Simplified DMT-based methods for evaluating liquefaction resistance of soils

This paper presents simplified dilatometer test (DMT)-based methods for evaluation of liquefaction resistance of soils, which is expressed in terms of cyclic resistance ratio (CRR). Two DMT parameters, horizontal stress index (K_D) and dilatometer modulus (E_D), are used as an index for assessing liquefaction resistance of soils. Specifically, CRR–K_D and CRR–E_D boundary curves are established based on the existing boundary curves that have already been developed based on standard penetration test (SPT) and cone penetration test (CPT). One key element in the development of CRR–K_D and CRR–E_D boundary curves is the correlations between K_D (or E_D) and the blow count (N) in the SPT or cone tip resistance (q_c) from the CPT. In this study, these correlations are established through regression analysis of the test results of SPT, CPT, and DMT conducted side-by-side at each of five sites selected. The validity of the developed CRR–K_D and CRR–E_D curves for evaluating liquefaction resistance is examined with published liquefaction case histories. The results of the study show that the developed DMT-based models are quite promising as a tool for evaluating liquefaction resistance of soils.     

The consolidation characteristics of an unsaturated compacted soil

The compacted soils are extensively employed as mineral liners or a sealing system, constructed under municipal solid waste and other containment hazardous materials to prevent or minimize the leakage of pollutant liquids and gases into ground water and sublayers. This article presents a detailed experimental study on settlement characteristics, which are required for the construction of a sealing system. For the experimental study where a compacted unsaturated soil taken from Adana in Turkey has been used, a special equipped consolidation cell has been designed and constructed. The matric suction adopted as independent stress-state variables has been controlled by using the axis translation technique. The consolidation tests have been performed under constant matric suction. Furthermore, the pressure plate tests for various net vertical stresses have been conducted. The test results have indicated that the settlement characteristics of a compacted soil as mineral liners and covers are highly affected by matric suction. The water retention capacity of mineral liners, an important factor for hydraulic conductivity, also changes with the vertical load. The compressibility decreases as the matric suction increases. It has been observed that there exists an exponential relationship between the compressive indexes (C _t, D _t) and matric suction.     

Some investigations to quantify hysteresis associated with water retention behaviour of fine-grained soils

The soil water retention characteristics curve (SWRC) has been reported to be quite useful for estimation of unsaturated soil properties. However, the uniqueness of SWRC is questionable due to hysteresis associated with the drying- and wetting-path SWRCs and this poses great challenge in utilising the SWRC for reliable estimation of unsaturated soil properties. Although hysteresis associated with SWRCs has been extensively studied for coarse-grained soils, due to limited studies on wetting-path SWRC for fine-grained soils, the hysteresis for fine-grained soils is not well understood. The present work attempts to address this gap, by studying the drying- and wetting-path SWRCs for eight different fine-grained soils by employing Dew point Potentiameter (WP4C®), Environmental Chamber and Controlled Water Sprinkling method. The study employs the concept of ‘Suction Hysteresis’, ψ_h, for quantification of hysteresis. Further, the influence of various soil-specific properties on the variation of ψ_h-water content relationship (viz., slope of variation of suction hysteresis, S_ψh) has also been studied and demonstrated. The findings of the study are quite encouraging and it has been realised that extensive studies on soils of different characteristics would be quite useful in quantifying the variation of SWRC during drying and wetting cycles.     

Cavity expansion in unsaturated soils exhibiting hydraulic hysteresis considering three drainage conditions

Cavity expansion theory assists in the interpretation of in situ tests including the cone penetration test and pressuremeter test. In this paper, a cavity expansion analysis is presented for unsaturated silty sand exhibiting hydraulic hysteresis. The similarity technique is used in the analysis. The soil stress–strain behaviour is described by a bounding surface plasticity model. Results of oedometric compression tests, isotropic compression tests and triaxial shear tests for both saturated and unsaturated states are used to calibrate the model. The void ratio, suction, degree of saturation and effective stress are fully coupled in the analysis. The influence of where the initial hydraulic state is located on the soil–water characteristic curve on the cavity wall pressure is investigated and found to be significant. Also, the effects of three different drainage conditions (constant suction, constant moisture content and constant contribution of suction to the effective stress) on cavity wall pressure are studied. It is found that the drainage condition in which the contribution of suction to the effective stress is constant offers a good approximation to the other two. This may simplify interpretation of in situ tests. When testing occurs quickly, meaning a constant moisture content condition prevails, a constant contribution of suction condition can be assumed without loss of significant accuracy. The contribution of suction assumed in the interpretation can be taken as being equal to the in situ value, although this discovery may not be applicable to all soil types, constitutive models and soil–water characteristic curves. Copyright © 2015 John Wiley & Sons, Ltd.     

Analytical solution to 1D coupled water infiltration and deformation in two‐layer unsaturated soils

An analytical solution to 1D coupled water infiltration and deformation in layered soils is derived using a Laplace transformation. Coupling between seepage and deformation, and initial conditions defined by arbitrary continuous pore‐water pressure distributions are considered. The analytical solutions describe the transient pore‐water pressure distributions during 1D, vertical infiltration toward the water table through two‐layer unsaturated soils. The nonlinear coupled formulations are first linearized and transformed into a form that is solvable using a Laplace transformation. The solutions provide a reliable means of comparing the accuracy of various numerical methods. Parameters considered in the coupled analysis include the saturated permeability (k_s), desaturation coefficient (α), and saturated volumetric water content (θ_s) of each soil layer, and antecedent and subsequent rainfall infiltration rates. The analytical solution demonstrates that the coupling of seepage and deformation plays an important role in water infiltration in layered unsaturated soils. A smaller value of α or a smaller absolute value of the elastic modulus of the soil with respect to a change in soil suction (H) for layered unsaturated soils means more marked coupling effect. A smaller absolute value of H of the upper layer soil also tends to cause more marked coupling effect. A large difference between the saturated coefficients of permeability for the top and bottom soil layers leads to reduced rainfall infiltration into the deep soil layer. The initial conditions also play a significant role in the pore‐water pressure redistribution and coupling effect. Copyright © 2011 John Wiley & Sons, Ltd.     

Analytical solution to 1D coupled water infiltration and deformation in unsaturated soils

An analytical solution to 1D coupled water infiltration and deformation is derived using a Fourier integral transform. Exponential functional forms are used to represent the hydraulic conductivity–pore‐water pressure relationship and the soil‐water characteristic curve. Fredlund's incremental‐linear constitutive model for unsaturated soils is adopted. The analytical solution considers arbitrary initial pore‐water pressure distributions and flux and pressure boundary conditions. The corresponding analytical solutions to coupled steady‐state problems are also obtained. The analytical solutions demonstrate that the coupling of seepage and deformation plays an important role in water infiltration in unsaturated soils. In the early stages of infiltration, the difference between uncoupled and coupled conditions becomes marked over time, and in late stages, the difference caused by the coupling effects diminishes toward the steady state. The difference between the uncoupled and coupled conditions increases with decreasing desaturation coefficient (α). Pore‐water pressure or deformation changes caused by the coupling effects are mainly controlled by the degree of soil volume change due to a change in soil suction (H). The smaller the absolute value of H, the greater the effect of coupling on the infiltration and deformation. The ratio of rainfall intensity to saturated permeability (q/k_s) also has a strong influence on the coupled seepage and deformation. Copyright © 2008 John Wiley & Sons, Ltd.     

Effects of water and fines contents on the resilient modulus of the interlayer soil of railway substructure

This paper deals with the resilient behavior of the interlayer soil which is created mainly by the interpenetration of ballast and subgrade soils. The interlayer soil studied was taken from a site in the southeast of France. Large-scale cyclic triaxial tests were carried out at three water contents (w = 4, 6 and 12 %) and three fines contents corresponding to 5, 10 % subgrade added to the natural interlayer soil and 10 % fine particles (<80 μm) removed from the natural interlayer soil. Soil specimens underwent various deviator stresses, and for each deviator stress, a large number of cycles was applied. The effects of deviator stress, number of cycles, water content and fines content on the resilient modulus (M _r) were analyzed. It appears that the effects of water content and fines content must be analyzed together because the two effects are closely linked. Under unsaturated conditions, the soil containing high fines content has higher resilient modulus due to the contribution of suction. When the soil approaches the saturated state, it loses its mechanical enhancement with a sharp decrease in resilient modulus.     

Predicting effective stress parameter of unsaturated soils using neural networks

In the effective stress equation for unsaturated soils proposed by Bishop, shear strength in these soils depends on the effective stress parameter, χ, a function of soil suction [1]. To estimate the shear strength of unsaturated soils, one must already know this parameter and its variation with soil suction. Though theories on the shear strength of unsaturated soils are consistent with experimental measurements, estimating the effective stress parameter directly from tedious laboratory tests is impractical. Thus, researchers have performed numerous intensive studies to effectively obtain the unsaturated shear strength using simplified empirical methods.This paper shows an adaptive learning neural network method for predicting this parameter, χ. The proposed network is a multilayer perceptron network with six neurons in the input layer representing the air entry value, the volumetric water content at residual and saturated conditions, the slope of soil water characteristic curve, the net confining stress and suction. The available literature uses a database prepared from triaxial shear test results to train and test the network. The results show the suitability of the proposed approach for estimating the effective stress parameter. Network analysis indicates that the χ-parameter depends strongly on the net mean stress.     

水膜理论在非饱和土中吸力的应用研究

非饱和土中总吸力问题一直是非饱和土土力学研究的一个重要分支。本文引用并引伸了水膜理论,把水膜理论的水膜范围扩展到包括结合水和毛细作用及基质吸力等引起的自由水（重力水）等部分,相应的水膜分离压也包括基质吸力和毛细作用,因此,非饱和土中的总吸力相应地可表示为扩展后的水膜分离压。从广义水膜理论及土性方面分析非饱和土总吸力,探讨了非饱和土中水膜对总吸力的影响,导出了广义非饱和土水膜理论下的总吸力公式,给出了非饱和土总吸力当土颗粒大小不同时与饱和度的关系。理论计算与试验结果吻合较好,表明了广义水膜理论对研究非饱和土总吸力具有一定的指导意义。     

粉土基质吸力的新型量测装置与土-水特征研究

以非饱和土张力计原理为基础,制作了一种新型的基质吸力量测装置,并通过实测过程的不断总结与改进,得到了一种成本低廉、制作简单、操作便利、试验快速和结果可靠的非饱和土基质吸力量测装置,以此装置测定了不同体积含水率、不同压实度和干湿循环后粉土的基质吸力变化规律,得到了不同压实度粉土的土-水特征曲线,并通过Origin软件中的Boltzmann模型进行拟合对比分析,得到了与压实度相关的土-水特征曲线,比较了不同压实度粉土的含水率变化对基质吸力的不同影响特点。试验结果表明,干湿循环对粉土的基质吸力和强度有很大影响。     

Transfer of moisture through the unsaturated zone in the tropical forest using the neutron probe

Knowledge of moisture content is crucial in assessing spatial and temporal movement of water through the unsaturated zone. Moisture storage is also important for monitoring the soil water balance and for validation of water balance models. The purpose of this work was to determine and analyse moisture content profiles at point locations in the unsaturated zone of a lateritic soil around Nsimi, south of Cameroon. Neutron probe has been connected to a set of tensiometers in an area of 60 ha. A comparative study between a site covered with vegetation and a site uncovered was conducted to assess the influence of vegetation in the process of moisture transfers. The results showed that the spatial distribution of moisture profiles varied according to the site and the texture of the soil, with in general increasing of moisture from the surface horizon toward the deeper layers. The mean values of moisture varied fromθ_m = 0,397 cm³/cm³ on barren site, against 0 = 0,429 cm³/cm³ in vegetation. Values of suction were generally strong in surface and at depth, but weak in the intermediate layers.     

Solute transport as affected by surface land characteristics in gravely calcareous arid soils

Gravely calcareous soils cover approximately most of arid lands (in percent); however, the solute transport behavior in these soils remains a current issue. This research aimed at estimating and correlating the solute transport parameters in gravely calcareous soils as being affected by different land uses through the knowledge of the soil morphological, physical, and chemical properties. Four different land use sites were selected: irrigated trees and bare, range, and alluvial sediment lands. Solute transport parameters of soil pore water velocity (V), dispersion coefficient (D), and retardation factor (R) were estimated using bromide breakthrough curve tests for surface soil columns. In addition, field Brilliant Blue FCF dye tracing experiment was conducted to determine the maximum dimensional movements. Soil morphological analysis was able to explain the heterogeneity in the solute transport parameters. Conductive solute transport mechanism with V of 17.99 m/day was favored in a high continuous pore system observed under tree lands. Presence of high gravel and CaCO₃ contents under range lands increased pore system tortuosity and thus increased D magnitude up to 1,339.88 cm²/day. Existence of thin surface crusts at both bare soils and alluvial sediments had considerably restricted V down to 1.46 m/day. Dye staining technique aided the explanation of the existing variations by providing visual evidence on the preferential flow paths and patterns governing the solute transport mechanism at each site.     

非饱和填土侧限压缩变形特性试验研究及应用初探

为研究吸力及压实度对非饱和压实填土压缩变形特性的影响,并建立脱湿（吸力增长）状态下的填方土体工后沉降变形修正计算应用模型,开展了控制吸力和压实度的一维非饱和土侧限压缩试验。结果表明：压缩曲线平缓段随压实度和吸力的提高而增长,表明土样的结构屈服强度同步得到提高;在比容v变化差值序列上,饱和土压缩土样最大、常规压缩土样次之、脱湿土样最小,并且吸力越大,比容v变化差值越小。经历脱湿（吸力增长）后的压实土压缩性降低,定义和建立了吸力压缩系数 及其经验模型,用以表征和度量吸力和压实度对压缩特性的影响规律及程度,发现 随竖向应力增加呈现指数型衰减。对模型参数与压实土相关参量间的关联性进行了分析探讨,同一压实度土样不同吸力所对应的参数 均值随压实水平提高而线性减小,参数λ总体上随吸力的增加而增大,但随压实度的提高吸力对于土体抗压性增强的贡献水平降低且参数 试验数值点靠拢线性趋近线,土样的压缩性随压实度和吸力大小变化而动态调整。基于分层总和法的基本原理初步构造建立了高填方非饱和填土压缩变形修正计算模型（MS）,其应用途径应建立在进一步对非饱和压实填土受荷状态下脱湿土-水特征关系的研究基础之上。     

Spatial pore characteristics of unsaturated soils caused by dielectric geometric factors under permittivity method with 1 GHz frequency range

A dielectric measurement device called a frequency domain reflectometry (FDR) has been designed and constructed for the dielectric measurement of unsaturated soil consisting of a volumetric soil water content of about 0.1, 0.2, and 0.3 m³/m³ with different soil porosity around 0.40–0.45, respectively. The dielectric constant is measured in the frequency range 1 GHz. Soil calibration tests and tracer injection tests on standard sand and river sand are carried out in the laboratory. FDR measurement probes at different soil depths allow volumetric soil water content and dielectric constant measurements. The tracer concentration in the pore water is monitored by determining the dielectric constant, from the soil impedance. From the relationship between volumetric soil water content and dielectric constant, the specific calibration equations for the unsaturated soils were derived, and one can easily estimate the volumetric soil water content from the response of the measured dielectric constant for the soils. In the study of dielectric mixture models using α-value of 0.5 which is dielectric geometric factor, the effective porosity for the soils was computed to a range of 87–92% compared with the soil porosity.     

Bearing capacity of unsaturated expansive soils

It is difficult to determine the bearing capacity of a foundation in unsaturated expansive soil, although this is most important. The bearing capacity of unsaturated expansive soil is related to the drying and wetting environment. Swelling pressure occurs when the soil volume change is constrained as an expansive soil is inundated. The expansive lateral pressure, induced by the swelling pressure is similar to the passive earth pressure. By considering the effect of the expansive lateral pressure in Terzaghi's bearing capacity formula, the bearing capacity of unsaturated expansive soil is derived. Because it is very difficult to measure suction in situ, the bearing capacity is expressed using the expansive lateral pressure offers a feasible approach to calculate the bearing capacity of a foundation in unsaturated expansive soil, when suction is not measured. Plate load tests to measure the bearing capacity in situ were performed for the foundation in natural soil and saturated soil immersed by water. The verification of the bearing capacity formulae presented in this paper is conducted by comparing the predicted results with the results of the plate load tests on unsaturated expansive soils in Handan and Bingxia, China.     

Slip line theory applied to a retaining wall–unsaturated soil interaction problem

An extension of slip line theory to unsaturated soils is presented and applied to the problem of a rigid retaining wall rotating about its toe into unsaturated soils. Suction is introduced using the effective stress concept. Soil–wall interface friction is defined carefully. The influence of suction on limiting passive earth pressures is analysed for two soils under steady state evaporation and infiltration. Suction increases the limiting passive stress at the soil–wall interface, with a dependence on the steady state flow type. The displacement of the retained soil is studied assuming the wall undergoes a rotation increment. The results show a clear difference in the displacement for evaporation and infiltration.     

A bounding surface model for unsaturated soils considering the microscopic pore structure and interparticle bonding effect due to water menisci

The interparticle bonding effect due to water menisci plays an important role in the hydromechanical coupling properties of unsaturated soils. This paper presents an unsaturated hydromechanical coupling model that considers the influence of matric suction, degree of saturation, and microscopic pore structure on the interparticle bonding effect. The enhanced effective stress and bonding variable are selected as constitutive variables. The bonding variable is correlated with the ratio between unsaturated void ratio and saturated void ratio. The deformation characteristics of unsaturated soils are described based on the bounding surface plasticity theory. A soil–water characteristic model that considers deformation and hydraulic hysteresis is integrated into the constitutive model to achieve hydromechanical coupling. The proposed model can effectively describe the hydromechanical coupling characteristics and the meniscus bonding force of unsaturated bimodal structure soils; the model parameters can be easily obtained through routine experiments. The experimental results of unsaturated isotropic compression, the wetting/drying cycle, and unsaturated triaxial shear tests are used to validate the capability of the proposed model.

     

不同类型黏土的强度特性及其预测

强度特性是非饱和土力学中基础性的研究内容。目前对广吸力范围内非饱和黏土强度的预测研究相对较少。本文首先基于文献中粉质黏土、Madrid黏土和南阳弱膨胀土的非饱和强度特性进行了对比与分析。将不同类型非饱和黏土的强度特性大致分为3种类型:（1）在某一吸力范围试样出现强度峰值,并随着吸力值的进一步增大而降低;（2）达到某一吸力值后其强度几乎维持不变,不受吸力值的影响;（3）其强度随着吸力值的增大而增大。此外,基于现有考虑吸附水膜和毛细水作用的方法拟合广吸力范围内不同类型土的土水特征曲线,并将土水特征曲线分离成吸附土水特征曲线和毛细土水特征曲线。在非饱和土的抗剪强度公式中,认为吸力引起的非饱和强度增强部分主要由毛细水作用决定的,故将非饱和抗剪强度公式中吸力引起非饱和增强项的有效应力系数（即饱和度或有效饱和度）用毛细水对应的饱和度替代。最后,利用修正后的非饱和抗剪强度公式对3种较广吸力范围内非饱和土的强度进行了预测。预测结果表明过渡区段内的强度预测效果较好,但高吸力段非饱和强度的预测还有待进一步研究。     

Comparison of testing techniques and models for establishing the SWCC of riverbank soils

The soil water characteristic curve (SWCC), also known as soil water retention curve (SWRC), describes the relationship between water content and soil suction in unsaturated soils. Water content and suction affect the permeability, shear strength, volume change and deformability of unsaturated soils. This paper presents results of the laboratory determination of the SWCC for soil samples obtained from the riverbank of the Lower Roanoke River in North Carolina. Six different testing methods were used to establish the SWCC including the filter paper, dewpoint potentiameter, vapor equilibrium, pressure plate, Tempe cell and osmotic methods. It is concluded that each suction measurement technique provides different measurable ranges of suction values, and the combined results from the different tests provide continuous SWCCs. Three widely available models were also shown to adequately fit the experimental SWCC data, particularly for matric suction values under 1500 kPa. These results will be valuable to practitioners in deciding which methods to use to establish the SWCC, and which empirical relationship to use for modeling the SWCC of riverbank soils.     

Influence of different strain rates on hydro-mechanical behaviour of reconstituted unsaturated soil

The hydro-mechanical behaviour of a reconstituted unsaturated soil under different suctions and strain rates was studied through various rate-controlled unsaturated/undrained triaxial tests. The fully saturated reconstituted specimens were desaturated to four different initial suctions (s₀?=?0, 100 kPa, 200 kPa and 300 kPa) and then triaxially sheared (conventional triaxial compression) at three different strain rates in undrained conditions (\(\dot{\varepsilon }_{1} = 0.001\) h^?1, 0.01 h^?1, and 0.1 h^?1). The observed hydro-mechanical behaviour during shearing including the volumetric strain, deviatoric stress, degree of saturation and suction is presented and discussed in this paper. The results indicate that when the strain rate rises at the given initial suctions (or pore water pressures), the maximum deviatoric stress (q_max), critical net stress ratio (M) and critical state suction (s_c) increase but the degree of saturation (S_rc) and volumetric strain at the critical state (ε^c_v ) reduce. The critical effective stress ratio (M′) is not dependent on the strain rate for saturated and unsaturated samples. The critical state lines for unsaturated soils with the constant strain rates are parallel with each other in the e???lnp′ space.