Lessons learned from the ＂5.12＂ Wenchuan Earthquake： evaluation of earthquake performance objectives and the importance of seismic conceptual design principles

Many different types of buildings were severely damaged or collapsed during the May 12, 2008 Great Wenchuan Earthquake. Based on survey data collected in regions that were subjected to moderate to severe earthquake intensities, a comparison between the observed building damage, and the three earthquake performance objectives and seismic conceptual design principles specified by the national ＂Code for Seismic Design of Buildings GB50011-2001,＂ was carried out. Actual damage and predicted damage for a given earthquake level for different types of structures is compared. Discussions on seismic conceptual design principles, with respect to multiple defense lines, strong column-weak beam, link beam of shear walls, ductility detailing of masonry structures, exits and staircases, and nonstructural elements, etc. are carried out. Suggestions for improving the seismic design of structures are also proposed. It is concluded that the seismic performance objectives for three earthquake levels, i.e., ＂no failure under minor earthquake level, ＂＂repairable damage under moderate earthquake level＂ and ＂no collapse under major earthquake level＂ can be achieved if seismic design principles are carried out by strictly following the code requirements and ensuring construction quality.     

Field investigation on severely damaged aseismic buildings in 2014 Ludian earthquake

The 2014 magnitude 6.5 Ludian earthquake caused a death toll of 617, many landslides and tens of thousands of collapsed buildings. A field investigation to evaluate the damage to buildings was carried out immediately after the occurrence of the earthquake. Severely damaged aseismic buildings, which were basically observed in the downtown of Longtoushan Town, were carefully examined one by one with the aim to improve design codes. This paper summarizes the damage observed to the investigated aseismic buildings in both the structural and local levels. A common failure mode was observed that most of the aseismic buildings, such as RC frame structures and confined masonry structures, were similarly destroyed by severe damage or complete collapse of the first story. The related strong ground motion, which was recorded at the nearby station, had a short duration of less than 20 s but a very large PGA up to 1.0 g. The RC frames based on the new design codes still failed to achieve the design target for "strong column, weak beam". Typical local failure details, which were related to the interaction between RC columns and infill walls and between constructional columns and masonry walls, are summarized with preliminary analyses.     

Introspection on improper seismic retrofit of Basilica Santa Maria di Collemaggio after 2009 Italian earthquake

The 2009 L’Aquila, Italy earthquake highlighted the seismic vulnerability of historic masonry building structures due to improper "strengthening" retrofit work that has been done in the last 50 years. Italian seismic standards recommend the use of traditional reinforcement techniques such as replacing the original wooden roof structure with new reinforced concrete (RC) or steel elements, inserting RC tie-beams in the masonry and new RC floors, and using RC jacketing on the shear walls. The L’Aquila earthquake revealed the numerous limitations of these interventions, because they led to increased seismic forces (due to greater additional weight) and to deformation incompatibilities of the incorporated elements with the existing masonry walls. This paper provides a discussion of technical issues pertaining to the seismic retrofit of the Santa Maria di Collemaggio Basilica and in particular, the limitations of the last (2000) retrofit intervention. Considerable damage was caused to the church because of questionable actions and incorrect and improper technical choices.     

Seismic damage to structures in the M_s6.5 Ludian earthquake

On 3 August 2014,the Ludian earthquake struck northwest Yunnan Province with a surface wave magnitude of 6.5.This moderate earthquake unexpectedly caused high fatalities and great economic loss.Four strong motion stations were located in the areas with intensity V,VI,VII and IX,near the epicentre.The characteristics of the ground motion are discussed herein,including 1)ground motion was strong at a period of less than 1.4 s,which covered the natural vibration period of a large number of structures;and 2)the release energy was concentrated geographically.Based on materials collected during emergency building inspections,the damage patterns of adobe,masonry,timber frame and reinforced concrete(RC)frame structures in areas with different intensities are summarised.Earthquake damage matrices of local buildings are also given for fragility evaluation and earthquake damage prediction.It is found that the collapse ratios of RC frame and confined masonry structures based on the new design code are significantly lower than non-seismic buildings.However,the RC frame structures still failed to achieve the ‘strong column,weak beam' design target.Traditional timber frame structures with a light infill wall showed good aseismic performance.     

Seismic Hazard Matrix of Buildings in Yunnan

Seismologists have begun to investigate the earthquake damage and assess the economic losses on the spot in the Yunnan area since the earthquakes with Ms6.7 and Ms6.9 that occurred on the boundary between China and Myanmar west of Menglian county, Yunnan Province, on April 23, 1992. From 1992 to 2003, 50 destructive earthquakes occurred in Yunnan, and large amounts of data on seismic hazard have been accumulated. With focus on the major building structures, the paper makes statistical analysis on the earthquake damage ratio, loss ratio and seismic hazard index in the areas with different seismic intensity of the 50 events, and presents the seismic hazard matrix of buildings for the Yunnan area.     

Seismic fragility assessment of low-rise stone masonry buildings

Many historic buildings in old urban centers in Eastern Canada are made of stone masonry reputed to be highly vulnerable to seismic loads.Seismic risk assessment of stone masonry buildings is therefore the first step in the risk mitigation process to provide adequate planning for retrofit and preservation of historical urban centers.This paper focuses on development of analytical displacement-based fragility curves reflecting the characteristics of existing stone masonry buildings in Eastern Canada.The old historic center of Quebec City has been selected as a typical study area.The standard fragility analysis combines the inelastic spectral displacement,a structure-dependent earthquake intensity measure,and the building damage state correlated to the induced building displacement.The proposed procedure consists of a three-step development process:(1) mechanics-based capacity model,(2) displacement-based damage model and(3) seismic demand model.The damage estimation for a uniform hazard scenario of 2% in 50 years probability of exceedance indicates that slight to moderate damage is the most probable damage experienced by these stone masonry buildings.Comparison is also made with fragility curves implicit in the seismic risk assessment tools Hazus and ELER.Hazus shows the highest probability of the occurrence of no to slight damage,whereas the highest probability of extensive and complete damage is predicted with ELER.This comparison shows the importance of the development of fragility curves specific to the generic construction characteristics in the study area and emphasizes the need for critical use of regional risk assessment tools and generated results.     

Seismic design analysis of the country masonry school buildings in the meizoseismal area

Several reinforcing schemes are illustrated that are based on the loading characteristics of typical country masonry school buildings with sparsely spaced transversal walls and large depth. From the seismic damage observed following the Wenchuan Earthquake, the effects of reinforcing schemes, tie-columns and tie-beams on the seismic resistance of masonry buildings are analyzed. The concept of improving the ductility of these types of buildings is presented. Finally, some suggestions are proposed for the design of masonry buildings with sparsely spaced transversal walls and large depth.     

Building damage in Dujiangyan during Wenchuan Earthquake

A field damage survey of 1,005 buildings damaged by the Wenchuan Earthquake in Dujiangyan City was carried out and the resulting data was analyzed using the statistical method. It is shown that buildings that were seismically designed achieved the desired seismic fortification target; they sustained less damage than the non-seismically designed buildings. Among the seismically designed buildings investigated, RC frame buildings performed the best in terms of seismic resistance. Masonry buildings with a ground story of RC frame structure were the second best, and masonry buildings performed the worst. Considering building height, multistory buildings sustained more severe damage than high-rise buildings and 2- and 3-story buildings. Compared to residential buildings, public buildings, such as schools and hospitals, suffered more severe damage.     

汶川地震房屋震害的一些现象分析

The MS8.0 Wenchuan earthquake caused a great deal of damage and collapse to engineering structures. Survey of disaster and engineering damage was made in detail by the authors and other researchers in the extreme earthquake disaster area. The paper makes an overview of the earthquake disaster status and damage phenomena which include brick-concrete buildings, frame structures, brick-wood structures, and timber frame residential buildings. Furthermore, the causes of the disaster and building damage phenomena are briefly discussed. In addition, some typical damage phenomena are specialized. According to the phenomena mentioned above, some feasible seismic measures are suggested for the development of buildings in future.     

Seismic fragility assessment of RC frame structure designed according to modern Chinese code for seismic design of buildings

Following several damaging earthquakes in China,research has been devoted to find the causes of the collapse of reinforced concrete(RC) building sand studying the vulnerability of existing buildings.The Chinese Code for Seismic Design of Buildings(CCSDB) has evolved over time,however,there is still reported earthquake induced damage of newly designed RC buildings.Thus,to investigate modern Chinese seismic design code,three low-,mid-and high-rise RC frames were designed according to the 2010 CCSDB and the corresponding vulnerability curves were derived by computing a probabilistic seismic demand model(PSDM).The PSDM was computed by carrying out nonlinear time history analysis using thirty ground motions obtained from the Pacific Earthquake Engineering Research Center.Finally,the PSDM was used to generate fragility curves for immediate occupancy,significant damage,and collapse prevention damage levels.Results of the vulnerability assessment indicate that the seismic demands on the three different frames designed according to the 2010 CCSDB meet the seismic requirements and are almost in the same safety level.     

Characteristics and Analysis of the Seismic Damage from the MS7.0 Jiuzhaigou Earthquake in the Area between Songpan and Jiuzhaigou

This paper expounds the features of the buildings and analyzes the seismic disaster characteristics of the Jiuzhaigou M_S7. 0 earthquake in the area between Songpan and Jiuzhaigou. New buildings (especially the frame structure) had good anti-seismic performance,but brick-wood structures and brick-concrete structures sustained large amounts of damage in the earthquake. By computing the seismic damage index,we found that the seismic damage index of the frame structure was far less than that of civil structures and brick-wood structures. The seismic damage index of frame structures were all zero in the Ⅵ area,and increased rapidly with the increase of intensity,but the increasing range was reduced. We also discussed how to evaluate the intensity in areas where there was a lack of buildings or there was only one structure type,which can be referenced in future field work.     

Design objectives and collapse prevention for building structures in mega-earthquake

A "mega-earthquake" is one with an intensity larger than the most severe earthquake intensity category currently considered in design codes. For a "mega-earthquake," the design objective of a given structure is to "preserve living spaces for people in the buildings." In this paper,factors that may influence the collapse resistance of RC frames in a mega-earthquake are analyzed based on seismic damage observed in the 2008 Wenchuan earthquake. Methodologies to improve structural collapse resistance focus on three aspects:global strength margin,global redundancy and global integration of the structural system. Fundamental principles and design concepts for collapse prevention under a mega-earthquake are proposed,and issues that need further research are identified.     

Shaking table tests and dynamic analyses of masonry wall buildings with frame-shear walls at lower stories

This paper describes shaking table tests of three eight-story building models： all are masonry structures in the upper stories, with or without frame-shear walls of one- or two- stories at the bottom. The test results of damage characteristics and seismic responses are provided and compared. Then, nonlinear response analyses are conducted to examine the reliability of the dynamic analysis. Finally, many nonlinear response analyses are performed and it is concluded that for relatively hard sites under a certain lateral stiffness ratio （i.e., the ratio of the stiffness of the lowest upper masonry story to that of the frame- shear wall story）, the masonry structure with one-story frame-shear wall at the bottom performs better than a structure built entirely of masonry, and a masonry structure with frame-shear wall of two stories performs better than with one-story frame- shear wall. In relatively soft soil conditions, all three structures have similar performane. In addition, some suggestions that could be helpful for design of masonry structures with ground story of frame-shear wall structure in seismic intensity region VII, such as the appropriate lateral stiffness ratio, shear force increase factor of the frame-shear wall story, and permissible maximum height of the building, are proposed.     

A comparative study of seismic provisions between International Building Code 2003 and Uniform Building Code 1997

This study focuses on the comparison of the Uniform Building Code （UBC） 1997 and International Building Code （IBC） 2003 in relation to the seismic design and analysis of special steel moment resisting frame buildings （SMRF）. This paper formulates a numerical study of a steel SMRF building, studied in four different situations, namely： as an office building in San Francisco; as an office building in Sacramento; as an essential facility in San Francisco, and as an essential facility in Sacramento. The analytical results of the model buildings are then compared and analyzed taking note of any significant differences. This case study explores variations in the results obtained using the two codes, particularly the design base shear and drift ratios as they relate to different locations and occupancy use. This study also proves that IBC 2003 is more stringent for the redundancy factor under design category E for the SMRF building, and drift limits for essential facilities.     

Seismic force demands on acceleration-sensitive nonstructural components: a state-of-the-art review

Nonstructural components(NSCs)are parts,elements,and subsystems that are not part of the primary loadbearing system of building structures but are subject to seismic loading.Damage to NSCs may disrupt the functionality of buildings and result in significant economic losses,injuries,and casualties.In past decades,extensive studies have been conducted on the seismic performance and seismic design methods of NSCs.As the input for the seismic design of NSCs,floor response spectra(FRS)have attracted the attention of researchers worldwide.This paper presents a state-of-the-art review of FRS.Different methods for generating FRS are summarized and compared with those in current seismic design codes.A detailed review of the parameters influencing the FRS is presented.These parameters include the characteristics of ground motion excitation,supporting building and NSCs.The floor acceleration response and the FRS obtained from experimental studies and field observations during earthquakes are also discussed.Three RC frames are used in a case study to compare the peak floor acceleration(PFA)and FRS calculated from time history analyses(THA)with that generated using current seismic design codes and different methods in the literature.Major knowledge gaps are identified,including uncertainties associated with developing FRS,FRS generation methods for different types of buildings,the need for comprehensive studies on absolute acceleration,relative velocity,and relative displacement FRS,and the calibration of FRS by field observations during earthquakes.     

Self-centering seismic retrofit scheme for reinforced concrete frame structures: SDOF system study

This paper presents the results of a parametric study of self-centering seismic retrofit schemes for reinforced concrete (RC) frame buildings. The self-centering retrofit system features flag-shaped hysteresis and minimal residual deformation. For comparison purpose,an alternate seismic retrofit scheme that uses a bilinear-hysteresis retrofit system such as buckling-restrained braces (BRB) is also considered in this paper. The parametric study was carried out in a single-degree-of-freedom (SDOF) system framework since a multi-story building structure may be idealized as an equivalent SDOF system and investigation of the performance of this equivalent SDOF system can provide insight into the seismic response of the multi-story building. A peak-oriented hysteresis model which can consider the strength and stiffness degradation is used to describe the hysteretic behavior of RC structures. The parametric study involves two key parameters -the strength ratio and elastic stiffness ratio between the seismic retrofit system and the original RC frame. An ensemble of 172 earthquake ground motion records scaled to the design basis earthquake in California with a probability of exceedance of 10% in 50 years was constructed for the simulation-based parametric study. The effectiveness of the two seismic retrofit schemes considered in this study is evaluated in terms of peak displacement ratio,peak acceleration ratio,energy dissipation demand ratio and residual displacement ratio between the SDOF systems with and without retrofit. It is found from this parametric study that RC structures retrofitted with the self-centering retrofit scheme (SCRS) can achieve a seismic performance level comparable to the bilinear-hysteresis retrofit scheme (BHRS) in terms of peak displacement and energy dissipation demand ratio while having negligible residual displacement after earthquake.     

Development of damage probability matrices based on Greek earthquake damage data

A comprehensive study is presented for empirical seismic vulnerability assessment of typical structural types, representative of the building stock of Southern Europe, based on a large set of damage statistics. The observational database was obtained from post-earthquake surveys carried out in the area struck by the September 7, 1999 Athens earthquake. After analysis of the collected observational data, a unified damage database has been created which comprises 180,945 damaged buildings from/after the near-field area of the earthquake. The damaged buildings are classified in specific structural types, according to the materials, seismic codes and construction techniques in Southern Europe. The seismic demand is described in terms of both the regional macroseismic intensity and the ratio αg/ao, where αg is the maximum peak ground acceleration (PGA) of the earthquake event and ao is the unique value PGA that characterizes each municipality shown on the Greek hazard map. The relative and cumulative frequencies of the different damage states for each structural type and each intensity level are computed in terms of damage ratio. Damage probability matrices (DPMs) and vulnerability curves are obtained for specific structural types. A comparison analysis is fulfilled between the produced and the existing vulnerability models.     

Seismic collapse simulation of existing masonry buildings with different retrofitting techniques

Masonry buildings are primarily constructed out of bricks and mortar which become discrete pieces and cannot sustain horizontal forces created by a strong earthquake.The collapse of masonry walls may cause significant human casualties and economic losses.To maintain their integrity,several methods have been developed to retrofit existing masonry buildings,such as the constructional RC frame which has been extensively used in China.In this study,a new method using precast steel reinforced concrete(PSRC)panels is developed.To demonstrate its effectiveness,numerical studies are conducted to investigate and compare the collapse behavior of a structure without retrofitting,retrofitted with a constructional RC frame,and retrofitted with external PSRC walls(PSRCW).Sophisticated finite element models(FEM)were developed and nonlinear time history analyses were carried out.The results show that the existing masonry building is severely damaged under occasional earthquakes,and totally collapsed under rare earthquakes.Both retrofitting techniques improve the seismic performance of existing masonry buildings.However,it is found that several occasional earthquakes caused collapse or partial collapse of the building retrofitted with the constructional RC frame,while the one retrofitted by the proposed PSRC wall system survives even under rare earthquakes.The effectiveness of the proposed retrofitting method on existing masonry buildings is thus fully demonstrated.     

A simplified methd of evaluating the seismic performance of buildings

This paper presents a simplified method of evaluating the seismic performance of buildings. The proposed method is based on the transformation of a multiple degree of freedom (MDOF) system to an equivalent single degree of freedom (SDOF) system using a simple and intuitive process. The proposed method is intended for evaluating the seismic performance of the buildings at the intermediate stages in design, while a rigorous method would be applied to the final design. The performance of the method is evaluated using a series of buildings which are assumed to be located in Victoria in western Canada, and designed based on the upcoming version of the National Building Code of Canada which is due to be published in 2005. To resist lateral loads, some of these buildings contain reinforced concrete moment resisting frames,while others contain reinforced concrete shear walls. Each building model has been subjected to a set of site-specific seismic spectrum compatible ground motion records, and the response has been determined using the proposed method and the general method for MDOF systems. The results from the study indicate that the proposed method can serve as a useful tool for evaluation of seismic performance of buildings, and carrying out performance based design.     

Seismic performance of high-rise buildings in selected regions in Saudi Arabia according to different seismic codes

The design code for each country is revised and updated based on an expected zone’s seismic intensities,geotechnical site classifications,structural systems,construction materials and methods of construction in order to provide more realistic considerations of seismic demand,seismic response,and seismic capacity.Based on the aforementioned provisions,structures designed according to different seismic codes may yield different performances for the same level of hazard.This study aims to investigate and compare the induced responses related to the earthquake-resistant design of reinforced concrete(RC)buildings according to the Saudi building code(SBC-301),American code(ASCE-7),uniform building code(UBC-97),and European code(EC-8).In order to account for the provision regarding the hazard specification and its effect on the induced seismic responses,four regions in the Kingdom of Saudi Arabia with different seismic levels are selected.The code provisions related to the specification of site classification and its effect on the induced design base shear are investigated as well.Significant differences are observed in the induced responses with the variation in seismic design codes for the considered seismic hazards and site classifications.