半潜式起重平台系泊系统设计与优化研究

近年来,国内兴起了大力发展半潜式起重平台的势头,系泊系统的设计与优化是该类型平台开发中的关键问题之一。采用时域方法对半潜式起重平台系泊系统进行耦合动力分析,研究系泊系统主要参数对其动力响应特性的影响,并给出主要参数的设计优化流程,在此基础上,以能够满足安全校核且性能较优的系泊方案为目标,对该半潜式起重平台的系泊系统进行优化设计,并研究单根系泊缆发生破断对整个系泊系统的影响。结果表明:基于主要参数对系泊性能的影响规律,经优化设计得到的系泊方案,预留的安全欲度适中,能够保障半潜式起重平台在恶劣海况下的生存能力,同时具备较好的经济性。     

深水半潜式平台系泊系统动力特性研究

探讨张紧式系泊系统的基本特征,比较张紧式和悬链线式系泊半潜平台运动和动力响应特性,分析拖曳力系数变化对张紧式和悬链线式系泊动力效应的影响,以及张紧式和悬链线式系泊缆节点运动特点,从而为改善半潜平台系泊系统动力效应提供参考.     

半潜式平台运动及系泊系统特性研究

针对深海半潜式平台及其系泊系统的水动力特性,运用时域耦合的分析方法,对一座水深为1 000 m的半潜式平台,及其悬链线式系泊系统的水动力性能进行探索,获得频域和时域响应结果。同时阐述了平台系泊系统的设计流程,并通过系泊系统参数的变化,研究其特性寻找影响系泊系统作用的一般规律,为平台及其系泊系统设计提供参考。     

深水半潜式平台张拉锚泊系统失效分析

针对深水半潜式平台在极端工况下张拉锚泊系统失效情况,基于板锚失效上拔过程中位移与承载力的关系曲线,提出在AQWA软件中用非线性锚缆模拟板锚走锚过程的方法,对深水半潜式平台张拉锚泊系统在百年一遇工况下断锚、走锚情况的平台响应、锚缆拉锚力及最大缆张力进行分析。研究表明:断锚时各锚链拉力瞬变,平台迅速发生大距离偏移;走锚时随着板锚的拔出各锚链上的拉力逐渐增大,平台位置逐渐偏移,最后达到平衡状态。单缆断锚时,迎浪向5号锚缆拉力最大;单缆断锚且单锚走锚时,3、6号锚缆拉锚力最大。失效缆超过一根时,平台偏移和单缆最大缆张力均超出规范要求,同时其它锚缆最大拉锚力极有可能出现超过板锚极限承载力的情况,最终造成整个锚泊系统破坏。     

安装误差对半潜漂浮式风机悬链线系泊系统性能的影响

由于浅水深条件下悬链线系泊系统的性能对系泊缆长度和几何形状更为敏感,悬链线系泊系统的安装误差对其性能的影响较深水条件下的更为显著。因此首先对适用于半潜漂浮式风机的悬链线系泊系统施工进行研究,分别确定了锚安装位置误差、系泊缆预铺误差和系泊缆与漂浮式基础回接误差的来源,并根据施工条件给出了误差值。之后,以浮体动力学仿真作为手段,对系泊缆系统施工误差对其性能的影响进行基于时域仿真的量化研究。研究表明,锚安装位置误差对系泊系统性能影响不大,但系泊缆预铺和回接的误差对系泊系统性能的影响较大。系泊缆回接的误差可造成系泊缆张力平均值和标准差与设计值偏差近20%,可能对系泊系统疲劳寿命评估产生较大的影响。与系泊缆回接误差相比,系泊缆预铺误差的产生原因更为复杂,由于系泊缆预铺误差往往导致系泊缆长度增长,存在误差的系泊缆张力的各项统计值总体偏小,但可能会造成同组无误差系泊缆的张力过载。     

深水圆筒型钻井平台张紧式系泊系统设计

基于我国南海海域环境条件,对一座深水圆筒型钻井平台设计一套张紧式系泊定位系统,利用SESAM软件对平台运动响应和缆索张力进行分析计算,得到主要运动响应为纵荡、纵摇和垂荡。分别考虑0°和180°的环境载荷方向,对比得到0°方向的缆索张力更大,且6号和7号缆承受了主要的环境力。分析了平台运动的影响因素,认为缆索夹角设定为35°时较优,适度增大系泊缆初始长度和减小两端锚链长度可较为有效地降低系泊缆受力,系泊缆总根数保持12时（4根×3组）为最优方案。根据分析结果对初始系泊方案进行了优化,在风暴工况下系泊缆最大受力减小了约14.8%。钻井作业工况和一根系泊缆破断工况下,系泊缆受力和平台位移均能满足规范要求。     

深水锚泊定位半潜式钻井平台性能数值与试验研究

近年来,深水半潜平台已成为海洋工程领域研究的热点。分别通过模型试验和数值模拟的方法,对不同水深和浪向条件下作业的深水半潜平台的运动以及系泊系统的受力进行全面分析。在此基础上,进一步研究平台在深水作业时的运动和动力特性,以及水深和环境海况的变化对平台运动和系泊系统受力的影响规律。同时,对比完整系泊系统的情况,对一根系泊缆破断的极端状态下平台的特性开展研究,获得运动和系泊系统受力的变化规律。对比发现试验和数值的结果能较好地相互吻合,且均能满足相应的安全度要求,保证平台实际作业时的可靠性,为深水半潜平台设计中的安全极限计算提供一定的依据。     

内孤立波中半潜平台动力响应特性

基于内孤立波mKdV理论,采用时域有限位移运动方程,结合改进的Morison公式,研究了两层流体中内孤立波与带分段式悬链系泊约束半潜平台的相互作用问题。针对东沙群岛南部海域附近某实测内孤立波特征参数,计算分析了在该内孤立波作用下SEDCO-700型半潜平台的内孤立波载荷、运动响应及其系泊张力的变化特性。研究表明,内孤立波不仅会对半潜平台产生突发性冲击载荷作用,使其产生大幅度水平漂移运动,并导致其系泊张力显著增大,因此在半潜平台等深海平台的设计与应用中,内孤立波的影响是不可忽视的。     

一种新型Semi-Spar式海上风机平台系泊系统优化分析

参考英国的Kincardine风机采用的新式的Semi-Spar概念,结合spar式基础和半潜式基础的特点,提出了一种新式海上浮式风机平台模型,并基于三维势流理论,利用AQWA软件进行水动力计算,验证新式平台可靠性。分析了在风、浪、流荷载联合作用下,锚链竖向夹角、系缆数量对风机浮式平台运动性能和系泊张力的影响,对系泊系统进行优化,并验证极端工况下的可靠性。结果证明风机平台水平运动和纵摇运动幅值较小,但垂荡幅值略大,而通过减小锚链竖向夹角可以控制平台运动响应幅值,增加系缆数量可以同时减小系泊张力大小。计算结果证明了新型Semi-Spar式海上风机平台可行性,为浮式风机平台及系泊系统的设计提供参考。     

系泊定位状态下半潜式浮体波浪爬升性能试验研究

随着深海油气田的快速发展,新兴的浮式生产系统,尤其是半潜式平台,由于具有性能优良、运动响应小、工作水深适用范围广、抗风浪荷载能力强等优点,在工程实际中得到快速的发展。在半潜式平台设计过程中,气隙和斜浪作用下的波浪爬升问题对其安全性能的影响至关重要。通过采用系泊定位状态下的四立柱半潜式平台进行波浪爬升实验,对平台不同位置进行全方位的监测,而后对测量数据进行分析,得出关于海浪对半潜式平台气隙响应的影响和相关规律,为半潜式平台的设计提供参考。     

半潜式钻井平台复合锚泊系统组分配比优化设计

从提高锚泊系统收放时效性入手,提出了一种半潜式钻井平台复合式锚泊系统组分配比优化设计方法,旨在尽可能降低复合式锚泊系统的钢链配比长度,提高收放效率。结合锚泊系统设计参数,制定优化设计准则,建立优化分析流程,采用ANSYS-AQWA建立锚泊定位半潜式平台水动力分析模型,获得平台运动参数和锚链动力参数,对平台漂移量、锚链最小安全系数、走锚临界张力、锚链最小卧底长度和起锚力进行无量纲指标分析,并综合考虑张力倾角与预张力对优化结果的影响,获得复合式锚泊系统钢链与钢缆的最优配比关系,确定最优钢链长度为395 m,较原钢链长度缩短225 m,钢链收放时间降低36%,进一步提高锚泊系统收放时效性,并降低平台可变荷载。     

Effect of Failure Mode of Taut Mooring System on the Dynamic Response of A Semi-Submersible Platform

Mooring system failure can lead to largely different dynamic response of floating structures when compared to the response under the condition of intact mooring system. For a semi-submersible platform with taut mooring system under extreme environmental conditions, the typical mooring system failure includes anchor line breaking failure due to the broken anchor line, and the anchor dragging failure caused by the anchor failure in the seabed soil due to the shortage of the anchor bearing capacity. However, study on the mooring failure caused by anchor failure is rare. The current work investigates the effect of three failure modes of taut mooring system on dynamic response of a semi-submersible platform, including one line breaking failure, two lines breaking failure, and one line breaking with one line attached anchor dragging failure. The nonlinear polynomial mooring line model in AQWA was used with integrating the load and displacement curve from the anchor pulling study to characterize the anchor dragging behavior for mooring system failure caused by the anchor failure. The offsets of the platform and the tension of mooring lines were analyzed for mooring system failure with 100-year return period. It is found that the mooring failure of one line breaking with one line attached anchor dragging is a case between the other two mooring failures. The traditional mooring analysis considering only the damaged condition with one line breaking is not safe enough. And the simple way of mooring analysis of two lines breaking is too conservative for the costly offshore engineering.

     

Dynamic Analysis of Semi-Submersible Production Platform Under the Failure of Mooring Lines

This paper quantitatively studies the transient dynamic response of a semi-submersible production platform with the loss of one or several positioning mooring lines.A semi-submersible platform,production risers,and positioning mooring lines are all included in the numerical simulation.Increased motion of the semi-submersible platform,tension variation of the remaining mooring lines/risers and the risk of mooring line or riser clashing are all investigated through fully coupled time-domain analysis.Combined environmental loads are selected from irregular waves and the steady current varying from very rough to extreme sea conditions.Three dimension radiation/diffraction theories and Morison’s equation are applied to calculate first-order wave force and second-order mean drift force of floating semi-submersible platform.Nonlinear time-domain finite element methods are employed to analyze the behavior of mooring lines and risers.Results show that the failure of mooring lines seriously reduce the platform’s stability performance.The tension of the rest lines is also increased accordingly.Remaining lines which are closer to the failed lines will have larger tension increase to compensate.Line-Line distance provides practical information for the risk of clashing investigation.     

锚泊辅助动力定位系统单缆失效影响研究

针对半潜式钻井平台锚泊辅助动力定位系统在海上作业时可能会出现的单缆失效情况。以一艘半潜式平台为例,设计锚泊辅助动力定位系统。通过全动态时域模拟,研究不同的单缆失效模式对半潜式平台锚泊辅助动力定位系统功率消耗、定位精度、缆绳张力等的影响。根据分析结果,在极端海况下,松弛锚泊辅助动力定位系统的背风缆有助于降低定位系统的功率消耗,提高定位精度和系统的安全性,从而为锚泊辅助动力定位系统的工程应用提供一些参考。     

深水半潜式平台锚链倾角监测的自容式传感器的设计

深水半潜式平台系泊锚链的倾角变化是评价平台系泊状态与锚链受力的重要指标,是半潜式平台重要的监测内容。目前,深水锚链的测量主要是采用自容式的传感器,针对其水下长时间测量的应用特点,要求它的设计必须具有低功耗、高可靠性、大存储量、体积小、防水耐压等指标。根据我国南海流花平台的锚链监测需要,设计与制作了专用的水下自容式倾角传感器,并在实际应用中进行了检验。     

Sensitivity Analysis of Air Gap Motion with Respect to Wind Load and Mooring System for Semi-Submersible Platform Design

A design of semi-submersible platform is mainly based on the extreme response analysis due to the forces experienced by the components during lifetime. The external loads can induce the extreme air gap response and potential deck impact to the semi-submersible platform. It is important to predict air gap response of platforms accurately in order to check the strength of local structures which withstand the wave slamming due to negative air gap. The wind load cannot be simulated easily by model test in towing tank whereas it can be simulated accurately in wind tunnel test. Furthermore, full scale simulation of the mooring system in model test is still a tuff work especially the stiffness of the mooring system. Owing to the above mentioned problem, the model test results are not accurate enough for air gap evaluation. The aim of this paper is to present sensitivity analysis results of air gap motion with respect to the mooring system and wind load for the design of semi-submersible platform. Though the model test results are not suitable for the direct evaluation of air gap, they can be used as a good basis for tuning the radiation damping and viscous drag in numerical simulation. In the presented design example, a numerical model is tuned and validated by ANSYS AQWA based on the model test results with a simple 4 line symmetrical horizontal soft mooring system. According to the tuned numerical model, sensitivity analysis studies of air gap motion with respect to the mooring system and wind load are performed in time domain. Three mooring systems and five simulation cases about the presented platform are simulated based on the results of wind tunnel tests and sea-keeping tests. The sensitivity analysis results are valuable for the floating platform design.     

立管对深水半潜式生产平台定位性能影响研究

基于三维频域势流理论,计算船体的水动力参数;采用动态耦合方法分析了深海半潜式生产平台各系统之间的相互作用特征,研究了立管系统对锚泊系统定位能力的影响。计算结果表明,立管系统在一定程度上增加了整个系统的刚度,其所受的附加质量和阻尼可降低平台的低频响应,从而降低平台的偏移和系泊缆的张力;海流将增大立管上的拖曳力,使平台偏移更远,锚索上的张力更大;立管系统对锚泊系统定位性能的最终影响需综合考虑多种因素的叠加。对目标平台而言,由于服役海域的流速较大,对立管的拖曳作用较为明显。因此,为确保平台的安全性,当服役海域流速较大时,带有多立管的平台,其锚泊系统的设计应考虑立管的影响。     

Artificial Neural Networks for the analysis of spread⿿mooring configurations for floating production systems

This work presents the development of Artificial Neural Networks for the analysis of any arbitrarily defined spread-mooring configuration for floating production systems (FPS), considering a given scenario characterized by the water depth, metocean data, characteristics of the platform hull, and the riser layout. The methodology is applied to recent designs of deepwater semi-submersible platforms connected to a large number of risers with asymmetrical layout. In such cases, the design variables may include values for the azimuthal spacing and mooring radius varying along the corners of the platform, besides the pretension and material of the lines. The results of the case study indicated that, given any mooring configuration characterized by the combination of all these design variables, the ANNs provide fairly accurate values for the parameters of the response that are required for the design of mooring systems (typically platform offsets and line tensions).