Mg Isotope Interlaboratory Comparison of Reference Materials from Earth‐Surface Low‐Temperature Environments

To enable quality control of measurement procedures for determinations of Mg isotope amount ratios, expressed as δ²⁶Mg and δ²⁵Mg values, in Earth‐surface studies, the δ²⁶Mg and δ²⁵Mg values of eight reference materials (RMs) were determined by interlaboratory comparison between five laboratories and considering published data, if available. These matrix RMs, including river water SLRS‐5, spring water NIST SRM 1640a, Dead Sea brine DSW‐1, dolomites JDo‐1 and BCS‐CRM 512, limestone BCS‐CRM 513, soil NIST SRM 2709a and vegetation NIST SRM 1515, are representative of a wide range of Earth‐surface materials from low‐temperature environments. The interlaboratory variability, 2s (twice the standard deviation), of all eight RMs ranges from 0.05 to 0.17‰ in δ²⁶Mg. Thus, it is suggested that all these materials are suitable for validation of δ²⁶Mg and δ²⁵Mg determinations in Earth‐surface geochemical studies.     

Nickel Isotope Variations in Terrestrial Silicate Rocks and Geological Reference Materials Measured by MC‐ICP‐MS

Although initial studies have demonstrated the applicability of Ni isotopes for cosmochemistry and as a potential biosignature, the Ni isotope composition of terrestrial igneous and sedimentary rocks, and ore deposits remains poorly known. Our contribution is fourfold: (a) to detail an analytical procedure for Ni isotope determination, (b) to determine the Ni isotope composition of various geological reference materials, (c) to assess the isotope composition of the Bulk Silicate Earth relative to the Ni isotope reference material NIST SRM 986 and (d) to report the range of mass‐dependent Ni isotope fractionations in magmatic rocks and ore deposits. After purification through a two‐stage chromatography procedure, Ni isotope ratios were measured by MC‐ICP‐MS and were corrected for instrumental mass bias using a double‐spike correction method. Measurement precision (two standard error of the mean) was between 0.02 and 0.04‰, and intermediate measurement precision for NIST SRM 986 was 0.05‰ (2s). Igneous‐ and mantle‐derived rocks displayed a restricted range of δ^60/58Ni values between ?0.13 and +0.16‰, suggesting an average BSE composition of +0.05‰. Manganese nodules (Nod A1; P1), shale (SDO‐1), coal (CLB‐1) and a metal‐contaminated soil (NIST SRM 2711) showed positive values ranging between +0.14 and +1.06‰, whereas komatiite‐hosted Ni‐rich sulfides varied from ?0.10 to ?1.03‰.     

The δ60/58Ni Values of Twenty‐Six Selected Geological Reference Materials

The high‐precision δ^60/58Ni values of twenty‐six geological reference materials, including igneous rocks, sedimentary rocks, stream sediments, soils and plants are reported. The δ^60/58Ni values of all samples were determined by double‐spike MC‐ICP‐MS (Nu Plasma III). Isotope standard solution (NIST SRM 986) and geological reference materials (BHVO‐2, BCR‐2, JP‐1, PCC‐1, etc.) were used to evaluate the measurement bias and intermediate precision over a period of six months. Our results show that the intermediate precision of Ni isotope determination was 0.05‰ (2s, n = 69) for spiked NIST SRM 986 and typically 0.06‰ for actual samples, and the δ^60/58Ni _{NIST SRM 986} values were in excellent agreement with previous studies. Eighteen high‐precision Ni isotope ratios of geological reference materials are first reported here, and their δ^60/58Ni values varied from ?0.27‰ to 0.52‰, with a mean of 0.13 ± 0.34‰ (2s, n = 18). Additionally, SGR‐1b (0.56 ± 0.04‰, 2s), GSS‐1 (?0.27 ± 0.06‰, 2s), GSS‐7 (?0.11 ± 0.01‰, 2s), GSD‐10 (0.46 ± 0.06‰, 2s) and GSB‐12 (0.52 ± 0.06‰, 2s) could potentially serve as candidate reference materials for Ni isotope fractionation and comparison of Ni isotopic compositions among different laboratories.     

High‐Precision Barium Isotope Measurements of Carbonates by MC‐ICP‐MS

This study presents a high‐precision method to measure barium (Ba) isotope compositions of international carbonate reference materials and natural carbonates. Barium was purified using chromatographic columns filled with cation exchange resin (AG50W‐X12, 200–400 mesh). Barium isotopes were measured by MC‐ICP‐MS, using a ¹³⁵Ba–¹³⁶Ba double‐spike to correct mass‐dependent fractionation during purification and instrumental measurement. The precision and accuracy were monitored by measuring Ba isotope compositions of the reference material JCp‐1 (coral) and a synthetic solution obtained by mixing NIST SRM 3104a with other matrix elements. The mean δ^137/134Ba values of JCp‐1 and the synthetic solution relative to NIST SRM 3104a were 0.21 ± 0.03‰ (2s, n = 16) and 0.02 ± 0.03‰ (2s, n = 6), respectively. Replicate measurements of NIST SRM 915b, COQ‐1, natural coral and stalagmite samples gave average δ^137/134Ba values of 0.10 ± 0.04‰ (2s, n = 18), 0.08 ± 0.04‰ (2s, n = 20), 0.27 ± 0.04‰ (2s, n = 16) and 0.04 ± 0.03‰ (2s, n = 20), respectively. Barium mass fractions and Ba isotopes of subsamples drilled from one stalagmite profile were also measured. Although Ba mass fractions varied significantly along the profile, Ba isotope signatures were homogeneous, indicating that Ba isotope compositions of stalagmites could be a potential tool (in addition to Ba mass fractions) to constrain the source of Ba in carbonate rocks and minerals.     

Barium Isotopic Compositions in Thirty‐Four Geological Reference Materials Analysed by MC‐ICP‐MS

Measurement of Ba isotope ratios of widely available reference materials is required for interlaboratory comparison of data. Here, we present new Ba isotope data for thirty‐four geological reference materials, including silicates, carbonates, river/marine sediments and soils. These reference materials (RMs) cover a wide range of compositions, with Ba mass fractions ranging from 6.4 to 1900 µg g^?1, SiO₂ from 0.62% to 90.36% m/m and MgO from 0.08% to 41.03% m/m. Accuracy and precision of our data were assessed by the analyses of duplicate samples and USGS rock RMs. Barium isotopic compositions for all RMs were in agreement with each other within uncertainty. The variation of δ^138/134Ba in these RMs was up to 0.7‰. The shale reference sample, affected by a high degree of chemical weathering, had the highest δ^138/134Ba (0.37 ± 0.03‰), while the stream sediment obtained from a tributary draining carbonate rocks was characterised by the lowest δ^138/134Ba (?0.30 ± 0.05‰). Geochemical RMs play a fundamental role in the high‐precision and accurate determination of Ba isotopic compositions for natural samples with similar matrices. Analyses of these RMs could provide universal comparability for Ba isotope data and enable assessment of accuracy for interlaboratory data.     

Cadmium stable isotope cosmochemistry

Cadmium stable isotope compositions are reported for a comprehensive suite of carbonaceous, ordinary, enstatite, and Rumuruti chondrites as well as achondrites and lunar samples (soils, breccias, pristine anorthosite). The Cd isotope analyses were performed by multiple collector ICP-MS with an external reproducibility of ±0.43‰ (2 sd) for δ^114/110Cd. None of the samples shows evidence of nucleosynthetic anomalies and cosmogenic isotope effects from neutron-capture by ¹¹³Cd were only observed for two lunar samples.The Cd stable isotope compositions of type 1, 2, and some type 3 carbonaceous chondrites, EH4 enstatite chondrites, eucrites, and the Earth are essentially identical at δ^114/110Cd ≈ 0.0 ± 0.4. This suggests that the portion of the solar nebula from which the inner solar system bodies accreted was homogeneous with respect to its Cd isotope composition. It also indicates that the primary volatile element depletion of the inner solar system did not involve partial kinetic Rayleigh evaporation or condensation. Furthermore no resolvable Cd isotope effects were generated during the accretion and initial differentiation of the planetary bodies.In contrast, the analyses reveal large Cd isotope effects for ordinary and some enstatite chondrites, which display δ^114/110Cd values between about −8 and +16. Smaller fractionations are observed for the Rumuruti and some type 3 to 5 carbonaceous chondrites. These Cd isotope variations are thought to reflect secondary depletion or redistribution of Cd, due to open system thermal metamorphism on the meteorite parent bodies.One CAI and chondrule separates from the Allende meteorite have unexpectedly high Cd concentrations and fractionated light Cd isotope compositions with δ^114/110Cd ≈ −1 to −4. These characteristics may have been established by the interaction of originally Cd-poor materials with a volatile-rich gas prior to the final accretion of the Allende parent body. The general Cd enrichment of the lunar soil and regolith mainly reflects early volcanic activity. However, decreasing Cd abundances in lunar soils correlate well with an enrichment of the heavy Cd isotopes. This relationship is best explained by suppressed Rayleigh fractionation in response to space weathering.     

Copper Isotopic Analysis in Geological and Biological Reference Materials by MC‐ICP‐MS

The characterisation of relative copper isotope amount ratios (δ⁶⁵Cu) helps constrain a variety of geochemical processes occurring in the geosphere, biosphere and hydrosphere. The accurate and precise determination of δ⁶⁵Cu in matrix reference materials is crucial in the effort to validate measurement methods. With the goal of expanding the number and variety of available geological and biological materials, we have characterised the δ⁶⁵Cu values of ten reference materials by MC‐ICP‐MS using C‐SSBIN model for mass bias correction. SGR‐1b (Green River shale), DOLT‐5 (dogfish liver), DORM‐4 (fish protein), TORT‐3 (lobster hepatopancreas), MESS‐4 (marine sediment) and PACS‐3 (marine sediment) have for the first time been characterised for δ⁶⁵Cu. Additionally, four reference materials (with published δ⁶⁵Cu values) have been characterised: BHVO‐1 (Hawaiian basalt), BIR‐1 (Icelandic basalt), W‐2a (diabase) and Seronorm? Trace Elements Serum L‐1 (human serum). The reference materials measured in this study possess complex and varied matrices with copper mass fractions ranging from 1.2 µg g^?1 to 497 µg g^?1 and δ⁶⁵Cu values ranging from ?0.20‰ to 0.52‰ with a mean expanded uncertainty of ± 0.07‰ (U, k = 2), covering much of the natural copper isotope variability observed in the environment.     

Automated Analyte Separation by Ion Chromatography Using a Cobot Applied to Geological Reference Materials for Li Isotope Composition

The demand for large and reliable data sets on isotopic composition has increased in geochemistry and environmental sciences over recent years. We present an automated ion chromatographic separation method using a robotic pipetting arm, termed ‘ChemCobOne’, to reduce sample separation time. Its performance was tested for lithium isotope separation in geological reference materials using a single‐step separation with HCl (0.2 mol l^?1) and a 2 ml resin volume. This refined lithium purification method does not forfeit precision, accuracy or purity compared with manual sample processing. In addition, a δ⁷Li value for NASS‐6 of 30.99 ± 0.50‰ (2s) (95% CI = 0.14‰, n = 44) was determined and the first δ⁷Li values for the granite rock reference material GS‐N (?0.57 ± 0.25‰ (2s), 95% CI = 0.15‰, n = 15), and for the soil reference material NIST SRM 2709a (?0.37 ± 0.67‰ (2s), 95% CI = 0.15‰, n = 63) are proposed.     

Mass‐Independent and Mass‐Dependent Ca Isotopic Compositions of Thirteen Geological Reference Materials Measured by Thermal Ionisation Mass Spectrometry

We report mass‐independent and mass‐dependent Ca isotopic compositions for thirteen geological reference materials, including carbonates (NIST SRM 915a and 915b), Atlantic seawater as well as ten rock reference materials ranging from peridotite to sandstone, using traditional ε and δ values relative to NIST SRM 915a, respectively. Isotope ratio determinations were conducted by independent unspiked and ⁴³Ca‐⁴⁸Ca double‐spiked measurements using a customised Triton Plus TIMS. The mean of twelve measurement results gave ε^40/44Ca values within ± 1.1, except for GSP‐2 that had ε^40/44Ca = 4.04 ± 0.15 (2SE). Significant radiogenic ⁴⁰Ca enrichment was evident in some high K/Ca samples. At an uncertainty level of ± 0.6, all reference materials had the same ε^43/44Ca and ε^48/44Ca values. We suggest the use of δ^44/42Ca to report mass‐dependent Ca isotopic compositions. The precision under intermediate measurement conditions for δ^44/42Ca over eight months in our laboratory was ± 0.03‰ (with n ≥ 8 repeat measurements). Measured igneous reference materials gave δ^44/42Ca values ranging from 0.27‰ to 0.54‰. Significant Ca isotope fractionation may occur during magmatic and metasomatism processes. Studied reference materials with higher (Dy_n/Yb_n) tend to have lower δ^44/42Ca, implying a potential role of garnet in producing magmas with low δ^44/42Ca. Sandstone GBW07106 had a δ^44/42Ca value of 0.22‰, lower than all igneous rocks studied so far.     

Cadmium and sulfur isotopic compositions of the Tianbaoshan Zn–Pb–Cd deposit,Sichuan Province,China

Although Zn–Pb deposits are one of the most important Cd reservoirs in the earth, few studies have focused on the Cd isotopic fractionation in Zn–Pb hydrothermal systems. This study investigates the causes and consequences of cadmium and sulfur isotope fractionation in a large hydrothermal system at the Tianbaoshan Zn–Pb–Cd deposit from the Sichuan–Yunnan–Guizhou (SYG) metallogenic province, SW China. Moderate variations in Cd and S isotope compositions have been measured in sphalerite cover a distance of about 78 m. Sphalerite has δ^114/110Cd values ranging from 0.01 to 0.57‰, and sulfides (sphalerite, galena and chalcopyrite) have δ³⁴S_CDT values ranging from 0.2 to 5.0‰. Although δ³⁴S_CDT and δ^114/110Cd values in sphalerites have no regular spatial variations, the δ³⁴S_CDT values in galena and calculated ore-forming fluid temperatures decreased from 2.1 to 0.2‰ and from about 290 to 130 °C, respectively, from the bottom to the top of the deposit. Heavy Cd isotopes are enriched in early precipitated sphalerite in contrast to previous studies. We suggest that Cd isotopic compositions in ore-forming fluids are heterogeneous, which result in heavy Cd isotope enrichment in early precipitated sphalerite. In comparison with other Zn–Pb deposits in the SYG area, the Tianbaoshan deposit has moderate Cd contents and small isotope fractionation, suggesting differences in origin to other Zn–Pb deposits in the SYG province.In the Tianbaoshan deposit, the calculated δ³⁴S∑_S-fluids value is 4.2‰, which is not only higher than the mantle-derived magmatic sulfur (0 ± 3‰), but also quite lower than those of Ediacaran marine sulfates (about 30 to 35‰). Thus, we suggest that reduced sulfur of ore-forming fluids in the deposit was mainly derived from the leaching of the basement, which contains large amount of volcanic or intrusive rocks. Based upon a combination of Cd and S isotopic systems, the Tianbaoshan deposit has different geochemical characteristics from typical Zn–Pb deposits (e.g., the Huize deposit) in SYG area, indicating the unique origin of this deposit.     

Off‐Mount Calibration and One New Potential Pyrrhotite Reference Material for Sulfur Isotope Measurement by Secondary Ion Mass Spectrometry

Sulfur isotope measurements in three sulfide (two pyrite and one pyrrhotite) samples on two epoxy mounts showed that the mount‐to‐mount variation of raw δ³⁴S values was negligible when secondary ion mass spectrometry (SIMS) analytical settings remained stable. In consequence, an off‐mount calibration procedure for SIMS sulfur isotope analysis was applied in this study. YP136 is a pyrrhotite sample collected from northern Finland. Examination of thin sections with a polarising microscope, backscattered electron image analyses and wavelength dispersive spectrometry mapping showed that the sample grains display no internal growth or other zoning. A total of 318 sulfur isotope (spot) measurements conducted on more than 100 randomly selected grains yielded highly consistent sulfur isotope ratios. The repeatability of all the analytical results of ³⁴S/³²S was 0.3‰ (2s, n = 318), which is the same as that of the well‐characterised pyrite reference materials PPP‐1 and UWPy‐1. Its δ³⁴S value determined by gas mass spectrometry was 1.5 ± 0.1‰ (2s, n = 11), which agrees with the SIMS data (1.5 ± 0.3‰, 2s) calibrated by pyrrhotite reference material Po‐10. Therefore, YP136 pyrrhotite is considered a candidate reference material for in situ sulfur isotope determination.     

SA01 – A Proposed Zircon Reference Material for Microbeam U‐Pb Age and Hf‐O Isotopic Determination

A new natural zircon reference material SA01 is introduced for U‐Pb geochronology as well as O and Hf isotope geochemistry by microbeam techniques. The zircon megacryst is homogeneous with respect to U‐Pb, O and Hf isotopes based on a large number of measurements by laser ablation‐inductively coupled plasma‐mass spectrometry (LA‐ICP‐MS) and secondary ion mass spectrometry (SIMS). Chemical abrasion isotope dilution thermal ionisation mass spectrometry (CA‐ID‐TIMS) U‐Pb isotopic analyses produced a mean ²⁰⁶Pb/²³⁸U age of 535.08 ± 0.32 Ma (2s, n = 10). Results of SIMS and LA‐ICP‐MS analyses on individual shards are consistent with the TIMS ages within uncertainty. The δ¹⁸O value determined by laser fluorination is 6.16 ± 0.26‰ (2s, n = 14), and the mean ¹⁷⁶Hf/¹⁷⁷Hf ratio determined by solution MC‐ICP‐MS is 0.282293 ± 0.000007 (2s, n = 30), which are in good agreement with the statistical mean of microbeam analyses. The megacryst is characterised by significant localised variations in Th/U ratio (0.328–4.269) and Li isotopic ratio (?5.5 to +7.9‰); the latter makes it unsuitable as a lithium isotope reference material.     

Development and Re‐Evaluation of Tourmaline Reference Materials for In Situ Measurement of Boron δ Values by Secondary Ion Mass Spectrometry

Six tourmaline samples were investigated as potential reference materials (RMs) for boron isotope measurement by secondary ion mass spectrometry (SIMS). The tourmaline samples are chemically homogeneous and cover a compositional range of tourmaline supergroup minerals (primarily Fe, Mg and Li end‐members). Additionally, they have homogeneous boron delta values with intermediate precision values during SIMS analyses of less than 0.6‰ (2s). These samples were compared with four established tourmaline RMs, that is, schorl IAEA‐B‐4 and three Harvard tourmalines (schorl HS#112566, dravite HS#108796 and elbaite HS#98144). They were re‐evaluated for their major element and boron delta values using the same measurement procedure as the new tourmaline samples investigated. A discrepancy of about 1.5‰ in δ¹¹B was found between the previously published reference values for established RMs and the values determined in this study. Significant instrumental mass fractionation (IMF) of up to 8‰ in δ¹¹B was observed for schorl–dravite–elbaite solid solutions during SIMS analysis. Using the new reference values determined in this study, the IMF of the ten tourmaline samples can be modelled by a linear combination of the chemical parameters FeO + MnO, SiO₂ and F. The new tourmaline RMs, together with the four established RMs, extend the boron isotope analysis of tourmaline towards the Mg‐ and Al‐rich compositional range. Consequently, the in situ boron isotope ratio of many natural tourmalines can now be determined with an uncertainty of less than 0.8‰ (2s).     

Accurate and Precise Silicon Isotope Analysis of Sulfur‐ and Iron‐Rich Samples by MC‐ICP‐MS

Silicon isotope determination of sulfur‐rich samples by MC‐ICP‐MS can be challenging because cation‐exchange chromatography used for Si purification does not efficiently remove anionic sulfur species. Results for pure Si standard solutions with addition of sulfate showed shifts of up to +1.04 ± 0.10‰ (2s) in δ³⁰Si. Doping of both standard solutions and samples with S to a fixed S/Si ratio can eliminate the relative change in instrumental mass fractionation due to variable S/Si in samples and also boosts the relative sensitivity of Si by up to 66%. Moreover, Fe hydroxide precipitation during sample processing adsorbs Si resulting in isotopic fractionations. Tests using Fe‐rich samples showed that this could be a major factor for observed shifts in δ³⁰Si. Acidification of the sample and standard solutions to a pH < 1 aggressively dissolved any Fe hydroxide precipitates, even in relatively Fe‐rich samples such as chondrite meteorites. The pH values of the sample solutions were subsequently adjusted to a range of 2–3 by adding ultra‐pure NaOH solutions. The combination of sulfur doping and the pH adjustment protocol ensured a full recovery of Si and proved to be an efficient and reliable method for Si isotope determination of S‐ and Fe‐rich materials.     

Zinc Isotopic Compositions of NIST SRM 683 and Whole‐Rock Reference Materials

In this study the homogeneity of the zinc isotopic composition in the NIST SRM 683 reference material was examined by measuring the Zn isotopic signature in microdrilled sample powders from two metal nuggets. Zinc was purified using AG MP‐1M resin and then measured by MC‐ICP‐MS. Instrumental mass bias was corrected using the “sample‐standard bracketing” method and empirical external normalisation with Cu doping. After evaluating the potential effects of varying acid mass fractions and different matrices, high‐precision Zn isotope data were obtained with an intermediate measurement precision better than ± 0.05‰ (δ⁶⁶Zn, 2s) over a period of 5 months. The δ⁶⁶Zn_JMC‐Lyon mean values of eighty‐four and fourteen drilled powders from two nuggets were 0.11 ± 0.02‰ and 0.12 ± 0.02‰, respectively, indicating that NIST SRM 683 is a good isotopic reference material with homogeneous Zn isotopes. The Zn isotopic compositions of seventeen rock reference materials were also determined, and their δ⁶⁶Zn values were in agreement with most previously published data within 2s. The δ⁶⁶Zn values of most of the rock reference materials analysed were in the range 0.22–0.36‰, except for GSP‐2 (1.07 ± 0.06‰, n = 12), NOD‐A‐1 (0.96 ± 0.03‰, n = 6) and NOD‐P‐1 (0.78 ± 0.03‰, n = 6). These comprehensive data should serve as reference values for quality assurance and interlaboratory calibration exercises.     

Precise Determination of Silicon Isotopes in Silicate Rock Reference Materials by MC‐ICP‐MS

A HF‐free sample preparation method was used to purify silicon in twelve geological RMs. Silicon isotope compositions were determined using a Neptune instrument multi‐collector‐ICP‐MS in high‐resolution mode, which allowed separation of the silicon isotope plateaus from their interferences. A 1 μg g^‐1 Mg spike was added to each sample and standard solution for online mass bias drift correction. δ³⁰Si and δ²⁹Si values are expressed in per mil (‰), relative to the NIST SRM 8546 (NBS‐28) international isotopic RM. The total variation of δ³⁰Si in the geological reference samples analysed in this study ranged from ‐0.13‰ to ‐0.29‰. Comparison with δ²⁹Si values shows that these isotopic fractionations were mass dependent. IRMM‐17 yielded a δ³⁰Si value of ‐1.41 ± 0.07‰ (2s, n = 12) in agreement with previous data. The long‐term reproducibility for natural samples obtained on BHVO‐2 yielded δ³⁰Si = ‐0.27 ± 0.08‰ (2s, n = 42) on a 12 month time scale. An in‐house Si reference sample was produced to check for the long‐term reproducibility of a mono‐elemental sample solution; this yielded a comparable uncertainty of ± 0.07‰ (2s, n = 24) over 5 months.     

Tracing sources of pollution in soils from the Jinding Pb–Zn mining district in China using cadmium and lead isotopes

Systematic variations in the Cd and Pb isotope ratios in polluted topsoils surrounding the Jinding Pb–Zn mine in China were measured so that the sources of the metals could be traced. The average δ^114/110Cd value and ²⁰⁶Pb/²⁰⁷Pb isotope ratio in background soils from the region were +0.41‰ and 1.1902, respectively, whereas the contaminated soil samples had different values, with the δ^114/110Cd values varying between −0.59‰ and +0.33‰ and the ²⁰⁶Pb/²⁰⁷Pb isotope ratios varying between 1.1764 and 1.1896. We also measured the Cd and Pb isotopic compositions in oxide ores, sulfide ores, and slags, and found that binary mixing between ores and background soils could explain almost all of the variations in the Cd and Pb isotope ratios in the contaminated soils. This suggests that Cd and Pb pollution in the soils was mainly caused by the deposition of dust emitted during anthropogenic activities (mining and refining). The Pb and Cd isotope ratios clearly showed that contamination in soils in the northeastern part of the area was caused by surface mines and zinc smelters and their slagheaps, while contamination in soils in the southwestern part of the area also came from tailing ponds and underground mines. The main area of soil polluted by dust from Pb–Zn mining processes roughly extended for up to 5 km from the mine itself.     

High‐Precision Measurement of Stable Cr Isotopes in Geological Reference Materials by a Double‐Spike TIMS Method

Chromium (Cr) isotopes have been widely used in various fields of Earth and planetary sciences. However, high‐precision measurements of Cr stable isotope ratios are still challenged by difficulties in purifying Cr and organic matter interference from resin using double‐spike thermal ionisation mass spectrometry. In this study, an improved and easily operated two‐column chemical separation procedure using AG50W‐X12 (200–400 mesh) resin is introduced. This resin has a higher cross‐linking density than AG50W‐X8, and this higher density generates better separation efficiency and higher saturation. Organic matter from the resin is a common cause of inhibition of the emission of Cr during analysis by TIMS. Here, perchloric and nitric acids were utilised to eliminate organic matter interference. The Cr isotope ratios of samples with lower Cr contents could be measured precisely by TIMS. The long‐term intermediate measurement precision of δ^53/52Cr_{NIST SRM 979} for BHVO‐2 is better than ± 0.031‰ (2s) over one year. Replicated digestions and measurements of geological reference materials (OKUM, MUH‐1, JP‐1, BHVO‐1, BHVO‐2, AGV‐2 and GSP‐2) yield δ^53/52Cr_{NIST SRM 979} results ranging from ?0.129‰ to ?0.032‰. The Cr isotope ratios of geological reference materials are consistent with the δ^53/52Cr_{NIST SRM 979} values reported by previous studies, and the measurement uncertainty (± 0.031‰, 2s) is significantly improved.     

Precise determination of cadmium isotope fractionation in seawater by double spike MC-ICPMS

A new technique has been developed for the accurate and precise determination of the stable Cd isotope composition of seawater. The method utilizes a ¹¹⁰Cd-¹¹¹Cd double spike, and it involves separation of Cd from seawater by column chromatography and isotopic analyses by multiple collector inductively coupled plasma mass spectrometry. As a by-product, it also generates precise Cd concentration data. Repeated analyses of three pure Cd reference materials and three seawater samples yielded reproducibilities of about ±1.0 to ±1.6 ε^114/110Cd (2 SD), based on measurements that each consumed about ∼8 ng of natural Cd (ε^114/110Cd is the deviation of the ¹¹⁴Cd/¹¹⁰Cd isotope ratio of a sample from the standard in parts per 10,000). This demonstrates that the new double spike technique is superior to published methods of Cd isotope analyses, with regard to the acquisition of precise data for samples of limited size. Additional experiments showed that as little as 1-5 ng of seawater Cd could be analyzed with a precision of about ±2 to ±6 ε^114/110Cd (2 SD). The accuracy of the seawater isotope data was ascertained by experiments in which a Cd-free seawater matrix was doped with small quantities of isotopically well-characterized Cd. Repeated mass scans that were carried out on purified Cd fractions of several samples furthermore demonstrated the absence of significant spectral interferences. The isotope data that were acquired for the three seawater samples reveal, for the first time, small but resolvable Cd isotope fractionations in the marine environment. Cadmium-rich intermediate water from the North Pacific was found to have an isotope composition of ε^114/110Cd = 3.2 ± 1.0. In contrast, Cd-depleted seawater from the upper water column of the Atlantic and Arctic Oceans displayed isotope compositions of ε^114/110Cd = 6.4 ± 1.1 and 6.6 ± 1.6, respectively. These observations are in accord with the interpretation that the isotope effects are due to the biological fractionation that occurs during the uptake of dissolved seawater Cd by phytoplankton.     

Sub‐Permil Interlaboratory Consistency for Solution‐Based Boron Isotope Analyses on Marine Carbonates

Boron isotopes in marine carbonates are increasingly used to reconstruct seawater pH and atmospheric pCO₂ through Earth’s history. While isotope ratio measurements from individual laboratories are often of high quality, it is important that records generated in different laboratories can equally be compared. Within this Boron Isotope Intercomparison Project (BIIP), we characterised the boron isotopic composition (commonly expressed in δ¹¹B) of two marine carbonates: Geological Survey of Japan carbonate reference materials JCp‐1 (coral Porites) and JCt‐1 (giant clam Tridacna gigas). Our study has three foci: (a) to assess the extent to which oxidative pre‐treatment, aimed at removing organic material from carbonate, can influence the resulting δ¹¹B; (b) to determine to what degree the chosen analytical approach may affect the resultant δ¹¹B; and (c) to provide well‐constrained consensus δ¹¹B values for JCp‐1 and JCt‐1. The resultant robust mean and associated robust standard deviation (s*) for un‐oxidised JCp‐1 is 24.36 ± 0.45‰ (2s*), compared with 24.25 ± 0.22‰ (2s*) for the same oxidised material. For un‐oxidised JCt‐1, respective compositions are 16.39 ± 0.60‰ (2s*; un‐oxidised) and 16.24 ± 0.38‰ (2s*; oxidised). The consistency between laboratories is generally better if carbonate powders were oxidatively cleaned prior to purification and measurement.