Landslide susceptibility mapping using analytic hierarchy process and information value methods along a highway road section in Constantine,Algeria

This research work deals with the landslide susceptibility assessment using Analytic hierarchy process (AHP) and information value (IV) methods along a highway road section in Constantine region, NE Algeria. The landslide inventory map which has a total of 29 single landslide locations was created based on historical information, aerial photo interpretation, remote sensing images, and extensive field surveys. The different landslide influencing geoenvironmental factors considered for this study are lithology, slope gradient, slope aspect, distance from faults, land use, distance from streams, and geotechnical parameters. A thematic layer map is generated for every geoenvironmental factor using Geographic Information System (GIS); the lithological units and the distance from faults maps were extracted from the geological database of the region. The slope gradient, slope aspect, and distance from streams were calculated from the Digital Elevation Model (DEM). Contemporary land use map was derived from satellite images and field study. Concerning the geotechnical parameters maps, they were determined making use of the geotechnical data from laboratory tests. The analysis of the relationships between the landslide-related factors and the landslide events was then carried out in GIS environment. The AUC plot showed that the susceptibility maps had a success rate of 77 and 66% for IV and AHP models, respectively. For that purpose, the IV model is better in predicting the occurrence of landslides than AHP one. Therefore, the information value method could be used as a landslide susceptibility mapping zonation method along other sections of the A1 highway.     

Geometric and kinematic characterization of landslides affecting urban areas: the Lungro case study (Calabria,Southern Italy)

The geometric and kinematic characterization of landslides affecting urban areas is a challenging goal that is routinely pursued via geological/geomorphological method and monitoring of ground displacements achieved by geotechnical and, more recently, advanced differential interferometric synthetic aperture radar (A-DInSAR) data. Although the integration of all the above-mentioned methods should be planned a priori to be more effective, datasets resulting from the independent use of these different methods are commonly available, thus making crucial the need for their standardized a posteriori integration. In this regard, the present paper aims to provide a contribution by introducing a procedure that, taking into account the specific limits of geological/geomorphological analyses and deep/surface ground displacement monitoring via geotechnical and A-DInSAR data, allows the a posteriori integration of the results by exploiting their complementarity for landslide characterization. The approach was tested in the urban area of Lungro village (Calabria region, southern Italy), which is characterized by complex geological/geomorphological settings, widespread landslides and peculiar urban fabric. In spite of the different level of information preliminarily available for each landslide as result of the independent use of the three methods, the implementation of the proposed procedure allowed a better understanding and typifying of the geometry and kinematics of 50 landslides. This provided part of the essential background for geotechnical landslide models to be used for slope stability analysis within landslide risk mitigation strategies.     

Pre-conditioning factors and susceptibility assessments of Wenchuan earthquake landslide at the Zhouqu segment of Bailongjiang basin, China

In this study, we present a landslide susceptibility assessment carried out after the devastating 2008 Wenchuan earthquake. For the Zhouqu segment in the Bailongjiang basin in north-western China landslide susceptibility was computed by a logistic regression method. This region has been experiencing landslides for a long time, and numerous additional slope failures were triggered by the 2008 Wenchuan earthquake. The data used for this study consists of slope failures attributed to the 2008 earthquake, the 878 post Wenchuan earthquake landslides and collapses inventory build up by combination the field investigation, monoscopic manual interpretation, image classification and texture analysis using SPOT 5 and ALOS remote-sensing image data. All data derived from remote sensing images are validated during field investigations. The landslide pre-disposing factor database was constructed. A digital elevation model (DEM) with a 30 × 30 m resolution, orthophotos, geological and land-use maps and information on peak ground acceleration data from the 2008 earthquake is used. The statistical analysis of the relation between Wencuan earthquake-triggered landslides and pre-disposing factors show the great influence of lithological and topographical conditions for earthquake-triggered slope failures. The quality of susceptibility mapping was validated by splitting the study area into a training and validation set. The prediction capability analysis showed that the landslide susceptibility map could be used for land planning as well as emergency planning by local authorities in this region.     

Susceptibility assessments of the Wenchuan earthquake-triggered landslides in Longnan using logistic regression

In this study a Wenchuan earthquake-induced landslide susceptibility assessment was carried out in the Longnan area in northwestern China using a GIS-based logistic regression model. This region has frequently been affected by landslides in the past, and was intensively affected by the 5.12 Wenchuan earthquake which received considerable international attention. The data used for this study consist of the landslides triggered by the Wenchuan earthquake and a landslide pre-disposing factor database. Information regarding the landslide causative factors came from additional data sources, such as a digital elevation model (DEM) with a 30 × 30 m² resolution, orthophotos, geological and land-use maps, precipitation records, and information on peak ground acceleration data from the 2008 earthquake. The statistical analysis of the relationship between the Wenchuan earthquake-triggered landslides and pre-disposing factors showed the great influence of lithological and topographical conditions on slope failures. The quality of susceptibility mapping was validated by splitting the study area into training and validation sections. The prediction capability analysis demonstrated that the landslide susceptibility map could be used for land planning as well as emergency planning by local authorities.     

Different ways of landslide geometry interpretation in a process of statistical landslide susceptibility and hazard assessment: Horná Súča (western Slovakia) case study

The article draws a comparison between different ways of landslide geometry interpretation in the scope of the statistical landslide hazard and risk assessment processing. The landslides are included as a major input variable, which are compared with all of the input parametric factors. Based on the above comparison the input data are classified and the final map of landslide susceptibility is constructed. Methodology of multivariate conditional analysis has been used for the construction of final maps. Unique condition units was developed by combination of geological map (lithological units) and slope angle map. Lithological units were derived from geological map and subsequently reclassified into 22 classes. Slope angle map was calculated from digital elevation model (contour map at a scale 1:10,000) and reclassified into nine classes. As a case study, a wide area of Horná Súča (western Slovakia) strongly affected by landsliding (predominantly made of Flysch) has been chosen. Spatial data in the form of parametric maps, as well as final statistical data set were processed in GIS GRASS environment. Four different approaches are used for landslides interpretation: (1) area of landslide body including accumulation zone, (2) area of depletion zone, (3) lines of elongated main scarps, (4) lines of main scarp upper edge. For each approach, a zoning map of landslide susceptibility was compiled and these were compared with each other. Depending on the interpretation approach, the final susceptibility zones are markedly different (in tens of percent).     

Ground deformation monitoring by using the Permanent Scatterers Technique: The example of the Oltrepo Pavese (Lombardia, Italy)

The applicability of the Permanent Scatterers Synthetic Aperture Radar Interferometry (PSInSAR) technique for detecting and monitoring ground displacements was tested in the Oltrepo Pavese territory (Northern Italy, southern Lombardia), which could be representative of similar geological contexts in the Italian Apennines. The study area, which extends for almost 1100 km², is characterized by a complex geological and structural setting and the presence of clay-rich sedimentary formations. These characteristics make the Oltrepo Pavese particularly prone to several geological hazards: shallow and deep landslides, subsidence and swelling/shrinkage of the clayey soils. The PSInSAR technique used in this study overcomes most of the limitations of conventional interferometric approaches by identifying, within the area of interest, a set of “radar benchmarks” (PS), where very precise displacement measurements can be carried out. More than 90,000 PS were identified by processing Synthetic Aperture Radar (SAR) images acquired from 1992 to 2001 by the European Remote Sensing satellites (ERS). The PSInSAR application at a sub-regional scale detected slow ground deformations ranging from + 5 to − 16 mm/year, and resulting from various processes (landslides, swelling/shrinkage of clay soils and water pumping). The PS displacements were analysed by collecting data obtained through geological, geomorphologic field surveys, geotechnical analysis of the soils and the information was integrated within a landslide inventory and the damaged building inventory. Despite the limited number of landslide bodies with PS (7% of the inventoried landslides), the PS data helped to revise the state of activity of several landslides. Furthermore, some previously unknown unstable slopes were detected. Two areas of uplift and two areas of subsidence were identified.     

杭州市滑坡地质灾害危险性区划与评价

基于证据权法构建滑坡地质灾害评价模型,进行杭州市滑坡地质灾害危险性区划研究。主要数据源包括1930－2009年杭州市域采集到的1 905个地质灾害个例以及杭州市地质图、土地利用数据及数字高程模型（DEM）等。利用Arcgis空间分析及信息提取功能,筛选强降水、地层岩性、坡度、坡向、坡高、河网与道路缓冲等证据因子,并运用证据权法客观确定各因子权重, 最后通过Arc-WofE扩展模块对多种优选因子的叠加,计算任意格网单元的滑坡发生概率,实现对潜在滑坡点位的空间预测。经分离样本法验证,区划准确率为88.3%,分析结果与现有滑坡的分布情况比较吻合。据此表明证据权法在多指标评价及其权重确定等方面具有普适性,值得在滑坡地质灾害危险性区划等方面推广应用。     

National-scale assessment of landslide susceptibility to rank the vulnerability to failure of rock-cut slopes along expressways in Korea

The objective of this study is to perform a preliminary national-scale assessment of the landslide susceptibility of rock-cut slopes along expressways in Korea. A geographic information system (GIS) database was compiled based on data from topographical and geological maps, and rock-cut slope data, including the locations of past landslides. Seven factors (i.e., slope height, slope length, slope gradient, upper slope gradient, lithology, distance from nearest fault, and dip direction of slope) were extracted from the GIS database to assess the relationship between each factor and landslide events. Weight of evidence (WOE), analytic hierarchy process (AHP), and fuzzy logic methods, as well as hybrid methods, were used to establish the rating of classes for each factor, weightings for the factors, and to combine multiple factor layers into landslide-susceptibility maps. A comparison of the results obtained using several different methods, based on the area under curve technique, revealed that the WOE method showed the highest accuracy of 74%. The annual cost of traffic congestion resulting from slope failures was evaluated to identify those rock-cut slopes where detailed investigations and landslide warning systems are required.     

http://www.sciencedirect.com/science/article/pii/S167498711400022X

The governing factors that influence landslide occurrences are complicated by the different soil conditions at various sites.To resolve the problem,this study focused on spatial information technology to collect data and information on geology.GIS,remote sensing and digital elevation model(DEM) were used in combination to extract the attribute values of the surface material in the vast study area of SheiPa National Park,Taiwan.The factors influencing landslides were collected and quantification values computed.The major soil component of loam and gravel in the Shei-Pa area resulted in different landslide problems.The major factors were successfully extracted from the influencing factors.Finally,the discrete rough set(DRS) classifier was used as a tool to find the threshold of each attribute contributing to landslide occurrence,based upon the knowledge database.This rule-based knowledge database provides an effective and urgent system to manage landslides.NDVI(Normalized Difference Vegetation Index),VI(Vegetation Index),elevation,and distance from the road are the four major influencing factors for landslide occurrence.The landslide hazard potential diagrams(landslide susceptibility maps) were drawn and a rational accuracy rate of landslide was calculated.This study thus offers a systematic solution to the investigation of landslide disasters.     

Landslide susceptibility mapping using rough sets and back-propagation neural networks in the Three Gorges, China

In the Three Gorges of China, there are frequent landslides, and the potential risk of landslides is tremendous. An efficient and accurate method of generating landslide susceptibility maps is very important to mitigate the loss of lives and properties caused by these landslides. This paper presents landslide susceptibility mapping on the Zigui-Badong of the Three Gorges, using rough sets and back-propagation neural networks (BPNNs). Landslide locations were obtained from a landslide inventory map, supported by field surveys. Twenty-two landslide-related factors were extracted from the 1:10,000-scale topographic maps, 1:50,000-scale geological maps, Landsat ETM + satellite images with a spatial resolution of 28.5 m, and HJ-A satellite images with a spatial resolution of 30 m. Twelve key environmental factors were selected as independent variables using the rough set and correlation coefficient analysis, including elevation, slope, profile curvature, catchment aspect, catchment height, distance from drainage, engineering rock group, distance from faults, slope structure, land cover, topographic wetness index, and normalized difference vegetation index. The initial, three-layered, and four-layered BPNN were trained and then used to map landslide susceptibility, respectively. To evaluate the models, the susceptibility maps were validated by comparing with the existing landslide locations according to the area under the curve. The four-layered BPNN outperforms the other two models with the best accuracy of 91.53 %. Approximately 91.37 % of landslides were classified as high and very high landslide-prone areas. The validation results show sufficient agreement between the obtained susceptibility maps and the existing landslide locations.     

Remote sensing and GIS-based landslide susceptibility mapping using frequency ratio and analytical hierarchy methods in Rize province (NE Turkey)

The northeast part of Turkey is prone to landslides because of the climatic conditions, as well as geologic and geomorphologic characteristics of the region. Especially, frequent landslides in the Rize province often result in significant damage to people and property. Therefore, in order to mitigate the damage from landslides and help the planners in selecting suitable locations for implementing development projects, especially in large areas, it is necessary to scientifically assess susceptible areas. In this study, the frequency ratio method and the analytical hierarchy process (AHP) were used to produce susceptibility maps. Especially, AHP gives best results because of allowing better structuring of various components, including both objective and subjective aspects and comparing them by a logical and thorough method, which involves a matrix-based pairwise comparison of the contribution of different factors for landslide. For this purpose, lithology, slope angle, slope aspect, land cover, distance to stream, drainage density, and distance to road were considered as landslide causal factors for the study area. The processing of multi-geodata sets was carried out in a raster GIS environment. Lithology was derived from the geological database and additional field studies; slope angle, slope aspect, distance to stream, distance to road and drainage density were invented from digital elevation models; land cover was produced from remote sensing imagery. In the end of study, the results of the analysis were verified using actual landslide location data. The validation results showed satisfactory agreement between the susceptibility map and the existing data on landslide locations.     

GIS-based landslide susceptibility mapping using bivariate statistical analysis in Devrek (Zonguldak-Turkey)

Devrek town with increasing population is located in a hillslope area where some landslides exist. Therefore, landslide susceptibility map of the area is required. The purpose of this study was to generate a landslide susceptibility map using a bivariate statistical index and evaluate and compare the results of the statistical analysis conducted with three different approaches in seed cell concept resulting in different data sets in Geographical Information Systems (GIS) based landslide susceptibility mapping applied to the Devrek region. The data sets are created from the seed cells of (a) crowns and flanks, (b) only crowns, and (c) only flanks of the landslides by using ten different causative parameters of the study area. To increase the data dependency of the analysis, all parameter maps are classified into equal frequency classes based directly on the percentile divisions of each corresponding seed cell data set. The resultant maps of the landslide susceptibility analysis indicate that all data sets produce fairly acceptable results. In each data set analysis, elevation, lithology, slope, aspect, and drainage density parameters are found to be the most contributing factors in landslide occurrences. The results of the three data sets are compared using Seed Cell Area Indexes (SCAI). This comparison shows that the crown data set produces the most accurate and successful landslide susceptibility map of the study area.     

Landslide susceptibility mapping using LiDAR and DMC data: a case study in the Three Gorges area, China

The objective of this study is to map landslide susceptibility in Zigui segment of the Yangtze Three Gorges area that is known as one of the most landslide-prone areas in China by using data from light detection and ranging (LiDAR) and digital mapping camera (DMC). The likelihood ratio (LR) and logistic regression model (LRM) were used in this study. The work is divided into three phases. The first phase consists of data processing and analysis. In this phase, LiDAR and DMC data and geological maps were processed, and the landslide-controlling factors were derived such as landslide density, digital elevation model (DEM), slope angle, aspect, lithology, land use and distance from drainage. Among these, the landslide inventories, land use and drainage were constructed with both LiDAR and DMC data; DEM, slope angle and aspect were constructed with LiDAR data; lithology was taken from the 1:250,000 scale geological maps. The second phase is the logistic regression analysis. In this phase, the LR was applied to find the correlation between the landslide locations and the landslide-controlling factors, whereas the LRM was used to predict the occurrence of landslides based on six factors. To calculate the coefficients of LRM, 13,290,553 pixels was used, 29.5 % of the total pixels. The logical regression coefficients of landslide-controlling factors were obtained by logical regression analysis with SPSS 17.0 software. The accuracy of the LRM was 88.8 % on the whole. The third phase is landslide susceptibility mapping and verification. The mapping result was verified using the landslide location data, and 64.4 % landslide pixels distributed in “extremely high” zone and “high” zone; in addition, verification was performed using a success rate curve. The verification result show clearly that landslide susceptibility zones were in close agreement with actual landslide areas in the field. It is also shown that the factors that were applied in this study are appropriate; lithology, elevation and distance from drainage are primary factors for the landslide susceptibility mapping in the area, while slope angle, aspect and land use are secondary.     

Mapping of hazard from rainfall-triggered landslides in developing countries: Examples from Honduras and Micronesia

Loss of life and property caused by landslides triggered by extreme rainfall events demonstrates the need for landslide-hazard assessment in developing countries where recovery from such events often exceeds the country's resources. Mapping landslide hazards in developing countries where the need for landslide-hazard mitigation is great but the resources are few is a challenging, but not intractable problem. The minimum requirements for constructing a physically based landslide-hazard map from a landslide-triggering storm, using the simple methods we discuss, are: (1) an accurate mapped landslide inventory, (2) a slope map derived from a digital elevation model (DEM) or topographic map, and (3) material strength properties of the slopes involved. Provided that the landslide distribution from a triggering event can be documented and mapped, it is often possible to glean enough topographic and geologic information from existing databases to produce a reliable map that depicts landslide hazards from an extreme event. Most areas of the world have enough topographic information to provide digital elevation models from which to construct slope maps. In the likely event that engineering properties of slope materials are not available, reasonable estimates can be made with detailed field examination by engineering geologists or geotechnical engineers. Resulting landslide hazard maps can be used as tools to guide relocation and redevelopment, or, more likely, temporary relocation efforts during severe storm events such as hurricanes/typhoons to minimize loss of life and property. We illustrate these methods in two case studies of lethal landslides in developing countries: Tegucigalpa, Honduras (during Hurricane Mitch in 1998) and the Chuuk Islands, Micronesia (during Typhoon Chata'an in 2002).     

Landslide susceptibility zonation mapping using logistic regression and its validation in Hashtchin Region,northwest of Iran

Landslide susceptibility zonation mapping assists researchers greatly to understand the spatial distribution of slope failure probability in a region. Being extremely useful in reducing landslide hazards, such maps could simply be produced using both qualitative and quantitative methods. In the present study, a multivariate statistical method called ‘logistic regression’ was used to assess landslide susceptibility in Hashtchin region, situated in west of Alborz Mountainsnorthwest of Iran. In this study, two independent variables, categorical (predictor) and continuous, were drawn on together in the model. To identify the region’s landslides use was made of aerial photographs, field studies and topographic maps. To prepare the database of factors affecting the region’s landslides and to determine landslide zones, geographic information system (GIS) was used. Using such information, landslide susceptibility modeling was accomplished. The data related to factors causing landslides were extracted as independent variables in each cell (in 50 m×50 m cells). Then, the whole data were input into the SPSS, Version 18. The prepared database was later analyzed using logistic regression, the forward stepwise method and based on maximum likelihood estimation. Regression equation was determined using obtained constants and coefficients and the landslide susceptibility of the area in grid-cells (pixels) was computed between 0 and 0.9954. The Receiver Operating Characteristic (ROC) curve was used to assess the accuracy of the logistic regression model. The predicting ability of the model was 84.1% given the area under ROC curve. Finally, the degree of success of landslide susceptibility zonation mapping was estimated to be 79%.     

5.12震源区牛眠沟暴雨滑坡泥石流预测模型

牛眠沟研究区位于2008-05-12汶川大地震线性震源的南端,受强烈地震力作用,区内山体遭受严重破坏,发生多处滑坡和泥石流灾害。根据已建立的暴雨滑坡、泥石流预测概念模型,暴雨滑坡、泥石流预测可视为判断滑坡形成的地质环境和确定触发滑坡的降雨特征。查明研究区地质环境及灾害特征,确定了产生滑坡、泥石流的必要地质环境因子,以数字滑坡技术获取这些因子数据,代入模型,即可评价研究区各处、各沟谷发生滑坡、泥石流的危险程度;与相似地质环境及气候条件进行类比,确定研究区触发滑坡、泥石流的降雨特征及降雨量阈值后,最终建立暴雨滑坡、泥石流预测模型。据此模型进行研究区暴雨滑坡、泥石流预测,实地验证表明滑坡、泥石流发生位置的准确率>90%。     

基于GIS的重庆万州区滑坡灾害危险性评价

在充分调查万州区地质环境及滑坡灾害基本特征的基础上,根据资料的有效性和可获得性,选取地表高程、坡度、地层岩性、地质构造、土地利用类型、区域交通建设及河流侵蚀冲刷7个影响滑坡发生的因素作为评价指标,采用AHP法确定各个指标权重并建立滑坡灾害危险性指数模型,通过GIS系统的空间分析功能进行栅格运算,得出研究区滑坡灾害危险性分区。采用上述指标和方法将重庆市万州区的滑坡灾害划分为极高危险区、高危险区、中危险区、低危险区和极低危险区,划分结果符合该区滑坡灾害的实际情况。     

A GIS-based landslide susceptibility evaluation using bivariate and multivariate statistical analyses

Bivariate and multivariate statistical analyses were used to predict the spatial distribution of landslides in the Cuyahoga River watershed, northeastern Ohio, U.S.A. The relationship between landslides and various instability factors contributing to their occurrence was evaluated using a Geographic Information System (GIS) based investigation. A landslide inventory map was prepared using landslide locations identified from aerial photographs, field checks, and existing literature. Instability factors such as slope angle, soil type, soil erodibility, soil liquidity index, landcover pattern, precipitation, and proximity to stream, responsible for the occurrence of landslides, were imported as raster data layers in ArcGIS, and ranked using a numerical scale corresponding to the physical conditions of the region. In order to investigate the role of each instability factor in controlling the spatial distribution of landslides, both bivariate and multivariate models were used to analyze the digital dataset. The logistic regression approach was used in the multivariate model analysis. Both models helped produce landslide susceptibility maps and the suitability of each model was evaluated by the area under the curve method, and by comparing the maps with the known landslide locations. The multivariate logistic regression model was found to be the better model in predicting landslide susceptibility of this area. The logistic regression model produced a landslide susceptibility map at a scale of 1:24,000 that classified susceptibility into four categories: low, moderate, high, and very high. The results also indicated that slope angle, proximity to stream, soil erodibility, and soil type were statistically significant in controlling the slope movement.     

GIS-based rare events logistic regression for landslide-susceptibility mapping of Lianyungang,China

Landslides have had a huge effect on human life, the environment and local economic development, and therefore they need to be well understood. In this study, we presented an approach for the analysis and modeling of landslide data using rare events logistic regression and applied the approach to an area in Lianyungang, China. Digital orthophotomaps, digital elevation models of the region, geological maps and different GIS layers including settlement, road net and rivers were collected and applied in the analysis. Landslides were identified by monoscopic manual interpretation and validated during the field investigation. To validate the quality of mapping, the data from the study area were divided into a training set and validation set. The result map showed that 4.26% of the study area was identified as having very high susceptibility to landslides, whereas the others were classified as having very low susceptibility (47.2%), low susceptibility (22.21%), medium susceptibility (14.39%) and high susceptibility (11.93%). The quality of the landslide-susceptibility map produced in this paper was validated, and it can be used for planning protective and mitigation measures. The landslide-susceptibility map is a fundamental part of the Lianyungang city landslide risk assessment.