大同--运城高速公路某软基复合地基检测结果分析

以山西大运高速公路某段软基处理为例,从挤密碎石桩的加固机理和破坏方式入手,通过对软基复合地基的原位测试结果分析,得出碎石桩不但提高了地基的承载力,增加了桩间土的强度,减少了地基沉降,而且消除或减轻了地基的液化,使复合地基承载力达到了设计要求,特别是为以后在高速公路修筑中的软基处理提供了参考资料.     

秦巴山区软岩地基桥桩承载性状试验研究

为了研究软岩地基桥桩的荷载传递性状、破坏机理,并获取在该地质条件下更为可靠的桩基计算参数,对秦巴山区软岩地基3根钻孔灌注试桩进行竖向静载试验.结果表明:秦巴山区软岩地基桥桩试桩荷载沉降曲线呈陡降型,实测竖向极限承载力为20500kN,桩的破坏方式为桩身材料强度破坏;淤泥质亚黏土地层中的碎石起到一定的骨架作用,增强了此地层桩极限侧阻力,发挥极限侧阻力所需的桩土(岩)相对位移为4~8mm;强风化砾岩表现为加工软化型,发挥极限侧阻力所需的桩土(岩)相对位移为3~8mm;中风化砂砾岩表现为明显的加工硬化型,所需的桩岩相对位移大,且桩极限侧阻力的特征点不明显;淤泥质亚黏土地层桩侧阻力占总荷载的60%~70%,随着桩顶荷载的逐步加大,该地层桩侧阻力所占比例不断下降,而嵌岩段桩侧阻力所占比例逐渐上升,达到55%~65%,嵌岩段桩侧阻力沿桩深的分布曲线表现出非线性的特征;试桩为端承摩擦桩,桩端阻力约占桩顶荷载的20%左右,且未充分发挥,在上部结构允许的沉降范围内,适当增加桩端的沉降有利于端阻力的发挥;桩侧阻力先于端阻力发挥,建议单桩承载力设计时分别采用不同的端阻力和侧阻力安全系数.     

热-力耦合作用下能源群桩工作特性的数值模拟

为研究能源群桩工作特性,基于Abaqus有限元模拟,将换热稳定阶段的平均温度赋予桩体进行稳态热-力耦合计算,提出了能源群桩承载特性的简化分析方法,并通过与现场数据的对比分析,验证了该研究方法的可行性。结合算例,进一步利用该方法对纯力学荷载和热-力耦合作用下的能源群桩的承载特性进行了分析。结果表明:①群桩基础中能源桩分散对称分布的不均匀沉降要明显小于集中分布,而且分布形式对桩基结构响应特征影响较大;②桩基等刚度下,增大桩径和减小桩间距,群桩倾斜控制效果较好。研究成果可以为能源群桩的工程应用提供一定的参考。      

局部桩筏基础的设计与施工

以加拿大多伦多市某工程为例,介绍了在复杂地质条件下采用局部桩筏基础(PPRF)的设计及施工问题;探讨了设计PPRF的决定性因素;在保持PPRF设计的完整性前提下,提出了单位沉降量的准则,并用于筏板和桩的设计;计算了PPRF的滑移及转动;最后,采用有效方法对该工程采用的局部桩筏基础进行了计算分析.结果表明,PPRF的设计主要取决于侧向土压力、分布不均的建筑荷载以及地基土的非均匀承载力,工程桩应主要布置在沉降较大的区域,即位于筏板基础承受高压力而土体承载力较低的西北部.探讨局部桩筏基础的设计与施工为该类型工程的基础设计提供了一个新的解决途径.     

层状地基中桩的轴向静载沉降特性

采用双折线荷载传递函数,根据桩在竖向静载下的荷载分布与传递规律,运用功的互等定律,导出了一组确定层状地基中桩的轴向荷载沉降曲线的解析简化递推算式,可根据桩侧介质的分布情况和桩的形状对桩进行沉降分析模拟,能较精确确定桩的轴向静载沉降曲线,同时推导了桩顶刚度系数的迭代公式,以此为基础可确定桩的承载力。结合运用实例进行了论证,说明了方法的有效性和正确性。     

盾构施工对既有建(构)筑地基承载力影响及加固土体稳定性分析

针对目前盾构施工既有建（构）筑地基加固依靠经验,缺乏完善理论作为支撑的现象,有必要研究盾构掘进中、离开后既有建（构）筑地基承载力影响机理及加固后土体稳定性。为了解水泥土加固体的受剪工作状态,开展水泥土三轴试验,结果表明,当偏应力达到屈服之前,（σ₁-σ₃）-ε₁关系近似直线,应变很小,且加固体与未加固土抗剪强度相差甚远,稳定性分析时,不考虑加固体位移及其外侧未加固土对剪力的分担。盾构掘进中,其周围土体受到挤压产生的剪应力,扩散至桩侧形成附加正摩阻力,基桩承载力提高;盾构离开后土体卸荷,桩侧产生负摩阻力,基桩承载力降低。盾构施工中加固体上段内侧受被动或主动土压力,外侧及下段受静止土压力,土压力差产生剪应力,潜在滑动界面产生拉、压应力,并导出加固后土体复合滑动面安全系数公式,通过工程实例验算加固体强度及加固后土体的稳定性。      

Theoretical Analysis of Bearing Capacity of Shallowly Embeded Rectangular Footing of Marine Structures

In this paper, the finite element analysis software ABAQUS is used to analyze the ultimate bearing capacity of three-dimensional rectangular footing of marine structures. The deformation law and the failure mode of homogeneous seabed soil beneath the rectangular footing are analyzed in detail. According to the equivalent plastic strain of soil under rectangular footing, an allowable velocity field of homogeneous seabed soil is reasonably constructed. Based on the plastic limit analysis theory of soil mass and by using the Mohr-Coulomb yield criterion, an upper bound solution of the ultimate bearing capacity of three-dimensional rectangular footing on general homogeneous seabed soil is derived, and a correction factor of ultimate bearing capacity of three-dimensional rectangular footing is given. To verify the rationality and applicability of this theoretical solution, some numerical solutions are achieved using the general-purpose FEM analysis package ABAQUS, and comparisons are made among the derived upper bound solution, the solution of Vesic, and the solution of Salgado et al. The results indicate that the upper bound solution of the three-dimensional shallowly embedded rectangular footing proposed in this paper is accurate in calculating the bearing capacity of homogeneous seabed soil. For undrained saturated clay foundation and sandy foundation with smaller internal friction angle, this upper bound solution can evaluate the ultimate bearing capacity of rectangular footing; with the gradual increase of the internal friction angle of the soil, the ultimate bearing capacity of the proposed upper bound solution is slightly higher than that of the rectangular footing.     

干振碎石桩复合地基处理及其效果

干振碎石桩是处理松软地基土的一种行之有效的方法，它是挤密桩的一种。新乡市地方铁路处仓库场地经干振碎石桩地基处理后，桩间土密实度有明显的提高，液化指数大幅度降低，复合地基承载力相应提高，满足了设计要求。     

水泥粉体深层喷射搅拌桩复合地基处理及其效果

水泥粉体深层喷射搅拌桩与干振碎石桩〔１〕、干振灰土桩等一样,也是处理松软地基土的一种有效方法。但与干振碎石桩等其他挤密型复合地基处理方法不同,水泥粉体深层喷射搅拌桩属于摩擦桩型。由于天然地基土对桩体的侧摩擦力和端阻力的共同作用,使复合地基的承载力大幅度提高。然而人们普遍认为,水泥粉体深层喷射搅拌桩法复合地基处理不能解决场地土的液化问题。本文通过工程实例和瑞雷波检测结果,证实了该方法处理的复合地基,除了承载力有较大幅度的提高外,地基土的抗液化能力也可以得到相应的加强。     

振冲碎石桩在加固砂性土地基中的应用

本文介绍在杭州市钱江水厂一期工程中，采用振冲碎石桩加固处理砂性土地基，既提高了地基的抗液化能力，又提高了复合地基承载力，取得了良好的效果，并在该水厂建设的后续工程中得到推广应用。     

Study on deformation law of circular foundation under combined loading

The foundations of some ocean engineering structures are built to withstand not only the vertical gravity load V, but also the horizontal load H induced by sea waves and current. The horizontal load includes the concentrated force load, the moment load M, and the torque load T termed also as combined loading. It is of academic and engineering significance to study the deformation law of submarine seabed due to combined loading. On the basis of the three-dimensional elastic mechanics solution of circular foundation, numerical methods are used to analyze the deformation law of submarine soil under circular foundation with six degrees of freedom. The finite element analysis results give the elastic deformation law of soil in three dimensional spaces, modify the theoretical elasticity solution, and presents nonlinear soil deformation mechanism under the circular foundation with six degrees of freedom.     

田湾核电站某工程偏移基桩性状分析

用低应变动测法检测基桩结构完整性，其测试结果是可靠的，但在田湾核电站某子项用低应变对因滑坡而倾斜的基桩进行检测时，却发现同样是偏移较大的基桩，有的基桩断裂、破损，有的完整，从低应变测试结果很难与实际情况统一起来。考虑到基桩不是孤立的，是与地基土结合在一起的，通过利用基坑支护理论及滑坡形成的圆弧滑动面原理，并结合施工的一些实际情况，从理论上分析了滑坡后基桩断裂、破损、倾斜的可能性，从而对偏移基桩性状做出了正确判断，为工程桩的处理提供依据。     

振冲碎石桩处理黄土地基的效果分析

振冲碎石桩在不同的地基中有不同的作用,本文就某热电厂工程中用振冲碎石桩处理湿陷性黄土地基,消除地基的湿陷性;处理饱和(软)黄土地基,提高其承载能力,以及用振冲桩消除地基中饱和粉细砂的振动液化等效果,用试验和理论计算加以分析和讨论。     

用素土桩挤密法处理陇东湿陷性黄土地基

素土桩挤密地基由桩间挤密土和回填素土夯实的桩体组成，它是一种人工“复合地基”。其作用是通过素土桩挤密法提高地基土的密实度，从而对湿陷性黄土达到消除浅部或深部的部分或全部湿陷性的作用，并改善地基承载能力，减少地基变形。本文通过现场单桩、群桩单元体轻便触探、小环刀深层取样、开剖取样等方法对场地地基土挤密前、后干重度和压实系数进行了对比分析，判定用素土桩挤密法处理陇东湿陷性黄土地基的可行性。     

Elastic-plastic analysis for pile-anchor supporting system of deep foundation pit

By using numerical analysis methods to simulate the deep excavation, a lot of analyses are established on the basis of two-dimensional plane strain, ignoring the fact that foundation pit possesses three dimensions. For soil constitutive relation, people always take linear and nonlinear model, without considering the plastic behavior of soil. Using plastic-elastic hardening model to simulate constitutive relation of soil characteristics, the authors carried out mechanical analysis for pit excavation and support. The results show that the analysis for the stress state of pile anchor system is an effective way which provides theoretical basis for calculation of soil displacement.     

A theoretical analysis of the bearing performance of vertically loaded large-diameter pipe pile groups

This paper aims to present a theoretical method to study the bearing performance of vertically loaded large-diameter pipe pile groups. The interactions between group piles result in different bearing performance of both a single pile and pile groups. Considering the pile group effect and the skin friction from both outer and inner soils, an analytical solution is developed to calculate the settlement and axial force in large-diameter pipe pile groups. The analytical solution was verified by centrifuge and field testing results. An extensive parametric analysis was performed to study the bearing performance of the pipe pile groups. The results reveal that the axial forces in group piles are not the same. The larger the distance from central pile, the larger the axial force. The axial force in the central pile is the smallest, while that in corner piles is the largest. The axial force on the top of the corner piles decreases while that in the central pile increases with increasing of pile spacing and decreasing of pile length. The axial force in side piles varies little with the variations of pile spacing, pile length, and shear modulus of the soil and is approximately equal to the average load shared by one pile. For a pile group, the larger the pile length is, the larger the influence radius is. As a result, the pile group effect is more apparent for a larger pile length. The settlement of pile groups decreases with increasing of the pile number in the group and the shear modulus of the underlying soil.     

多层锚固镶嵌混凝土钢管桩在岩溶地基的应用

岩溶地区基建地基工程的设计与施工难度较大,文章介绍应用多层锚固镶嵌压力灌浆混凝土钢管桩来提高地基综合承载力,在典型工程取得经验,展示该技术方法的运用前景     

成层土中轴横受荷桩水平响应的非线性解

对于承受轴向荷载的水平受荷桩，以往研究大多基于线弹性或弹塑性水平荷载传递模型。为提升轴横受荷桩的计算设计水平，采用轴向荷载传递法计算桩身轴力，考虑桩身轴力引起的P-Δ效应，基于双曲线型水平荷载传递模型考虑桩-土体系变形的非线性特征，对成层土中轴横受荷桩的水平响应进行分析求解，得到了轴横荷载作用下桩身变形和内力的非线性有限差分解，并采用MATLAB语言编制了计算程序。使用模型试验算例与基于现场试验的有限元算例对非线性解的准确性进行对比验证，结果表明:计算结果与算例数据吻合良好，可靠性较高；采用不同荷载传递模型的计算结果在不同荷载水平下有所差异，在较大荷载水平下桩-土变形的非线性特点不容忽视。      

Application of FLAC3D in supporting engineering of deep foundation ditch

Based on the design principles of economic rationality and safety, multiple-pivot pile anchorage approach was used as the supporting engineering of a tall building with a deep foundation ditch. The designs, such as anchor arm, single pile and the whole, were set up in accordance with the calculations of the internal force from the equivalent beam and Yamagata Kunio methods. Moreover, the rationality of the design was estimated using the stability checks. FLAC3D was used for calculating the accuracy of the design. Using FLAC3D to simulating ditch cutting and supporting processes can obtain the equivalent results as the theory analysis in the displacement of ditch surrounding wall, the stress field and stress distribution.     

Analysis of raft foundation design based on considering influence of superstructure stiffness

The finite element method was used for analysis of raft foundation design in high-rise building. Compared with other conventional methods, this method is more adapted to the practical condition since both superstructure stiffness and soil conditions were considered in calculation. The calculation results by example show that the base reaction is more uniform and the maximum reaction decreases obviously. Accordingly, the raft foundation design is more economic without any loss of security for high-rise building.