Video‐based gravel transport measurements with a flume mounted light table

The study of bedload transport processes is constrained by an inability to monitor the mass, volume and grain size distribution of sediment in transport at high temporal frequencies. Building upon a previously published design, we have integrated a high‐resolution (1392 × 1024 pixels) video camera with a light table to continuously capture images of 2–181 mm material exiting a flume. The images are continuously recorded at a rate of 15 to 20 frames per second and are post‐processed using LabView^(?) software, yielding continuous grain‐size‐specific transport information on a per second basis. The video capture rate is sufficient to record multiple images of each grain leaving the flume so that particle velocities can be measured automatically. No manual image processing is required. After calibration the method is accurate and precise for sediment in the 2 mm through to 45 mm grain size classes compared with other means of measuring bedload. Based on a set of validation samples, no statistically significant difference existed between the D₁₀, D₁₆, D₂₅, D₅₀, D₇₅, D₈₄, D₉₀ and D₉₅ determined by sieving captured samples and the D_i values determined with the system. On average the system overpredicted transport by 4 per cent (n = 206, SD = 42%). This error can be corrected easily by simply weighing the mass of sediment that leaves the flume. The technology is relatively inexpensive and provides high‐resolution data on coarse sediment transport out of a flume. Copyright © 2008 John Wiley & Sons, Ltd.     

Coarse sediment transport in mountain streams in Colorado and Wyoming,USA

Since the early 1990s, US Forest Service researchers have made thousands of bedload measurements in steep, coarse‐grained channels in Colorado and Wyoming, USA. In this paper we use data from 19 of those sites to characterize patterns and rates of coarse sediment transport for a range of channel types and sizes, including step–pool, plane‐bed, pool–riffle, and near‐braided channels. This effort builds upon previous work where we applied a piecewise regression model to (1) relate flow to rates of bedload transport and (2) define phases of transport in coarse‐grained channels. Earlier, the model was tested using bedload data from eight sites on the Fraser Experimental Forest near Fraser, Colorado. The analysis showed good application to those data and to data from four supplementary channels to which the procedure was applied. The earlier results were, however, derived from data collected at sites that, for the most part, have quite similar geology and runoff regimes. In this paper we evaluate further the application of piecewise regression to data from channels with a wider range of geomorphic conditions. The results corroborate with those from the earlier work in that there is a relatively narrow range of discharges at which a substantial change in the nature of bedload transport occurs. The transition from primarily low rates of sand transport (phase I) to higher rates of sand and coarse gravel transport (phase II) occurs, on average, at about 80 per cent of the bankfull (1·5‐year return interval) discharge. A comparison of grain sizes moved during the two phases showed that coarse gravel is rarely trapped in the samplers during phase I transport. Moreover, the movement and capture of the D₁₆ to D₂₅ grain size of the bed surface seems to correspond with the onset of phase II transport, particularly in systems with largely static channel surfaces. However, while there were many similarities in observed patterns of bedload transport at the 19 studied sites, each had its own ‘bedload signal’ in that the rate and size of materials transported largely reflected the nature of flow and sediment particular to that system. Published in 2005 by John Wiley & Sons, Ltd.     

The causes of bedload pulses in a gravel channel: the implications of bedload grain‐size distributions

Unsteady bedload transport was measured in two c. 5 m wide anabranches of a gravel‐bed braided stream draining the Haut Glacier d'Arolla, Switzerland, during the 1998 and 1999 melt seasons. Bedload was directly sampled using 152 mm square Helley–Smith type samplers deployed from a portable measuring bridge, and independent transport rate estimates for the coarser size fractions were obtained from the dispersion of magnetically tagged tracer pebbles. Bedload transport time series show pulsing behaviour under both marginal (1998) and partial (1999) transport regimes. There are generally weak correlations between transport rates and shear stresses determined from velocity data recorded at the measuring bridge. Characteristic parameters of the bedload grain‐size distributions (D₅₀, D₈₄) are weakly correlated with transport rates. Analysis of full bedload grain‐size distributions reveals greater structure, with a tendency for transport to become less size selective at higher transport rates. The bedload time series show autoregressive behaviour but are dif?cult to distinguish by this method. State–space plots, and associated measures of time‐series separation, reveal the structure of the time series more clearly. The measured pulses have distinctly different time‐series characteristics from those modelled using a one‐dimensional sediment routing model in which bed shear stress and grain size are varied randomly. These results suggest a mechanism of pulse generation based on irregular low‐amplitude bedforms, that may be generated in‐channel or may represent the advection of material supplied by bank erosion events. Copyright © 2003 John Wiley & Sons, Ltd.     

Quantifying the Morphological Print of Bedload Transport

Bedload and river morphology interact in a strong feedback manner. Bedload conditions the development of river morphology along different space and time scales; however, by concentrating the flow in preferential paths, a given morphology controls bedload for a given discharge. As bedload is a non‐linear response of shear stress, local morphology is likely to have a strong impact on bedload prediction when the shear stress is averaged over the section, as is usually done. This was investigated by comparing bedload measured in different bed morphologies (step‐pool, plane bed, riffle‐pool, braiding, and sand beds), with bedload measured in narrow flumes in the absence of any bed form, used here as a reference. The initial methodology consisted of fitting a bedload equation to the flume data. Secondly, the morphological signature of each river was studied as the distance to this referent equation. It was concluded that each morphology affects bedload in a different way. For a given average grain shear stress, the larger the river, the larger the deviation from the flume transport. Narrow streams are those morphologies that behave more like flumes; this is particularly true with flat beds, whereas results deviate from flumes to a greater extent in step‐pools. The riffle‐pool's morphology impacts bedload at different levels depending on the degree of bar development, considered here through the ratio D₈₄/D₅₀ which is used as a proxy for the local bed patchiness and morphology. In braiding rivers morphological effects are important but difficult to assess because width is dependent on transport rate. Bed morphology was found to have negligible effects in sand bed rivers where the Shields stress is usually sufficiently high to minimize the non‐linearity effects when hydraulics is averaged over the section. Copyright © 2015 John Wiley & Sons, Ltd.     

Channel flow competence and sediment transport in upland streams in southeast Australia

Bedload transport data from planebed and step‐pool reach types are used to determine grain size transport thresholds for selected upland streams in southeast Australia. Morphological differences between the reach types allow the effects of frictional losses from bedforms, microtopography and bed packing to be incorporated into the dimensionless critical shear stress value. Local sediment transport data are also included in a regime model and applied to mountain streams, to investigate whether empirical data improve the delineation of reach types on the basis of dimensionless discharge per unit width (q*) and dimensionless bedload transport (q_b*). Instrumented planebed and step‐pool sites are not competent to transport surface median grains (D_50s) at bankfull discharge (Q_bf). Application of a locally parametrized entrainment equation to the full range of reach types in the study area indicates that the majority of cascades, cascade‐pools, step‐pools and planebeds are also not competent at Q_bf and require a 10 year recurrence interval flood to mobilize their D_50s. Consequently, the hydraulic parameters of the regime diagram, which assume equilibrium conditions at bankfull, are ill suited to these streams and provide a poor basis of channel delineation. Modifying the diagram to better reflect the dominant transported bedload size (equivalent to the D₁₆ of surface sediment) made only slight improvements to reach delineation and had greatest effect on the morphologies with smaller surface grain sizes such as forced pool‐riffles and planebeds. Likewise, the Corey shape factor was incorporated into the regime diagram as an objective method for adjusting a base dimensionless critical shear stress (τ*_c50b) to account for lithologically controlled grain shape on bed packing and entrainment. However, it too provided only minor adjustments to reach type delineation. Copyright © 2007 John Wiley & Sons, Ltd.     

Testing bedload transport equations with consideration of time scales

Bedload transport is known to be a highly fluctuating temporal phenomenon, even under constant (mean) flow conditions, as a consequence of stochasticity, bedform migration, grain sorting, hysteresis, or sediment supply limitation. Because bedload transport formulas usually refer to a single mean transport value for a given flow condition, one can expect that prediction accuracy (when compared to measurements) will depend on the amplitude and duration of fluctuations, which in turn depend on the time scale used for observations. This paper aims to identify how the time scale considered can affect bedload prediction. This was done by testing 16 common bedload transport formulas with four data sets corresponding to different measurement period durations: (i) highly fluctuating (quasi‐)instantaneous field measurements; (ii) volumes accumulated at the event scale on two small alpine gravel‐bed rivers, potentially affected by seasonal fluctuations; (iii) volumes accumulated at the interannual scale in a meandering gravel bed river, thought to be weakly subject to fluctuations; (iv) time‐integrated flume measurements with nearly uniform sediments. The tests confirmed that the longer the measurement period, the better the precision of the formula's prediction interval. They also demonstrate several consequential limitations. Most threshold formulas are no longer valid when the flow condition is below two times the threshold condition for the largest elements' motion on the bed surface (considering D₈₄). In such conditions, equations either predict zero transport, or largely overestimate the real transport, especially when D₈₄ is high. There is a need for new sediment data collected with highly reliable techniques such as recording slot bedload samplers to further investigate this topic. Copyright © 2012 John Wiley & Sons, Ltd.     

Defining phases of bedload transport using piecewise regression

Differences in the transport rate and size of bedload exist for varying levels of flow in coarse‐grained channels. For gravel‐bed rivers, at least two phases of bedload transport, with notably differing qualities, have been described in the literature. Phase I consists primarily of sand and small gravel moving at relatively low rates over a stable channel surface. Transport rates during Phase II are considerably greater than Phase I and more coarse grains are moved, including material from both the channel surface and subsurface. Transition from Phase I to Phase II indicates initiation and transport of grains comprising the coarse surface layer common in steep mountain channels. While the existence of different phases of transport is generally acknowledged, the threshold between them is often poorly defined. We present the results of the application of a piecewise regression analysis to data on bedload transport collected at 12 gravel‐bed channels in Colorado and Wyoming, USA. The piecewise regression recognizes the existence of different linear relationships over different ranges of discharge. The inflection, where the fitted functions intersect, is interpreted as the point of transition from Phase I to Phase II transport; this is termed breakpoint. A comparison of grain sizes moved during the two phases shows that coarse gravel is rarely trapped in the samplers during Phase I transport, indicating negligible movement of grains in this size range. Gravel larger than about D₁₆ of the channel surface is more consistently trapped during Phase II transport. The persistence of coarse gravel in bedload samples provides good evidence that conditions suitable for coarse grain transport have been reached, even though the size of the sediment approaches the size limits of the sampler (76 mm in all cases). A relative breakpoint (R_br) was defined by the ratio between the discharge at the breakpoint and the 1·5‐year flow (a surrogate for bankfull discharge) expressed as a percentage. The median value of R_br was about 80 percent, suggesting that Phase II begins at about 80 percent of the bankfull discharge, though the observed values of R_br ranged from about 60 to 100 percent. Variation in this value appears to be independent of drainage area, median grain size, sorting of bed materials, and channel gradient, at least for the range of parameters measured in 12 gravel‐bed channels. Published in 2002 by John Wiley & Sons, Ltd.     

The anatomy of effective discharge: the dynamics of coarse sediment transport revealed using continuous bedload monitoring in a gravel‐bed river during a very wet year

Indirect, passive approaches for monitoring coarse bedload transport could allow cheaper, safer, higher‐resolution, longer‐term data that revolutionises bedload understanding and informs river management. Here, insights provided by seismic impact plates in a downstream reach of a flashy gravel‐bed river (River Avon, Devon, UK) are explored in the context of plate performance. Monitoring of a centrally‐situated plate (IP1) during an extremely wet 12‐month period demonstrated that impacts were related to discharge as a measure of transport potential (R² = 0.38) but that factors other than transport limitations are important. Analysis of discrete flow events revealed consistent rising‐limb and falling‐limb impact spikes biased toward the latter for larger events. Such patterns may result from disruption of the upstream armour layer (rising limb) and supply enhancements related to both upstream mass bank failures and/or flood routing of non‐local sediment sources (falling limb). Installation of additional impact plates indicated that plate IP1 was indeed dominantly related to instantaneous discharge, that a three‐plate lateral array somewhat better explained impact variability (R² = 0.49), and that the bedload track shifts laterally with discharge. Aggregating event‐total IP1 impacts against volumetric discharge further increases explanation as intra‐event and stochastic bedload factors are subsumed but left 26% unexplained variance related to the unsampled bedload mass, inter‐event supply differences, and attributes of plate performance. Annualising the data created an impact‐based 'effective discharge’ for this extremely wet year that was closer to morphological bar‐full in magnitude than bankfull, but the preceding results imply this outcome is related as much to supply limitations as transport limitations. Overall, passive approaches offer a liberating prospect for bedload monitoring, capable of producing insights only achievable through high resolution, extended time periods. Such results could potentially inform threshold conditions and geomorphological effectiveness of flows for future river management strategies. Copyright © 2015 John Wiley & Sons, Ltd.     

Displacement and transport of marked pebbles,cobbles and boulders during floods in a steep mountain stream

In a small experimental catchment of the Dolomites (Rio Cordon, 5 km²) field observations have been carried out on the movement of various sized bed material particles. Displacement length of 860 marked pebbles, cobbles and boulders (0·032 < D < 0·512 m) has been measured along the river bed during individual snowmelt and flood events in the periods 1993–1994 and 1996–1998. Floods were grouped into two categories. The first includes ‘ordinary’ events, which are characterized by peak discharges with a return period of 1–5 years and by an hourly bedload rate not exceeding 20 m³ h^?1. The second refers to ‘exceptional’ events with a return period of 50–60 years. A flood of this latter type occurred on 14 September 1994, with a peak discharge of 10·4 m³ s^?1 and average hourly bedload rate of 324 m³ h^?1. The variation according to grain size of total displacement length L_i depends on the degree of mobilization of the individual fractions of the bed surface: L_i is independent of D_i for smaller, fully mobile grain sizes and decreases rapidly with D_i for larger fractions in a state of partial transport. Sustained selective transport without a supply of sediment from upstream leads to the development of a stable coarse armoured surface through progressive winnowing of finer material from the bed surface. With supply unlimited conditions for transport, both the occurrence of extreme events and the duration of a sequences of ‘ordinary’ floods play an important role in the degree of mobilization of the individual fractions of the bed. Copyright © 2004 John Wiley & Sons, Ltd.     

The impact of inter-flood duration on non-cohesive sediment bed stability

Limited field and flume data suggests that both uniform and graded beds appear to progressively stabilize when subjected to inter-flood flows as characterized by the absence of active bedload transport. Previous work has shown that the degree of bed stabilization scales with duration of inter-flood flow, however, the sensitivity of this response to bed surface grain size distribution has not been explored. This article presents the first detailed comparison of the dependence of graded bed stability on inter-flood flow duration. Sixty discrete experiments, including repetitions, were undertaken using three grain size distributions of identical D₅₀ (4.8 mm); near-uniform (σ_g = 1.13), unimodal (σ_g = 1.63) and bimodal (σ_g = 2.08). Each bed was conditioned for between 0 (benchmark) and 960 minutes by an antecedent shear stress below the entrainment threshold of the bed (τ*_c50). The degree of bed stabilization was determined by measuring changes to critical entrainment thresholds and bedload flux characteristics. Results show that (i) increasing inter-flood duration from 0 to 960 minutes increases the average threshold shear stress of the D₅₀ by up to 18%; (ii) bedload transport rates were reduced by up to 90% as inter-flood duration increased from 0 to 960 minutes; (iii) the rate of response to changes in inter-flood duration in both critical shear stress and bedload transport rate is non-linear and is inversely proportional to antecedent duration; (iv) there is a grade dependent response to changes in critical shear stress where the magnitude of response in uniform beds is up to twice that of the graded beds; and (v) there is a grade dependent response to changes in bedload transport rate where the bimodal bed is most responsive in terms of the magnitude of change. These advances underpin the development of more accurate predictions of both entrainment thresholds and bedload flux timing and magnitude, as well as having implications for the management of environmental flow design. © 2019 John Wiley & Sons, Ltd. © 2019 John Wiley & Sons, Ltd.     

Bedload transport measurements with impact plate geophones: comparison of sensor calibration in different gravel‐bed streams

Indirect bedload transport measurements have been made with the Swiss plate geophone system in five gravel‐bed mountain streams. These geophone sensors record the motion of bedload particles transported over a steel plate mounted flush with the channel bed. To calibrate the geophone system, direct bedload transport measurements were undertaken simultaneously. At the Erlenbach in Switzerland, a moving‐basket sampler was used. At the Fischbach and Ruetz streams in Austria, a Helley–Smith type bedload sampler provided the calibration measurements. A Bunte‐type bedload trap was used at the Rofenache stream in Austria. At the Nahal Eshtemoa in Israel, Reid‐type slot bedload samplers were used. To characterize the response of the geophone signal to bedload particles impacting on the plate, geophone summary values were calculated from the raw signal and stored at one second intervals. The number of impulses, i.e. the number of peaks above a pre‐defined threshold value of the geophone output signal, correlated well with field measured gravel transport loads and was found to be a robust parameter. The relations of impulses to gravel transport loads were generally near‐linear, but the steepness of the calibration relations differed from site to site. By comparing the calibration measurements from the different field sites and utilizing insights gained during preliminary flume experiments, it has been possible to identify the main factors that are responsible for site specific differences in the calibration coefficient. The analysis of these calibration measurements indicates that the geophone signal also contains some information about the grain size distribution of bedload. Copyright © 2013 John Wiley & Sons, Ltd.     

Evolution of grain size distributions and bed mobility during hydrographs in gravel-bed braided rivers

Evolution of bed material mobility and bedload grain size distributions under a range of discharges is rarely observed in braiding gravel-bed rivers. Yet, the changing of bedload grain size distributions with discharge is expected to be different from laterally-stable, threshold, channels on which most gravel bedload theory and observation are based. Here, simultaneous observations of flow, bedload transport rate, and morphological change were made in a physical model of a gravel-bed braided river to document the evolution of grain size distributions and bed mobility over three experimental event hydrographs. Bedload transport rate and grain size distributions were measured from bedload samples collected in sediment baskets. Morphological change was mapped with high-resolution (~1 mm precision) digital elevation models generated from close-range digital photogrammetry. Bedload transport rates were extremely low below a discharge equivalent to ~50% of the channel-forming discharge (dimensionless stream power ~70). Fractional transport rates and plots of grain size distributions indicate that the bed experienced partial mobility at low discharge when the coarsest grains on the bed were immobile, weak selective mobility at higher discharge, and occasionally near-equal mobility at peak channel-forming discharge. The transition to selective mobility and increased bedload transport rates coincided with the lower threshold for morphological change measured by the morphological active depth and active width. Below this threshold discharge, active depths were of the order of D₉₀ and active widths were narrow (< 3% of wetted width). Above this discharge, both increased so that at channel-forming discharge, the active depth had a local maximum of 9D₉₀ while active width was up to 20% of wetted width. The modelled rivers approached equal mobility when rates of morphological change were greatest. Therefore, changes in the morphological active layer with discharge are directly connected to the conditions of bed mobility, and strongly correlated with bedload transport rate. © 2018 John Wiley & Sons, Ltd.     

Novel mass-aggregation-based calibration of an acoustic method of monitoring bedload flux by infrequent desert flash floods

The monitoring of bedload flux under flash flood conditions has been successfully achieved since 1992 using slot samplers in the semiarid Nahal Eshtemoa. In the present study, a surrogate bedload monitoring technique - the Japanese plate microphone - has been deployed and calibrated against data from the slot samplers. Since a slot sampler has a sensitivity threshold that becomes especially important when transport rates are low, different averaging periods should be considered for high and low fluxes. In order to overcome the deficiencies of time-based aggregation used hitherto, we have developed a new method involving mass aggregation and commensurably variable intervals, thereby enabling a more accurate analysis and optimizing the bedload sampler's capabilities. The data derived with this new method has then been utilized to calibrate the Japanese plate microphone. The Eshtemoa is an ephemeral gravel bed channel with a high proportion of fine gravel (< 0.02 m); for these conditions, acoustic sensors have not been calibrated as yet. Two multiple linear regression models incorporating the effect of median bedload grain size on pulse rate have been established to predict bedload flux and cumulative transported bedload mass. The coefficients in these models are statistically significant. Good predictions are obtained for bedload flux (adj. r² = 0.83) and for cumulative bedload mass (adj. r² = 0.98) during flood recession. Overall, the multiple linear regression models, used in conjunction with the mass aggregation method of estimating bedload flux, suggest that field calibration of acoustic devices is feasible under these conditions for ca. 90% of the duration of bedload transport. © 2020 John Wiley & Sons, Ltd.     

‘Bedload’ dynamics: Grain impacts,momentum transfer and derivation of a grain froude number

A test is proposed for Bagnold's postulate that the normal weight stress due to moving ‘bedload’ is balanced by a solid transmitted stress due to the rate of change of momentum produced by grain impacts on unit area of the stationary bed. The test involves derivation of an expression for normal momentum transfer due to saltating grains at moderate transport stages when grain-to-grain collisions and partial suspension during saltation may be ignored. A dimensionless number, Φ, (a grain Froude Number) is derived, given by ū²/g where ū is the mean grain forward velocity, g is the gravitational acceleration and L? is the length of a single saltation ‘jump’. Equilibrium demands that Φ be unity during bedload transport involving saltating grains if Bagnold's postulate is correct. Experimental data shows Φ < 1, the discrepancy between theory and experiment being due to the existence of lift forces acting upon bedload grains. Bagnold's postulate is correct for concentrated dispersions of grains, as in grain flows, when fluid lift forces may be neglected due to high particle concentration.     

Transport measurement with a horizontal and a vertical pipe microphone in a mountain stream: taking account of particle saltation

The pipe microphone has been shown to be an effective means for monitoring bedload transport in mountain streams. It is commonly installed perpendicular to the flow direction on a stable river bed, such as that of a check dam. Acoustic pulses caused by bedload collisions with the pipe are detected by a microphone. However, bedload particles saltating over the pipe remain undetected. To overcome this disadvantage, we installed a horizontal as well as a vertical pipe microphone in the Ashi‐arai‐dani supercritical channel located in the Hodaka mountain range, Japan. The vertical pipe was installed on the wall of the channel and the horizontal pipe was installed on the channel bed. The acoustic response of the horizontal pipe is expected to be larger than that of the vertical pipe, because the bedload concentration decreases with increasing height above the bed. However, at high amplifications, the peak pulse value from the vertical pipe is higher than that from the horizontal pipe. We explain this observation as follows: under high bedload discharge conditions, the pulses of the horizontal pipe are saturated but those of the vertical pipe are not. We proposed a ratio (R_hv) between the pulses detected by these sensors, and applied this ratio for calibrating the contemporaneous pulses detected by a microphone located immediately upstream of a bedload slot sampler. Indeed the R_hv‐corrected pulses correlated well with the bedload discharge calculated from the sampler, supporting our explanation. We conclude that bedload monitoring using concomitant vertical and horizontal pipe microphones can be used to calibrate centrally located pipe microphones when the bedload concentration is approximately homogeneous laterally across the width of the channel cross‐section, and thereby represent bedload discharges more accurately than with only a single pipe microphone. Copyright © 2017 John Wiley & Sons, Ltd.     

Sediment mobility and bedload transport conditions in an alpine stream

The mobility conditions of bedload transport in an alpine high‐gradient step–pool stream (Rio Cordon) are analysed. Since 1986, a device system at the downstream end section of the stream has been operating in order to monitor the water discharge, suspended sediment and bedload transport. Sediment distribution of bedload transported by various floods has been analysed, and equal‐mobility evidence is recognized only for the high‐magnitude flows ever recorded (RI > 50 years). The thresholds for size‐selective and equal‐mobility transport conditions are identified and quantified by using both data provided by the fractional transport rate and by length displacements of marked particles. Size‐selective bedload transport seems to dominate when the critical shear stress of the size fractions τ_ci considered is exceeded, whereas the equal‐mobility condition is approached as levels of excess shear stress become higher (τ_eqi = 1·45τ_ci). Copyright © 2006 John Wiley & Sons, Ltd.     

Bedload transport resistance in rough open‐channel flows

During bedload movement by saltation, streamwise momentum is transferred from the ?ow to the saltating grains. When the grains collide with other grains on the bed or in the ?ow, streamwise momentum is reduced, and there is a decrease in streamwise ?ow velocity and an increase in ?ow resistance, herein termed bedload transport resistance f_bt. Based on experiments in two ?umes with ?xed and mobile plane beds and previously published data, an equation is developed that may be used to predict f_bt for both capacity and non‐capacity ?ows. The variables in this equation are identi?ed by dimensional analysis and the coef?cients are determined by non‐linear regression. This equation applies to rough turbulent open‐channel ?ows, where the relative submergence is between 1 and 20 and the entire sediment load moves by saltation. An investigation of the relative magnitudes of f_bt and grain resistance f_c suggests that where dimensionless shear stress θ is less than 1 and saltation is the dominant mode of bedload transport, f_bt/f_c increases with θ but never exceeds 1. Copyright © 2004 John Wiley & Sons, Ltd.     

Patterns of bedload entrainment and transport in forested headwater streams of the Columbia Mountains,Canada

We monitor bedload transport and water discharge at six stations in two forested headwater streams of the Columbia Mountains, Canada. The nested monitoring network is designed to examine the effects of channel bed texture, and the influence of alluvial (i.e. step pools and riffle pools) and semialluvial morphologies (i.e. boulder cascades and forced step pools) on bedload entrainment and transport. Results indicate that dynamics of bedload entrainment are influenced by differences in flow resistance attributable to morphology. Scaled fractional analysis shows that in reaches with high form resistance most bedload transport occurs in partial mobility fashion relative to the available bed material, while calibers finer than 16 mm attain full mobility during bankfull flows. Equal mobility transport for a wider range of grain sizes is achieved in reaches exhibiting reduced form resistance. Our findings confirm that the Shields value for mobilization of the median surface grain size depends on channel gradient and relative submergence; however, we also find that these relations vary considerably for cobble and gravel bed channels due to proportionality between dimensionless shear stress and grain size. Exponents of bedload rating curves across sites correlate most with the D_90s of the mobile bed, however, where grain effects are controlled (i.e. along individual streams), differences in form resistance across morphologies exert a primary control on bedload transport dynamics. Application of empirical formulae developed for use in steep alpine channels present variable success in predicting transport rates in forested snowmelt streams. Formulae that explicitly account for reductions in mobile bed area and high morphological resistance associated with woody debris provide the best approximation to observed empirical data. Copyright © 2014 John Wiley & Sons, Ltd.     

Increase in coarse sediment transport associated with disturbance of gravel river beds by signal crayfish (Pacifastacus leniusculus)

There is growing acknowledgement of the interaction between animals and the river bed on which they live and the implications of biological activity for geomorphic processes. It has been observed that signal crayfish (Pacifastacus leniusculus) disturb gravel substrates, potentially promoting sediment transport and impacting ecological communities. However, the mechanisms involved and the extent of their impact remain poorly understood, especially in relation to other processes that affect grain mobility in gravel‐bed rivers. A series of flume experiments, using loose and water‐worked gravel beds of narrowly graded grain sizes that were exposed to 6 h of crayfish activity under low‐velocity flows, showed a substantial increase in the number of grains entrained by subsequent higher‐velocity flows when compared with control runs in which crayfish were never introduced. Crayfish alter the topography of their substrate by constructing pits and mounds, which affect grain protrusion. When walking and foraging, they also alter gravel fabric by reorienting and changing the friction angle of surface grains. In water‐worked surfaces, this fabric rearrangement is shown to lead to a statistically significant, partial reversal of the structuring that had been achieved by antecedent flow. For these previously water‐worked surfaces, the increase in entrainment arising from disturbance by crayfish was statistically significant, with grain transport nearly twice as great. This suggests that signal crayfish, an increasingly widespread invasive species in temperate latitudes beyond their native NW North America, have the potential to enhance coarse‐grained bedload flux by altering the surface structure of gravel river beds and reducing the stability of surface grains. This study illustrates further the importance of acknowledging the impact of mobile organisms in conditioning the river bed when assessing sediment entrainment mechanics in the context of predicting bedload flux. Copyright © 2011 John Wiley & Sons, Ltd.     

Monitoring gravel augmentation in a large regulated river and implications for process‐based restoration

The artificial gravel augmentation of river channels is increasingly being used to mitigate the adverse effects of river regulation and sediment starvation. A systematic framework for designing and assessing such gravel augmentations is still lacking, notably on large rivers. Monitoring is required to quantify the movement of augmented gravel, measure bedform changes, assess potential habitat enhancement, and reduce the uncertainty in sediment management. Here we present the results of an experiment conducted in the Rhine River (French and German border). In 2010, 23 000 m³ of sediments (approximately the mean annual bedload transport capacity) were supplied in a by‐passed reach downstream of the Kembs dam to test the feasibility of enhancing sediment transport and bedform changes. A 620‐m‐long and 12‐m‐wide gravel deposit was created 8 km downstream from the dam. Monitoring included topo‐bathymetric surveys, radio‐frequency particle tracking using passive integrated transponder (PIT) tags, bed grain size measurement, and airborne imagery. Six surveys performed since 2009 have been described (before and after gravel augmentation, and after Q₂ and Q₁₅ floods). The key findings are that (i) the augmented gravel was partially dispersed by the first flood event of December 2010 (Q₁); (ii) PIT tags were found up to 3200 m downstream of the gravel augmentation site after four years, but the effects of gravel augmentation could not be clearly distinguished from the effects of floods and internal remobilization on more than 3500 m downstream; (iii) linear and log‐linear relationships linking bedload transport, particle mobility, and grain size were established; and (iv) combined bathymetry and PIT tag surveys were useful for evaluating potential environmental risks and the first morpho‐ecological responses. This confirmed the complementary nature of such techniques in the monitoring of gravel augmentation in large rivers. Copyright © 2017 John Wiley & Sons, Ltd.