Trace Element Analysis of Fused Whole-Rock Glasses by Laser Ablation-ICP-MS and PIXE

The concentrations of fifty trace elements, including relatively volatile elements and transition metal elements, in fused glasses of Geological Survey of Japan rock reference materials GSJ JR-2, JA-1, JA-2, JB-1a, JB-3, JGb-1 and JF-1 were determined by particle (proton) induced X-ray emission (PIXE) and laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS). The fused glasses were prepared by rapid fusion and subsequent quenching in welded platinum capsules and were found to be homogeneous for major elements and for trace elements with concentrations of more than 1 μg g^-1 within the observed precision (± 10% mean) on a 70 μm sampling scale. The values obtained by PIXE and LA-ICP-MS for the transition elements (Cr, Mn, Fe, Ni and Cu), the relatively volatile elements (Zn, Ga, Rb and Pb) and the refractory elements (Y, Zr, Nb and Th) with concentrations greater than a few μg g^-1 showed good agreement (within 10 % relative difference). The values for almost all the elements detected at concentrations higher than 1 μg g^-1 as determined by LA-ICP-MS also agreed well with the reference values (mean relative difference < ± 10%), except for B and Cu. The good agreement confirmed the appropriateness of the NIST SRM 600 series glass calibration reference material for LA-ICP-MS analysis of glasses with variable major-element compositions for almost all elements. The concentrations of Cu in all the samples were lower than the reference values, which was attributed to adsorption of the transition metals onto the platinum capsule during preparation.     

Concentrations of Trace Elements in Carbonate Reference Materials Coral JCp-1 and Giant Clam JCt-1 by Inductively Coupled Plasma-Mass Spectrometry

Trace elements in the Geological Survey of Japan carbonate reference materials Coral JCp-1 and Giant Clam JCt-1 were determined by inductively coupled plasma-mass spectrometry after digestion with 2% v/v HNO₃. A standard addition method was adopted in this determination in order to neutralise the Ca matrix effect. In addition, Sc, Y, In and Bi were used as internal standards to control the matrix effect and correct instrumental drift. Of the eighteen elements measured in JCp-1, precisions for fourteen elements, including Cu, Cd and Ba, were better than 10% RSD and concentrations ranged from 0.002 μg g^-1 (Cs) to 8.02 μg g^-1 (Ba). The concentrations of measured trace elements in JCt-1, except for Cu, were lower than those in JCp-1. Precisions for all elements with concentrations higher than 0.04 μg g^-1 in JCt-1 were also better than 10% RSD and concentrations were found to be between 0.001 μg g^-1 (Cs) and 4.84 μg g^-1 (Ba). The concentrations of more than fifteen trace elements in the aragonite reference materials are reported here for the first time. Both reference materials are suitable for use in geochemical studies of environmental reconstruction based upon biogenic carbonate materials.     

Ion Chromatographic Determination of Fluorine and Chlorine in Silicate Rocks Following Alkaline Fusion

A simple and accurate method to determine fluorine and chlorine contents in small amounts (∼ 30 mg) in rock has been developed using ion chromatography after extraction by alkaline fusion. Powdered sample was mixed with sodium carbonate and zinc oxide at a mass ratio of 1:3:1, and was fused in an electric furnace at 900 °C for 30-40 minutes. An aqueous solution obtained by dissolving the fused silicate rock was diluted to the appropriate concentration of sodium carbonate (< ∼ 24 mmol l^-1) to minimise the tailing effect on F^- during ion chromatography caused by the large amount of carbonate species originating from the flux. Fluorine and chlorine contents were then determined by a standard additions method. Based on the relative standard deviation of the backgrounds, detection limits of both fluorine and chlorine were ∼ 4 μg g^-1, when 30 mg test portions were fused and diluted by a factor of 1200. We also report new fluorine and chlorine contents in nine GSJ (Geological Survey of Japan) reference materials, including peridotite (JP-1), granite (JG-1a), basalts (JB-1b, 2 and 3), andesites (JA-1 and 2) and rhyolites (JR-1 and 2). Fluorine and chlorine contents in the reference materials in this study were consistent with previously reported values. Reproducibilities were < 10 % for samples with F and Cl concentrations of > 20 μg g-1 and < 20 % with F and Cl < 20 μg g^-1.     

Analysis of Re, Au, Pd, Pt and Rh in NIST Glass Certified Reference Materials and Natural Basalt Glasses by Laser Ablation ICP-MS

A new technique for the in situ analysis of Re, Au, Pd, Pt and Rh in natural basalt glass by laser ablation (LA)-ICP-MS is described. The method involves external calibration against NIST SRM 612/613 or 614/615 glass certified reference materials, internal standardisation using Ca, and ablation with a 200 μm wide beam spot and a pulsed laser repetition rate of 50 Hz. Under these conditions, sensitivities for Re, Au, Pd, Pt and Rh analyte ions are ˜ 5000 to 100,000 cps/μg g^-1. This is sufficient to make measurements precise to ˜ 10% at the 2-10 μg g^-1 level, which is well within the range of concentrations expected in many basalts. For LA-ICP-MS calibration and a demonstration of the accuracy of the technique, concentrations of Re, Au, Pd, Pt and Rh in the NIST SRM 610/611 (˜ 1 to 50 μg g^-1), 612/613 (˜ 1 to 7 μg g^-1), 614/615 (˜ 0.2 to 2 μg g^-1) and 616/617 (˜ 0.004 to 2 μg g^-1) glasses were determined by solution-nebulisation (SN)-ICP-MS. Using the 612/613 or 614/615 glasses as calibration standards, LA-ICP-MS measurements of these elements in the other NIST glasses fell within ˜ 15% of those determined by SN-ICP-MS. Replicate LA-ICP-MS analyses of the 612/613 and 614/615 glasses indicate that, apart from certain anomalous domains, the glasses are homogeneous for Re, Au, Pd, Pt and Rh to better than 3.5%. Two LA-ICP-MS analyses of natural, island-arc basalt glasses exhibit large fractionations of Re, Au and Pd relative to Pt and Rh, compared to the relative abundances in the primitive mantle.     

Flotation Separation of Trace Elements from Alkaline-Earth Matrices by Co(III) Hexamethylenedithiocarbamate before ICP-AES Determination

A method for the selective separation of Ag, Cd, Cr, Cu, Ni, Pb and Zn in traces from solutions of calcite (CaCO₃), dolomite (CaMg(CO₃)₂) and gypsum (CaSO₄.2H₂O) before their determination by inductively coupled plasma-atomic emission spectrometry (ICP-AES) is presented. The expected interferences of Ca and Mg on intensities of trace analytes were removed by collecting the elements of interest with cobalt(III) hexamethylenedithiocar-bamate, Co(HMDTC)₃. The flotation of aqueous solutions (1 l) of calcite, dolomite and gypsum was performed at pH 6.0, by 1.5 mg l⁻¹ Co and 0.6 mmol l⁻¹ HMDTC⁻. To minimise the effect of the reaction between Ca/Mg, which restrains the function of the surfactant, careful selection of the most suitable foaming reagent was necessary. The accuracy of the method was established by analysing natural alkaline-earth minerals by the standard addition method as well as using the dolomite reference materials GBW 07114 and GSJ JDo-1. The ICP-AES limits of detection following flotation on different minerals were found to be 0.080 μg g⁻¹ for Cd, 0.105 μg g⁻¹ for Ag, 0.142 μg g⁻¹ for Cu, 0.195 μg g⁻¹ for Cr, 0.212 μg g⁻¹ for Ni, 0.235 μg g⁻¹ for Zn and 0.450 μg g⁻¹ for Pb.     

Precise Determination of Ultra-Low (sub-ng g-1) Level Rare Earth Elements in Ultramafic Rocks by Quadrupole ICP-MS

We present a new method that determines precisely and accurately rare earth elements (REE) at the sub-ng g^-1 level in ultramafic rocks based on acid dissolution and quadrupole ICP-MS with systematic interference corrections on each sample. The method is demonstrated by analyses of the international geochemical reference materials, PCC-1 (peridotite), DTS-1 (dunite) and DTS-2 (dunite) provided by the United States Geological Survey (USGS), and JP-1 (peridotite) issued by the Geological Survey of Japan (GSJ). Detection limits, as rock equivalent, were calculated to be 0.01-0.08 ng g^-1 for our instrument, which is sufficiently low compared to the REE concentrations of ultramafic rocks. In addition, procedural blanks of the proposed method were 0.2-5 pg, which is negligible even for the ultra-low level REE determinations. Reproducibility obtained from separate dissolutions and measurements of USGS DTS-2 and GSJ JP-1 was 3-6%, which corresponds to the high-precision data obtained by ID-TIMS or magnetic sector field ICP-MS with a desolvating nebuliser. The REE data determined exhibit smooth chondrite-normalised REE patterns for all of the tested geochemical reference materials, and the abundances are in good agreement with recently published data.     

FeSO4稳定铬污染土的铬赋存形态及浸出特性研究

采用硫酸亚铁（FeSO4）对Cr(VI)污染土进行稳定化处理。研究了Fe(II)/Cr(VI)摩尔比和养护龄期对污染土稳定过程中的铬赋存形态及浸出特性的影响规律。结果表明：随着Fe(II)/Cr(VI)摩尔比和养护龄期的增加,Cr(VI)和总Cr的浸出浓度降低,稳定土中Cr(VI)的含量降低,当摩尔比为3时,Cr(VI)和总Cr的浸出浓度均低于我国《危险废弃物鉴别标准 浸出毒性鉴别》（GB/T50853―2007）的限值;当摩尔比为10时,稳定土中Cr(VI)的含量低于我国《土壤环境质量标准》（GB15618―2008）中工业和商业用地的限值（30 mg/kg）;当摩尔比为20时,低于居住用地限值（5 mg/kg）。形态提取试验结果表明：FeSO4改变稳定土中铬的赋存形态,可促使铬从弱酸态向可还原态和可氧化态转化,而对残渣态的铬影响不大。Cr(VI)的浸出浓度与稳定土中的Cr(VI)含量均存在指数函数关系,且浸出试验不能全面、客观地评价铬污染土稳定效果。     

Ultra-Trace Element Analysis of NIST SRM 616 and 614 using Laser Ablation Microprobe-Inductively Coupled Plasma-Mass Spectrometry (LAM-ICP-MS): a Comparison with Secondary Ion Mass Spectrometry (SIMS)

The microanalytical capability of laser ablation microprobe-inductively coupled plasma-mass spectrometry (LAM-ICP-MS) to determine ultra trace elemental concentrations has been demonstrated by the analysis of two low concentration glass standard reference materials, NIST SRM 614 and 616. Results for fifty two elements at concentrations in the low ng g^-1 range are compared with those determined using secondary ion mass spectrometry (SIMS). Both techniques provide results at these concentrations that generally agree within 95% confidence limits, demonstrating the accuracy for ultra-trace level of in situ determinations by the two techniques. At concentrations of less than 20 ng g^-1 in NIST SRM 616, an accuracy and precision of better than 10% has been obtained for most mono-isotopic rare earth elements, when a spot size of 50 μm is used. Limits of detection for selected elements were as low as 0.5 ng g^-1.     

Preliminary Investigation into the Use of a High Resolution Inductively Coupled Plasma-Mass Spectrometer with Laser Ablation for Bulk Analysis of Geological Materials Fused with Li2B4O7

The paper presents preliminary results of the use of a high resolution double-focussing, magnetic sector inductively coupled plasma-mass spectrometer (HR-ICP-MS) with ultraviolet laser ablation (LA) for the bulk analysis of geological materials fused with Li₂B₄O₇. Detection limits are based on data from precision measurements of a fused SiO₂ sample of high purity, and sensitivity data (cps/μg g^-1) obtained on the Reference Material (RM) Syenite SY-2. For many trace elements, the detection limits are better than 0.05 μg g^-1 using a sample to flux weight ratio of 1:7.
Calibration curves, which are based entirely on RMs, are established for Hf, Ta, Tb, Tm and Lu. They indicate that, even at this early stage in the development of the technique, data accurate to ˜ 25% can be collected. It is concluded that the method may prove to be a valuable supplement to XRF for low level element concentration measurements; it is also very practical, as the same sample discs can be used for both XRF and LA-ICP-MS analyses.     

Determination of the Platinum-Group Elements and Gold in Twenty Rock Reference Materials by Inductively Coupled Plasma-Mass Spectrometry (ICP-MS) after Pre-Concentration by Nickel Sulfide Fire Assay

The platinum-group elements (PGE) and gold have been determined in twenty international rock reference materials by inductively coupled plasma-mass spectrometry (ICP-MS) after pre-concentration by a nickel sulfide fire assay. It was possible to achieve determination limits for a 50 g sample that ranged from 1 pg g^-1 (Rh) to 23 pg g^-1 (Au). Compared to published certified and recommended values for rock reference materials, the trueness of the method was found to be good. However, in some cases we observed large deviations for all elements in the sub 10 ng g^-1 range within individual reference sample splits. Our results show that the PGE and Au are inhomogeneously distributed in the reference materials analysed here, where they are present in low concentrations, using 50 g test portions.     

New Progress on Certified Reference Materials for Platinum-Group Elements: IGGE GPt-8, GPt-9 and GPt-10

Three new certified reference materials (CRM), certified for the platinum-group elements (PGE), GPt-8, GPt-9 and GPt-10 were developed based on the previous CRMs IGGE GPt-1 to GPt-7. The PGE concentration of GPt-8 is about 1 ng g^-1. GPt-9 and GPt-10 are ore samples with PGE concentrations of more than 1 μg g^-1. A multi-laboratory collaborative analysis scheme was adopted in the certification procedure, in which nine highly-experienced institutes and laboratories participated. The samples were analysed for the six platinum-group elements by nickel sulfide mini fire assay, with Te coprecipitation, and were determined by ICP-MS. Osmium was determined by isotope dilution.     

FeSO4对铬污染土的稳定特性及风险评价试验研究

采用硫酸亚铁（FeSO4）对铬污染土进行稳定化处理。选用浸出试验、Cr(VI)残留值试验和形态提取试验,研究了粒径和有机质对铬污染土稳定特性的影响规律。试验结果表明,粒径和有机质对铬污染土稳定特性有较大影响。粒径的减小可显著降低稳定土中Cr(VI)和总Cr的浸出浓度及稳定土中Cr(VI)的含量;当污染土粒径小于2 mm时,Fe(II)/Cr(VI)摩尔比为3,稳定土中Cr(VI)和总Cr的浸出浓度分别为4.68、8.9 mg/L,均低于我国《危险废弃物鉴别标准 浸出毒性鉴别》（GB/T5085.3－2007）的限值。有机质添加量的增加可明显降低稳定土中Cr(VI)和总Cr的浸出浓度及Cr(VI)的含量。当Fe(II)/Cr(VI)摩尔比为3时,有机质的添加量为5%,稳定土中Cr(VI)的含量为28.3 mg/kg,低于我国《土壤环境质量标准》（GB15618－2008）中工业和商业用地限值（30 mg/kg）;当有机质的添加量为10%时,稳定土中Cr(VI)的含量为4.8 mg/kg,低于居住用地限值（5 mg/kg）。形态提取试验结果表明：粒径的减小可降低弱酸提取态的铬含量,增加可还原态的铬含量,而对可氧化态和残渣态的铬含量影响不大;有机质可促使弱酸提取态、可还原态的铬转化为可氧化态的铬,而残渣态的铬变化不大。稳定土中铬从活性态向较稳定态转化,是铬稳定土稳定特性和环境风险变化的根本原因。     

Simultaneous Determination of Total Carbon, Nitrogen, Hydrogen and Sulfur in Twenty-seven Geological Reference Materials by Elemental Analyser

The contents of total carbon, hydrogen, nitrogen and sulfur in twenty-seven geological reference materials, issued by five producer organisations (USGS, CCRMP, ANRT, NIST and GSJ) were determined using an automated simultaneous elemental analyser following combustion. In order to complete gasification of C and N in some geological materials, the combustion temperature needed to be greater than 1150 °C. The calibrator prepared from known amounts of reagent material was not adopted for more than 1.2% m/m of H. Unrealistically high values in certain materials supposed to contain less than 1000 μg g⁻¹ S may be due mainly to memory effects. The limit of detection was 50 μg g⁻¹ for C and N, 500 μg g⁻¹ for H and 1000 μg g⁻¹ for S. Although the blank value of C and N was always stable and less than one third of the detection limit, it had a slightly higher value for N and S. By repeating long-term analysis, high reproducibility for each of the four elements was verified. The method has been applied satisfactorily to a variety of geological reference materials, and recommended values for C, H and N for most of the reference materials studied have been tabulated.     

Determination of Platinum-Group Elements in Geological Reference Materials by High Resolution-ICP-MS after Nickel Sulfide Fire-Assay Collection and Te Co-Precipitation

Inductively coupled plasma-mass spectrometry (ICP-MS) after NiS fire assay-Te co-precipitation was employed in the determination of Ru, Rh, Pd, Os, Ir and Pt at ng g^-1 levels in six platinum-group element (PGE) geological reference materials. In general, the average of several results was in good agreement with the certified values taking into account respective uncertainties. High relative standard deviations were observed for the reference materials GPt-3 and GPt-4. Problems associated with the NiS fire assay procedure and PGE determination at the sub-10 ng g^-1 level are reviewed and discussed.     

Determination of Beryllium and Zirconium In 45 Geochemical Reference Samples By Inductively Coupled Plasma Emission Spectrometry

The beryllium and zirconium contents of 45 geochemical reference samples have been determined by inductively coupled plasma after fusion of the samples with lithium metaborate and dissolution of the melt in dilute nitric acid. The method described here is rapid and sample preparation straightforward. Good agreement is shown with previously published results for these two elements. A correction has to be made for an interference due to vanadium in determining the beryllium content, and there is a slight interference due to yttrium in the determination of zirconium. The detection limit for beryllium is about 0.2 μg g^-1 and for zirconium about 15 μg g^-1 in the sample.     

Sampling, Sample Preparation and ICP-MS Chemical Analysis of Lake Baikal Sponges

Procedures for sampling, sample preparation and ICP-MS analysis of endemic sponges from Lake Baikal have been developed. Sample decomposition was carried out using an open acid decomposition with ultrasound treatment. The distribution of nineteen elements (Mg, Al, P, Ca, Ti, Mn, Co, Ni, Cu, Rb, Sr, Y, Cd, Ba, La, Ce, Pb, Th and U) in different parts of a sponge's body (outer and inner layers and layers adjacent to the substratum) was studied. Detection limits were determined; these ranged from 0.013 to 4.12 μg g^-1 for trace elements and from 23 to 130 μg g^-1 for biogenic elements. The degree of elemental uptake by living substances is discussed with regard to the environment.     

Determination of Chlorine Contents in Geological Survey of Japan Reference Materials by Prompt Gamma Neutron Activation Analysis

We determined chlorine contents in nine GSJ (Geological Survey of Japan) reference materials (JB-1, 1a, 2, 3; JA-1, 2, 3; JR-1, 2) by prompt gamma neutron activation analysis, employing the standard addition method. Pressed powder disks of each reference material were used for neutron irradiation and gammaray measurement, after known quantities (25-200 μl) of sodium chloride solution were added. The influence of the nearby sodium peak overlap was checked, and fluctuations in the chlorine count rate were corrected using silicon as an internal standard. The slopes of calibration lines for seven reference materials (JB-1, 2, 3; JA-1, 2, 3; JR-2) and SiO₂ powders fall within 5% error, and their chlorine values were obtained from the intercepts. Chlorine contents in JB-1 a and JR-1 were also determined by using the calibration lines. Our chlorine values ranged from 26.1 to 934 μg g-¹, which agrees well with the previously reported values.     

Determination of Molybdenum in Fifty Three Geochemical Reference Materials by Flameless Atomic Absorption Spectrometry

The molybdenum (Mo) contents of fifty three geochemical reference materials issued by ANRT, GIT-IWG, NIST and GSJ, have been determined by atomic absorption spectrometry, using a graphite furnace atomiser, after extraction of Mo dithiol with isoamyl acetate. Detection limits for this method (0.01 μg g⁻¹) are ten times smaller than for most classical methods. The agreement between the present results and published data is satisfactory.     

Suppression of Matrix Effects in ICP-MS by High Power Operation of ICP: Application to Precise Determination of Rb, Sr, Y, Cs, Ba, REE, Pb, Th and U at ng g-1 Levels in Milligram Silicate Samples

We found that the suppression of signals for ⁸⁸Sr, ¹⁴⁰Ce and ²³⁸U in rock solution caused by rock matrix in ICP-MS (matrix effects) was reduced at high power operation (1.7 kW) of the ICP. To make the signal suppression by the matrix negligible, minimum dilution factors (DF) of the rock solution for Sr, Ce and U were 600, 400 and 113 at 1.1, 1.4 and 1.7 kW, respectively. Based on these findings, a rapid and precise determination method for Rb, Sr, Y, Cs, Ba, REE, Pb, Th and U using FI (flow injection)-ICP-MS was developed. The amount of the sample solution required for FI-ICP-MS was 0.2 ml, so that 1.8 mg sample was sufficient for analysis with a detection limit of several ng g^-1. Using this method, we determined the trace element concentrations in the USGS rock reference materials, DTS-1, PCC-1, BCR-1 and AGV-1, and the GSJ rock reference materials, JP-1, JB-1, -2, -3, JA-1, -2 and -3. The reproducibilities (RSD %) in replicate analyses (n=5) of BCR-1, AGV-1, JB-1, -2, -3, JA-1, -2, and -3 were < 6 %, and typically 2.5%. The difference between the average concentrations of this study for BCR-1 and those of the reference values were < 2%. Therefore, it was concluded that the method can give reliable data for trace elements in silicate rocks.