Hydrological controls of erosion and sediment transport in volcanic torrents

Abstract

Sediment is transported in the form of debris flows in major gullies dissecting permeable volcanic slopes as exemplified by the Kami-kamihori Valley in the northern Japan Alps. Four years of hydrological observations in the headwater area of the gully showed that the surface runoff which triggers debris flows is related to peak 10- to 20-minute rainfall. Sediment production in such a short time is not sufficient to prepare a debris flow. Therefore, debris must have been accumulated at a particular section by repeated sediment discharge due to minor rainstorms. The volume of the debris produced in the headwaters was evaluated and correlated to an effective rainfall. The quantity of sediment transport at seven sections along the gully by debris flows in three periods was evaluated through the measurement of the topographic changes. It was compared with the total effective rainfall for the pertinent period, and the mean “sediment concentration” in the debris flow was calculated for each section and for each period. It was shown that the change in the sediment concentration along the gully reflects the entrainment of debris from the gully floor in the acceleration zone and the deposition in the deceleration zone. It was also demonstrated that the sediment delivery of a debris flow depends on the time distribution of rainfall, because rainfall time bases appropriate to prediction of the sediment transport at different reaches vary.     

RELATION BETWEEN PRECIPITATION AND INITIATION OF DEBRIS FLOWS IN THE JIANGJIA RAVINE, YUNNAN PROVINCE, SOUTHWEST CHINA

1 INTRODUCTION In the watershed of the Jiangjia Ravine, the frequency of occurrence of rainstorms which can mobilize debris flows is high, and there are abundant unconsolidated materials deposited in the upstream area, these resulted in frequent eruption …     

A depth‐averaged two‐phase model for debris flows over erodible beds

Mass exchange between debris flow and the bed plays a vital role in debris flow dynamics. Here a depth‐averaged two‐phase model is proposed for debris flows over erodible beds. Compared to previous depth‐averaged two‐phase models, the present model features a physical step forward by explicitly incorporating the mass exchange between the flow and the bed. A widely used closure model in fluvial hydraulics is employed to estimate the mass exchange between the debris flow and the bed, and an existing relationship for bed entrainment rate is introduced for comparison. Also, two distinct closure models for the bed shear stresses are evaluated. One uses the Coulomb friction law and Manning's equation to determine the solid and fluid resistances respectively, while the other employs an analytically derived formula for the solid phase and the mixing length approach for the fluid phase. A well‐balanced numerical algorithm is applied to solve the governing equations of the model. The present model is first shown to reproduce average sediment concentrations in steady and uniform debris flows over saturated bed as compared to an existing formula underpinned by experimental datasets. Then, it is demonstrated to perform rather well as compared to the full set of USGS large‐scale experimental debris flows over erodible beds, in producing debris flow depth, front location and bed deformation. The effects of initial conditions on debris flow mass and momentum gain are resolved by the present model, which explicitly demonstrates the roles of the wetness, porosity and volume of bed sediments in affecting the flow. By virtue of extended modeling cases, the present model produces debris flow efficiency that, as revealed by existing observations and empirical relations, increases with initial volume, which is enhanced by mass gain from the bed. Copyright © 2017 John Wiley & Sons, Ltd.     

Vegetation and topographic controls on sediment deposition and storage on gully beds in a degraded mountain area

Active gully systems developed on highly weathered or loose parent material are an important source of runoff and sediment production in degraded areas. However, a decrease of land pressure may lead to a return of a partial vegetation cover, whereby gully beds are preferred recolonization spots. Although the current knowledge on the role of vegetation on reducing sediment production on slopes is well developed, few studies exist on the significance of restoring sediment transport pathways on the total sediment budget of degraded mountainous catchments. This study in the Ecuadorian Andes evaluates the potential of vegetation to stabilize active gully systems by trapping and retaining eroded sediment in the gully bed, and analyses the significance of vegetation restoration in the gully bed in reducing sediment export from degraded catchments. Field measurements on 138 gully segments located in 13 ephemeral steep gullies with different ground vegetation cover indicate that gully bed vegetation is the most important factor in promoting short‐term (1–15 years) sediment deposition and gully stabilization. In well‐vegetated gully systems ( ≥ 30% of ground vegetation cover), 0.035 m³ m^–1 of sediment is deposited yearly in the gully bed. Almost 50 per cent of the observed variance in sediment deposition volumes can be explained by the mean ground vegetation cover of the gully bed. The presence of vegetation in gully beds gives rise to the formation of vegetated buffer zones, which enhance short‐term sediment trapping even in active gully systems in mountainous environments. Vegetation buffer zones are shown to modify the connectivity of sediment fluxes, as they reduce the transport efficiency of gully systems. First calculations on data on sediment deposition patterns in our study area show that gully bed deposition in response to gully bed revegetation can represent more than 25 per cent of the volume of sediment generated within the catchment. Our findings indicate that relatively small changes in landscape connectivity have the potential to create strong (positive) feedback loops between erosion and vegetation dynamics. Copyright © 2009 John Wiley & Sons, Ltd.     

黄土高原大理河流域水沙耦合模型应用研究

水沙模型是定量描述水沙关系及水沙规律的重要工具,现阶段国内外对于水沙模型的研究大都为基于某个典型流域的经验统计模型或基于流域大量基础资料的物理模型,极大限制了其使用范围及模拟精度.本文建立了结构与参数均具有物理意义的流域水沙耦合物理概念模型,其优点是物理概念清楚,模拟精度高,实用性强,易于深入研究泥沙基本规律.该模型将概念性水文模型和泥沙模型耦合,提出水流挟沙能力和土壤抗侵蚀能力概念,用对数曲线近似描述流域土壤抗侵蚀能力的空间变异性,在拜格诺河道水流悬移质泥沙公式基础上建立概念性沟蚀产沙公式,参照水流汇集相似性建立泥沙汇集演算公式.选取黄河中游大理河流域4个不同流域尺度的实际流域对模型进行应用检验,模拟结果表明,该模型的水流泥沙两部分均有很高的模拟精度,可以很好地模拟黄河中游地区不同流域尺度和年际尺度上的洪水过程和泥沙产生及输移过程,充分证明了该模型结构、参数和计算方法的合理性,可用于定量分析流域内各项水保措施的减水减沙效益及水沙关系变化趋势,对该模型的推广应用可做进一步分析研究.     

Large wood inhibits debris flow runout in forested southeast Alaska

Due to their potentially long runout, debris flows are a major hazard and an important geomorphic process in mountainous environments. Understanding runout is therefore essential to minimize risk in the near-term and interpret the pace and pattern of debris flow erosion and deposition over geomorphic timescales. Many debris flows occur in forested landscapes where they mobilize large volumes of large woody debris (LWD) in addition to sediment, but few studies have quantitatively documented the effects of LWD on runout. Here, we analyze recent and historic debris flows in southeast Alaska, a mountainous, forested system with minimal human alteration. Sixteen debris flows near Sitka triggered on August 18, 2015 or more recently had volumes of 80 to 25 000 m³ and limited mobility compared to a global compilation of similarly-sized debris flows. Their deposits inundated 31% of the planimetric area, and their runout lengths were 48% of that predicted by the global dataset. Depositional slopes were 6°–26°, and mobility index, defined as the ratio of horizontal runout to vertical elevation change, ranged from 1.2 to 3, further indicating low mobility. In the broader southeast Alaskan region consisting of Chichagof and Baranof Islands, remote sensing-based analysis of 1061 historic debris flows showed that mobility index decreased from 2.3–2.5 to 1.4–1.8 as average forest age increased from 0 to 416 years. We therefore interpret that the presence of LWD within a debris flow and standing trees, stumps, and logs in the deposition zone inhibit runout, primarily through granular phenomena such as jamming due to force chains. Calibration of debris flow runout models should therefore incorporate the ecologic as well as geologic setting, and feedbacks between debris flows and vegetation likely control the transport of sediment and organic material through steep, forested catchments over geomorphic time. © 2020 John Wiley & Sons, Ltd.     

Loess erosion change modeling during heavy rainfall

A typical gully sub-basin with a complex geomorphological form is used to do a model test of gravity erosion of loess by considering the sequence of slopes in a prototype gully creating a sequence of underlying surface forms in the upper reaches. The results show that the runoff from heavy rainfall is the main external force for the erosion of loess, and also is an important influencing factor to stimulate and intensify the development of gravity erosion. The soil structure and the height of the...     

Tributary confluences and discontinuities in channel form and sediment texture: Rio Chama,NM

Numerous morphological changes can occur where two channels of distinct sediment and flow regimes meet, including abrupt shifts in channel slope, cross‐sectional area, planform style, and bed sediment size along the receiving channel. Along the Rio Chama between El Vado and Abiquiu Dams, northern New Mexico, arroyo tributaries intermittently deliver sediment from erodible sandstone and shale canyon walls to the mainstem channel. Much of the tributary activity occurs in flash floods and debris flows during summer thunderstorms, which often load the channel with sand and deposit coarser material at the mainstem confluence. In contrast, mainstem channel flow is dominated by snowmelt runoff. To examine tributary controls, we systematically collected cross‐section elevation and bed sediment data upstream and downstream of 26 tributary confluences along a 17 km reach. Data from 203 cross‐sections were used to build a one‐dimensional hydraulic model for comparing estimated channel parameters at bankfull and low‐flow conditions at these sites As compared to intermediate reaches, confluences primarily impact gradient and bed sediment size, reducing both parameters upstream of confluences and increasing them downstream. Cross‐section area is also slightly elevated above tributary confluences and reduced below. Major shifts in slope and bed sediment size at confluences appear to drive variations in sediment entrainment and transport capacity and the relative storage of sand along the channel bed. The data were analyzed and compared to models of channel organization based on lateral inputs, such as the Network Variance Model and the Sediment Link Concept. At a larger scale, hillslope ? channel coupling increases in the downstream third of the study reach, where the canyon narrows, resulting in steeper slopes and more continuous coarse bed material along the mainstem, and thus, limiting the contrast with tributary confluences. However, channel form and sediment characteristics are highly variable along the study reach, reflecting variations in the size and volume of sediment inputs related to the surface geology in tributary watersheds, morphology of the Rio Chama at the junction (i.e. bends, confinement), and the relative magnitude and location of past depositional events. Copyright © 2014 John Wiley & Sons, Ltd.     

Bed scour by debris flows: experimental investigation of effects of debris‐flow composition

Debris flows can grow greatly in size by entrainment of bed material, enhancing their runout and hazardous impact. Here, we experimentally investigate the effects of debris‐flow composition on the amount and spatial patterns of bed scour and erosion downstream of a fixed to erodible bed transition. The experimental debris flows were observed to entrain bed particles both grain by grain and en masse, and the majority of entrainment was observed to occur during passage of the flow front. The spatial bed scour patterns are highly variable, but large‐scale patterns are largely similar over 22.5–35° channel slopes for debris flows of similar composition. Scour depth is generally largest slightly downstream of the fixed to erodible bed transition, except for clay‐rich debris flows, which cause a relatively uniform scour pattern. The spatial variability in the scour depth decreases with increasing water, gravel (= grain size) and clay fraction. Basal scour depth increases with channel slope, flow velocity, flow depth, discharge and shear stress in our experiments, whereas there is no correlation with grain collisional stress. The strongest correlation is between basal scour and shear stress and discharge. There are substantial differences in the scour caused by different types of debris flows. In general, mean and maximum scour depths become larger with increasing water fraction and grain size, and decrease with increasing clay content. However, the erodibility of coarse‐grained experimental debris flows (gravel fraction = 0.64) is similar on a wide range of channel slopes, flow depths, flow velocities, discharges and shear stresses. This probably relates to the relatively large influence of grain‐collisional stress to the total bed stress in these flows (30–50%). The relative effect of grain‐collisional stress is low in the other experimental debris flows (<5%), causing erosion to be largely controlled by basal shear stress. Copyright © 2016 John Wiley & Sons, Ltd.     

DEBRIS FLOW CONTROL BY USING SLIT DAMS

1 INTRODUTIONTaiwan is a hilly-mountainous island lying across the center of the tropic. The slopeland accounts fortwo thirds of the total area of Taiwan. Most mountains are consisted of geologically young rocks incategories of fissile slates and shales which are easily eroded by weather. TOrrents combined with fissileslates and shales form debris flows with a very strong destrUctive power. This kind of debris flow canpotentially occur for almost all torrents whose gradient is steeper th…     

STEP-POOL MORPHOLOGY IN HIGH-GRADIENT STREAMS

l 1NTRODUCTIONGravel bed rivers are found in man parts of the worid, mpically in moUntainous regions with highgradients and seasonally high flows. These rivers are imPotalt in contrlling flood waters from sPringrunoff in regions such as the Pacific Northwest, Where heaVy snowfall can be followed by equally heaVyranfall. The combination of high stream gradient and high discharge causes significant erosion of thebed and bank of the strCam, in some cases moving large boulders with ease.It…     

Paraglacial modification of slope form

The morphological consequences of paraglacial modification of valley-side drift slopes are investigated at six sites in Norway. Here, paraglacial slope adjustment operates primarily through the development of gully systems, whereby glacigenic sediment is stripped from the upper drift slope and redeposited in debris cones downslope. This results in an overall lowering of average gradient by up to 4·5° along gully axes. In general, slope profile adjustment appears to be characterized by a convergence of slope profiles towards an ‘equilibrium form’ with an upper rectilinear slope gradient at 29°± 4° and a range of concavities of approximately 0·0 to 0·4. After initial rapid incision, further gully deepening is limited, but gullies become progressively wider as sidewall gradients decline to c. 25°, after which parallel retreat appears to predominate. The final form of mature paraglacial gully systems consists of an upper bedrock-floored source area, a mid-slope area of broad gullies whose sidewalls rest at stable, moderate gradients, and a lower slope zone where gullies discharge onto the surfaces of debris cones and fans. Some gullies appear to have attained this final form and have stabilized following exhaustion of readily entrainable sediment within decades of gully initiation. At most sites, paraglacial activity has transformed steep drift-mantled valley sides into gullied slopes where an average of c. 2–3 m of surface lowering has taken place. At the most active sites, these average amounts imply minimum erosion rates averaging c. 90 mm a⁻¹ since gully initiation, which highlights the extreme rapidity of paraglacial erosion of deglaciated drift-mantled slopes. Copyright © 1999 John Wiley & Sons, Ltd.     

Suspended sediment transport regime in a debris‐flow gully on Vancouver Island,British Columbia

In debris‐flow‐prone channels, normal fluvial sediment transport occurs (nearly exclusively in suspended mode) between episodic debris‐flow events. Observations of suspended sediment transport through a winter season in a steepland gully in logged terrain revealed two event types. When flows exceeded a threshold of 270 l s⁻¹, events yielded significant quantities of sediment and suspended sediment concentration increased with flow. Smaller events were strongly ‘supply limited’; sediment concentration decreased as flow increased. Overall, there is no consistent correlation between runoff and sediment yield. Within the season, three subseasons were identified (demarcated by periods of freezing weather) within which a pattern of fine sediment replenishment and evacuation occurred. Finally, a signature of fine sediment mobilization and exhaustion was observed within individual events. Fine sediment transport occurred in discrete pulses within storm periods, most of the yield occurring within 5 to 15% of storm runoff duration, so that it is unlikely that scheduled sampling programs would identify significant transport. Significant events are, however, generally forecastable on the basis of regional heavy rainfall warnings, providing a basis for targeted observations. Radiative snowmelt events and rain‐on‐snow remain difficult to forecast, since the projection of temperatures from the nearest regular weather station yields variable results. Copyright © 2004 John Wiley & Sons, Ltd.     

General velocity formula of boundary layer above mobile sediment bed induced by asymmetric waves

Sediment movement in the wave boundary layer above a mobile sediment bed is complex.A velocity formula for the boundary layer is proposed for sheet flow induced by asymmetric waves above a mobile sediment bed.The formula consists of a free stream velocity and a defect function which contains a phase-lead,boundary layer thickness and mobile sediment bed.Phase-lag of sediment movement is considered in the formula for the mobile sediment bed.The formula needs six dependent variables about asymmetric wave and sediment characteristics.Asymmetry effects on parameters(orbital amplitude,roughness height,bed shear stress,and boundary layer thickness)are properly considered such that the formula can yield velocity differences among onshore,offshore,acceleration,and deceleration stages.The formula estimates the net boundary layer velocity resulting from the mobile sediment bed and asymmetric boundary layer thickness.In addition,a non-constant phase-lead also contributes to the net boundary layer velocity in asymmetric oscillatory sheet flow.Results of the formula are as good as that of a two-phase numerical model.Sheet flow transport induced by asymmetric waves,and the offshore net sediment transport rate with a large phase-lag under velocity-skewed waves,can be adequately estimated by the formula with a power sediment concentration function.     

The impact of flow discharge on the hydraulic characteristics of headcut erosion processes in the gully region of the Loess Plateau

Headcut erosion is associated with major hydraulic changes induced by the gully head of concentrated flow. However, the variation in the hydraulic characteristics of the headcut erosion process is still not clear in the gully region of the Loess Plateau. A series of rainfall combined scouring experiments (flow discharges ranging from 3.6 to 7.2 m³ hr⁻¹, with 0.8 mm min⁻¹ rainfall intensity) were conducted on experimental plots to clarify the variation in the hydraulic parameters induced by gully head and erosion processes under different flow discharges. The results showed that concentrated flows in the catchment area and gully bed were turbulent (Reynolds number ranging from 1,876 to 6,693) and transformed between supercritical and subcritical (Froude number ranging from 0.96 to 3.73). The hydraulic parameters, such as the flow velocity, Reynolds number, shear stress, stream power, Darcy–Weisbach friction factor, and unit stream power in the catchment area were 0.45–0.59 m s⁻¹, 2086–6693, 1.96–5.33 Pa, 0.89–2.86 W m⁻², 0.08–0.16, and 0.023–0.031 m s⁻¹, respectively. When the concentrated flows dropped from the gully head, the hydraulic parameters in the gully bed decreased by 3.39–26.07%, 1.49–29.99%, 65.19–67.14%, 67.25–74.96%, 28.53–61.31%, and 67.82–77.14%, respectively, which contributed to the flow energy consumption at the gully head. As flow discharge increased, Reynolds number, shear stress, and stream power increased, while flow velocity, Froude number, unit stream power, and Darcy–Weisbach friction factor did not. The flow energy consumption at the gully head was 9.66–10.13, 13.25–13.74, 15.68–16.41, and 19.28–20.25 J s⁻¹, respectively, under different flow discharges and accounted for 60.58–68.50% of the flow energy consumption of the experimental plots. Generally, the sediment discharges increased rapidly at the initial stage, then increased slowly, and finally reached a steady state condition, which showed a significant declining logarithmic trend with experimental duration (P<.01) and increased with increasing flow discharge. Accordingly, the flow energy consumption was significantly correlated with the sediment yield. These findings could improve our understanding of the hydraulic properties and flow energy characteristics of headcut erosion.     

Erosion and deposition by debris flows at Mt Thomas,North Canterbury,New Zealand

The grass-covered slopes on the southern flank of Mt Thomas, an upfaulted block of highly sheared sandstone and argillite 40 km NW of Christchurch, New Zealand, are presently undergoing severe erosion by a combination of mass-wasting processes. Gully erosion, soil slips, and debris flows have carved out a number of steep, deeply incised ravines, from which coarse debris is transported (primarily by debris flows) to alluvial fans below. Geologic and historical evidence indicates that debris flows have been episodically active here for at least the last 20,000 years and have been the dominant process in fan building. This demonstrates that catastrophic geomorphic processes, rather than processes acting at relatively uniform rates, can be dominant in humid-temperate areas as well as in arid and semi-arid regions. In April 1978, debris flows were triggered in one of two unstable ravines in the Bullock Creek catchment by a moderate intensity, long duration rainstorm with a return period in excess of 20 years. Surges of fluid debris, moving at velocities up to 5 m/s, transported a dense slurry of gravel, sand, and mud up to 3·5 km over a vertical fall of 600 m. Deposition on the alluvial fan occurred when the flows left the confines of an entrenched fan-head channel and spread out as a 0·16 km² sheet averaging 1·2 m thick. In all, 195,000 m³ were deposited, roughly a third of that being reworked sediments from the head of the fan. Sediment yield from this one event would be equivalent to several thousand years worth of erosion at average sediment discharge rates for small South Island mountain catchments. Samples of viscous fluid debris during surges contained up to 84 per cent solids, composed of 70 per cent gravel, 20 per cent silt, and 4 per cent clay. Fluid density of the material ranged between 1·95 and 2·13 g/cm³, and it was extremely poorly sorted. Between surges the fluid was less viscous, less dense, and unable to carry gravel in suspension. Severe fan-head entrenchment of the stream channel (approximately 10 m in less than 24 hours) was accomplished by the erosive action of the surges. Tectonic uplift of the Mt Thomas block and the weak, crushed condition of the bedrock appear to be ultimately responsible for the catastropic erosion of slopes in the Bullock Creek catchment. However, forest clearing within the last few centuries appears to have greatly increased the rate of mass wasting and gully erosion on these slopes.     

The role of the sediment budget in understanding debris flow susceptibility

This study proposes a sediment‐budget model to predict the temporal variation of debris volume stored in a debris‐flow prone watershed. The sediment‐budget is dominated by shallow landslides and debris outflow. The basin topography and the debris volume stored in the source area of the debris‐flow prone watershed help evaluating its debris‐flow susceptibility. The susceptibility model is applied to the Tungshih area of central western Taiwan. The importance of the debris volume in predicting debris‐flow susceptibility is reflected in the standardized coefficients of the proposed statistical discriminant model. The high prediction rate (0·874) for the occurrence of debris flows justifies the capability of the proposed susceptibility models to predict the occurrence of debris flows. This model is then used to evaluate the temporal evolution of the debris‐flow susceptibility index. The analysis results show that the numbers of watershed which are classified as a debris‐flow group correspond well to storage of sediment at different time periods. These numbers are 10 before the occurrence of Chi‐Chi earthquake, 13 after the occurrence of Chi‐Chi earthquake, 16 after the occurrence of landslides induced by Typhoon Mindulle (Typhoon M), and 14 after the occurrence of debris flows induced by Typhoon M. It indicates that the occurrence of 7·6 Chi‐Chi earthquake had significant impact on the debris flow occurrence during subsequent typhoons. Copyright © 2009 John Wiley & Sons, Ltd.     

青海加吾矿区玛日当沟泥石流流域分区与动力特征分析

加吾矿区地处青藏高原区内柴达木盆地东缘区的青海南山微造山带内,为保障该区矿产资源勘查及开采工作的顺利进行,有效预防矿区内泥石流等突发性地质灾害的发生。通过开展矿区泥石流灾害详查工作,尤其是针对矿区重点工作区玛日当沟流域进行了系统的调查,建立了对该流域泥石流灾害发育背景的充分认识,并对该流域泥石流分区特征作了系统描述。在此基础上,依据青海省同德县气象观测资料,对玛日当沟泥石流动力特征作了详细分析。结果显示,矿区玛日当沟为标准型泥石流沟,流域分区特征显著,具备了泥石流形成的有利条件。计算表明,该流域十年一遇、二十年一遇、五十年一遇、一百年一遇以及两百年一遇的泥石流峰值流量分别为54.19 m~3/s、76.23 m~3/s、129.51 m~3/s、196.03 m~3/s、278.86 m~3/s。     

Variability in rainfall threshold for debris flow after the Chi-Chi earthquake in central Taiwan, China

The purpose of this study is to analyze variability in rainfall threshold for debris flow （critical rainfall for debris flow triggering） after the ML 7.3 Chi-Chi earthquake in central Taiwan in 1999. Two study sites with different geological conditions were surveyed in the earthquake area. Streambed surveys were conducted to continuously monitor debris flows between 1999 and 2006. During the 7-year study period, every debris flow event was identified, and the streambed characterized. Results show that the rainfall threshold for debris flow was remarkably lower just after the Chi-Chi Earthquake, but gradually recovered. To date, this rainfall threshold is still lower than the original level prior to the earthquake. This variability in rainfall threshold is closely related to the mount of sediment material in the initiation area of debris flow, which increased rapidly due to landslides resulting from the earthquake. With the increase in sediment material, the rainfall threshold was lowered severely during the first year following the Chi-Chi earthquake. However, heavy rainfalls mobilized the sediment material, causing debris flows and transporting sediment downstream. With the decrease in sediment material, the rainfall threshold recovered gradually over time. Furthermore, debris flows occurred only in the subbasins that had sufficient sediment material to cause significant movement. Hence, these results confirm that the sediment material in the initiation area of debris flow is a crucial component of the rainfall threshold for debris flow.     

ENTRAINMENT FUNCTION OF SUSPENDED SEDIMENT IN OPEN CHANNELS

1　ＩＮＴＲＯＤＵＣＴＩＯＮ　Ｒｉｖｅｒｆｌｏｗｓｗｉｔｈｓｕｓｐｅｎｄｅｄｓｅｄｉｍｅｎｔｓａｒｅａｍｏｎｇｔｈｅｍｏｓｔｉｍｐｏｒｔａｎｔｆａｃｔｏｒｓａｆｆｅｃｔｉｎｇｔｈｅｇｅｏｍｏｒｐｈｉｃｅｖｏｌｕｔｉｏｎ.Ａｋｅｙｆｅａｔｕｒｅｏｆｔｈｉ...