潮汐调和分析方法的探讨

为实现对不等时距潮汐资料的分析,基于Matlab内部函数功能,提出了一种调和分析方法。基于这种方法,分别对大连、北海两个站位1985年的全年等时间间距取样的资料和非等时间间距取样的资料进行了调和分析,结果显示,由等时间距资料和非等时间距资料计算的调和常数基本吻合。对大连、北海两个站位的全年资料进行多个不同时间间距取样分...     

中国近海验潮站长期观测资料的潮汐调和分析

对我国近海厦门、大连、北海、连云港、坎门、汕尾、东方、海口、香港北角、名濑、那霸、吕四、闸坡、石臼所共14个验潮站多年潮汐资料进行了分析。对1 a调和分析结果中的8个分潮(Q1,O1,P1,K1,N2,M2,S2,K2)进一步进行了分离,得到各分潮的调和常数,并和1 a潮汐调和分析中的假定值进行了比较。结果表明,有些分潮存在较大误差。用19 a分析所得的调和常数代替传统1 a分析的假定值,能够提高潮汐分析和预报精度,减小误差。     

南海北部沿岸海域潮汐的调和分析

采用t_tide潮汐分析工具对南海北部的5个验潮站2009年全年的逐时潮高资料进行调和分析,计算出各站的调和常数,评估调和常数的准确性、稳定性,并总结了广东沿岸海域潮汐特征.利用对2009年逐时潮高的调和分析结果对2010年全年的潮高进行预测,将各站预测结果与同时间的实测数据进行全年和分季节进行比较,对预测结果与实测数据的残差进行统计分析.通过对残差的散点分布、概率分布、置信区间等统计结果进行分析,检验预测结果的准确性、稳定性和可靠性.结果表明：广东沿岸海域潮汐是以M2分潮为主,K1、O1、S2为次结合的潮汐机制,采用t_tide潮汐分析工具对南海北部潮高的预测结果与实测数据拟合较好,相位预测准确,潮高预测除在时间序列尾部（年尾）有些许较大的误差外,t_tide工具在南海北部潮汐预报中具有较高的准确性和稳定性.预测残差的整体服从正态分布,残差均值小于10-2m量级,方差最大为0.229 4,最小为0.173 2,95%置信区间长度小于10-2.各站季节分析主要分潮的离散度小于0.04的结果充分证明不同季节的分析区别不明显,3个月资料与整年资料的调和分析结果几乎一致,与所选取的季节资料几乎无关.虽然在预测值中,有极个别的残差将近1 m,但并不足以影响到预测的准确性.     

青岛港潮汐的调和分析与预报

用 T_TIDE 潮汐分析工具对青岛港口2019 年1—12 月逐时潮高资料进行不同时段的调和分析,计算其调和常数,并总结该港口潮汐特征。从 2019 年全年的调和分析结果中选择不同分潮建立调和预报模型,对2019 年1 月的潮高进行预测,通过相对误差、判定系数结果分析,确定最优调和预报模型。结果表明:青岛港口为正规半日潮港,以太阴主要半日分潮 M2分潮为主,其次为太阳主要半日分潮 S₂ 、太阴主要椭率半日分潮 N₂ 、太阴-太阳赤纬全日分潮 K₁和太阴赤纬全日分潮 O₁等分潮;对比不同时间长度的分潮振幅及平均海平面,可知其与用于调和分析的潮位资料长度几乎无关。分潮由5 个增加至24 个可明显改进预报效果,再增加几乎没有改进,故选用24 个分潮为最优的调和预报模型。为验证模型具有良好的实用性,对五号码头的实测潮汐数据进行分析预报,进而可知建立的模型能够较好地预报青岛港附近海域的潮汐变化。     

用于分析主要分潮振幅和迟角季节变化的“分步式”调和分析方法

近年来，研究表明全球部分海域的主要分潮存在季节变化。然而，由于使用传统调和分析方法时，分潮的选取受时间窗长度影响，因此难以准确分析潮汐的季节变化。本文结合长、短时间窗，提出“分步式”调和分析方法，通过理想实验和验潮站实际数据分析验证了该方法的准确性。将新方法与传统调和分析方法加以对比，发现无论潮汐是否存在季节变化，该方法都能更加准确地计算主要分潮各月的振幅和迟角。新方法不仅可用于分析验潮站水位数据，还可用于内潮平稳性和非平稳性特征的研究。     

VAV潮汐分析方法在闸坡验潮站的应用

介绍了一种新的海洋潮汐分析方法--VAV分析方法.该方法通过带通滤波将原始时间域数据转换为频率域数据,再对该频率域数据应用最小二乘法求解得到各分潮调和常数.VAV方法可分析受有色噪音"污染"的数据,允许缺测,并能检测、剔除异常数据,通过多次迭代提高调和常数估算精度,该方法亦可进行浅水分潮分析、潮位预报和海平面变化分析等.利用VAV方法对闸坡验潮站潮位资料进行分析,得到的各主要分潮调和常数、预报潮位及多年平均海平面和多年海平面平均上升速率结果与传统调和分析结果对比基本一致.同时,VAV方法分析得到闸坡站1975-1997年海平面总体呈先降后升趋势,其中1975-1979年为下降期,1980-1997年为上升期.     

运用调和分析方法分离卫星高度计资料中的潮汐信息

针对TOPEX／POSEIDON卫星高度计资料中的潮汐高频混淆现象，采用潮汐调和分析方法，通过比较卫星上、下行轨道交叉点两组资料分析的分潮振幅和分离潮汐后的海面高度；同时比较潮位站实测资料与遥感资料分析的分潮振幅，结果表明：采用潮汐调和分析可以有效地分离高度计资料中的潮汐信息。     

潮汐“波面”分析法

一、引言 本文提出的潮汐分析方法是在半图解法基本原理的基础上发展起来的一种方法。它利用34天的潮汐资料,依据坐标公式在“潮汐波面”上计算出720个非整点的潮高值,对这些潮高值分族后再按照严格的最小二乘法求得75个分潮的调和常数,得到了比较好的结果。     

利用T/P 卫星高度计资料调和分析南海潮汐信息

利用j,v模型调和分析1992～2002年共10 a的TOPEX/Poseidon(T/P)海面高度距平资料,提取了南海K1,O1,P1,Q1,M2,S2,N2和K2等8个主要分潮的潮汐调和常数。分析比较了卫星上下行轨道的19个交叉点的振幅和迟角,其中M2,S2,K1和O1的平均向量均方根偏差分别是1.5,1.1,2.5和1.4 cm;将交叉点的调和常数与TPXO7.2模式的结果进行了比较,结果表明M2,S2,K1和O1分潮振幅的绝对平均误差均小于3 cm,迟角的最大绝对平均误差为7.8°。选取了与卫星轨道较近的8个验潮站,对验潮站的实测数据调和常数和本文所得调和常数进行了比较,结果显示K1分潮的向量均方根偏差为4.7 cm,M2分潮的向量均方根偏差为3.7 cm。论文结果表明利用j,v模型调和分析方法对南海海域卫星高度计资料进行潮汐信息提取是可靠的,并可为局部重力场的研究提供海洋潮汐改正数据,有一定的参考价值。     

潮汐“波面”分析法

本文提出的潮汐分析方法是在半图解法基本原理的基础上发展起来的一种方法。它利用34天的潮汐资料，依据坐标公式在“潮汐波面”上计算出720个非整点的潮高值，对这些潮高值分族后再按照严格的最小二乘法求得75个分潮的调和常数，得到了比较好的结果。     

Microbial Biomass and Organic Nutrients in the Deep-Sea Sediments of the Central Indian Ocean Basin

In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance.     

Assessing the Validity of Seismo-Acoustic Predictor Equations for Obtaining Seabed and Sub-Surface Sediment Physical Properties

The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths.     

海上大直径钢管桩打桩过程中桩周土强度弱化研究

海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。     

Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification

An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm.     

Interannual Sea Level Variations and Annual Tides in the Northwestern Pacific

Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone.     

Flow Cytometric Analysis of Coastal Lagoon Bacterioplankton and Picophytoplankton: Fixation and Storage Effects

The effect of different fixation and storage protocols on the flow cytometric (FCM) simultaneous analysis of bacterioplankton and phytoplankton in coastal seawater samples (Mediterranean coastal lagoons) was investigated. FCM measurements (cell number, fluorescence and scatter characteristics) were obtained through DAPI staining. Three fixatives [glutaraldehyde (GA), formaldehyde (FA) and paraformaldehyde (PFA)] and two storage (3 months duration) methods (5 °C and −196 °C) were tested. Two dominant populations were detected in studied samples: bacteria and eukaryotic picophytoplankton. Adding fixatives (2% final concentration) appears necessary to obtain FCM exhaustive counts of all the bacteria and phytoplanktonic cells. This was related to the permeation effect of fixatives which allowed a better DAPI staining of the cells. Maximum fluorescence, i.e. optimal staining of the cells was obtained with FA or PFA, and significant lower fluorescences with GA. Fixed samples stored at 5 °C induced rapid cell loss. Only storage in liquid nitrogen of samples fixed with FA or PFA, allows mid-term (≥4 months) preservation of bacteria or picophytoplankton cell numbers, and limited evolution of DAPI-induced fluorescence and scatter characteristics.     

INFORMATION FOR AUTHORS

<正>Acta Oceanologica Sinica(AOS)is a comprehensive academic journal edited by the Editorial Committee of Acta Oceanologica Sinica and is designed to provide a forum for important research papers of the marine scientific community which reflect the information on a worldwide basis.The journal publishes scholarly papers on marine science and technology,including physics,chemistry,biology,     

Deep-Sea Sediment Compression Curves: Some Controlling Factors, Spurious Overconsolidation, Predictions, and Geophysical Reproduction

Oedometer tests have been carried out on 70 undisturbed surficial clays (at approximately 250 mm below the mudline), mostly collected by free-fall corers from sites widely scattered throughout the deep-sea North Atlantic. Acoustic measurements were also made, initially on contiguous samples and ultimately on the same sample using a geophysically instrumented oedometer which also collected electrical resistivity data. Apart from those quiescent areas below the carbonate compensation depth, such as north of the West Indies where very fine clays exist, most of the samples are silty clays whose geotechnical-geophysical properties are dependent on the type of clay minerals present (and their ability to take in moisture), the sand-size fraction, and the quantity of carbonate present. Thus the pure clays have high compressibilities which decrease on the addition of coarse particles, while the converse is true for the acoustic parameters, these increasing with the sand fraction. Using the notion of the intrinsic compression line for all samples, and comparison to it of the measured compression curves, it is clear that, contrary to some previously held ideas, most deep-sea clays are normally consolidated; the addition of carbonate has the effect of creating an open, stronger sediment skeleton. Interestingly, where information is available, the variation with depth of a sample's acoustic velocity follows the void ratio pressure relationship of the compression curve. This allows the construction of an in-situ sediment compression curve using the in-situ geophysical observations.