新型多立柱式Spar平台涡激运动特性研究

通过数值模拟和模型试验方法对一新型的Spar平台——多立柱式Spar平台的涡激运动特性进行研究。平台硬舱为四根圆柱方形阵列布置加方形中心井的形式,各柱间会产生复杂的相互干扰,不同于常规的单立柱Spar平台或半潜式平台,因此对其开展相应的涡激运动研究具有重要意义。研究主要关注的是不同来流角、不同流速下平台的涡激运动特性。通过涡激运动时的横荡运动、水平面内运动轨迹、首摇运动和水动力系数及绕流流场的分析,可得:在折合速度约为6~8范围内,平台横荡运动存在明显的“锁定”现象(0°来流角无侧板时“锁定”范围约为Ur=7~10)。在0°来流角下较高流速时,减涡侧板对涡激运动有明显的抑制效果。平台的运动轨迹近似与平台硬舱截面的对角线平行(0°来流角除外),这不同于常规的单立柱Spar平台。此外,试验中还观察到较明显的首摇运动。涡激运动时各柱间绕流存在复杂的相互干扰,而在柱后形成共同的涡结构。     

立柱直径比对四立柱平台涡激运动性能影响的数值研究

与单立柱平台(Spar)类似,四立柱平台在洋流作用下也容易发生涡激运动,对锚泊和立管系统的疲劳寿命产生不利影响。一种非对称半潜式平台具有两种不同尺寸的立柱,立柱直径比对非对称平台涡激运动性能的影响尚需深入研究。采用计算流体力学(CFD)方法,对直径比分别为1.0、1.5和2.0的立柱组合在两种不同角度水流作用下的运动响应进行了二维数值模拟,分析发现:立柱直径比不为1时四立柱平台也具有明显的涡激运动,其横荡运动具有显著的锁定现象;在广义折合速度定义下,与相同直径的四立柱平台相比,立柱直径比不为1时其横荡运动锁定区间变宽且滞后,横荡响应幅值的峰值具有明显差异;在所研究的直径比范围内,大直径立柱在上游时涡激运动响应比其在下游时更显著,且这种差异随着直径比变大而变大。     

均匀流中深水系泊Truss Spar平台涡激运动试验研究

在工程中广泛应用的Truss Spar平台自诞生之初就为涡激运动问题所困扰,对其运动特性及抑制方法的机理性研究始终都在进行。采用截断系泊系统水池模型试验对设计中的Truss Spar平台在均匀流中的涡激运动响应进行了研究,分析了有无侧板平台的运动轨迹以及不同速度及流向角来流对平台运动的平衡位置的影响。在影响平台涡激运动特性的重要因素中,选取折合速度及流向角分别加以研究,分析了幅值在锁定区间中的变化规律,验证了减涡侧板对涡激运动良好的抑制作用,并对热点问题进行了探讨。为进一步研究Spar平台的涡激运动特性奠定了基础。     

张力腿平台涡激运动模型试验与数值分析

为揭示张力腿平台涡激运动响应规律,采用数值模拟与模型试验相结合的方法研究了全水深系泊张力腿平台涡激运动响应。根据张力腿平台主尺度参数,按照几何相似制作了水池试验模型,在满足运动相似和动力相似的条件下开展了均匀流、剖面流模型试验,并将模型试验结果与数值模拟结果进行了对比,验证了数值模拟与模型试验结果的一致性。分析结果表明在均匀流作用下张力腿平台涡激运动的锁定区间在5.5<U_r<8.5,来流角对涡激运动影响较大。剖面流作用下平台涡激运动规律与均匀流作用基本一致,但剖面流造流引起的能量分散,使平台在XY平面的运动轨迹变得不规律,系泊系统提供的回复力对涡激运动幅值有抑制作用,来流角和流速对张力腿或立管模态影响明显。论文得到结论对于张力腿平台的工程设计有一定借鉴意义。     

基于非线性数学模型的半潜式平台共振运动特性研究

共振运动是深海浮式平台设计的关键考虑因素之一,对海洋平台的作业具有重要影响。采用半潜式平台运动的非线性耦合数学模型,考虑浮筒和横撑出入水以及垂荡、横摇和纵摇运动耦合对平台浮力和恢复力的影响,研究半潜式平台非线性共振运动特性,以及不规则波浪参数对运动的影响。研究表明:在非线性耦合运动和浮力变化的影响下,半潜式平台纵摇和垂荡运动的固有周期会随运动幅值的增大而逐渐减小,且最终趋于稳定,对纵摇运动周期的影响更为显著;非线性效应会使半潜式平台产生显著的低频纵摇共振响应,以及共振频率漂移的现象,且受随机种子和波浪周期的影响较小。     

半潜式浮式风机支撑平台首摇运动特性分析

借助FAST软件对OC4半潜式浮式风机平台进行数值计算,分析了影响海上浮式风机平台首摇运动的一系列重要因素及其变化规律(如风向变化、浪向变化、陀螺力矩等)。研究了平台首摇运动所诱导的风机系统动力响应,发现浮式风机首摇运动不仅会加剧平台耦合运动响应,而且还会影响风机的气动性能和加剧锚泊张力波动。提出并探讨了几种减小海上浮式风机支撑平台首摇运动的方法。     

基于SESAM的半潜式平台水动力响应分析

根据三维势流理论,应用SESAM软件对国内某海域半潜式平台的水动力性能进行了研究。分析了目标平台在频域下的附加质量系数、阻尼系数,以及运动响应幅值(RAO)等一系列水动力参数,并研究了粘性阻尼对半潜式平台RAO的影响。结果表明,粘性阻尼对半潜式平台运动响应幅值有很大的影响,研究水动力性能时不能忽略。     

一种新型干树式半潜平台设计

开发了一种新型的深吃水干树式半潜生产平台(TCDD-Semi),该平台可用于中国南海深水区域的油气田开发。它的一个显著特点是立柱的截面形状呈现为渐变形式,而非传统的等截面形式。立柱的底部最大,向上逐渐变小,再结合适当的下浮体设计,能够为平台在服役前期及在位状态时提供足够的浮力以及稳性。最重要的是这种新型立柱的设计能够明显地减小平台在恶劣海况时的垂向运动,从而使在平台上布置具有干式采油树的TTR立管系统成为可能。此外,这种渐变式的立柱设计也有利于减弱平台在流作用下的涡激诱导运动(VIM)。分析结果表明这种渐变式立柱半潜平台可以明显降低平台的垂向运动,也可以在码头组装时提供足够的浮力以及在平台下沉过程中提供足够的稳性。平台优越的垂向运动性能可以使顶部张紧式立管的行程范围限制在10.5 m之内(包括平台偏移、垂荡运动、潮汐影响、海床沉降、热膨胀等因素)。分析结果表明平台的垂荡范围、水平偏移、倾侧角度、上部模块重心处的加速度等可以满足设计要求,证明了这种新型干树式半潜平台的可行性。     

畸形波作用下半潜浮式风机系泊失效停机响应分析

半潜浮式风机逐渐在深海风电开发中受到关注,建立风机、平台与系泊结构耦合数值计算模型,通过FAST与AQWA链接进行风机塔基荷载及平台运动响应相互耦合传递,基于随机波与极限波组合模型生成畸形波时程序列,进行半潜浮式风机系泊失效全过程时域模拟计算分析,得出系泊锚链张力、风机、塔筒和平台运动时程响应,探究系泊失效、风机停机和叶片变桨速率对浮式风机平台系泊结构动力响应的影响。结果表明：畸形波作用下浮式平台和系泊结构动力响应显著,系泊失效导致塔基剪力增加,平台纵荡和纵摇运动响应显著增大;风机停机会引起系泊锚链张力显著减小,转子推力、塔基剪力和叶尖挥舞位移响应逐渐衰减,平台纵荡、纵摇和横摇运动响应显著减小;随着叶片变桨速率增加,风机转子推力和塔基剪力波动幅值增大。     

在平台振荡条件下TLP张力腿的涡激非线性响应

给出了预测张力腿涡激横向振动的时域分析,考虑了波浪、海流、张力腿平台的横漂与垂荡诸因素.张力腿平台的垂荡引起张力周期性变化,对张力腿的涡激横向振动起参数激励的作用,使其动力响应更为复杂.讨论了参数激励下涡激响应的共振条件;以尾流振子模型为基础,发展了分析张力腿在动张力作用下的涡激振动的工程方法,并分析了一座TLP实例,给出了在横漂周期内张力腿上质点的相对位移、弯矩、剪力幅值的时间历程.结果表明,平台垂荡使张力腿的涡激响应幅值升高、高频成分增加,因此它对张力腿的疲劳设计是重要的.     

Assessing the Validity of Seismo-Acoustic Predictor Equations for Obtaining Seabed and Sub-Surface Sediment Physical Properties

The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths.     

A Review of Some Environmental Issues Affecting Marine Mining

This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested.     

Increased Particle Fluxes at the INDEX Site Attributable to Simulated Benthic Disturbance

Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement.     

海上大直径钢管桩打桩过程中桩周土强度弱化研究

海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。     

Determination of In Situ Sediment Shear Strength from Advanced Piston Corer Pullout Forces

The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments.     

Interannual Sea Level Variations and Annual Tides in the Northwestern Pacific

Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone.     

Flow Cytometric Analysis of Coastal Lagoon Bacterioplankton and Picophytoplankton: Fixation and Storage Effects

The effect of different fixation and storage protocols on the flow cytometric (FCM) simultaneous analysis of bacterioplankton and phytoplankton in coastal seawater samples (Mediterranean coastal lagoons) was investigated. FCM measurements (cell number, fluorescence and scatter characteristics) were obtained through DAPI staining. Three fixatives [glutaraldehyde (GA), formaldehyde (FA) and paraformaldehyde (PFA)] and two storage (3 months duration) methods (5 °C and −196 °C) were tested. Two dominant populations were detected in studied samples: bacteria and eukaryotic picophytoplankton. Adding fixatives (2% final concentration) appears necessary to obtain FCM exhaustive counts of all the bacteria and phytoplanktonic cells. This was related to the permeation effect of fixatives which allowed a better DAPI staining of the cells. Maximum fluorescence, i.e. optimal staining of the cells was obtained with FA or PFA, and significant lower fluorescences with GA. Fixed samples stored at 5 °C induced rapid cell loss. Only storage in liquid nitrogen of samples fixed with FA or PFA, allows mid-term (≥4 months) preservation of bacteria or picophytoplankton cell numbers, and limited evolution of DAPI-induced fluorescence and scatter characteristics.     

《Acta Oceanologica Sinica》Vol. 33(2014) contents

<正>~~     

INFORMATION FOR AUTHORS

<正>Acta Oceanologica Sinica(AOS)is a comprehensive academic journal edited by the Editorial Committee of Acta Oceanologica Sinica and is designed to provide a forum for important research papers of the marine scientific community which reflect the information on a worldwide basis.The journal publishes scholarly papers on marine science and technology,including physics,chemistry,biology,