不规则波作用下垂直挡板式透空堤透浪系数试验研究

垂直挡板式透空堤作为一种新型的透空式防波堤结构,通过将挡浪板垂直设置于波能最集中的水体表层来消减波浪,透浪系数是其最关键的指标。通过物理模型试验,分析不规则波作用下入射波高、波周期、挡板相对入水深度、相对堤宽、相对挡板超高、相对面板超高等因素对垂直挡板式透空堤透浪系数的影响规律,并在Wiegel公式的基础上拟合了垂直挡板式透空堤透浪系数的计算公式。可作为今后类似透空式防波堤结构透浪系数的近似估算,具有一定的参考价值。     

双挡板透空堤透浪与反射系数实验研究

设有挡浪板结构的透空式防波堤适用于水深较大的海域,且具有较好的消浪效果。采用物理模型试验,探究具有双侧挡浪板结构的透空式防波堤透浪系数与反射系数的影响因素与规律,研究包括外侧与内侧挡浪板入水深度,水平板板宽,结构上部挡浪墙的高度与位置,水平板超高与波浪要素等因素。通过比较各家透浪系数的理论计算公式与实验结果,进行透浪系数的计算方法研究,给出修正Wiegel公式拟合双侧挡浪板透空式防波堤的透浪系数计算公式,供工程设计参考与进一步研究。     

新型直立式透空堤消浪性能数值研究

为使防波堤同时具有良好的掩护效果和水体交换能力,提出了两种带有透浪通道的新型直立式防波堤。基于Fluent求解器建立了三维数值波浪水槽,通过与试验结果对比,验证了该数值水槽求解波浪与透空堤作用具有较高的精度。对两种防波堤在规则波作用下的透浪特性进行了研究,结果表明:透射系数K_t与透空率呈正线性相关,且可通过调整透浪通道间距,使相同透空率下K_t降低20%～30%。对同一结构,K_t随相对波长的增大而显著增大,但受相对波高的影响较小。在透空率大于0.16后,异型沉箱防波堤的消浪性能明显优于错位沉箱。基于数值计算结果,给出了以上两种透空堤波浪透射系数的经验公式。     

高桩挡板透空式防波堤消浪性能数值研究

以RANS方程为控制方程,基于有限体积法,在动量方程中添加源项,建立了具有造波‐消波功能的数值波浪水槽。利用建立的源项造波数值波浪水槽,模拟了高桩挡板透空式防波堤在规则波作用下的消浪效果,完整地再现了堤前堤后的流态,分析了挡板相对入水深度对透浪系数的影响。在与试验值及拉帕公式对比后发现,数模计算结果与试验值较接近,拉帕公式偏大。研究了堤顶相对宽度、相对水深、相对波高对透浪系数的影响并提出修正公式,修正公式与计算值和试验值吻合较好。     

倾斜挡浪板式桩基透空型防波堤的消浪性能研究

本文提出了一种倾斜挡浪板式桩基透空型防波堤,通过物理模型试验对规则波作用下防波堤的消浪性能进行了研究。试验中观测了桩基透空型防波堤迎浪侧和背浪侧波面的变化过程,探讨了不同入射波浪条件下防波堤挡浪板的开孔率ε和布置形式B对其消浪性能的影响,分析了防波堤的反射系数K_r、透射系数K_t以及波能耗散系数K_d随着相对波高H/D和相对堤宽W/L的变化关系,并从波浪能量分布的角度分析此种防波堤的消浪机理。研究结果表明,单层挡浪板的开孔率自30%降低至10%,平均透射系数可减小约24.3%,平均耗散系数可增长约12.8%;双层挡浪板防波堤的反射系数取决于前排挡浪板的开孔率,透射系数取决于挡浪板组合中的最小开孔率。     

圆弧板透空式防波堤消波性能试验研究

提出了一种由多层圆弧板组成的新型透空式防波堤结构,并对其在二维规则波浪作用下的消波性能进行了物理模型试验研究。在不同入射波高条件下,对圆弧板和水平板透空结构的消波性能进行了比较分析,探讨了圆弧板间距和层数对圆弧板透空式结构消波性能的影响。研究结果表明,圆弧板透空式结构的消波效果优于水平板式透空结构,在相对宽度为0.2时,可以使透射系数达0.5以下。随着圆弧板间距从0.15 m减小到0.05 m时,消波效果逐步提升,而圆弧板的层数对结构的消波性能也有一定影响。     

透空管式防波堤透射系数及反射系数的试验研究

对透空管式防波堤的消浪性能进行了研究,通过进行物理模型试验,深入探讨了管道防波堤的堤顶宽度、斜率、波陡对防波堤消浪效果的影响,得出了该结构的反射系数及透射系数与各影响参数间的关系。研究结果表明,堤顶宽度为1.2Hm,斜率为1∶1.5的模型消浪效果较好。     

T型防波堤与波浪相互作用数值研究

针对T型透空式防波堤,通过浪高仪采集防波堤前后不同位置波面变化曲线,使用声学多普勒流速仪(NDV)测量不同位置流速随时间的变化,并分析了其相位平均流速的分布。基于VOF法的二维波浪数值水槽,对规则波作用下T型防波堤附近的动力特性进行了计算,水槽模型试验结果和数值模拟结果对比表明,数值计算结果与实验值吻合较好。采用该模型进一步对T型防波堤附近波浪场、流线、紊动动能、紊动动能耗散率变化以及不同尺寸的防波堤消浪效果进行模拟计算,重点分析了入射波高、防波堤入水深度和防波堤宽度变化的影响。     

弧板式透空堤消浪性能影响因素数值研究

弧板式透空堤是由弧型板组成的新型防波堤结构。为探讨其透射系数的影响因素,利用Fluent软件基于N-S方程构建了波浪与板式透空堤相互作用的数值模型,讨论了相对潜深、入射波周期、相对波高、相对板宽和结构型式对透射系数的影响。结果表明:弧板式透空堤的透射系数随着相对波高和入射波周期的增大而增大,在静水面附近透射系数最小,尤以静水面和略高于静水面时的消浪效果最佳;在相同波浪要素条件下,静水面及其上0.02 m和0.04 m位置处,弧板式透空堤的消浪效果明显优于平板式透空堤。     

双浮箱式浮式防波堤消浪性能试验研究

浮式防波堤在港口海岸工程、近海工程、海洋工程和水产养殖等诸多领域有广阔的应用前景。与单浮箱式浮式防波堤相比,多浮箱式浮式防波堤可提高其消浪性能。对双浮箱式浮式防波堤进行了二维波浪物理模型试验,分析了浮箱宽度、前后浮箱连接方式、前后浮箱间距以及浮箱入水深度等因素对浮式防波堤消浪性能的影响。研究结果表明:对于单浮箱式浮式防波堤,试验范围内浮箱宽度增大一倍后消浪效果改善并不相对明显;前后浮箱刚性连接的双浮箱式浮堤的波浪透射系数均小于前后浮箱自由的双浮箱式浮堤和相同浮箱宽度的单浮箱式浮堤,浮堤消浪性能提高;由于前后浮箱相对间距太大时前后浮箱的相互作用减弱,浮堤的波浪反射系数变小,而不同前后浮箱相对间距的波能损耗系数整体上差别较小,双浮箱式浮堤的波浪透射系数整体上随着前后浮箱相对间距D/2B的增大先减小然后变大,在相对间距D/2B为1.0~1.5时双浮箱式浮堤的波浪透射系数相比最小;不同波高和波浪周期下,浮堤的波浪透射系数均随着浮箱相对入水深度的增大而减小。     

Experimental Research on Wave Transmission over Submerged Rubble Mound Breakwaters

This paper discusses some previous, and presents some new experimental results on wave transmission over submerged breakwaters. The objective of this study is to evaluate wave transmission coefficient and develop a two-dimensional （2D） model as an improvement to the existing wave transmission coefficient models. Factors which affect wave transmission over stbmerged breakwaters are discussed through a series of laboratory experiments. Basic recommendations for evaluation and design of submerged rubble-monud breakwaters are presented. From the test results, a calculation formula of wave transmission coefficient is proposed.     

A wave-flume study of scour at a pile breakwater: Solitary waves

Understanding the sediment transport and the resulting scour around coastal structures such as pile breakwaters under local extreme wave conditions is important for the foundation safety of various coastal structures. This study reports a wave-flume experiment investigating the scour induced by solitary waves at a pile breakwater, which consists of a row of closely spaced large piles. A wave blacking gate with a simple operation procedure in the experiment was designed to eliminate possible multiple reflections of the solitary wave inside the flume. An underwater laser scanner and a point probe were used in combination to provide high-resolution data of the bed profile around the pile breakwater. Effects of incident wave height and local water depth on the maximum scour depth, the maximum deposition height and the total scour and deposition volumes were examined. An existing empirical formula describing the evolution of the scour at a single pile in current or waves was extended to describe the scour at the pile breakwater under the action of multiple solitary waves, and new empirical coefficients were obtained by fitting the formula to the new experimental data to estimate the equilibrium scour depth. It appears that the maximum scour depth and the total scour volume are two reliable quantities for validation of numerical models developed for the scour around pile breakwaters under highly nonlinear wave conditions.     

Interaction Between Waves and A Comb-Type Breakwater

The characteristics of wave transmission, reflection and energy dissipation of comb-type caisson breakwaters are studied through laboratory physical model tests. Regular and irregular waves, with a wide range of wave heights and periods and a constant water depth, are considered. Different dimensions of each portion of the comb-type caisson breakwater are tested. Empirical formulae for calculating the reduction coefficient k, which is the ratio of horizontal wave force on unit length of the comb-type breakwater to that on unit length of the vertical wall breakwater, and for calculating the reflection coefficient of waves k, are obtained from the measurements. The comb-type caisson breakwater has been found to be very efficient in dissipating incident wave energy and in reducing wave reflection, and has already been used for the construction of an island breakwater in the Dayao Bay of Dalian Port, Liaoning Province, China. Compared with the cost of a common caisson breakwater, about 24. 5% of the investm     

Experimental Research on Wave Transmission over Submerged Rubble-Mound Breakwaters

This paper discusses some previous, and presents some new experimental results on wave transmission oversubmerged breakwaters. The objective of this study is to evaluate wave transmission coefficient and develop two-dimensional (2D) model as an improvement to the existing wave transmission coefficient models. Factors which affect wave transmission over submerged breakwaters are discussed through series of laboratory experiments. Basic recommendations for evaluation and design of submerged rubble-monud breakwaters are presented.From the test results, calculation formula of wave transmission coefficient is proposed.     

Modelling of Random Waves over Submerged Breakwaters and Its Application to Reflection Estimation

1.IntroductionGreat efforts have been devoted to the protection of coastal areas over many years by erectingdikes,seawalls,groin systems,and detached breakwaters.The sea walls,jetties,detached breakwa-ters,etc.are traditionally adopted as absorbingfacilit…     

Long wave reflection from submerged trapezoidal breakwaters

This study addresses the reflection and transmission of long waves from a trapezoidal breakwater and a series of trapezoidal breakwaters, using the matching method. A systematic shape transfer is derived to determine wave reflection and transmission. The peak Bragg reflection of long waves from a series of trapezoidal breakwaters is shifted toward low frequency. In spite of the spacing between any pair of breakwaters, the top plane width and the arrangement of the series of breakwaters are found to be the two major parameters in designing multiply composite Bragg breakwaters.     

Performance of solid and perforated U-type breakwaters under regular and irregular waves

An experimental investigation of U-type breakwaters was carried out in a laboratory channel. Both regular and irregular waves were used during testing. Two types of breakwaters such as solid and perforated were studied to analyse the porosity effect of structures. In order to investigate performance of these breakwaters for different immersion depths, four depths of immersions of the solid and perforated breakwaters were selected. Different wave groups were generated over these breakwaters, and the transmission, reflection and energy dissipation characteristics of each breakwater were determined. Three coefficients such as transmission, reflection and energy dissipation coefficients, which were named as C_t, C_r, and C_l, respectively, were used during the evaluation of the test results. The most important parameters governing performance of these breakwaters were determined by using earlier investigations and experimental results. These parameters were expressed as a dimensionless group by using π theory. Based on the test results, empirical expressions were formulated to describe the C_t, C_r, and C_l for different immersion depths of solid and perforated breakwaters under regular and irregular waves.     

近破波作用下沉箱式防波堤运动特性的模型实验研究

对近破波作用下沉箱式防波堤的运动特性进行了模型实验研究。实验中测量了沉箱模型与基床的摩擦系数、基床刚度和阻尼系数;不同水位情况下作用于沉箱模型上的近破波波压力时程;近破波作用下沉箱模型的位移和转角响应时程等,并与数学模型计算结果进行了比较分析。实验结果表明,若沉箱的滑移力大于沉箱与基床间的摩擦力,在连续波浪作用下,沉箱将连续出现间歇式滑移运动,数学模型可较好地模拟这一运动过程。     

Wave Scattering by Double Slotted Barriers in A Steady Current： Experiments

The adoption of slotted breakwaters can be an ideal option in the protection of very large near-shore floating struc-trees that may extend offshore to a considerable water depth. In this paper, we experimently investigated the behaviour of wave transmission and reflection coefficients of double slotted barriers in the presence of a steady opposing current. The experimental results show that opposing currents have only minor effects on wave reflection, but can significantly reduce the wave transmission through double slotted barriers. The experimental results suggest that coastal currents should be taken into consideration for an economical design of slotted breakwaters.