共查询到20条相似文献,搜索用时 578 毫秒
1.
续航力与水平速度均是水下滑翔器的重要性能指标。采用单位重量滑翔器、单位水平速度所耗功率作为滑翔效率的评价指标,以一新型扁平型水下滑翔器为研究对象,利用 CFD 计算结合模型试验验证的方法获取了所需的流体动力系数,然后进行了滑翔运动分析及垂直面滑翔运动仿真计算,得到了最优滑翔运动参数。 建立的滑翔性能计算方法对扁平型水下滑翔器水动力性能设计及滑翔运动参数优化有着重要的应用价值。 相似文献
2.
3.
采用标准k-ε两方程涡粘性模型,压力的隐式算子分割算法(PISO)求解时均Reynolds方程(RANS),对三种新型无尾翼水下滑翔器的升阻比性能进行研究。先对滑翔器摩擦阻力的CFD模拟结果与理论计算结果进行对比分析,验证CFD模拟结果的合理性与可靠性;再对不同迎流速度、不同速度攻角下的试验工况进行数值模拟,分析不同试验工况下滑翔器的粘压阻力与升力,得到不同试验工况下滑翔器的升阻比性能。研究结果表明,新型无尾翼水下滑翔器在5°~15°攻角区间内具有良好的升阻比,小攻角下圆碟型和飞碟型滑翔器的升阻比性能优于椭圆型滑翔器,而大攻角下椭圆型滑翔器相对其它两种具有更佳的升阻比性能,为新型无尾翼水下滑翔器升阻比性能的研究提供一定的思路。 相似文献
4.
5.
6.
7.
水下滑翔机器人运动机理仿真与实验 总被引:1,自引:0,他引:1
对水下滑翔机器人SEA-WING的定常滑翔运动和空间定常螺旋回转运动进行机理分析,针对其特定水动力系数进行仿真,得出其运动机理特性.在此基础上,通过湖试实验数据对仿真结果进行验证,认为对于定常滑翔运动,以约36°航迹角滑行可得到最大水平速度;在相同航迹角航行情况下,水平方向速度随净浮力的增大而增大.对于定常回转运动,回转半径由载体的质量、俯仰角、水动力参数、横滚角确定.在质量和俯仰角保持不变条件下,横滚角对回转半径的影响较明显,系统的回转半径可以通过控制横滚角来实现的. 相似文献
8.
9.
10.
混合驱动自主潜航器融合了自主潜航器机动灵活和水下滑翔机续航能力强的优点,针对自身携带能源有限的问题,对在两种工作模式下如何实现最大航行距离进行了研究.从航行过程中的能源消耗入手,得出航行距离与速度、电子设备功率等的关系,通过理论分析和仿真手段得出最大续航能力的实现方法.在螺旋桨驱动模式下,当以经济航速航行时,可以达到最大航行距离;在浮力驱动模式下,当以最大滑翔效率航行时,水平方向上的滑翔距离最大,并且水平方向上的滑翔距离随着剖面深度的增大而增大,当剖面深度大到一定程度之后,最大滑翔距离趋于恒定.该研究方法可为类似水下航行器电源管理系统的能源分配提供参考,也可为航行器外形的设计和传感器的选型提供理论指导. 相似文献
11.
R. Shafaghat S.M. HosseinalipourI. Lashgari A. Vahedgermi 《Applied Ocean Research》2011,33(3):193-198
The reduction of energy consumption for high speed submersible bodies is an important challenge in hydrodynamic researches. Supercavitation is a hydrodynamic process in which a submerged body gets enveloped in a layer of gas. As the density and viscosity of the gas is much lower than that of seawater, skin friction drag can be reduced considerably. If the nose of the body (cavitator) has a proper shape, the attendant pressure drag remains at a very low value, so the overall body drag reduces significantly. Total drag force acting on the supercavitating self-propelled projectiles dictates the amount of fuel consumption and thrust requirements for the propulsion system to maintain a required cavity at the operating speed. Therefore, any reduction in the drag coefficient, by modifying the shape of the cavitator to achieve optimal shape, will lead to a decrease of this force. The main objective of this study is to optimize the axisymmetric cavitator shape in order to decrease the drag coefficient of a specified after-body length and body velocity in the axisymmetric supercavitating potential flow. To achieve this goal, a multi-objective optimization problem is defined. NSGA II, which stands for Non-dominated Sorting Genetic Algorithm, is used as the optimization method in this study. Design parameters and constraints are obtained according to the supercavitating flow characteristics and cavitator modeling. Then objective functions will be generated using the Linear Regression Method. The results of the NSGA II algorithm are compared with those generated by the weighted sum method as a classic optimization method. The predictions of the NSGA II algorithm seem to be excellent. As a result, the optimal cavitator’s shapes are similar to a cone. 相似文献
12.
13.
Drag anchor is one of the most commonly used anchorage foundation types. The prediction of embedded trajectory in the process of drag anchor installation is of great importance to the safety design of mooring system. In this paper, the ultimate anchor holding capacity in the seabed soil is calculated through the established finite element model, and then the embedded motion trajectory is predicted applying the incremental calculation method. Firstly, the drag anchor initial embedded depth and inclination angle are assumed, which are regarded as the start embedded point. Secondly, in each incremental step, the incremental displacement of drag anchor is added along the parallel direction of anchor plate, so the displacement increment of drag anchor in the horizontal and vertical directions can be calculated. Thirdly, the finite element model of anchor is established considering the seabed soil and anchor interaction, and the ultimate drag anchor holding capacity at new position can be obtained. Fourthly, the angle between inverse catenary mooring line and horizontal plane at the attachment point at this increment step can be calculated through the inverse catenary equation. Finally, the incremental step is ended until the angle of drag anchor and seabed soil is zero as the ultimate embedded state condition, thus, the whole embedded trajectory of drag anchor is obtained. Meanwhile, the influences of initial parameter changes on the embedded trajectory are considered. Based on the proposed method, the prediction of drag anchor trajectory and the holding capacity of mooring position system can be provided. 相似文献
14.
An inverse hull design approach in minimizing the ship wave 总被引:1,自引:0,他引:1
The Levenberg–Marquardt Method (LMM) and a panel code for solving the wave-making problem are utilized in an inverse hull design problem for minimizing the wave of ships. A typical catamaran is selected as the example ship for the present study. The hull form of the catamaran is described by the B-spline surface method so that the shape of the hull can be completely specified using only a small number of parameters (i.e. control points). The technique of parameter estimation for the inverse design problem is thus chosen. The LMM of parameter estimation, which is the combination of steepest descent and Newton’s methods, has been proven to be a powerful tool for the inverse shape design problem. For this reason it is adopted in the present study.In the present studies, the inverse hull design method can not only be applied to estimate the hull form based on the known wave data of the target ship but can also be applied to estimate the unknown hull form based on the reduced wave height. The optimal hull forms of minimizing wave for a typical catamaran in deep water at service speed and at the critical speed of shallow water are estimated, respectively. Moreover, a new hull form with the combining feature of the optimal hull forms for deep water and shallow water is performing well under both conditions. The numerical simulation indicates that the hull form designed by inverse hull design method can reduce the ship wave significantly in comparison with the original hull form. 相似文献
15.
以实际环境荷载作用下的实际海洋导管架平台结构为对象,研究了海洋平台结构在风,流,海冰等多荷载模式和多荷载工况下的优化设计的理论方法和应用技术,建立了结构尺寸优化,形状优化和拓扑优化问题的统一模型。计算结果反映出形状优化比尺寸优化所得设计更优,而拓扑优化的设计效果最好。不同的荷载工况对应的最优拓扑形式不同,因此在实际设计中应考虑实际的荷载工况,选取不同的拓扑形式。 相似文献
16.
17.
Traditionally autonomous underwater vehicles (AUVs) have been built with a torpedo-like shape. This common shaping is hydrodynamically suboptimal for those AUVs required to operate at snorkeling condition near the free surface. In this case, the wave resistance associated to the wavy deformation of the sea surface induced by the motion of the platform is an important component of the drag. This work has investigated the optimum hull shape of an underwater vehicle moving near the free surface. Specifically a first-order Rankine panel method has been implemented to compute the wave resistance on a body of revolution moving close to the free surface. A simulated annealing algorithm was then employed to search those set of parameters defining the hull shape that minimize the wave resistance. The optimization was constrained to keep constant the total volume of the vehicle. The total drag of scaled models of the torpedo-like and resulting optimum shapes was measured in the naval tank of the University of Trieste. Measurements showed a smaller resistance of the optimized shape in the range of the considered Froude numbers. 相似文献
18.
Shape optimization of two-dimensional cavitators in supercavitating flows, using NSGA II algorithm 总被引:1,自引:0,他引:1
The reduction of energy consumption of high speed submersible bodies is an important challenge in hydrodynamic researches. In this paper, shape optimization of two-dimensional cavitators in supercavitating flows is studied. A two dimensional supercavitation potential flow passes a symmetric two dimensional cavitator, which is placed perpendicular to the flow in a channel of infinite length and immediately a cavity is formed behind the cavitator. This is because of the generation of a gas or vapor cavity between the body and the surrounding liquid due to the change in a high speed flow direction passing the cavitator. Drag force acting on this supercavitating body dictates the thrust requirements for the propulsion system, to maintain a required cavity at the operating speed. Therefore, any reduction in the drag force, by modifying the shape of the cavitator, will lead to decrease this force. This study concentrates on the optimization of two dimensional cavitators in order to decrease drag coefficient for a specified after body length and velocity in a potential flow. To achieve this goal a multi-objective optimization problem is defined to optimize cavitator shapes in supercavitating flow. The so-called NSGA II (Non-dominated Sorting Genetic Algorithm) algorithm is used as an optimization method. Design parameters and constraints are obtained according to supercavitating flow characteristics and cavitator modeling and objective functions are generated using Linear Regression Method. The obtained results are compared with other classic optimization methods, like the weighted sum method, for validation. 相似文献
19.
Positioning drag anchors in seabed soils are strongly influenced not only by the properties of the anchor and soil,but also by the characteristics of the installation line.The investigation on the previous prediction methods related to anchor positioning demonstrates that the prediction of the anchor position during dragging has inevitably introduced some key and unsubstantiated hypotheses and the applicability of these methods is limited.In the present study,the interactional system between the drag anchor and installation line is firstly introduced for the analysis of anchor positioning.Based on the two mechanical models for embedded lines and drag anchors,the positioning equations for drag anchors have been derived both for cohesive and noncohesive soils.Since the drag angle at the shackle is the most important parameter in the positioning equations,a novel analytical method that can predict both the variation and the exact value of the drag angle at the shackle is proposed.The analytical method for positioning drag anchors which combines the interactional system between the drag anchor and the installation line has provided a reasonable theoretic approach to investigate the anchor behaviors in soils.By comparing with the model flume experiments,the sensitivity,effectiveness and veracity of the positioning method are well verified. 相似文献
20.
针对深海采矿实际需求,提出将集矿车上的液压站与集矿车分离,设计成相对独立、悬浮于集矿车前部上方的浮游体。设计了多金属结核概念车浮游体(以下简称浮游体)外形,并利用三维设计软件SolidWorks建立了其三维几何模型。在此基础上,对几何模型进行简化处理,建立了浮游体流体动力学计算模型。利用流体动力学仿真分析软件ANSYS CFX,采用雷诺时均算法(RANS算法)和两方程的k-ε湍流模型,得到了不同工况的阻力数据。采用Matlab曲线拟合功能,研究了浮游体阻力特性,验证了外形设计方案的可行性。 相似文献