出了一种基于高程统计的LiDAR数据滤波方法,该方法以高程分布统计量为依据,通过迭代的方法逐个滤除,是一种基于原始点云的非监督滤波算法。采用北京凤凰岭地区某块机载LiDAR数据进行实验,并做出了实验改进。实验表明,该方法能够准确有效地滤除地物点,既能较好地保持数据信息量与精度,又不依赖于其他数据源,是一种简单有效的滤波算法。     

联立偏度与峰度变化曲线的机载LiDAR点云滤波方法

针对经典滤波算法易受参数、阈值选取影响以及传统偏度平衡方法滤波结果不理想等问题,提出一种联立偏度与峰度变化曲线的机载LiDAR点云二次滤波方法。该方法不受参数与阈值选取影响,在联立初始LiDAR点云二者基础上,通过在其变化曲线上寻找最优偏度平衡点完成一次滤波;然后对初次滤波后获取地面点进行多项式曲面拟合,根据拟合后的高差统计值进行偏度平衡二次滤波。实验结果表明:该方法能保证变化很小的前提下,减少和总误差,滤波效果更好。     

一种从城区LiDAR数据提取DEM的方法

机载激光扫描系统可以直接生成扫描区域的数字表面模型,但为了提取数字地面模型还须对LiDAR数据进行滤波处理。分析用坡度法对机载LiDAR数据进行滤波的不足,针对其不足以及城区LiDAR数据的特点,提出一种将坡度法与区域增长相结合的滤波方法。与坡度法相比,该方法提高了滤波的精度和效率,并能对复杂的城市地貌进行滤波。试验结果表明,该方法计算速度快,并能够有效地滤除城区LiDAR数据中的地物。     

基于参数统计的LiDAR数据分割算法

假设自然地表分布连续,在地形起伏不大的情况下,局部地表的高程值具有正态分布的特点,而地物点的存在往往会破坏正态分布的平衡性。基于这种思想文中引入两个反映正态分布特点的统计量：偏度和峰度,设计了基于参数统计的LiDAR分割算法。该方法无需事先设定阈值,实施简单方便,不仅适用于格网形式LiDAR数据,也可用于离散分布的激光脚点。     

面向滩涂DEM构建的机载LiDAR点云滤波方法

在基于激光点云构建DEM的过程中,用于区分地面点和非地面点的点云滤波处理至关重要。本文面向基于机载LiDAR点云的沿海滩涂DEM高精度的构建需求,提出了一种机载LiDAR点云的改进坡度滤波算法。首先,采用统计异常值剔除法(SOR)去除原始机载LiDAR点云数据中的噪声;然后,利用规则格网的坡度和高程阈值,设计了适用于滩涂点云数据的地面点坡度滤波方法;最后,选取如东市长沙港的滩涂机载LiDAR点云作为试验数据,构建滩涂DEM,并进行精度检验。试验结果表明,利用本文方法处理后的LiDAR点云构建的DEM精度满足国家与行业标准的要求。     

基于TIN的LiDAR数据滤波算法研究

研究利用区域生长滤波算法将原始激光点云数据直接构建不规则三角网(TIN),并选择地面最低高程点作为初始种子点,根据设定的高差阈值对种子点的邻域进行区域生长滤波处理。通过对试验区机载LiDAR点云数据的滤波处理结果与基于坡度滤波和基于移动窗口的高程滤波算法进行对比分析,结果显示该方法具有一定的优越性。     

基于地形变化检测的机载LiDAR滤波方法

LiDAR滤波是从其数据中提取数字地形模型(DTM)的一个主要步骤。当前的LiDAR滤波方法大都是通过单一的LiDAR点云数据来进行的,由于点云缺乏真实数据作参考,在滤波时可能会出现较大的误差。因此,提出一种基于地形变化检测的机载LiDAR滤波方法。首先将LiDAR点云数据与已有的DEM数据精确配准并统一到同一坐标系下,然后对LiDAR点云数据进行格网化组织,使LiDAR点云数据与DEM数据中相应的区域对应,最后把已有的DEM数据与LiDAR点云数据叠加进行滤波。为了验证该方法,采用城区和山区2种不同地形特点的数据分别进行试验。结果表明该方法能有效滤除城市和山地环境中的地物,并且保留地形的细节信息。     

一种顾及地形复杂度的LiDAR点云多尺度滤波方法

针对复杂地形区域的机载LiDAR数据滤波方法中自适应阈值设置问题,根据地形多尺度效应,提出一种自适应阈值的机载LiDAR点云多尺度滤波方法。该方法采用影像金字塔策略按分辨率从高至低逐级构建LiDAR点云分层格网,滤波过程则从最大尺度格网(顶层格网,最低分辨率)开始,采用局部统计分析的方法自适应地确定高差阈值,同时结合薄板样条内插出下层各格网控制点的高程值,直至最底层格网完成原始激光点云滤波。通过我国某山区城市复杂地形的LiDAR数据实验表明顾及地形复杂度的LiDAR点云多尺度滤波方法能够快速有效地提取高精度DEM,能够满足实际生产需求。     

基于渐进三角网的机载LiDAR点云数据滤波

机载LiDAR点云数据滤波是获取高精度数字高程模型的关键,也是目前LiDAR点云数据处理领域研究的重点和难点之一。提出了基于渐进三角网的机载LiDAR点云数据滤波方法,首先以规则格网和不规则三角网组织数据,采用区域分块法或数学形态学法选取种子地面点建立初始稀疏三角网,通过不断向上加密三角网提取地面点。试验结果表明,该算...     

基于模糊C均值聚类的机载LiDAR点云滤波

点云滤波是机载LiDAR数据处理的重要步骤.现有滤波算法大部分要建立点云之间的索引关系,增加了算法的复杂度;或需要对原始数据进行内插,导致原有精度损失.本文在对LiDAR点云数据的高程进行统计分析的基础上,引入模糊C均值聚类分析算法,针对大区域平坦复杂城区数据,无须建立索引或进行内插,能够快速简单地实现地面点与非地面点的分类.实验结果表明,该方法切实可行,能够较好地满足精度需求.     

阿克苏河-塔里木河水系水质污染遥感监测与评价

 采用Landsat TM数据分析了阿克苏河—塔里木河断面水质污染状况,通过波段的DN值和常规监测数据建立能反映水质状况的 污染物监测模型。结果发现,将2000年常规监测数据代入模型后,与遥感数据的结果基本吻合| 重建阿克苏河—塔里木河的连续水体 污染变化曲线,得出污染物浓度随着远离上游而增加。     

Monitoring drought dynamics in the Aravalli region (India) using different indices based on ground and remote sensing data

The hard-rock hilly Aravalli terrain of Rajasthan province of India suffers with frequent drought due to poor and delayed monsoon, abnormally high summer-temperature and insufficient water resources. In the present study, detailed analysis of meteorological and hydrological data of the Aravalli region has been carried out for the years 1984–2003. Standardised Precipitation Index (SPI) has been used to quantify the precipitation deficit. Standardised Water-Level Index (SWI) has been developed to assess ground-water recharge-deficit. Vegetative drought indices like Vegetation Condition Index (VCI) and Temperature Condition Index (TCI) and Vegetation Health Index (VHI) have been computed using NDVI values obtained from Global Vegetation Index (GVI) and thermal channel data of NOAA AVHRR satellite. Detailed analyses of spatial and temporal drought dynamics during monsoon and non-monsoon seasons have been carried out through drought index maps generated in Geographic Information Systems (GIS) environment. Analysis and interpretation of these maps reveal that negative SPI anomalies not always correspond to drought. In the Aravalli region, aquifer-stress shifts its position time to time, and in certain pockets it is more frequent. In comparison to hydrological stress, vegetative stress in the Aravalli region is found to be slower to begin but quicker to withdraw.     

使用FME与VBA提取机场方格网高程数据

因受机场工程设计软件的测量数据容量限制,基于LiDAR采集、点云分类后得到的地面点云数据LAS不能完整应用于目前设计软件进行设计计算。本文通过对拟选技术方案的筛选,提出了利用FME Workbench数据处理功能,结合VBA编程获取外部方格网平面数据的方法。该方法在FME Workbench中实现了地面点云数据构建TIN、采用逐点内插方法从TIN中提取方格网高程数据、等高线生成及相应图形处理与成果输出。最终通过实际算例证明了该方法的有效性。     

Landslide risk analysis between Giri and Tons Rivers in Himachal Himalaya (India)

The area around Sataun in the Sirmur district of Himachal Pradesh, India (falling between the rivers Giri and Tons; both tributaries of the Yamuna River) was studied for landslide vulnerability on behalf of the inhabitants. The study was made using extensive remote sensing data (satellite and airborne). It is well supported by field evidence, demographic and infrastructural details and aided by Geographic Information System (GIS) based techniques. Field observations testify that slope, aspect, geology, tectonic planes, drainage, and land use all influence landslides in the region. These parameters were taken into consideration using the statistical approach of landslide hazard zonation. Using the census data of 1991, vulnerability of the populace to the landslide hazard was accessed. As most of the infrastructure in the region is concentrated around population centres, population data alone was used for vulnerability studies.     

Gravity Changes Before Large Earthquakes in China: 1998-2005

Although it is well known that coseismic gravity changes take place during an earthquake, previous research has not yielded convincing evidence demonstrating that significant gravity changes occur before large earthquakes. Furthermore, even if we suspect that gravity changes occur before large earthquakes, we have yet to demonstrate how to consistently observe these changes for useful earthquake forecast that would bring benefits to society. We analyzed ground gravity survey data obtained in 1998, 2000, 200...     

GNSS系统及其技术的发展研究

阐述了国际上卫星导航系统的总体发展,对美、俄、欧、中的四大全球系统,以及相关的区域系统和增强系统进行了简单的介绍,研究分析了GNSS系统及其技术的发展趋势,同时分析了我国Compass全球系统面临的机遇和挑战,并提出了我国未来工作的建议.     

“4D”技术及其应用

介绍“４Ｄ”（即数字地面模型、数字正射影像、数字栅格地图和数字线划地图）系列产品的生产流程、关键技术、及其在耕地保护、防灾减灾救灾和城市规划等方面的应用方法。     

Virtual Australia: its key elements – know,think, communicate

Abstract

Virtual Australia is not a well-defined or agreed concept. This discussion paper conceptualises Virtual Australia as a ‘virtual [digital] model containing and representing all non-trivial objects and their contextual environment – from blue sky to bedrock – in real world Australia’. It describes a scenario for Virtual Australia, one or two decades from now, in which the locations and conditions of non-trivial objects and their environment are updated automatically through a combination of remote sensing and wireless communication technologies in support of a ‘Supranet’. It then examines the concept of the ‘Supranet’ – a pervasive information network based largely on wireless technology linking the physical world to a virtual model in real time – and develops and discusses three principal characteristics of the Supranet: the ability to have or collect specific information (know); the ability to process information (think); and the ability to communicate that information. If, in the near future, any or all non-trivial devices are to some extent able to know, think and communicate, the potential for object autonomy will be realised.     

自动车辆定位导航系统中传感器的误差分析

对国界定位导航系统中几种常见的辅助传感器所产生的误差进行了分析，导出了不同传感器的误差模型。这些误差模型是估计车辆位置的扩展卡尔曼滤波器的基础，同时也为选择适当的传感器提供了理论根据。