施工缝对框架结构抗震性能影响的数值分析

为研究施工缝对框架结构抗震性能的影响,利用提出的施工缝模型,基于OPENSEES平台建模进行静力非线性分析和非线性动力时程分析。通过对比整浇框架与带缝框架的顶点最大位移、层间位移角、塑性铰出现和分布规律等明确施工缝对框架结构的抗震性能的影响程度。结果表明,施工缝使框架结构的变形和层间位移角显著增大,并且使8、9度区框架结构的层间位移角分布发生改变;施工缝使柱端更易出现塑性铰,更易发生"强梁弱柱"的破坏模式;在高烈度区,施工缝的影响比较显著,如果忽略其影响,将会高估框架结构的抗震性能。     

不同延性条件下框架柱塑性铰区箍筋抗剪能力试验研究

允许钢筋混凝土框架柱端出现塑性铰但又不形成柱铰破坏机构是一个十分现实而又未得以很好解决的课题。通过10个钢筋混凝土框架柱构件抗震剪切抗力的试验研究,明确了加载全过程骶架柱构件中箍筋与混凝土的抗剪贡献及比例,分析了框架柱塑性铰区抗剪机理,为框架柱基于延性的抗震设计提供了试验依据。     

地震区混凝土框架柱塑性铰区剪切抗力延性设计试验研究

允许钢筋混凝土框架柱端出现塑性铰但又不形成柱铰破坏机构是一个十分现实而又未得以很好解决的课题。通过10个钢筋混凝土框架柱构件抗震剪切抗力的试验研究,明确了加载全过程框架柱构件中箍筋与混凝土的抗剪贡献及比例,并根据相关试验资料,提出了反复荷载下框架柱抗剪承载力随构件延性系数的变化关系,并提出了框架柱塑性铰区抗震剪切承载力延性计算公式,部分成果已为修订《混凝土结构设计规范》采用。     

反复荷载下混凝土框架柱塑性铰区基于延性的抗剪承载力机理分析

在试验研究的基础上,以框架结构延性设计为目的采用桁架＋拱模型研究了框架柱塑性铰区域抗剪受力机理,分析了,位移延性系数、加载循环次数等因素对框架柱构件塑性铰区域剪切受力性能的影响,并结合试验结果提出了混凝土框架柱塑性铰区域剪切承载力抗震延性设计实用公式,可有效实现结构的延性破坏机制。主要为配合GBJ10-89的修订,该成果已被《混凝土结构设计规范》（GB50010—2003）吸收。     

钢筋混凝土框架结构层间位移角与构件变形关系研究

层间位移角已作为检验建筑结构抗震性能的主要指标之一而被广泛应用。为实现该指标在钢筋混凝土框架结构基于位移的抗震设计中的应用,研究了层间位移角与构件变形之间的关系。首先,采用对部分子结构的弹性理论分析得到了弹性阶段梁变形对层间位移角贡献比例的计算公式。接着,采用对15层钢筋混凝土框架整体结构的非线性地震反应计算结果的统计分析得到了在塑性阶段梁变形对层间位移角的贡献比例回归计算公式。所建立的计算公式反映了梁与柱的相对刚度和强度比例、层闽塑性变形程度的影响。最后,应用该方法进行了一算例分析,计算结果和试验结果比较一致。利用本文提出的计算方法可以方便地把对框架结构的层间位移需求转变为对梁、柱构件的变形要求。     

混凝土框架柱塑性铰区域剪切破坏形态的试验研究

允许钢筋混凝土框架柱端出现塑性铰但又不形成柱铰破坏机构是一个十分现实而又未得以很好解决的课题。通过10个钢筋混凝土框架柱构件抗震剪切抗力的试验研究，详细研究了塑性铰区的主要破坏形态、主要破坏特征及其发生条件，讨论了构件塑性铰区主要破坏形态的分类标准，为混凝土框架柱的抗震延性设计提供了试验依据。     

混凝土框架柱塑性铰区抗剪性能非线性有限元分析

为保证框架柱端塑性铰达到预期的塑性转动之前,柱端塑性铰区不出现剪切破坏,结合框架柱塑性铰区抗剪承载力的试验研究,利用ANSYS对10个框架柱构件塑性铰区的抗剪性能进行了非线性有限元分析;有限元模型中混凝土采用SOLID65单元,钢筋采用LINK8单元,分离式建模,施加约束时将试验构件上梁上端表面的所有节点在竖直方向耦合,以保证塑性铰出现在柱端;计算了10个构件的骨架曲线,框架柱塑性铰区弹性工作阶段、带裂缝工作阶段和破坏阶段的应力云图和破坏时的裂缝分布图,将以上计算结果与试验结果进行了对比,数值计算结果和试验结果符合良好,验证了有限元模型建立的准确性,所建模型可为今后同类问题的非线性有限元计算提供参考。     

型钢混凝土框架pushover分析

Pushover分析方法是逐渐得到广泛应用的一种评估结构抗震性能的简化方法。由于型钢混凝土（SRC）构件塑性铰属性确定方面的原因,SRC构件难以直接应用于pushover分析方法,而常采用按“等刚度”原则转化为钢筋混凝土构件（RC）进行计算。本文从理论上给出了SRC压弯构件N-M相关曲线、Mx-My相关曲线的形成方法,提出了SRC构件M-φ曲线的确定及转化为塑性铰曲线的原则,并研究了SRC构件塑性铰区等效长度的计算方法,可为SRC结构进行pushover分析提供参考数据。按照本文方法,采用pushover方法对两跨三层SRC框架进行分析,结果与该结构模型振动台实验吻合较好。在此基础上,对10层SRC框架和采用刚度等效的3层、10层的钢筋混凝土（RC）框架进行了对比分析,结果表明,随着层数的增加,SRC结构相对于RC结构表现出更优越的抗震耗能能力。     

高阶振型对建筑结构层间位移的影响1

建筑结构层间位移是抗震设计的研究重点。本文基于广义层间位移谱,分析高阶振型对结构最大层间位移角以及对结构层间位移沿无量纲高度分布的影响,并通过调整结构侧向刚度比,分析高阶振型对结构层间位移变形类型的影响。结果表明:随着结构固有周期的增加,仅取一阶振型进行分析将会显著低估结构的最大层间位移角,高阶振型的影响决不能忽视;从结构层间位移沿无量纲高度分布的角度分析,高阶振型将会显著增加结构中上部位的层间位移需要;高阶振型将增加长周期结构的剪切变形和中上部位的弯曲变形需求,但对中下部位弯曲变形的影响并不明显;针对长周期结构的设计和分析,除计算最大层间位移角外,建议考虑层间位移沿结构高度的分布情况。     

新型截面SRC梁柱节点抗剪承载力计算研究

提出新型截面(正向和斜向布置扩大十字型钢)型钢混凝土(SRC)柱-I字型钢SRC梁节点的构造措施。通过4个新型截面SRC柱-I字型钢SRC梁节点试件与1个普通SRC梁柱节点试件的低周反复荷载试验,研究试件的破坏特征和节点区剪力-剪切角关系,分析配钢形式、加载角度和构造措施对节点剪切变形的影响,并进一步提出实腹式SRC梁柱节点的受剪机理,结果表明,新型截面SRC梁柱节点发生核心区剪切破坏,其受力机理为斜压杆、刚框架-钢板剪力墙和约束机理的综合作用。通过对数值模拟数据的回归分析,采用叠加方法,提出考虑型钢腹板、箍筋和轴压比的新型截面SRC梁柱节点抗剪承载力计算公式,计算值与试验结果吻合较好。     

Cyclic response of slender RC columns typical of precast industrial buildings

The cyclic behaviour of slender cantilever columns in full-scale models of precast industrial buildings, designed by Eurocode 8, was studied experimentally and analytically. The shear span ratio of the columns was 12.5, which is more than allowed by Eurocode 8 for columns in frame structures (10). High deformability and a large deformation capacity (8%~drift) of the columns was observed. A lumped plasticity model was used in the analysis. In the paper the observed behaviour of the models has been compared with the predicted behaviour obtained by several empirically based models and procedures. It was observed that these models, which were developed for much lower shear span ratios (2–6), were not applicable for the analyzed very slender columns without appropriate additional considerations and modifications. In the case of such columns the yield drift is dominated by the flexural mode (it is practically proportional to the height of the column) and the ultimate drift under cyclic loading conditions is only slightly dependent on the shear span (indicating that the ratio of the equivalent length of the plastic hinge to the height of the column decreases with the increasing shear span). An appropriately modified lumped plasticity model incorporating in-cycle and repeated-cycle strength deterioration was chosen for future use in performance-based design and seismic risk studies.     

Cyclic performance of large‐scale corroded reinforced concrete beams

Nine large‐scale beam specimens were constructed. Of which, one was used as the control, whereas the other eight ones were divided into four sets. Each set had two specimens and was subjected to accelerated corrosion using an imposed current for the same time interval. Following the corrosion, a specimen in each set was tested using cyclic loading to examine the seismic performance, whereas the other one was demolished to examine the extent of corrosion. Cyclic loading results indicated that with an increasing corrosion level, the ultimate drift, ductility, plastic rotation capacity, and energy dissipation of the beams initially increased and later decreased. The failure mode switched from flexural failure, largely owing to buckling of the longitudinal reinforcement to flexural‐shear failure, which is mainly caused by fracturing of the transverse reinforcement. Corrosion increased shear deformation and the spread of plasticity of the plastic hinge region. The residual flexural strength, as estimated by an empirical equation based on the maximum pit depth in the longitudinal reinforcement, closely corresponds to experimental values. Furthermore, the residual shear strength estimated based on the minimum reduced cross‐sectional area of transverse reinforcement correlates better with the experimental observations than that based on the weight loss. Copyright © 2011 John Wiley & Sons, Ltd.     

The seismic shear of ductile cantilever wall systems in multistorey structures

The distribution of seismic base shear demand among ductile flexural cantilever walls, comprising the lateral load resisting system of a multistorey building, is studied. It is shown that the base shear force demand depends on the sequence of hinge formation at the wall bases, and this in turn depends on the relative wall lengths. Hence, the routine elastic approach in which the shear forces are allocated per relative flexural rigidity or (when some consideration is given to plastic hinge formation) to moment capacity at the wall base, may appreciably underestimate the shear force demand on the walls, particularly the shorter (usually the more flexible) ones. A simple procedure yielding the results of ‘cyclic’ pushover analysis is proposed to predict the peak seismic wall forces for a given total base shear when plastification is confined to the wall base. The effects of plastic hinges developing at higher floors on (1) shear distribution among the walls and (2) the in‐plane floor forces are also considered. Two numerical examples are presented to demonstrate the main points made. Copyright © 2004 John Wiley & Sons, Ltd.     

Experimental study of hollow rectangular bridge column performance under vertical and cyclically bilateral loads

To investigate the seismic performance of hollow reinforced concrete(RC) bridge columns of rectangular cross section under constant axial load and cyclically biaxial bending,five specimens were tested.A parametric study is carried out for different axial load ratios,longitudinal reinforcement ratios and lateral reinforcement ratios.The experimental results showed that all tested specimens failed in the flexural failure mode and their ultimate performance was dominated by flexural capacity,which is represented by the rupture/buckling of tensile longitudinal rebars at the bottom of the bridge columns.Biaxial force and displacement hysteresis loops showed significant stiffness and strength degradations,and the pinching effect and coupling interaction effect of both directions severely decrease the structural seismic resistance.However,the measured ductility coefficient varying from 3.5 to 5.7 and the equivalent viscous damping ratio varying from 0.19 and 0.26 can meet the requirements of the seismic design.The hollow RC rectangular bridge columns with configurations of lateral reinforcement in this study have excellent performance under bidirectional earthquake excitations,and may be considered as a substitute for current hollow RC rectangular section configurations described in the Guideline for Seismic Design of Highway Bridges(JTG/T B02-01-2008).The length of the plastic hinge region was found to approach one sixth of the hollow RC rectangular bridge column height for all specimen columns,and it was much less than those specified in the current JTG/T.Thus,the length of the plastic hinge region is more concentrated for RC rectangular hollow bridge columns.     

A shear design equation for ductile R/C members

A design equation is proposed to prevent shear failure after flexural inelastic deformation. This equation is based on the truss-strut model. Inelastic hinge rotation is assumed to reduce the effective strength of concrete and to increase the inclination of truss action inside hinge regions. The proposed equation is confirmed on the basis of existing experimental data. This equation is accepted in the 1990 Japanese Design Guidelines.     

Stiffness and cyclic deformation capacity of circular RC columns with or without lap-splices and FRP wrapping

Mechanics-based models are developed for the moment, the curvature and the chord rotation at yielding of circular concrete columns or piers, their secant stiffness to the yield point and the ultimate curvature and flexure-controlled ultimate chord rotation in cyclic loading. The strain criteria for yielding or ultimate are calibrated on the basis of over four hundred test results. Besides the model for the secant-to-yield-point stiffness which is in terms of the yield moment and chord rotation, an empirical one, independent of the vertical reinforcement, is fitted to the data. The ultimate chord rotation is obtained from a plastic hinge model employing a plastic hinge length, the yield and the ultimate curvatures of the end section and the fixed-end rotation due to slippage of bars from their anchorage zone beyond the column length. All models are extended to columns the vertical bars of which are lap-spliced within the plastic hinge and to columns with FRP wrapping and continuous or lap-spliced vertical bars. The comprehensive portfolio of expressions proposed for the deformation properties of circular columns is fully consistent across the various situations of continuous or lap-spliced bars, with or without FRP wrapping, and with models developed by the authors from much larger databases of rectangular columns in similar situations; the aspects specific to circular sections are limited to the mechanics-based section analysis for moment and curvature, a purely empirical coefficient for the secant-to-yield-point stiffness and the empirical plastic hinge length.     

CFRP板条嵌入式加固RC框架节点的抗震性能试验研究及有限元分析

为验证 CFRP板条嵌入式加固方法对提升十字形 RC框架节点抗震性能的有效性,开展了1 个 CFRP板条嵌入式加固节点和1个对比节点的拟静力试验研究.试验结果表明:在核心区及相邻梁端嵌入 CFRP板条可起到类似箍筋的抗剪作用,使得节点由核心区剪切破坏转变为梁端受弯破坏,且梁铰得到转移;构件抗震性能明显提升,承载力和延性分别提高了16．3%和13．7%.同时, 利用 ABAQUS建立试验数据验证的有限元模型,并对节点主要加固设计参数进行影响分析.结果表明,节点承载力随着 CFRP板条面积的增大、板条间距的减小和基体混凝土强度的提高而提高.所提节点加固方法体现出塑性铰转移的抗震设计理念,同时提高核心区抗剪强度和梁端的抗弯强度,可用于 RC节点的抗震加固.     

Estimation of monotonic behavior of reinforced concrete columns considering shear‐flexure‐axial load interaction

Reinforced concrete columns with insufficient transverse reinforcement and non‐seismic reinforcement details are vulnerable to brittle shear failure and to loss of axial load carrying capacity in the event of a strong earthquake. In this paper, a procedure is presented after examining the application of two macro models for displacement‐based analysis of reinforced concrete columns subjected to lateral loads. In the proposed model, lateral load‐deformation response of the column is simulated by estimating flexural and shear deformation components separately while considering their interaction and then combining these together according to a set of rules depending upon column's yield, flexural and shear strengths. In addition, lateral deformation caused by reinforcement slip in beam–column joint regions and buckling of compression bars are taken into account and considered in the analysis. Implementation of the proposed procedure produces satisfactory lateral load–displacement relationships, which are comparable with experimental data. Copyright © 2012 John Wiley & Sons, Ltd.     

强震下四边钢柱支承单层柱面网壳弹塑性地震响应研究

采用集中塑性铰理论和SAP2000结构分析软件,对某体育练习馆（钢柱周边支承单层柱面网壳）整体结构进行了强震下弹塑性地震响应分析。分析中考虑了几何和材料双重非线性影响,获得了节点位移响应、杆件塑性铰的分布特征和结构的整体变形与失效形态,并评定了整体结构在强震下的极限承载力与失效类型。结果表明：该结构在强震下的失效界限地震加速度峰值为1260gal,最大竖向变形为短向跨度的1/163,满足＂避难与救灾建筑结构＂的抗震性能设防要求;结构的失效类型为动力失稳破坏,临界失效时出现塑性铰的杆件较少,结构塑性发展程度不充分;由整体稳定控制的单层柱面网壳在满足稳定承载力的要求下具有较大的抗震潜能。