Mechanical Characteristics of Light-Weighted Soils Using Dredged Materials

This study investigates the mechanical characteristics of light-weighted soils (LWS) consisting of expanded polystyrene (EPS), dredged clays, and cement through both unconfined and triaxial compression tests. The mechanical characteristics of the compressive strength of LWS are analyzed with varying initial water contents of dredged clays, EPS ratio, cement ratio, and curing pressure. In the triaxial compression test, it is found that the compressive strength of LWS associated with EPS is independent on the effective confining pressure. When both EPS ratio is less than 2% and cement ratio is more than 2%, the compressive strength rapidly decreases after the ultimate value. This signifies that the compressive strength-strain behavior is quite similar to that of the cemented soil. The ground improved by LWS has the compressive strength of 200 kPa associated with the optimized EPS ratio of 3–4% and initial water content of 165–175%. The ultimate compressive strength under both triaxial and unconfined compression tests is almost constant for a cement ratio of up to 2%.     

Stress-Strain Behavior of Light-Weighted Soils

Unconfined and triaxial compression tests were carried out to examine the behavior of light-weighted soils (LWS) consisting of expanded polystyrene (EPS), dredged soils, and cement with respect to initial water content. The stress-strain behavior of LWS are analyzed with varying initial water content and silt contents of dredged soils, cement ratio, and confined stress. As initial water contents increase, the compressibility index increases and the preconsolidation pressure was vice versa. As initial water contents increase, the slope of stress-strain curve in elastic zone increases and strain rate at failure decreases and the strain rate at failure was not changed by the being of foams. As initial water contents increase, a compressive strength of LWS decreases. The decrement ratio of compressive strength of LWS with foams increases as cement content increases and initial water contents decreases. The compressive strength increases as silt contents increases.     

A simple experimental method to regain the mechanical behavior of naturally structured marine clays

Quantitative laboratory studies on the structural behavior of natural intact marine clays require a large number of identical natural samples leading to an expensive and challenging task. This study proposes a simple method to reconstruct an artificial structured marine clay as the state of its natural intact clay at both macro and micro levels. For this purpose, the Shanghai marine clay is selected and mixed with low cement contents (1–6%). The clay-cement slurry is mixed in a container with the ice-covered sides at a low temperature about 0 ± 2 °C to postpone the hydration reactions until consolidation began. The purpose of adding cement is to generate the inter-particle bonding and structure in reconstituted samples. Initially, the reconstituted samples are consolidated under the in situ stress of 98 kPa and then under the pre-consolidation pressure of 50 kPa. Mechanical characteristics such as compression index, yield stress, unconfined compression strength, shear strength ratio, and the stress paths from triaxial tests are compared with natural intact clay accordingly. Scanning electron microscope and mercury intrusion porosimetry analyses are also performed to analyze the microstructure of clays for comparison. Furthermore, the proposed method is also examined by using natural intact marine clays of different locations and characteristics.     

Laboratory study on cement admixed marine silt bricks

For the purpose of efficient utilization of sediments dredged from harbor, a new method was proposed in this study. Marine silt bricks were made by mixing sediments with cement and gypsum, placing it in a cubic mold with 240 mm in length, 115 mm in width, and 53 mm in height, and curing for certain days. To investigate the effects of cement and initial water content of soil on the mechanical behavior of marine silt bricks, unconfined compressive and flexural strength tests were carried out. Given the same curing time and cement content, the higher the initial water content, the lower the compressive and flexural strength. After 60 days of curing, the compressive strength of marine silt bricks with cement content = 20% and water content = LL (liquid limit) reached approximately 5 MPa. The flexural strength was relatively low. The flexural strength of marine silt bricks with 20% cement and water content = LL was around 1.5 MPa. The compressive and flexural strength decreased with the increase of water/cement ratio. As for the curing time, longer curing time had a positive impact on the compressive strength. The ratio of flexural to compressive strength varied slightly in the range of 0.4–0.5.     

Strength evaluation of marine clay stabilized by cementitious binder

Abstract

Evaluation of the strength of cement-treated clay with a broad range of mix ratios and curing periods was conducted using unconfined compression tests (UCTs). The influence of cement content, total water content, and curing period on the unconfined compressive strength of cemented clay are investigated. It is found that, at constant total water content, higher cement content results in higher unconfined compressive strength, while the total water content has an opposite effect. A power function can be used to correlate the unconfined compressive strength with the cement content or the total water content. For a fixed mix ratio, the unconfined compressive strength of cement-stabilized clay increases with the curing period, the effect of which can be characterized by a semi-log formula. Also, a strength-prediction model that considers both mix ratios and curing periods for cement-admixed marine clay is developed and validated; the model can capture the effect of clay type by considering the plastic index of untreated soils. It is also proved that the proposed framework for strength development is also applicable for other cement types.     

Strength Sensitivity of Marine Ariake Clays

Natural Ariake clays are characterized by high sensitivity. In this study, the mechanism and the factors controlling undrained shear strengths of both undisturbed and remolded Ariake clays are discussed. A series of unconfined compressive tests were performed on undisturbed samples of natural Ariake clays. The remolded undrained shear strength is predicted using a quantitative expression derived from extensive data of remolded undrained shear strength for a number of soils compiled from resources in the literature. The sensitivity of natural Ariake clays derived from the ratio of half of unconfined compressive strength for undisturbed samples to remolded undrained shear strength is found to be affected by both natural water content and normalized water content that is defined as the ratio of natural water content to liquid limit. The smaller the natural water content, the higher the sensitivity is at the same normalized water content. At the same natural water content, the larger the normalized water content, the higher the sensitivity is.     

Strength Sensitivity of Marine Ariake Clays

ABSTRACT

Natural Ariake clays are characterized by high sensitivity. In this study, the mechanism and the factors controlling undrained shear strengths of both undisturbed and remolded Ariake clays are discussed. A series of unconfined compressive tests were performed on undisturbed samples of natural Ariake clays. The remolded undrained shear strength is predicted using a quantitative expression derived from extensive data of remolded undrained shear strength for a number of soils compiled from resources in the literature. The sensitivity of natural Ariake clays derived from the ratio of half of unconfined compressive strength for undisturbed samples to remolded undrained shear strength is found to be affected by both natural water content and normalized water content that is defined as the ratio of natural water content to liquid limit. The smaller the natural water content, the higher the sensitivity is at the same normalized water content. At the same natural water content, the larger the normalized water content, the higher the sensitivity is.     

Enhancing the mechanical properties of marine clay using cement solidification

Abstract

The use of soft clay and dredged marine clays as the construction material is challenging. This is because the high water content, high compressibility and low permeability of the clay causing the instability of ground and structure. This detrimental effect of soft clay can be improved by the cement solidification process, which is relatively cheap and efficient. This paper mainly focuses on the study of improvement on the mechanical behavior of cement mixed marine clay. The soil is reconstituted by using ordinary Portland cement of 5%, 10%, 15% and 20% by its mass. The study reveals that cementation of clay significantly improves the peak and residual strength of soil. Similarly, the primary yield stress of the soil is also improved from 16 to 275?kPa as cement content increases from 5% to 20%, respectively. By using statistical tools, the relationships between various parameters are established, which are very important to define the mechanical behavior of the clay. This study reveals that the yield surface of the solidified marine clay is not a smooth elliptical surface. Rather it is composed of two linear surfaces followed by a log-linear surface which can be modeled by using simple parameters obtained from triaxial tests.     

Equivalent void ratio controlling the mechanical properties of cementitious material-clay mixtures with high water content

Abstract

This research develops a parameter defined as the equivalent void ratio, e?_st, which is able to accurately describe the dependence of the mechanical properties of cementitious material-clay mixtures on the influencing parameters, i.e., the mixing proportion, curing time, and initial state of the mixture, for different types of cementitious materials based on the results of unconfined compression, oedometer, and triaxial tests. Besides Portland cement, cementitious materials, such as fly ash and rice husk ash, are considered supplementary cement with different levels of efficiency. This equivalent cementitious material concept is then adapted for parameter development in conjunction with the effective void ratio proposed from our previous study. The developed single parameter, e?_st, can assess the mechanical properties of cementitious material-clay mixtures with different types of cementitious materials and under different test conditions.     

Consolidation and creep behaviors of two typical marine clays in China

This paper presents an experimental investigation into the deformation characteristics of two typical marine clays obtained from Dalian and Shanghai, respectively, in China. Three kinds of laboratory tests, i.e. conventional oedometer tests, one-dimensional and triaxial creep tests were carried out. The results obtained from consolidation tests demonstrate linear v e ？ log？ relationships for Shanghai clay at normally consolidated state, while partly or even global non-linearrelationships for Dalian clay. The compression index c C for both clays follows the correlation of Cc=0.009（WL-10）where WL is the liquid limit of soil. The relationship between v log Kv （ Kv is the hydraulic conductivity of soil） and voidratio e is generally linear and the hydraulic conductivity change index kv C can be described by their initial void ratio forboth clays. The secondary compressibility of Dalian clay lies in medium to high range and is higher than that of Shanghaiclay which lies in the range of low to medium. Furthermore, based on drained triaxial creep tests, the stress-strain-timerelationships following Mesri＇s creep equation have been developed for Dalian and Shanghai clays which can predict thelong-term deformation of both clays reasonably well.     

Mechanical and Germination Characteristics of Stabilized Organic Soils

High-organic-content dredged soils are known to have inferior mechanical characteristics because they are highly compressible and have low shear strength. To recycle dredged soil with a high organic content as a top soil this study describes an investigation of the mechanical properties and germination characteristics of stabilized organic soils using unconfined compression tests, pH tests, and seed germination tests. Several mixtures with organic contents in the range 0–30% by mass and binder contents in the range 5–15% were prepared to evaluate the effects of the organic content on the mechanical and germination characteristics of the stabilized soils. The results show that an increase in the organic content leads to a decrease in the strength and pH of the stabilized organic soil, which are favorable conditions for germination. The germination rate increased significantly with the increasing organic content, and the plant growth rate also increased. The addition of a binder into the mixtures increased the strength of the soil; however, it also increased the pH and decreased the rate of seed germination and plant growth.     

Primary yielding locus of cement-stabilized marine clay and its applications

ABSTRACT

Strength and stiffness properties of materials are widely studied and used in civil engineering practice. However, most studies are based on unconfined conditions, which are different from real status of soil. This study investigated the primary yielding and yield locus for cement-stabilized marine clay. In this study, two types of cement-stabilized soils were studied through isotropic compression, triaxial drained shearing, unconfined compression, and bender element testing. Specimens with 20–50% of cement content and 7–90 days of curing period were used for the tests. Stress–strain behavior and primary yielding were evaluated, followed by construction of the primary yield locus. The characteristics of the primary yield locus and its development with curing time then were studied. The results showed that the properties of the primary yield locus were dependent on the type of stabilized soil, but were independent of the cement content and curing period. Thus, the approach provides a way to estimate the primary yield stress and drained stress path before primary yielding for cement-stabilized soil under confined condition. An empirical function was used to fit the primary yield locus. The primary isotropic yield stress was correlated to unconfined compressive strength or maximum shear modulus. Three indirect methods were proposed to predict the primary yield stress for cement-stabilized marine clay. The results showed that the primary yield stress can be estimated with reasonable accuracy.     

Laboratory and Field Observations for Golden Horn Marine Clay

Istanbul, the largest city in Turkey and one of the major metropolitan areas in the world, cleaned one of its environmentally polluted areas—Golden Horn—by dredging 5 million m³ of the bottom sediments and pumping the resulting sludge to a storage area behind a dam built at an abandoned rock quarry site in Alibey district. The reclamation of the land that formed over the storage area of Golden Horn dredged material is socially and economically very desirable. In this paper, results from experimental studies that are focused on determining the shear strength behavior of the dredge material and undisturbed soil are presented. Slurry consolidometer test, large model tests and small model tests are used to consolidate the dredged soil samples from Halic to simulate the natural consolidation behavior of these soils. Shear strength parameters are determined by laboratory vane tests; unconfined compression tests; undrained-unconsolidated (UU) and consolidated-undrained (CU) triaxial tests on samples that are obtained through in situ undisturbed samples and laboratory model tank and slurry consolidation. Moreover, the effects of fly ash and lime additives on the undrained shear strength were determined by mixing the materials with the dredged clay from Golden Horn during the model experiments conducted in the laboratory. Based on these findings, equations are proposed that govern the relationships between undrained shear strength and water content value.     

On Physical and Mechanical Behavior of Natural Marine Intermediate Deposits

Coastal structures may be built on natural sedimentary intermediate grounds, which mainly consist of silty soils and fine sandy soils. In this study, extensive field and laboratory tests were performed on the nattwal marine intermediate deposits to demonstrate the difference in behavior between natural marine clayey soils and natural marine intermediate deposits. The natural intermediate deposits have almost the same miles of natural water content to liquid limit as those of the soft natural marine clays, but the former have much higher in-situ strength and sensitivity than the latter. The research results indicate that grain size distributions of soils affect significantly tip resistance obtained in field cone penetration tests. The mechanical parameters of natural marine intermediate deposits are also significantly affected by sample disturbance due to their high sensitivity and relatively large permeability. Unconfined compression shear tests largely underestimate the strength of natural marine intermediate soils. The triaxial consohdated compression shear tests with simulated insitu confined pressure give results much better than those of uncomfined compression shear tests.     

Mechanical Behavior of Light-Weight Soil Under Consolidated Drained Shear Condition

To reveal the influence of material composition on mechanical properties of light-weight soil, stress-strain -volumetric strain characteristics and Poisson's ratio of mixed soil were researched by consolidated drained shear tests. The results show that light-weight soil is a kind of structural soil, so its mechanical properties are affected by mixed ratio and confining pressure, and mixed soil possesses structural yield stress. When confining pressure is less than the structural yield stress, strain softening occurs; when confining pressure is more than the structural yield stress, strain hardening is observed. There are two kinds of volume change behavior: shear contraction and shear dilatancy. Shear dilatancy usually leads to strain softening, but there isn't an assured causal relationship between them. Poisson's ratio of mixed soil is a variational state parameter with the change of stress state, it decreases with increased confining pressure, and it increases with increased stress level. When axial strain is near 5%, Poisson’ ratio is gradually close to a steady value. The main range of Poisson's ratio is 0.25～0.50 when confining pressure changes from 50 to 300 kPa. When unconfined compressive strength of mixed soil is less than 328 kPa, its stress-strain-volumetric strain characteristics can be predicted very well by Duncan-Chang model (E-B model). However, when the range of unconfined compressive strength is [328 kPa, 566 kPa], the model can't predict stress-strain characteristics accurately when confining pressure is under 200 kPa, and it also can't predict the strong shear dilatancy phenomenon of mixed soil under low confining pressure.     

Engineering behaviour of MICP treated marine clays

Abstract

In the present scenario, with much focus on sustainable development worldwide, Microbially Induced Calcite Precipitation (MICP) is a promising biological soil improvement technology. However, only very limited research is reported on the effectiveness of this technique in marine clays. This paper presents the salient features of an experimental study conducted on two typical marine clays stabilised by MICP. Effectiveness of the technique was evaluated through a series of one-dimensional consolidation tests, unconfined compression tests, and index property determinations. It is found that biostimulation approach is not effective in marine clay; bio-augmentation is needed for soil improvement. Bio-augmentation results in the reduction of liquid limit and plasticity index to about 29% and 47%, respectively for the marine clays. A comparable improvement in volume change behaviour is also observed. There is a marked increase in undrained shear strength, upto about 148%, of MICP treated marine clays at toughness limit water content. Curing is also found to have a significant role in soil improvement. The observed transition in the nature of the tested marine clays from that of fat clay to elastic silt suggests the potential of the proposed approach. An empirical equation is also proposed to predict compression index of MICP treated marine clays.     

Strength characteristics of cemented sand–bentonite mixtures with fiber and metakaolin additions

Compacted sand–bentonite mixtures have been used as a good alternative hydraulic barrier material to compacted clays. This study presents the results of a laboratory investigation on the strength characteristics of cement-stabilized sand–bentonite (CSB) mixtures and the effects of adding small amounts of fibers and metakaolin to the mixture material for strength improvement. The strength characteristics of the mixture materials were examined using unconfined compressive strength (UCS) tests and splitting tensile strength (STS) tests, with emphasis on evaluating the effects of different proportions of bentonite, fibers, and metakaolin within the CSB mixtures with a constant value of cement content. The test results indicated that the maximum improvements in UCS and STS were all attained in the CSB mixture with 10% bentonite content, and the inclusion of fibers and metakaolin of 1% each within the same CSB mixture led to an increase in UCS of about 40 and 70%, respectively. The addition of fibers also increased the ductility of the mixture material and was more effective for the improvement of tensile strength compared to that of metakaolin. The contribution of metakaolin to early-age strength (i.e., 3 and 7 days) of CSB mixture was found to be small due to the relatively low cement content in the mixture.     

Effect of Sample Disturbance on Unconfined Compression Strength of Natural Marine Clays

1 .IntroductionCoastalstructuresoftenencountersettlementandstabilityproblemsofsoftmarinefoundation (Liuetal.,1 999;Zhouetal.,2 0 0 0 ;Liuetal.,2 0 0 3) .Manyresearchershaveillustratedthatnaturalmarineclaysaregenerallysubjectedtotheeffectsofsoilstructureduringtheirdepositionalandpost depositionalprocesses (Zhangetal.,1 995;Hongetal.,2 0 0 3a ;2 0 0 3b) .Thesoilstructureofnat uralmarineclaysiseasilydamagedduringsamplingandhandlingbecausenaturalmarineclaysgeneral lyhavehighwatercontentandlowsti…     

Parameter studies of sediments in the Storegga Slide region

Based on classification tests, oedometer tests, fall-cone tests and triaxial tests, physical and mechanical properties of sediments in the Storegga Slide region were analysed to assess parameter interrelationships. The data show good relationships between a number of physical and mechanical parameters. Goodness of fit between compression index and various physical parameters can be improved by multiple regression analysis. The interclay void ratio and liquidity index correlate well with the undrained shear strength of clay. Sediments with higher water content, liquid limit, activity, interclay void ratio, plasticity index and liquidity index showed higher compression index and/or lower undrained shear strength. Some relationships between parameters were tested by using data from two other sites south of the Storegga Slide. A better understanding of properties of sediments in regions such as that of the Storegga Slide can be obtained through this approach.     

海洋粉质粘土在波浪荷载作用后的不排水抗剪强度衰化特性

通过对南海重塑粉质粘土土样的大量动三轴试验结果分析,得到此种土在波浪荷载作用后不捧水抗剪强度衰化同动载作用引起的动应变幅及平均累积孔压之间的相互关系和预估公式;并通过与超固结土样的静三轴剪切试验结果的比较,发现动、静三轴两种试验结果具有很好的吻合关系。建议可用超固结土样的静三轴剪切试验同时结合部分动三轴试验来预估土样在波浪荷载作用后不排水抗剪强度衰化与平均累积孔压之间的关系。