非饱和土的水力和力学特性及其弹塑性描述

简单回顾了非饱和土本构模型研究的发展历程,总结了近几年非饱和土弹塑性本构模型最新研究成果,重点介绍了能统一模拟非饱和土水力性状和力学性状耦合的弹塑性本构模型。通过对建立模型过程中的几个核心问题讨论,较详细地说明该类模型的结构、性能以及相关问题。非饱和土水力性状的滞回性用假定存在饱和度弹性区间的弹塑性过程来模拟;该类耦合模型不仅考虑了吸力对非饱和土水力性状和力学性状的影响,还考虑了饱和度对应力-应变关系和强度的影响以及土体变形对土-水特征曲线的影响。用同一套模型参数,耦合模型可统一预测在吸力控制或含水率控制下沿各种应力路径下非饱和土的水力-力学特性,并简单介绍了膨胀性非饱和土的弹塑性本构模型以及耦合模型在有限元数值计算中的应用。     

非饱和土三轴压缩应力路径试验的数值模拟研究

应力路径对土的强度和变形性质具有重要影响。相对于饱和土而言,控制吸力条件下的非饱和土三轴压缩状态的应力路径研究更加复杂。随着非饱和土本构理论的不断发展,理论和试验研究结果表明,非饱和土弹塑性本构模型可以用来近似地描述非饱和土的强度和变形性质。因而,运用非饱和土弹塑性本构模型对控制吸力条件下的3种非饱和土三轴压缩应力路径试验进行数值模拟是一种有效的理论研究手段。采用Barcelona模型能够对此类试验进行较好的数值模拟,其研究结果表明,在控制吸力条件的三轴压缩状态下应力路径对非饱和土的强度和变形性质具有重要影响。     

饱和度对非饱和土力学性质的影响

现在被广泛公认的由Fredlund提出的非饱和土力学的双参数理论,即净应力和吸力为非饱和土的应力状态量,不能直接考虑饱和度或含水率对非饱和土的应力-应变关系和强度的影响。在非饱和土三轴试验结果表明,即使在净应力和吸力路径相同的条件下,具有不同饱和度试样的应力-应变关系和强度也是不同的。其他条件相同时,试样饱和度越高,其应力比-应变关系曲线越高,强度越大。最新的水力-力学特性耦合的弹塑性本构模型可以定量地表示上述非饱和土的性质     

控制吸力循环荷载下非饱和黏性土的弹塑性双面模型

建立非饱和土在动态荷载作用下的本构模型有助于解决相关的工程问题。在塑性增量流动理论框架内,将BBM(BarcelonaBasicModel)模型与笔者提出的塑性硬化准则相结合,考虑控制吸力的循环荷载作用,建立了一个描述非饱和黏性土的弹塑性双面模型。该模型包含一个边界面和一个几何相似的加载面,二者结合记忆中心的概念,共同描述应力路径周期性改变加载方向时非饱和土的非线性、循环塑性和变形累积特性。采用动三轴剪切试验确定了一种非饱和粘质粉土的动态力学特性,分析了吸力、净围压和动应力幅值对循环塑性的影响。模型预测与非饱和土在静、动态加载下的试验结果的对比显示,二者吻合较好,表明所建弹塑性双面模型能够模拟非饱和土在控制吸力循环荷载作用下的力学行为。     

非饱和土水-力本构模型及其隐式积分算法

在已有工作基础上建立了水力-力学耦合的非饱和土本构模型,在硬化方程中考虑饱和度的影响,同时在土水特征曲线中考虑了塑性体变的影响,从而使模型可以反映非饱和土中的毛细现象与土中弹塑性变形现象的耦合行为。采用隐式积分方法,建立了非饱和土耦合模型的数值模型,并推导了得到了水力-力学耦合的非饱和土的一致切线模量。利用该算法编制了本构模型计算的子程序,使其能向外输出切线刚度矩阵,用于有限元计算。为了验证该算法和程序的正确性,用所编制程序对不同路径下的土体行为进行了预测。通过预测结果与试验结果相对比,表明程序预测结果与试验数据相吻合,模型可以较好地模拟土体的水力-力学耦合行为特性。     

非饱和土化学-水力-力学耦合行为数值模拟

在描述非饱和土力学本构行为的Gens-Alonso模型[1]的基础上,结合化学浓度对前固结压力的软化公式[2],并考虑了化学浓度对黏聚力的软化作用,建立了描述非饱和土化学-水力-力学耦合行为的本构模型。对包括化学-水力-力学本构关系、流体流动和污染物传输的控制方程的平衡方程组进行有限元离散,并采用此非饱和土化学-水力-力学耦合行为的数值模型对非饱和土中隧道周围化学-水力-力学耦合过程进行了模拟,对纯粹的力学响应、弹性化学力学响应、弹塑性化学力学响应 3 种情况进行了分析,数值结果显示了化学浓度作用下隧道周围的体积变化量和应力状态比单纯的力学响应有较大的提高,隧道表面的收缩量也有明显的增大。数值模拟的结果显示了该方法对模拟非饱和土复杂的耦合行为的可行性。     

控制吸力循环荷载下非饱和黏性土的弹塑性双面模型

建立非饱和土在动态荷载作用下的本构模型有助于解决相关的工程问题。在塑性增量流动理论框架内,将BBM(Barcelona basic model)模型与笔者提出的塑性硬化准则相结合,考虑控制吸力的循环荷载作用,建立了一个描述非饱和黏性土的弹塑性双面模型。该模型包含一个边界面和一个几何相似的加载面,二者结合记忆中心的概念,共同描述应力路径周期性改变加载方向时非饱和土的非线性、循环塑性和变形累积特性。采用动三轴剪切试验确定了一种非饱和黏质粉土的动态力学特性,分析了吸力、净围压和动应力幅值对循环塑性的影响。模型预测与非饱和土在静、动态加载下的试验结果的对比显示,二者吻合较好,表明所建立的弹塑性双面模型能够模拟非饱和土在控制吸力循环荷载作用下的力学行为。     

一个高饱和度非饱和土的本构模型

高饱和度的非饱和土中由于气体处于封闭状态,其内部气压的变化必将对土体的行为产生影响。首先,对高饱和度非饱和土特性进行探讨和研究,随后,在已有非饱和土模型框架基础上,采用广义有效应力原理,建立一个适用于高饱和度条件下的非饱和土的弹塑性本构模型。模型中引入气相耗散的影响,在硬化方程中考虑封闭气体压力改变的影响。最后,利用已有的试验结果来对模型进行验证,并将模型预测结果与前人模型进行对比,表明模型预测可以很好地预测土体的行为,尤其是在高饱和度条件下其结果比其他模型更加接近实际情况。     

非饱和土毛细滞回与变形耦合弹塑性本构模型

在修正剑桥模型的基础上,提出了一个非饱和土毛细滞回与骨架变形耦合的弹塑性本构模型。该模型考虑了基质吸力与饱和度对屈服应力的影响,可以同时描述非饱和土的弹塑性变形特性与毛细循环滞回效应。根据塑性体变的产生使非饱和土进气值增大的特点,建立了变形对土-水特征曲线影响的数学描述。该模型有效地考虑了饱和度对前期屈服应力的作用,准确地反映了土体在不同土-水状态条件下（脱湿和吸湿过程）强度特性的变化,而且还可以有效地描述水力循环历史对土体变形的影响。通过与试验数据对比,证明了该模型能够模拟非饱和土的主要力学特性。     

非饱和土弹塑性模型参数的试验确定及有限元法

简要介绍广泛应用的非饱和土Alonso模型的原理与发展,并通过3组共7个试样的非饱和土三轴试验,得到模型的11个参数。在饱和土Cam本构关系的基础上,推导出一个基于非饱和土Alonso模型的应力-应变增量方程的计算公式,该方程与饱和土的本构方程形式相同。编制了能够考虑净应力和吸力二者对土体硬化规律影响的有限元程序,从而为非饱和土弹塑性计算提供一条途径,便于进一步应用于实际工程。     

A density‐dependent elastoplastic hydro‐mechanical model for unsaturated compacted soils

This paper presents a three‐dimensional elastoplastic constitutive model for predicting the hydraulic and mechanical behaviour of unsaturated soils. It is based on experimental results obtained from a series of controlled‐suction triaxial tests on unsaturated compacted clay with different initial densities. Hydraulic hysteresis in the water‐retention behaviour is modelled as an elastoplastic process, with the elastic part modelled by a series of scanning curves and the elastoplastic part modelled by the main drying and wetting curves. The effect of void ratio on the water‐retention behaviour is studied using data obtained from controlled‐suction wetting–drying cyclic tests on unsaturated compacted clay with different initial densities. The effect of the degree of saturation on the stress–strain‐strength behaviour and the effect of void ratio on the water‐retention behaviour are considered in the model, as is the effect of suction on the hydraulic and mechanical behaviour. The initial density dependency of the compacted soil behaviour is modelled by experimental relationships between the initial density and the corresponding yield stress and, thereby, between the initial density and the normal compression line. The model is generalized to three‐dimensional stress states by assuming that the shapes of the failure and yield surfaces in the deviatoric stress plane are given by the Matsuoka–Nakai criterion. Model predictions of the stress–strain and water‐retention behaviour are compared with those obtained from triaxial tests with different initial densities under isotropic compression, triaxial compression and triaxial extension, with or without variation in suction. The comparisons indicate that the model accurately predicts the hydraulic and mechanical behaviour of unsaturated compacted soils with different initial densities using the same material constant. Copyright © 2006 John Wiley & Sons, Ltd.     

A bounding surface plasticity model for unsaturated soil at small strains

Most existing hydromechanical models for unsaturated soils are not able to fully capture the nonlinearity of stress–strain curves at small strains (less than 1%). They cannot therefore, for example, accurately predict ground movements and the performance of many earth structures under working conditions. To tackle this problem, a state‐dependent bounding surface plasticity model has been newly developed. Particularly, the degradation of shear modulus with strain at small strains ranging from 0.001% to 1% is focused. The proposed model is formulated in terms of mean average skeleton stress, deviator stress, suction, specific volume and degree of saturation. Void ratio‐dependent hydraulic hysteresis is coupled with the stress–strain behaviour. Different from other elastoplastic models for unsaturated soils, plastic strains are allowed inside bounding surfaces. In this paper, details of model formulations and calibration procedures of model parameters are presented. To evaluate the capability of the new model, it is applied to simulate a series of triaxial compression tests on compacted unsaturated silt at various suctions. Effects of suction, drying and wetting as well as net stress on unsaturated soil behaviour are well captured. The model shows good predictions of the degradation of shear modulus with strain over a wide range of strains from 0.001% to 1%. Copyright © 2015 John Wiley & Sons, Ltd.     

Coupled modelling of hydro‐mechanical behaviour of unsaturated compacted expansive soils

The Barcelona basic model cannot predict the mechanical behaviour of unsaturated expansive soils, whereas the Barcelona expansive model (BExM) can only predict the stress–strain behaviour of unsaturated expansive soils without the water‐retention behaviour being incorporated. Moreover, the micro‐parameters and the coupling function between micro‐structural and macro‐structural strains in the BExM are difficult to determine. Experimental data show that the compression curves for non‐expansive soils under constant suctions are shifted towards higher void ratios with increasing suction, whereas the opposite is true for expansive soils. According to the observed water‐retention behaviour of unsaturated expansive soils, the air‐entry value increases with density, and the relationship between the degree of saturation and void ratio is linear at constant suction. According to the above observation, an elastoplastic constitutive model is developed for predicting the hydraulic and mechanical behaviour of unsaturated expansive soils, based on the existing hydro‐mechanical model for non‐expansive unsaturated soil. The model takes into consideration the effect of degree of saturation on the mechanical behaviour and that of void ratio on the water‐retention behaviour. The concept of equivalent void ratio curve is introduced to distinguish the plastic potential curve from the yield curve. The model predictions are compared with the test results of an unsaturated expansive soil, including swelling tests under constant net stress, isotropic compression tests and triaxial shear tests under constant suction. The comparison indicates that the model offers great potential for quantitatively predicting the hydraulic and mechanical behaviour of unsaturated expansive soils. Copyright © 2011 John Wiley & Sons, Ltd.     

Three‐dimensional elasto‐plastic model for unsaturated compacted soils with different initial densities

This paper presents an elasto‐plastic model for unsaturated compacted soils and experimental results obtained from a series of suction‐controlled triaxial tests on unsaturated compacted clay with different initial densities. The initial density dependency of the compacted soil behaviour is modelled by establishing experimental relationships between the initial density and the corresponding yield stress and thereby between the initial density and the location and slope of normal compression line. The model is generalized to three‐dimensional stress states by assuming that the shapes of the failure surface and the yield surface in the deviatoric plane are given by the extended SMP criterion. A considerable number of the isotropic compression, triaxial compression and extension tests on unsaturated compacted clay with different initial densities were performed using a suction‐controllable triaxial apparatus, to measure the stress–strain–volume change in different stress paths and wetting paths. The model has well‐predicting capabilities to reproduce the mechanical behaviour of specimens compacted under different conditions not only in isotropic compression but also in triaxial compression and triaxial extension. Copyright © 2003 John Wiley & Sons, Ltd.     

A kinematic hardening based model for unsaturated soils considering different hydraulic conditions

At present, several of the existing elastoplastic constitutive models are adapted for describing the stress–strain behavior of unsaturated soils. However, most of them present certain limitations in this field. These limitations can be related to the basic model and/or added unsaturated state variables and formulations. In this regard, inability to model the hydro‐mechanical behavior in constant water (CW) conditions is an example of these limitations. In this paper, an advanced version of CJS model is selected for adaptation to the unsaturated states. Adaptation to unsaturated states is achieved in the framework of effective stress approach. Effective stress equation and unsaturated state variables are selected based on the recent research existing in the literature. The developed model is capable of describing the complex behavior of unsaturated soil in the CW condition in addition to predicting the behavior at failure and post–failure, nonlinear elastoplastic behavior at low levels of stress and strain (by selecting a very small elastic domain), as well as wetting and collapse behaviors. In order to validate the model, results of triaxial tests in CD and CW conditions are used. The validation results indicate the good capability of the proposed model. Behavior of the unsaturated soils during wetting is an important issue. For this reason, the model is also evaluated based on the results of wetting and collapse triaxial tests. A comparison between the tests and simulation results shows that the model is able to predict the soil behavior under the wetting path. Copyright © 2016 John Wiley & Sons, Ltd.     

不饱和土动弹塑性本构模型研究

以饱和度与有效应力为状态变量,通过引入描述不饱和与饱和土孔隙比差的状态变量,将Zhang等提出的饱和土体应力诱导各向异性动弹塑性本构模型推广到不饱和土体中,使其可描述不饱和土在动力循环荷载作用下的力学特性行为。通过对已有不饱和土体在完全不排水条件下的动三轴试验进行理论模拟,验证了所提出不饱和土本构模型的正确性。最后基于所提出本构模型,讨论了在不排水条件下初始饱和度对不饱和土动力特性研究。结果表明,不饱和土在动力荷载作用下,土体的孔隙比将减少,导致饱和度增加;当初始饱和度较高时,不饱和土会转化为饱和土,从而发生液化现象。该研究成果对研究不饱和土在地震等动力荷载作用下的力学特性行为具有重要意义。     

A unified constitutive model for unsaturated soil under monotonic and cyclic loading

This study presents a sophisticated elastoplastic constitutive model for unsaturated soil using Bishop-type skeleton stress and degree of saturation as state variables in the framework of critical state soil mechanism. The model is proposed in order to describe the coupled hydromechanical behavior of unsaturated soil irrespective of what kind of the loadings or the drainage conditions may be. At the same time, a water retention characteristic curve considering the influence of deformation on degree of saturation is also proposed. In the model, the superloading and subloading concepts are introduced to consider the influences of overconsolidation and structure on deformation and strength of soils. The proposed model only employs nine parameters, among which five parameters are the same as those used in Cam-Clay model. The other four parameters have the clear physical meanings and can be easily determined by conventional soil tests. The capability and accuracy of the proposed model have been validated carefully through a series of laboratory tests such as isotropic loading tests and triaxial monotonic and cyclic compression tests under different mechanical and hydraulic conditions.