Structural characteristics off Miyagi forearc region, the Japan Trench seismogenic zone, deduced from a wide-angle reflection and refraction study

The Japan Trench subduction zone, located east of NE Japan, has regional variation in seismicity. Many large earthquakes occurred in the northern part of Japan Trench, but few in the southern part. Off Miyagi region is in the middle of the Japan Trench, where the large earthquakes (M > 7) with thrust mechanisms have occurred at an interval of about 40 years in two parts: inner trench slope and near land. A seismic experiment using 36 ocean bottom seismographs (OBS) and a 12,000 cu. in. airgun array was conducted to determine a detailed, 2D velocity structure in the forearc region off Miyagi. The depth to the Moho is 21 km, at 115 km from the trench axis, and becomes progressively deeper landward. The P-wave velocity of the mantle wedge is 7.9–8.1 km/s, which is typical velocity for uppermost mantle without large serpentinization. The dip angle of oceanic crust is increased from 5–6° near the trench axis to 23° 150 km landward from the trench axis. The P-wave velocity of the oceanic uppermost mantle is as small as 7.7 km/s. This low-velocity oceanic mantle seems to be caused by not a lateral anisotropy but some subduction process. By comparison with the seismicity off Miyagi, the subduction zone can be divided into four parts: 1) Seaward of the trench axis, the seismicity is low and normal fault-type earthquakes occur associated with the destruction of oceanic lithosphere. 2) Beneath the deformed zone landward of the trench axis, the plate boundary is characterized as a stable sliding fault plain. In case of earthquakes, this zone may be tsunamigenic. 3) Below forearc crust where P-wave velocity is almost 6 km/s and larger: this zone is the seismogenic zone below inner trench slope, which is a plate boundary between the forearc and oceanic crusts. 4) Below mantle wedge: the rupture zones of thrust large earthquakes near land (e.g. 1978 off Miyagi earthquake) are located beneath the mantle wedge. The depth of the rupture zones is 30–50 km below sea level. From the comparison, the rupture zones of large earthquakes off Miyagi are limited in two parts: plate boundary between the forearc and oceanic crusts and below mantle wedge. This limitation is a rare case for subduction zone. Although the seismogenic process beneath the mantle wedge is not fully clarified, our observation suggests the two possibilities: earthquake generation at the plate boundary overridden by the mantle wedge without serpentinization or that in the subducting slab.     

Tomographic evidence for the subducting oceanic crust and forearc mantle serpentinization under Kyushu, Japan

We determined high-resolution three-dimensional P- and S-wave velocity (Vp, Vs) structures beneath Kyushu in Southwest Japan using 177,500 P and 174,025 S wave arrival times from 8515 local earthquakes. A Poisson's ratio structure was derived from the obtained Vp and Vs values. Our results show that significant low-Vp, low-Vs and high Poisson's ratio zones are extensively distributed along the volcanic front in the uppermost mantle, which extend and dip toward the back-arc side in the mantle wedge. In the crust, low-Vp, low-Vs and high Poisson's ratio anomalies exist beneath the active volcanoes. The subducting Philippine Sea slab is clearly imaged as a high-Vp, high-Vs and low Poisson's ratio zone from the Nankai Trough to the back-arc. A thin low-velocity zone is detected above the subducting Philippine Sea slab in the mantle wedge, and earthquakes in the upper mantle are distributed along the transition zone between this thin low-velocity zone and the high-velocity Philippine Sea slab, which may imply that oceanic crust exists on the top of the slab and the forearc mantle wedge is serpentinized due to the slab dehydration. The seismic velocity of the subducting oceanic crust with basaltic or gabbroic composition is lower than that of the mantle according to the previous studies. The serpentinization process could also dramatically reduce the seismic velocity in the forearc mantle wedge.     

Geology of the Yap Trench: new observations from a transect near 10°N from manned submersible Jiaolong

This paper describes the petrology and geochemistry of rocks from the Yap Trench acquired by three dives of the Jiaolong research submarine. Combining the geophysical data and submersible observations, this paper describes the geomorphology, shallow structures, and sedimentology of the Yap Trench and further discusses the tectonics and activities of this region. Two obvious slope breaks are found on the landward slope, and horsts and grabens with small fault offsets are observed in the ocean-ward slope of the trench. Peridotites sampled from the Yap Trench inner wall are highly depleted subduction-related mantle residues. Volcanic rocks in the northern segment of the trench have subduction-related characteristics that Yap fore-arc rocks underwent metasomatism during Cenozoic subduction. The rocks with remarkable lithologic difference from lithospheric mantle and upper crust sampled in the break slopes suggest that the slope break area may represent a lithologic boundary or transition zone. The landward slope of the Yap Trench was removed by subduction erosion as a result of collision with the Caroline Ridge. The bending of the down-going plate caused normal faults, horsts, and grabens with little or no sediments indicating that the Caroline Ridge is subducting beneath the Yap arc along the trench even though the convergence rate is very slow.     

High heat flow anomalies on an old oceanic plate observed seaward of the Japan Trench

Thirty-three new measurements on the seaward slope and outer rise of the Japan Trench along a parallel of 38°45′N revealed the existence of high heat flow anomalies on the subducting Pacific plate, where the seafloor age is about 135 m.y.. The most prominent anomaly with the highest value of 114 mW/m² is associated with a small mound on the outer rise, which was reported to be a kind of mud volcano. On the seaward slope of the trench, heat flow is variable: high (70–90 mW/m²) at some locations and normal for the seafloor age (about 50 mW/m²) at others. The spatial variation of heat flow may be related to development of normal faults and horst/graben structures due to bending of the Pacific plate before subduction, with fluid flow along the fault zones enhancing the vertical heat transfer. Possible heat sources of the high heat flow anomalies are intra-plate volcanism in the last several million years like that discovered recently on the Pacific plate east of the Japan Trench.     

Structural characteristics controlling the seismicity crustal structure of southern Japan Trench fore-arc region, revealed by ocean bottom seismographic data

The Japan Trench is a plate convergent zone where the Pacific Plate is subducting below the Japanese islands. Many earthquakes occur associated with plate convergence, and the hypocenter distribution is variable along the Japan Trench. In order to investigate the detailed structure in the southern Japan Trench and to understand the variation of seismicity around the Japan Trench, a wide-angle seismic survey was conducted in the southern Japan Trench fore-arc region in 1998. Ocean bottom seismometers (15) were deployed on two seismic lines: one parallel to the trench axis and one perpendicular. Velocity structures along two seismic lines were determined by velocity modeling of travel time ray-tracing method. Results from the experiment show that the island arc Moho is 18–20 km in depth and consists of four layers: Tertiary and Cretaceous sedimentary rocks, island arc upper and lower crust. The uppermost mantle of the island arc (mantle wedge) extends to 110 km landward of the trench axis. The P-wave velocity of the mantle wedge is laterally heterogeneous: 7.4 km/s at the tip of the mantle wedge and 7.9 km/s below the coastline. An interplate layer is constrained in the subducting oceanic crust. The thickness of the interplate layer is about 1 km for a velocity of 4 km/s. Interplate layer at the plate boundary may cause weak interplate coupling and low seismicity near the trench axis. Low P-wave velocity mantle wedge is also consistent with weak interplate coupling. Thick interplate layer and heterogeneous P-wave velocity of mantle wedge may be associated with the variation of seismic activity.     

Mid-Quaternary decoupling of sediment routing in the Nankai Forearc revealed by provenance analysis of turbiditic sands

Coring during Integrated Ocean Drilling Program Expeditions 315, 316, and 333 recovered turbiditic sands from the forearc Kumano Basin (Site C0002), a Quaternary slope basin (Site C0018), and uplifted trench wedge (Site C0006) along the Kumano Transect of the Nankai Trough accretionary wedge offshore of southwest Japan. The compositions of the submarine turbiditic sands here are investigated in terms of bulk and heavy mineral modal compositions to identify their provenance and dispersal mechanisms, as they may reflect changes in regional tectonics during the past ca. 1.5 Myrs. The results show a marked change in the detrital signature and heavy mineral composition in the forearc and slope basin facies around 1 Ma. This sudden change is interpreted to reflect a major change in the sand provenance, rather than heavy mineral dissolution and/or diagenetic effects, in response to changing tectonics and sedimentation patterns. In the trench-slope basin, the sands older than 1 Ma were probably eroded from the exposed Cretaceous–Tertiary accretionary complex of the Shimanto Belt and transported via the former course of the Tenryu submarine canyon system, which today enters the Nankai Trough northeast of the study area. In contrast, the high abundance of volcanic lithics and volcanic heavy mineral suites of the sands younger than 1 Ma points to a strong volcanic component of sediment derived from the Izu-Honshu collision zones and probably funnelled to this site through the Suruga Canyon. However, sands in the forearc basin show persistent presence of blue sodic amphiboles across the 1 Ma boundary, indicating continuous flux of sediments from the Kumano/Kinokawa River. This implies that the sands in the older turbidites were transported by transverse flow down the slope. The slope basin facies then switched to reflect longitudinal flow around 1 Ma, when the turbiditic sand tapped a volcanic provenance in the Izu-Honshu collision zone, while the sediments transported transversely became confined in the Kumano Basin. Therefore, the change in the depositional systems around 1 Ma is a manifestation of the decoupling of the sediment routing pattern from transverse to long-distance axial flow in response to forearc high uplift along the megasplay fault.     

Tectonic evolution of the triple junction off central Honshu for the past 1 million years

We discuss several models of the evolution of the trench-trench-trench triple junction off central Honshu during the past 1 m.y. on the basis of plate kinematics, morphology, gravity and seismic reflection profile data available for the area. The study area is characterized by large basins, 7–8 km deep on the inner lower trench slope on the Philippine Sea side and the deep (9 km) Izu-Bonin Trench to the east. Between the basins and the trench, there are 6–7 km-deep basement highs. The triple junction is unstable due to the movement of the Philippine Sea plate at a velocity of 3 cm/yr in WNW direction with respect to Eurasia (Northeast Japan), subparallel to the strike of the Sagami Trough. Generally we can expect the boundary area between the Philippine Sea and Pacific plates to be extended because the Pacific plate is unlikely to follow the retreating Philippine Sea plate due to the obstruction of the southeastern corner of Eurasia. The above peculiar morphology of the junction area could have resulted from this lack of stability. However, there are several possible ways to explain the above morphology.

Our gravity model across the trench-basement high-basin area shows that the basement highs are made of low-density materials (1.8–2 g/cm³). Thus we reject the mantle diapir model which proposes that the basement highs have been formed by diapiric injection of serpentinites between the retreating Philippine Sea plate and the Pacific plate.

The stretched basin model proposes that the basins have been formed by stretching of the Philippine Sea plate wedge. We estimated the extension to be about 10 km at the largest basin. We reconstructed the morphology at 1 Ma by moving the Philippine Sea plate 20 km farther to the east after closing the basins, and thus obtained 8 km depth of the 1 Ma trench, which is similar to that of the present Japan Trench to the north. Although this stretched basin model can explain the formation of the basins and the deep trench, other models are equally possible. For instance, the eduction model explains the origin of the basin by the eduction of the Philippine Sea basement from beneath the basement high, while the accretion model explains the basement highs by the accretion of the Izu-Bonin trench wedge sediments. In both of these models we can reconstruct the 1 Ma trench depth as about 8 km, similar to that of the stretched basin model.

The deformation of the basement of the basins constitutes the best criterion to differentiate between these models. The multi-channel seismic reflection profiles show that the basement of the largest basin is cut by normal faults, in particular at its eastern edge. This suggests that the stretched basin model is most likely. However, the upper part of the sediments shows that the basement high to the east has been recently uplifted. This uplift is probably due to the recent (0.5 Ma) start of accretion of the trench wedge sediments beneath this basement high.     

Flexural response of the oceanic lithosphere at an arc—arc junction: implication for the subduction of aseismic ridges

The deformation of the oceanic lithosphere subducting at the junction of two trenches is studied by means of a three-dimensional finite-element analysis. Results show that the existence of a junction (i.e. a change in trend of the trench axis) yields a specific shape of the outer topographic rise. In a convex junction area—such as the Japan and Kuril trenches, the topographic bulge presents a “dome”, whereas in a concave junction area—such as the Java and Sumatra trenches, this bulge is less pronounced. These theoretical results are confirmed by the bathymetry seaward of the junctions of the Japan and Kuril trenches and of the Peru-Chile trench. Moreover, the existence of the abnormal topographic dome in front of a convex junction contributes to the creation of normal faults which help the subduction of seamounts or of other bathymetric features in such areas.     

Ocean trench blocked and obliterated by Banda forearc collision with Australian proximal continental slope

The bathymetry and abrupt changes in earthquake seismicity around the eastern end of the Java Trench suggest it is now blocked south–east of Sumba by the Australian, Jurassic-rifted, continental margin forming the largely submarine Roti–Savu Ridge. Plate reconstructions have demonstrated that from at least 45 Ma the Java Trench continued far to the east of Sumba. From about 12 Ma the eastern part of the Java Trench (called Banda Trench) continued as the active plate boundary, located between what was to become Timor Island, then part of the Australian proximal continental slope, and the Banda Volcanic Arc. This Banda Trench began to be obliterated by continental margin-arc collision between about 3.5 and 2 Ma.The present position of the defunct Banda Trench can be located by use of plate reconstructions, earthquake seismology, deep reflection seismology, DSDP 262 results and geological mapping as being buried under the para-autochthon below the foothills of southern Timor. Locating the former trench guides the location of the apparently missing large southern part of the Banda forearc that was carried over the Australian continental margin during the final stage of the period of subduction of that continental margin that lasted from about 12 Ma to about 3.5 Ma.Tectonic collision is defined and distinguished from subduction and rollback. Collision in the southern part of the Banda Arc was initiated when the overriding forearc basement of the upper plate reached the proximal part of the Australian continental slope of the lower plate, and subduction stopped. Collision is characterised by fold and thrust deformation associated with the development of structurally high decollements. This collision deformed the basement and cover of the forearc accretionary prism of the upper plate with part of the unsubducted Australian cover rock sequences from the lower plate. Together with parts of the forearc basement they now form the exposed Banda orogen. The conversion of the northern flank of the Timor Trough from being the distal part of the Banda forearc accretionary prism, carried over the Australian continental margin, into a foreland basin was initiated by the cessation of subduction and simultaneous onset of collisional tectonics.This reinterpretation of the locked eastern end of the Java Trench proposes that, from its termination south of Sumba to at least as far east as Timor, and probably far beyond, the Java-Banda Trench and forearc overrode the subducting Australian proximal continental slope, locally to within 60 km of the shelf break. Part of the proximal forearc's accretionary prism together with part of the proximal continental slope cover sequence were detached and thrust northwards over the Java-Banda Trench and forearc by up to 80 km along the southwards dipping Savu Thrust and Wetar Suture. These reinterpretations explain the present absence of any discernible subduction ocean trench in the southern Banda Arc and the narrowness of the forearc, reduced to 30 km at Atauro, north of East Timor.     

Zenisu Ridge: mechanical model of formation

Seabeam, seismic and submersible surveys took place during the Kaiko Project and revealed significant compressive deformation at the northeastern end of the Philippine Sea plate, related to the recent collision of the Izu-Ogasawara Arc against Central Japan. Intraoceanic thrusting at the base of the Zenisu Ridge, a linear topographic high running a few tens of kilometers south of the Nankai Trough, is supported by tectonic, magnetic and gravimetric data. We investigate the formation of the Zenisu Ridge in terms of compressive mechanical failure of a thin elastic-perfectly plastic plate, subducting at a trench and subject to a regional compressive axial force. The rheological envelope concept is used throughout the numerical calculations. Based on a detailed study of flexure of the present-day bending far from the deformation zone, we evaluate the bending forces involved: the bulge is 120 to 150 m high and the compressive stress all along the Nankai Trough is about −100 MPa. In the Zenisu Ridge area, an additional compressive stress is superimposed due to the nearby collision at Izu-Peninsula. We compute the vertical distribution of the deviatoric stress before failure and find that the deviatoric stress is maximum at a depth of 20–25 km in the trench area, and again at the surface 60 to 100 km seaward, in the vicinity of the bulge. The development of a thrust joining these two maxima through the entire thickness of the lithosphere is discussed. The model predicts that the formation of the Zenisu Ridge did not occur before 4 Ma and is caused by progressive tectonic uplift due to the redistribution of bending stresses as the ridge approaches the Nankai Trough.     

Deep slab subduction and dehydration and their geodynamic consequences: Evidence from seismology and mineral physics

We present new pieces of evidence from seismology and mineral physics for the existence of low-velocity zones in the deep part of the upper mantle wedge and the mantle transition zone that are caused by fluids from the deep subduction and deep dehydration of the Pacific and Philippine Sea slabs under western Pacific and East Asia. The Pacific slab is subducting beneath the Japan Islands and Japan Sea with intermediate-depth and deep earthquakes down to 600 km depth under the East Asia margin, and the slab becomes stagnant in the mantle transition zone under East China. The western edge of the stagnant Pacific slab is roughly coincident with the NE–SW Daxing'Anling-Taihangshan gravity lineament located west of Beijing, approximately 2000 km away from the Japan Trench. The upper mantle above the stagnant slab under East Asia forms a big mantle wedge (BMW). Corner flow in the BMW and deep slab dehydration may have caused asthenospheric upwelling, lithospheric thinning, continental rift systems, and intraplate volcanism in Northeast Asia. The Philippine Sea slab has subducted down to the mantle transition zone depth under Western Japan and Ryukyu back-arc, though the seismicity within the slab occurs only down to 200–300 km depths. Combining with the corner flow in the mantle wedge, deep dehydration of the subducting Pacific slab has affected the morphology of the subducting Philippine Sea slab and its seismicity under Southwest Japan. Slow anomalies are also found in the mantle under the subducting Pacific slab, which may represent small mantle plumes, or hot upwelling associated with the deep slab subduction. Slab dehydration may also take place after a continental plate subducts into the mantle.     

Deep slab subduction and dehydration and their geodynamic consequences: Evidence from seismology and mineral physics

We present new pieces of evidence from seismology and mineral physics for the existence of low-velocity zones in the deep part of the upper mantle wedge and the mantle transition zone that are caused by fluids from the deep subduction and deep dehydration of the Pacific and Philippine Sea slabs under western Pacific and East Asia. The Pacific slab is subducting beneath the Japan Islands and Japan Sea with intermediate-depth and deep earthquakes down to 600 km depth under the East Asia margin, and the slab becomes stagnant in the mantle transition zone under East China. The western edge of the stagnant Pacific slab is roughly coincident with the NE–SW Daxing'Anling-Taihangshan gravity lineament located west of Beijing, approximately 2000 km away from the Japan Trench. The upper mantle above the stagnant slab under East Asia forms a big mantle wedge (BMW). Corner flow in the BMW and deep slab dehydration may have caused asthenospheric upwelling, lithospheric thinning, continental rift systems, and intraplate volcanism in Northeast Asia. The Philippine Sea slab has subducted down to the mantle transition zone depth under Western Japan and Ryukyu back-arc, though the seismicity within the slab occurs only down to 200–300 km depths. Combining with the corner flow in the mantle wedge, deep dehydration of the subducting Pacific slab has affected the morphology of the subducting Philippine Sea slab and its seismicity under Southwest Japan. Slow anomalies are also found in the mantle under the subducting Pacific slab, which may represent small mantle plumes, or hot upwelling associated with the deep slab subduction. Slab dehydration may also take place after a continental plate subducts into the mantle.     

西南日本火山区三维地震成像研究

利用日本气象厅(JMA)以及日本国立大学联合地震观测台网(JUNEC)记录到的3218个地震事件的231918条P波到时资料,反演求得西南日本160km深度范围内的三维P波速度结构。研究表明,在九州地区,俯冲的菲律宾海板块以高速为主要特征,该海洋板块在30～60km深度处的脱水使得弧前地幔楔顶端的橄榄石蛇纹岩化,在120km深度处的脱水使得地幔楔中的岩石局部熔融,融体上升引起该区的火山活动。在本州西部地区大山火山之下,低速异常显著,并伴随低频地震活动,说明该火山可能是个潜在的活火山,将来有喷发的可能性。     

Imaging of Vp, Vs, and Poisson’s ratio anomalies beneath Kyushu, southwest Japan: Implications for volcanism and forearc mantle wedge serpentinization

We determine detailed 3-D V_p and V_s structures of the crust and uppermost mantle beneath the Kyushu Island, southwest Japan, using a large number of arrival times from local earthquakes. From the obtained V_p and V_s models, we further calculate Poisson’s ratio images beneath the study area. By using this large data set, we successfully image the 3-D seismic velocity and Poisson’s ratio structures beneath Kyushu down to a depth of 150 km with a more reliable spatial resolution than previous studies. Our results show very clear low V_p and low V_s anomalies in the crust and uppermost mantle beneath the northern volcanoes, such as Abu, Kujyu and Unzen. Low-velocity anomalies are seen in the mantle beneath most other volcanoes. In contrast, there are no significant low-velocity anomalies in the crust or in the upper mantle between Aso and Kirishima. The subducting Philippine Sea slab is imaged generally as a high-velocity anomaly down to a depth of 150 km with some patches of normal to low seismic wave velocities. The Poisson’s ratio is almost normal beneath most volcanoes. The crustal seismicity is distributed in both the high- and low-velocity zones, but most distinctly in the low Poisson’s ratio zone. A high Poisson’s ratio region is found in the forearc crustal wedge above the slab in the junction area with Shikoku and Honshu; this high Poisson’s ratio could be caused by fluid-filled cracks induced by dehydration from the Philippine Sea slab. The Poisson’s ratio is normal to low in the forearc mantle in middle-south Kyushu. This is consistent with the absence of low-frequency tremors, and may indicate that dehydration from the subducting crust is not vigorous in this region.     

Unstable forearc stress in the eastern Nankai subduction zone for the last 2 million years

Transpressional tectonics characterizes the SW Japan arc. However, we will show in this article that offshore seismic profiles and onshore mesoscale faults indicate that the eastern part of the forearc was subject to transtensional tectonics since ca. 2.0 Ma. Offshore normal faults imaged on the profiles run parallel to the Nankai Trough, and started activity at 1.0 Ma, but transtensional tectonics commenced the onshore area earlier. In order to understand the stress history in the forearc region, we collected fault-slip data from onshore mesoscale faults in Plio-Pleistocene sedimentary rocks in the Kakegawa area at the northeastern extension of the offshore normal faults. Most of the mesoscale faults are oblique-normal, indicating that the area was subject to transtensional tectonics. The faults suggest that the compressional tectonic regime was followed by the transtensional one at 2.0 Ma, in agreement with regional tectonostratigraphic data, which indicate that folding ceased at that time. Present compressional stress followed the transtensional tectonic regime sometime in the late Pleistocene. Transtensional or extensional tectonic zone shifted from the Kakegawa area to the offshore region.These observations indicate that the state of stress just behind the accretionary prism of the eastern Nankai subduction zone has been unstable in the last 2 million years, suggesting that the forearc wedge has been at critical state in that gravitational force and basal shear traction on the wedge have been balanced, but the forearc tectonics has been susceptible to small perturbations. Possible factors compatible with the observed stress history include the change of subduction direction of the plate at 1.0 Ma, and the rapid uplift of Central Japan thereafter.     

Geochemistry of subducted metabasites exhumed from the Mariana forearc: Implications for Pacific seamount subduction

Seamounts on the drifting oceanic crust are inevitably carried by plate motions and eventually accreted or subducted. However, the geochemical signatures of the subducted seamounts and the significance of seamount subduction are not well constrained. Hundreds of seamounts have subducted beneath the Philippine Sea Plate following the westward subduction of the Pacific Plate since the Eocene (~52 Ma). The subducted oceanic crust and seamount materials can be exhumed from the mantle depth to the seafloor in the Mariana forearc region by serpentinite mud volcanoes, providing exceptional opportunities to directly study the subducted oceanic crust and seamounts. The International Ocean Discovery Program (IODP) expedition 366 has recovered a few metamorphosed mafic clasts exhumed from the Mariana forearc serpentinite mud volcanoes, e.g., the Fantangisña and Asùt Tesoru seamounts. These mafic clasts have tholeiitic to alkaline affinities with distinct trace elements and Nd-Hf isotopes characteristics, suggesting different provenances and mantle sources. The tholeiites from the Fantangisña Seamount have trace element characteristics typical of mid-ocean ridge basalt. The Pacific-type Hf-Nd isotopic compositions, combined with the greenschist metamorphism of these tholeiites further suggest that they came from the subducted Pacific oceanic crust. The alkali basalts-dolerites from the Fantangisña and Asùt Tesoru seamounts show ocean island basalt (OIB)-like geochemical characteristics. The OIB-like geochemical signatures and the low-grade metamorphism of these alkali basalts-dolerites suggest they came from subducted seamounts that originally formed in an intraplate setting on the Pacific Plate. The Pacific Plate origin of these metabasites suggests they were formed in the Early Cretaceous or earlier.Two types of OIBs have been recognized from alkali metabasites, one of which is geochemically similar to the HIMU-EMI-type OIBs from the West Pacific Seamount Province, and another is similar to the EMII-type OIBs from the Samoa Island in southern Pacific, with negative Nb-Ta-Ti anomalies and enriched Nd-Hf isotopes. Generally, these alkali metabasites are sourced from the heterogeneous mantle sources that are similar to the present South Pacific Isotopic and Thermal Anomaly. This study provides direct evidence for seamount subduction in the Mariana convergent margins. We suggest seamount subduction is significant to element cycling, mantle heterogeneity, and mantle oxidation in subduction zones.     

On the role of subducting oceanic plateaus in the development of shallow flat subduction

Oceanic plateaus, aseismic ridges or seamount chains all have a thickened crust and their subduction has been proposed as a possible mechanism to explain the occurrence of flat subduction and related absence of arc magmatism below Peru, Central Chile and at the Nankai Trough (Japan). Their extra compositional buoyancy could prohibit the slab from sinking into the mantle. With a numerical thermochemical convection model, we simulated the subduction of an oceanic lithosphere that contains an oceanic crustal plateau of 18-km thickness. With a systematic variation, we examined the required physical parameters to obtain shallow flat subduction. Metastability of the basaltic crust in the eclogite stability field is of crucial importance for the slab to remain buoyant throughout the subduction process. In a 44-Ma-old subducting plate, basalt must be able to survive a temperature of 600–700 °C to keep the plate buoyant sufficiently long to cause a flat-slab segment. We found that the maximum yield stress in the slab must be limited to about 600 MPa to allow for the necessary bending to the horizontal. Young slabs show flat subduction for larger parameter ranges than old slabs, since they are less gravitationally unstable and show less resistance against bending. Hydrous weakening of the mantle wedge area and lowermost continent are required to allow for the necessary deformation of a change in subduction style from steep to flat. The maximum flat slab extent is about 300 km, which is sufficient to explain the observed shallow flat subduction near the Nankai Trough (Japan). However, additional mechanisms, such as active overthrusting by an overriding continental plate, need to be invoked to explain the flat-slab segments up to 500 km long below Peru and Central Chile.     

Three-dimensional P- and S-wave velocity structures beneath the Japan Islands obtained by high-density seismic stations by seismic tomography

We construct fine-scale 3D P- and S-wave velocity structures of the crust and upper mantle beneath the whole Japan Islands with a unified resolution, where the Pacific (PAC) and Philippine Sea (PHS) plates subduct beneath the Eurasian (EUR) plate. We can detect the low-velocity (low-V) oceanic crust of the PAC and PHS plates at their uppermost part beneath almost all the Japan Islands. The depth limit of the imaged oceanic crust varies with the regions. High-V_P/V_S zones are widely distributed in the lower crust especially beneath the volcanic front, and the high strain rate zones are located at the edge of the extremely high-V_P/V_S zone; however, V_P/V_S at the top of the mantle wedge is not so high. Beneath northern Japan, we can image the high-V subducting PAC plate using the tomographic method without any assumption of velocity discontinuities. We also imaged the heterogeneous structure in the PAC plate, such as the low-V zone considered as the old seamount or the highly seismic zone within the double seismic zone where the seismic fault ruptured by the earthquake connects the upper and lower layer of the double seismic zone. Beneath central Japan, thrust-type small repeating earthquakes occur at the boundary between the EUR and PHS plates and are located at the upper part of the low-V layer that is considered to be the oceanic crust of the PHS plate. In addition to the low-V oceanic crust, the subducting high-V PAC plate is clearly imaged to depths of approximately 250 km and the subducting high-V PHS zone to depths of approximately 180 km is considered to be the PHS plate. Beneath southwestern Japan, the iso-depth lines of the Moho discontinuity in the PHS plate derived by the receiver function method divide the upper low-V layer and lower high-V layer of our model at depths of 30–50 km. Beneath Kyushu, the steeply subducting PHS plate is clearly imaged to depths of approximately 250 km with high velocities. The high-V_P/V_S zone is considered as the lower crust of the EUR plate or the oceanic crust of the PHS plate at depths of 25–35 km and the partially serpentinized mantle wedge of the EUR plate at depths of 30–45 km beneath southwestern Japan. The deep low-frequency nonvolcanic tremors occur at all parts of the high-V_P/V_S zone—within the zone, the seaward side, and the landward side where the PHS plate encounters the mantle wedge of the EUR plate. We prove that we can objectively obtain the fine-scale 3D structure with simple constraints such as only 1D initial velocity model with no velocity discontinuity.     

Seamount subduction and rupture characteristics of the March 11, 2011, Tohoku earthquake

We suggest that the spatial location of the 2011 Tohoku earthquake rupture and slip distribution on it was strongly influenced by the subduction of seamount chains. Subduction of seamounts across the Japan trench caused weak coupling on the plate interface which acted as barriers to the 2011 Tohoku earthquake rupture and thus delimited it.     

Birth of a major strike-slip fault in SW Japan

A 500 km-long strike-slip fault, the North Chugoku Shear Zone (NCSZ) is identified in SW Japan, responsible for four M > 7 earthquakes in the past 130 years. A new geodynamic mechanism of increased interplate coupling above an obliquely subducting flat slab is presented to explain the transfer of trench parallel motion 400 km inland from the Nankai Trough, to the level of the Quaternary adakitic volcanic arc. While Quaternary dextral strike-slip motion is widely believed to have occurred along the Median Tectonic Line (MTL), near the Miocene volcanic arc, the central segment in Shikoku has shown little seismicity for the last 1000 years. Pure dextral strike-slip focal mechanisms for 15 modern and historical events indicate that part of the transcurrent motion is being transferred from the MTL to the NCSZ.