AAC算法的大气校正复合改进算法

利用模拟数据,评价Autonomous Atmospheric Compensation(AAC)算法的抗噪性,认为AAC算法的抗噪性较弱。基于TASI实测数据,利用AAC算法开展反演计算时,计算结果呈现出多样性问题。结合In-scene Atmospheric Compensation(ISAC)算法中黑体像元的标定方法,提出了一种复合改进算法。首先,利用ISAC算法反演的大气透过率和路径辐射,重新计算AAC算法中大气透过率之比(Tr)和相邻两强弱吸收通道的路径辐射之差(Pd),再次,运用经验公式获得稳定的大气反演结果(大气透过率和路径辐射),有效解决了计算结果多样性的问题。利用复合改进算法,开展的温度与发射率分离实验,证明反演得到的发射率波谱更接近野外实测波谱。     

高光谱热红外星上辐亮度图像模拟及初步应用

基于卫星数据的热红外图像模拟可以为热红外大气校正、地表温度和发射率反演和前期验证提供数据支撑,同时也可以为热红外传感器的波段设置和优化提供参考。热红外图像模拟是进行热红外定量遥感研究的有效手段。本研究利用Terra星上搭载的ASTER（Advanced Spaceborne Thermal Emission and Reflection Radiometer）遥感数据所反演得到的地表温度和发射率产品,基于高光谱辐射传输模型,模拟8—14 μm（714—1250 cm^-1）,波谱分辨率为0.25 cm^-1的星上TOA（Top of Atmosphere）高光谱热红外成像模拟数据。在此基础上,结合高光谱热红外图像数据的特点,实现了温度和发射率分离算法,以及对比了不同的基于图像的大气校正算法。结果显示,本文提出的热红外图像模拟方法可行,能够为评价不同的大气校正、温度和发射率分离算法提供有效的数据支撑。     

高光谱红外传感器在轨光谱定标

高光谱红外传感器高精度在轨光谱定标是红外遥感定量反演及应用的重要前提。本文针对大气红外探测仪AIRS（Atmospheric Infrared Sounder）的观测数据,分析传感器等效入瞳亮温与大气透过率光谱中的吸收线特征,基于NODD和包络线去除的光谱归一化处理,融合多种光谱匹配算法构建非线性代价函数,提出了一种无需地表实测数据支持的高光谱红外传感器光谱定标方法。与JPL官方定标结果相比,中心频率定标精度优于0.0154 cm^-1,中心频率及半峰全宽的偏移量分别在±0.02 cm^-1及±0.1 cm^-1以内,相对偏移量分别在0.2%—1.9%与0.5%—12.0%。最后,本文详细分析了大气上行辐射、下垫面类型及空间采样点数量对定标算法的影响。     

高光谱热红外遥感：现状与展望

高光谱热红外数据中蕴含着丰富的长波光谱信息,可以更精细的揭示地气耦合过程导致的辐射变化,反映热红外谱段特有的地物诊断特征,同时高光谱特性也可以为热红外关键特征参数的病态反演问题提供更合理的假设和约束条件,具有重要的研究价值和应用前景。高光谱热红外遥感技术自诞生起,在吸纳多光谱热红外遥感技术的基础上迅速发展,成为热红外遥感领域的重要研究方向和突破点。然而,当前高光谱热红外遥感存在着可用数据不足,处理方法传统,反演精度有限,应用难以有效实施等问题。为进一步明晰高光谱热红外遥感的研究进展和现存挑战,本文在高光谱热红外相关文献深入分析的基础上,梳理了高光谱热红外研究的发展脉络和热点,介绍了现有国内外主要的高光谱热红外传感器,分析了高光谱大气效应校正、地表温度和发射率分离以及地气关键特征参数一体化反演的现状和问题,总结了相关典型行业应用,展望了高光谱热红外的发展方向,以期为未来高光谱热红外研究工作的开展提供借鉴和帮助。     

内蒙古辐射校正场特性评价与应用潜力分析

利用2010年6月在内蒙古贡格尔辐射校正场(简称内蒙古辐射校正场)实测的地表反射率和大气气溶胶数据,分析了该辐射校正场的地表反射率和大气气溶胶特性,并与敦煌辐射校正场相关数据进行了对比分析.结果表明:内蒙古辐射校正场地表反射率的相对方差小于5％,表现出较好的均一性;在天气晴朗的情况下,各通道的大气气溶胶光学厚度可达0....     

基于辐射传输模型的Hyperion光谱重建应用评价

光谱重建是高光谱数据定量分析的前提,大气校正是光谱重建的关键环节。对于缺少地面同步测量的高光谱数据,大气辐射传输模型是最可行的大气校正方法。应用当前流行的大气辐射传输模型MODTRAN 4.0和6S,分别对试验区EO-1 Hyperion高光谱数据进行大气校正和光谱重建。通过对植被、粘土矿及水体3类地物光谱重建结果的对比分析,并利用统计方法计算光谱重建精度,评价大气辐射传输模型校正的效果和模型的适用性。最后,通过FLAASH模型的试验体现了高光谱数据大气校正集成化处理的优越性。     

基于劈窗算法从ASTER遥感数据反演地表温度

应用卫星热红外遥感影像反演地表温度对于研究城市生态环境、气象过程具有重要意义,ASTER 遥感数据为此提供了有效的信息源。针对从 ASTER 数据中反演地表温度(LST)的需要,首先利用 MODIS 数据反演大气水汽含量,并模拟出大气水汽含量与大气透过率的关系,求得大气透过率,然后通过决策树分类结果和地物光谱特征计算出地表反射率,最后采用劈窗算法反演出地表温度。通过某市2个季节的试验表明该方法具有较高的精度,能够有效应用于城市热环境分析,为城市物理环境综合分析评价提供支持。     

天宫一号数据地表温度反演及其在城市热岛效应中的应用

针对天宫一号高光谱成像仪红外波段数据提出了一个单通道地表温度反演算法,算法的输入参数为大气水汽含量和地表发射率.利用模拟数据和黑河流域生态—水文过程综合遥感观测联合试验的地面实测数据对算法进行了精度评价,结果表明算法的均方根误差为2.72 K,能够满足大多数应用研究的需求.以北京市二环以内为研究区域,采用4个时相的天宫一号高光谱红外波段数据进行了城市热岛效应研究,结果表明天宫一号高光谱红外波段数据适合用来进行街区尺度的城市热岛效应研究,具有很大的应用潜力.     

机载高光谱热红外数据的地表温度和发射率反演与应用

机载高分辨率遥感是高分对地观测的重要部分,其中高分辨率高光谱热红外数据的光谱发射率可以用于矿物识别,是对可见光遥感地物识别的有效补充。机载高光谱热红外传感器TASI（Thermal Airborne Hyperspectral Imager）在8—11.5 μm范围内设置了32个波段,在国内外常被用于地表热辐射信息、矿产资源探测等领域。本文利用2018-10在新疆富蕴县研究区的TASI航空飞行数据,首先基于再分析大气廓线NCEP数据与MODTRAN实现了TASI高光谱热红外数据的大气校正,并在基础上发展了温度与发射率分离方法TES（Temperature and Emissivity Separation method）反演研究区地表温度与发射率,采用多波段热辐射计CE312测量的地面发射率对反演结果进行了有效验证,结果表明波长大于9.6 μm的波段的发射率误差约为0.01。最后,结合反演的TASI发射率光谱曲线,采用光谱角度匹配方法提取了研究区高岭石的空间分布。研究工作涉及的相关算法与应用成果可为星载高分辨率热红外载荷数据的应用提供了相关参考。     

EO-1Hyperion高光谱数据FLAASH模块大气纠正及评价

由于受到大气的影响,传感器接收到的辐射信息不能真实地反映地表反射光谱信息,因此,从遥感影像中去除大气的影响,即进行大气校正,是高光谱遥感数据处理中极为重要的环节。文章介绍了EO-1hyperion高光谱数据的特点,以及用FLAASH（Fast Line of Sight Atmospheric Analysis of ...     

遥测地表温度与比辐射率的迭代反演方法──理论推导与数值模拟

首先在地表比辐射率为已知的条件下,提出一个非线性迭代温度反演模型,我们对不同的地表和大气条件进行了模拟计算,结果表明当大气温度廓线误差－２Ｋ－２Ｋ,水汽廓线误差±２０％时的温度均方根误差为０．４８Ｋ。当大气模式误差一个模式时反演的温度均方根误差为０．８５Ｋ。在此基础上,引人相邻像元的概念,相邻像元的大气状况可以认为是相同的,应用两个时相的遥感影像数据,假定在两个相近时相之间地表比辐射率值不变,建立地表比辐射率与温度的反演模型。我们对不同的地表和大气条件进行了模拟计算,结果表明当大气温度廓线误差－２Ｋ－２Ｋ,水汽廓线误差±２０％时地表温度均方根误差小于１．５Ｋ,地表比辐射率均方根误差小于０．０２,地表辐射均方根误差为１％;当大气温度廓线误差－２Ｋ－２Ｋ,水汽廓线误差±１０％时,地表温度均方根误差小于１．０Ｋ,地表辐射均方根误差小于０．６％。     

Retrieval of land surface temperature (LST) from landsat TM6 and TIRS data by single channel radiative transfer algorithm using satellite and ground-based inputs

The present study proposes land surface temperature (LST) retrieval from satellite-based thermal IR data by single channel radiative transfer algorithm using atmospheric correction parameters derived from satellite-based and in-situ data and land surface emissivity (LSE) derived by a hybrid LSE model. For example, atmospheric transmittance (τ) was derived from Terra MODIS spectral radiance in atmospheric window and absorption bands, whereas the atmospheric path radiance and sky radiance were estimated using satellite- and ground-based in-situ solar radiation, geographic location and observation conditions. The hybrid LSE model which is coupled with ground-based emissivity measurements is more versatile than the previous LSE models and yields improved emissivity values by knowledge-based approach. It uses NDVI-based and NDVI Threshold method (NDVI^THM) based algorithms and field-measured emissivity values. The model is applicable for dense vegetation cover, mixed vegetation cover, bare earth including coal mining related land surface classes. The study was conducted in a coalfield of India badly affected by coal fire for decades. In a coal fire affected coalfield, LST would provide precise temperature difference between thermally anomalous coal fire pixels and background pixels to facilitate coal fire detection and monitoring. The derived LST products of the present study were compared with radiant temperature images across some of the prominent coal fire locations in the study area by graphical means and by some standard mathematical dispersion coefficients such as coefficient of variation, coefficient of quartile deviation, coefficient of quartile deviation for 3rd quartile vs. maximum temperature, coefficient of mean deviation (about median) indicating significant increase in the temperature difference among the pixels. The average temperature slope between adjacent pixels, which increases the potential of coal fire pixel detection from background pixels, is significantly larger in the derived LST products than the corresponding radiant temperature images.     

单窗算法的大气参数估计方法

根据地表热辐射传导方程,提出了一个简单可行且精度较高的专门用于从TM6数据中演算地表温度的方法——单窗算法.这一算法把大气和地表状态对地表热传导的影响直接包括在演算公式中.该方法需要两个大气参数进行地表温度的演算,即大气平均作用温度和大气透射率.本文论述这两个大气参数的估计方法:根据大气水分含量或地表附近空气湿度来估计大气透射率;通过分析标准大气剖面资料,尤其是大气水分和气温随高程的变化规律,根据地表温度推算大气平均作用温度.     

一种适用于ASTER数据同时反演大气水汽含量和地表温度的三通道算法

提出了针对ASTER数据同时反演大气水汽含量与地表温度的三通道算法,即利用ASTER数据的第12,13,14三个热红外波段建立三个热辐射传输方程。再利用MODTRAN软件分别模拟ASTER 12,13,14波段透过率与大气水汽含量的关系,通过分析可知ASTER三个热红外波段的透过率与大气水汽含量的关系可用近似线性方程表示,从而得到另外三个方程。这样就构成了一个包含六个未知数、六个方程的方程组,形成了针对ASTER数据同时反演大气水汽含量与地表温度的三通道算法。由于各参数都可以通过方程组计算出来,所以,这种算法仅需要ASTER数据就可反演出大气水汽含量与地面温度,且关键参数大气透过率的计算精度提升到了AS-TER数据一个像元（15×15）m2的程度。     

A coupled atmospheric and topographic correction algorithm for remotely sensed satellite imagery over mountainous terrain

Radiometric correction is an important issue in the quantitative remote-sensing community. By integrating dark object subtraction (DOS)-based atmospheric correction with physics-based topographic correction, a coupled land surface reflectance retrieval algorithm (coupled atmospheric and topographic correction algorithm, named the CAT algorithm) for rugged mountainous regions is proposed. Terra MODIS-derived atmospheric characterization data (including aerosol optical depth, integrated precipitable water, surface pressure, and ozone concentration) are employed as inputs for the proposed algorithm. A physics-based path radiance estimation model is proposed and embedded in the CAT algorithm, and band-specific per-pixel path radiance values are calculated. After the CAT algorithm was performed, the correlation between reflectance and terrain was dramatically reduced, with correlation coefficients nearly equal zero, especially for the near infrared and short-wave infrared bands, meanwhile the image information content increased over 20%. To provide a comparison with previous studies, two commonly used methods in the literature (DOS + Cosine and DOS + C) were employed. The results of the comparison show that the proposed algorithm performed better in both atmospheric and topographic corrections without empirical regression.     

比辐射率封闭法测定技术及误差分析

劈窗算法是目前由热红外遥感图像数据获取陆面温度最主要的方法。由于进行地面像元尺度实时陆面温度同步测量的困难,尚无法直接对现有各劈窗算法进行评判。该文借助于辐射传输模型ＬＯＷＴＲＡＮ７及其提供的６ 种标准大气模式,进行模拟计算,分析了６ 种主要劈窗算法对大气廓线误差和比辐射率的敏感度,作为对劈窗算法适用性的一间接判据。     

Contribution of Landsat 8 data for the estimation of land surface temperature in Batna city,Eastern Algeria

In this study, we presented a mono-window (MW) algorithm for land surface temperature retrieval from Landsat 8 TIRS. MW needs spectral radiance and emissivity of thermal infrared bands as input for deriving LST. The spectral radiance was estimated using band 10, and the surface emissivity value was derived with the help of NDVI and vegetation proportion parameters for which OLI bands 5 and 4 were used. The results in comparison with MODIS (MOD11A1) products indicated that the proposed algorithm is capable of retrieving accurate LST values, with a correlation coefficient of 0.850. The industrial area, public facilities and military area show higher surface temperature (more than 37 °C) in comparison with adjoining areas, while the green spaces in urban areas (34 °C) and forests (29 °C) were the cooler part of the city. These successful results obtained in the study could be used as an efficient method for the environmental impact assessment.     

同化MODIS温度产品估算地表水热通量

基于集合卡尔曼滤波和通用陆面模型(CLM 1.0)发展了一个地表温度的同化系统。这个系统同化了MODIS温度产品, 并将MODIS的叶面积指数引入CLM模型中, 主要用于改进地表水热通量的估算精度。将CLM输出的地表温度与MODIS地表温度建立关系, 并作为同化系统的观测算子。将MODIS地表温度与实测地表温度进行了比较, 将其均方差(Root Mean Square Error, RMSE)作为观测误差。选取3个美国通量网站点(Blackhill、Bondville、Brookings)作为实验数据, 结果表明: 同化结果中地表温度、显热通量的估算精度均有提高。其中Blackhill站的估算精度改进最大, 均方差由81.5W·m-2减小到58.4W·m-2, Bondville站均方差由47.0W·m-2减小到31.8W·m-2, Brookings站均方差由46.5W·m-2减小到45.1W·m-2。潜热通量估算精度在Bondville站均方差由88.6W·m-2减小到57.7W·m-2, Blackhill站均方差由53.4W·m-2减小到47.2W·m-2。总之, 结合陆面过程模型同化MODIS温度产品估算地表水热通量是可行的。     

Examining the impacts of urbanization on surface radiation using Landsat imagery

Metropolitan Beijing is facing many environmental problems such as haze and urban heat island due to the rapid urbanization. Surface shortwave, longwave, and net radiations are key components of the surface-atmosphere radiation budget. Since megacities are affected by the thermal radiation of complex landscape structures and atmospheric environments, quantitative and spatially explicit retrieval from remotely sensed data remains a challenge. We collected the surface radiation fluxes from seven fixed sites representing different land-use types to calibrate the local parameters for remotely sensed retrieval of net radiation. We proposed a remote sensing–based surface radiation retrieval method by embedding the underlying land covers and integrating the observational data. The improved method is feasible to accurately retrieve surface radiation and delineate spatial characteristics in metropolitan areas. The accuracy evaluation indicated that the difference between remotely sensed and in situ observed net radiation ranged within 0~± 40 W· m^?2. The root mean squared error of the estimated net surface radiation was 32.71 W· m^?2. The strongly spatial heterogeneity of surface radiation components in metropolitan Beijing was closely related to land-cover patterns from urban area to outskirts. We also found that the surface net radiation had a decreasing trend from 1984 to 2014, and the net radiation in the urban area was lower than that in the outskirts. According to the surface radiation budgets, urbanization resulted in the cooling effect in net radiation flux in the daytime, which was stemmed from low atmospheric transmittances from massive aerosol concentration and high surface albedo from light building materials.