河南老湾金矿床成矿流体性质与同位素地球化学示踪

老湾金矿床是河南桐柏地区典型的剪切带型金矿床。流体包裹体特征显示成矿流体为中低温、低盐度的含CO_2的K~+-Na~+-Cl~-SO_4~(2-)体系;氢氧同位素研究结果显示矿床成矿早期阶段以岩浆水为主要成矿热液来源,成矿晚期阶段以大气降水为主要热液来源:矿石铅同位素特征显示成矿物质源区与龟山岩组、老湾花岗岩有亲缘关系,且与花岗岩接近,显示其深源特征,进一步提供了成矿流体岩浆成因的证据。     

胶东中生代花岗岩及大型-超大型金矿床形成的地球动力学环境

文章通过对大量前人构造地质学、同位素年代学等多元信息资料的分析,认为胶东中生代花岗岩和大型-超大型金矿床形成于华南-华北克拉通后碰撞挤压和伊泽奈崎板块快速斜冲剪切的双重构造环境及其后的拉张构造环境。胶东大型-超大型金矿床受控于经历了韧-脆性剪切、挤压-拉张复杂变形叠加的大型构造岩带,同时也受控于被断裂叠加的花岗岩接触带。根据铅、硫等同位素组成特征及地质构造环境的综合分析,认为成矿物质主要来自以太古宙胶东岩群绿岩和深成岩组成的结晶基底,不排除煌斑岩浆带来部分深源物质;根据流体包裹体的氢、氧、碳同位素组成,判断成矿流体为大气水和岩浆水的混合流体;成矿条件为中低温（380～100℃）,低压（86～5．4MPa）;成矿时代为燕山晚期（125～100Ma）,成矿与燕山晚期拉张环境下的岩浆活动有成因联系,属环太平洋成矿带中温热液金矿床。     

祁雨沟地区金矿床稳定同位素研究

对河南嵩县祁雨沟地区角砾岩型金矿床和蚀变岩型金矿床稳定同位素研究表明，两类矿床具有同一成矿流体来源－岩浆水；在早期－主期成矿阶段成矿流体以岩浆水为主，晚期矿化流体加入了相当数量的大气水。铅同位素组成表明金矿床的成矿物质与区内钙碱性花岗岩成岩皆主要来源自上地幔，混合铅的存在指示了上地壳地矿物质加入岩浆热液中，参与了金床床的成矿作用。     

胶东金矿成矿流体同位素的地质特征

胶东大、中型金矿床成矿流体的Ｈ、Ｏ同位素组成显示出金矿床的初生成矿流体以岩浆水为主,在重熔花岗岩形成作用中继承了部分变质水,在高温阶段的成矿作用中以岩浆水为主,其后逐渐向大气降水方向演化,只有少部分矿床属大气降水成因。本文探讨了Ｈ．Ｐ．泰勒的水岩反应同位素交换质量平衡方程的应用条件,当水／岩比很小时,该方程不能确切判定关于成矿流体的成因,本文提供了以地质条件为前提的解析方法。成矿流体的Ｒｂ－Ｓｒ年龄揭示出胶东金矿主要成矿期为燕山晚期,成矿流体的ＩＳｒ与玲珑花岗质杂岩体中的郭家店、郭家岭型岩体一致,而成矿作用特别是与郭家岭型岩体重熔形成作用有关。     

冀东地区东梁金矿床地质特征及成因

东梁矿区位于冀东地区宽城凹褶束东南边缘。金矿床主要产于燕山期火成岩与中元古界长城系、蓟县系碳酸盐岩地层的接触带部位,受构造、岩浆活动控制。矿区岩(矿)石地球化学分析结果表明,成矿流体中的硫、铅主要来源于深部,与深部岩浆活动有关;氢、氧同位素分析结果显示,成矿流体主要来源于原生岩浆水;金矿床成矿温度125~305℃,成矿深度1.5km,成矿时代为燕山期火山活动晚期。认为在燕山期板块构造影响下,东梁金矿床成矿物质主要来源于深部活化变质岩系,属岩浆热液型中低温金矿床。     

辽宁丹东四道沟金矿床流体包裹体特征及矿床成因

四道沟金矿床为辽东南地区重要的蚀变岩型矿床,其空间产出受断裂构造、盖县组变质地层及区内岩浆活动的联合制约.流体包裹体研究表明:成矿早期流体为中温、低盐度且富含CO2及CH4等挥发分的热液;主成矿阶段成矿流体为中温、高盐度的热液体系;矿区晚期阶段矿化流体具有较低的温度及盐度特征.综合分析认为:四道沟金矿床早期成矿流体与区内燕山晚期三股流花岗闪长岩体活动有关;主成矿阶段流体可能来自其后的花岗斑岩等类脉岩活动;成矿晚期阶段流体则主要来自大气降水.四道沟金矿床是燕山晚期不同来源及性质的热液先后叠加成矿作用的产物.     

富碱侵入岩与金成矿关系：云南省姚安金矿床 成矿流体形成演化的微量元素和同位素证据

以产在姚安富碱侵入岩体内外接触带上的姚安金矿床为对象，对成矿流体形成演化过程中的微量元素和S、C同位素地球化学进行了综合研究。研究结果表明，富碱侵入岩成岩过程中分异出的岩浆流体提供了姚安金矿床早期成矿作用所必需的成矿流体；从早期成矿阶段至晚期成矿,民矿流体经历了从以岩浆流体为主的流体体系至以大气降水为主的流体体系的转变。因此，钙碱性侵入岩成岩过程中可分异出成矿流体的过程，也存在于富碱浸入岩的成岩过程中。     

黑龙江东安金矿床成因探讨

东安金矿床是黑龙江省新近发现的大型浅成热液金矿床。受断裂和隐爆角砾岩带控制，赋存于中生代陆相火山-侵入岩及晚印支期碱长花岗岩强硅化带中。成矿与火山-侵入岩作用有密切成生关系。通过对矿区内矿化围岩和基底岩石的金丰度和稀土元素特征的研究，以及对石英中包裹体测温、盐度、液相成分、氢-氧同位素特征的研究，认为该矿床的成矿物质主要来源于基底变质岩；成矿温度为144℃～348℃；成矿深度约0．2km～1．0km；成矿时代为中燕山晚期，为一浅成热液低硫型金矿床。     

河北小石门银金矿床地质地球化学特征与矿床成因

河北小石门银金矿床位于小寺沟斑岩铜钼矿床的南西侧.矿体呈脉状、透镜状,银金矿化受NNE向断裂控制,成矿与杂岩体及二长斑岩有关;矿物组合主要为中低温矿物组合,成矿温度240～365℃;流体包裹体研究表明成矿流体富硫,有较高的K ,NH4 ,Ca2 和Na ,成矿热液为岩浆热液;硫同位素分析显示,硫来源于岩浆;稀土元素分析亦表明成矿物质来自于二长斑岩及小寺沟岩体,而铅锌矿可能部分来源于地层.推断小石门银金矿床为中低温热液矿床.     

江西大背坞金矿成因探讨

从硫同位素、铜同位素、硅同位素、碳同位素及稀土元素特征等方面资料反映出大背坞金 成矿物质来源具有双桥山群地层为主，并有燕山期岩浆物质加入的双重特征；从成矿流体包裹体特征分析成矿流体主要来源于岩浆水；成矿蚀变矿物的铷－锶同位互获得等时线年龄为１１８Ｍａ；结合构造演化与构造控矿规律提出了大背坞金矿床因新认识，即属于受构造控制的中高湿岩浆热液矿床。     

Wavelength-dispersive X-ray fluorescence spectrometric determination of Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in komatiites

Komatiites are mantle-derived ultramafic volcanic rocks. Komatiites have been discovered in several States of India, notably in Karnataka. Studies on the distribution of trace-elements in the komatiites of India are very few. This paper proposes a simple, accurate, precise, rapid, and non-destructive wavelength-dispersive x-ray fluorescence (WDXRF) spectrometric technique for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in komatiites, and discusses the accuracy, precision, limits of detection, x-ray spectral-line interferences, inter-element effects, speed, advantages, and limitations of the technique. The accuracy of the technique is excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Zr, Nb, Ba, Pb, and Th and very good (within 4%) for Y. The precision is also excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th. The limits of detection are: 1 ppm for Sc and V; 2 ppm for Cr, Co, and Ni; 3 ppm for Cu, Zn, Rb, and Sr; 4 ppm for Y and Zr; 6 ppm for Nb; 10 ppm for Ba; 13 ppm for Pb; and 14 ppm for Th. The time taken for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in a batch of 24 samples of komatiites, for a replication of four analyses per sample, by one operator, using a manual WDXRF spectrometer, is only 60 hours.     

硅酸盐类样品中硅、铁、铝、钛、锰、钙、镁、钾、钠和磷的x射线荧光光谱测定

本文拟定了一种以熔融法制备样片,用X射线荧光光谱测定硅酸盐类样品中Si、Fe、Al、Tj、Mn、Ca、Mg、K、Na、P等元素的分析方法。在对不同靶材X光管和分光晶体实验对比的基础上,选择了最佳的测量条件。该法具有快速、准确,测量范围广,检测限低,价格便宜等优点。经过近百个各种类型标样或管理样品的分析对比表明,本法不仅适用于硅酸盐类岩石样品的分析,还适用于铁矿、铝土矿、碳酸盐类岩矿样品以及水泥、耐火材料等样品的分析。     

高压微波消解法测定醋酸纤维过滤器采集的微尘粒子中的砷镉钴铬铜铁锰镍铅钒锌

最新的流行病学研究表明,空气中较高浓度的悬浮细颗粒可能对人类的健康有不利的影响。根据该项研究显示,由于心脏病、慢性呼吸问题和肺功能指标恶化而导致死亡率的升高与细尘粒子有关。这些研究结果已经促使欧盟于1999年4月出台了限制空气中二氧化硫、二氧化氮、氧化氮、铅和颗粒物含量的法案(1999/30/EC),对各项指标包括对可吸入PM10颗粒的浓度提出了新的限制性指标。PM10颗粒是指可以通过预分级器分离采集的气体动力学直径小于10μm的细颗粒。目前研究的兴趣重点逐步偏向PM2.5这些更细微颗粒物,PM2.5这种颗粒物对健康有明显的不利影响。在欧盟指令2008/50/EC中,对PM10和PM2.5都提     

Isotopic systematics of He,Ar, S,Cu, Ni,Re, Os,Pb, U,Sm, Nd,Rb, Sr,Lu, and Hf in the rocks and ores of the Norilsk deposits

This paper reports the first results of a study of 11 isotope systems (³He/⁴He, ⁴⁰Ar/³⁶Ar, ³⁴S/³²S, ⁶⁵Cu/⁶³Cu, ⁶²Ni/⁶⁰Ni, ⁸⁷Sr/⁸⁶Sr, ¹⁴³Nd/¹⁴⁴Nd, ^206–208Pb/²⁰⁴Pb, Hf–Nd, U–Pb, and Re–Os) in the rocks and ores of the Cu–Ni–PGE deposits of the Norilsk ore district. Almost all the results were obtained at the Center of Isotopic Research of the Karpinskii All-Russia Research Institute of Geology. The use of a number of independent genetic isotopic signatures and comprehensive isotopic knowledge provided a methodic basis for the interpretation of approximately 5000 isotopic analyses of various elements. The presence of materials from two sources, crust and mantle, was detected in the composition of the rocks and ores. The contribution of the crustal source is especially significant in the paleofluids (gas–liquid microinclusions) of the ore-forming medium. Crustal solutions were probably a transport medium during ore formation. Air argon is dominant in the ores, which indicates a connection between the paleofluids and the atmosphere. This suggests intense groundwater circulation during the crystallization of ore minerals. The age of the rocks and ores of the Norilsk deposits was determined. The stage of orebody formation is restricted to a narrow age interval of 250 ± 10 Ma. An isotopic criterion was proposed for the ore-bearing potential of mafic intrusions in the Norilsk–Taimyr region. It includes several interrelated isotopic ratios of various elements: He, Ar, S, and others.     

Viscous, cohesive, non-Newtonian, depositing, radial slurry flow

Mining induced subsidence can significantly affect mining costs where major surface facilities and natural environment need to be protected. Overburden grout injection is a technology used to control coal mine subsidence by injecting the mine waste material extracted from the coal back into the inter-burden rock during longwall mining. The flowing slurry is here categorised as a nonlinear viscous cohesive (Bingham plastic) fluid. During longwall mining the grout slurry is pumped into the separated beds of the rock mass through a central vertical borehole, which is drilled deep into the inter-burden rock strata above the coal seam. However, a blockage can occur in the injection system when the slurry velocity falls below a certain critical threshold velocity, indicating a material phase change from cohesive-viscous to cohesive-frictional. In situ field injection tests through boreholes have been simulated at a smaller scale at the CSIRO laboratory in Brisbane by pumping the slurry through a radial disk (gap = 4 mm) from its centre. Laboratory experiments indicate a general, nonlinear, cohesive, viscous, frictional model for shear behaviour of the slurry, in which the material shear parameters are functions of the disk radial distance. Complete dimensional and dimensionless analytical solutions have been developed based on an approach related to Bingham–Herschel–Bulkley fluid mechanics. The derived formulae include relations for minimum pump pressure, local pressure and pressure gradient, wall shear stress, volume rate, velocity and velocity gradient. The theoretical results match the experimental measurements. The experiments covered slurries with maximum particle sizes of 0.5 to 2 mm with about 50% being larger than 100 µm. The viscosities at the various solids concentrations were measured with a standard torsion viscometer. This study differs from the previous research in several distinct aspects, namely, consideration of the variable shear parameters rather than fixed values, inclusion of total nonlinear behaviour, and implementation of a friction function to mimic behaviour of the deposited and consolidating stiff slurry, which can cause a significant pressure rise as a result of the increased shear resistance.     

硅酸盐中铁、锰、钛、钙、钾、磷、硅、铝、镁、钠、锶、铷、钡的X-射线荧光光谱定量测定

本文介绍样品经四硼酸锂熔融制成玻璃小饼。采用Lachance模式和理论a系数来校正元素间的效应,由3080E型X-射线荧光谱仪和DF-350B数据处理系统完成硅酸盐中十三个项目的测定。     

岩石密度和超高压岩石折返速率

在常温常压条件下对中国大陆科学钻CCSD主孔100-3000米岩心样品进行了密度测量,建立了密度连续剖面,并界定了不同超高压岩石的密度值。通过对比高温高压物性实验资料,岩石密度随着退变程度增强而降低,榴辉岩密度变化序列为3.52g/cm3→3.49g/cm3→3.07g/cm3→2.93g/cm3。超高压长英质岩石密度变化序列为3.00g/cm→2.80g/cm3→2.65g/cm3。上述实验资料是讨论不同折返阶段岩石所受浮力的基础,为研究折返速率大小提供了基本参数。本文通过折返板块运动平衡时,上浮力与粘滞力平衡这一关系式,定量研究了大陆俯冲板块的折返速率,认为密度差产生上浮力从而引起折返,温度对板块折返速率的影响最为显著;密度差大小、折返角度、折返板块大小对折返速率也有直接的影响。定量模拟分析表明,在温度高于850℃时,板块的折返速率可以超过100mm/a;当温度降至700℃时,折返速率则低于1.5mm/a。作者认为在折返早期,温度较高,板块快速折返至60-70km榴辉岩相深度;随着传导散热,温度降低,板块以较慢的速率折返至中下地壳。折返速率的估算表明,浮力是板块折返第一阶段(从>100km深部折返至<40km的中下地壳)的主要驱动力。     

Bellechester,Minnesota, USA,lagoon collapses

Bellechester, Minnesota, is a small community of approximately 155 residents located on the county line between Goodhue and Wabasha counties in southeast Minnesota's karst region. Bellechester is served by a 21-year-old wastewater treatment facility (WWTF) consisting of three waste-stabilization ponds. On 28 April 1992 six sinkholes were discovered to have drained cell 2 of the WWTF resulting in the loss of approximately 8.7×10⁶ 1 of partially treated effluent and about 600 m³ of soil into previously undetected subsurface voids of unknown dimensions. In the week following the collapse, approximately 200 water wells located within a 5-km radius of the WWTF were sampled in an after-the-fact, emergency sampling program. Twelve samples with elevated fecal coliform levels, 18 samples with nitrate-nitrogen greater than the 10 mg/1 standard, and no samples with elevated chlorides were found. However, the elevated levels could not be unambiguously attributed to the WWTF collapse. This is the third WWTF to fail by sinkhole collapse in southeast Minnesota since 1974. All three collapsed lagoons have been located in similar geomorphic and stratigraphic settings. However, at least two lagoons have collapsed in the adjacent area in northeast Iowa, and these lagoons are located at different stratigraphic positions. Twenty-two WWTFs constructed in southeast Minnesota's karst region in the last 25 years have been identified as subject to potential sinkhole collapse. An unknown but significant number of manure storage lagoons, flood control structures, etc., have also been constructed in the karst region and are at risk. Public agencies are beginning to develop plans to deal with the risk associated with existing and future waste lagoons in this environment. The critical hydrogeologic parameters that can be used to prioritize the risk of collapse at existing facilities include: (1) the lithology of the first bedrock beneath each lagoon, (2) the thickness of surficial materials between the lagoon and the bedrock surface, (3) the presence and construction of liners (seepage rate), and (4) the proximity to existing sinkholes.     

Mercury,arsenic, antimony,and selenium contents of sediment from the Kuskokwim River,Bethel, Alaska,USA

The Kuskokwim River at Bethel, Alaska, drains a major mercury-antimony metallogenic province in its upper reaches and tributaries. Bethel (population 4000) is situated on the Kuskokwim floodplain and also draws its water supply from wells located in river-deposited sediment. A boring through overbank and floodplain sediment has provided material to establish a baseline datum for sediment-hosted heavy metals. Mercury (total), arsenic, antimony, and selenium contents were determined; aluminum was also determined and used as normalizing factor. The contents of the heavy metals were relatively constant with depth and do not reflect any potential enrichment from upstream contaminant sources.     

滇东南花岗岩与锡、银、铜、铅、锌多金属矿床的成因关系

滇东南锡、银、铅、锌多金属矿床主要分布在个旧、白牛厂、都龙3个矿区,而滇东南较大的3个花岗岩体又分别出露在3个矿区或附近.花岗岩体均形成于燕山晚期,岩石化学、矿物成分相似,富含锡、银、铅、锌、钨、铜等成矿元素.矿床主金属元素组合与岩体之间的距离由远而近出现由锡、钨、(铍、铌、钽)→锡、钨、(铁)、铜、铟→锡、铅、锌、银、铟、(锑)有规律的变化.花岗岩浆是成矿物质来源和成矿热源.岩浆侵入初期使上覆地层隆起产生背斜(凹陷部位成向斜);同时使地层产生一系列裂隙、压性断层或层间断裂;岩浆侵入晚期,这些断层再次活动,表现为张性,岩浆产生的含矿热液沿由其活动所造成的断裂迁移、充填、交代、沉淀而形成矿床.