High-Speed Ring Shear Tests to Study the Motion and Acceleration Processes of the Yingong Landslide

In this paper, the motion and acceleration process, as well as the mechanism of a high speed and long run landslide are investigated by adopting high speed ring shear test and taking the landslide occurred at Yigong River in Bomi, Tibet on April 9, 2000 as the background. According to the motion characteristics of high-speed and long distance motion landside, the mechanism is studied under different conditions such as shear speed, consolidated drained and consolidated undrained status. Results show that high speed shearing process hinders and delays the dissipation of pore pressure, and drives pore water migrating to shear zone slowly. Both of water content and fine particle content at shear zone are obviously higher than those in other layers; and soil liquefaction occurs at shear zone in the saturated consolidated undrained ring shear tests. The effective internal friction angle of the consolidated undrained soil is much lower than that of the consolidated drained soil under ring shearing. The results also indicate that the shearing speed affecting the strength of soil to some extent. The higher the ring shearing speed is, the lower the strength of soil is. This investigation provides a preliminary interpretation of the mechanism of the motion and acceleration process of the Yigong landslide, occurred in Tibet in 2000.     

冲击作用下饱和土性状的试验研究

在三轴条件下,对饱和土(砂土和黏土)进行排水与不排水条件下的冲击试验及冲击后再固结试验,对比研究了不同渗透性土在不同排水条件下的冲击动力响应和冲击后再固结性状.结果表明:饱和黏土不排水冲击时的孔隙水压力随冲击击数增加而升高并逐渐稳定,排水冲击时的孔隙水压力则是先达到峰值然后有所下降;砂土不排水冲击时的冲击能量对孔隙水压力影响最明显;饱和砂土不排水冲击时的轴向应变与冲击击数呈近似线性关系,饱和黏土冲击及饱和砂土排水冲击则呈近二次曲线关系;饱和砂土不排水冲击后再固结阶段的孔隙水压力立即消散为0,同时体变迅速增大到一定值;饱和黏土在冲击后再固结阶段的孔隙水压力在一定时间内逐渐消散完毕,同时体变逐渐增大;饱和黏土排水冲击时,冲击阶段产生的体变占冲击引起总体变的39%~49%,冲击后再固结阶段产生的体变占51%~61%;砂土和黏土的总体变均表现为排水冲击明显大于不排水冲击,改善冲击时的排水条件有利于提高加固效果.     

Shear strength features of soils developed from purple clay rock and containing less than two-millimeter rock fragments

Soil shear strength is an important indicator of engineering design and an essential parameter of soil precision tillage and agricultural machinery and equipment design. Although numerous studies have investigated the characteristics of different soil shear strengths, only a few of these works have paid attention to soils containing considerable quantities of rock fragments. To date, most studies on the effects of rock fragments on the shear strength have paid attention to the role of rock fragments with sizes >2 mm. The effects of rock fragments <2 mm in soil are generally ignored. Similar to rock fragments >2 mm, the presence of rock fragments <2 mm could also change the mechanical properties of soils. Thus, in the present study we evaluated the potential influence of <2 mm rock fragments on soil shear strength via an unconsolidated undrained (UU) triaxial compression test. Our results were as follows: (1) A certain quantity of <2 mm rock fragments presented in purple soils developed from clay rocks; and an appropriate quantity of <2 mm rock fragments could improve the shear strength of soils. (2) The different PSDs of soils containing <2 mm rock fragments mainly caused variations in the internal friction angle of soils. (3) The shear strengths of the two mudstone-developed red-brown and gray-brown purple soils was more sensitive to water than that of the shale-developed coarse-dark purple soil. As the soil water content increased from 9% to 23%, the changes in the cohesion, internal friction angle, shear strength, and the maximum principal stress difference were smaller in the coarse dark purple soil than in the two other soils. We therefore concluded that <2 mm rock fragments in purple soils exerted important effects on soil shear strength. A better understanding of the differences among the shear strength features of purple soils could help improve the design of agricultural machinery and equipment.     

An experimental study on the wave-induced pore water pressure change and relative influencing factors in the silty seabed

In this study, a flume experiment was designed to investigate the characteristics of wave-induced pore water pressure in the soil of a silty seabed with different clay contents, soil layer buried depths and wave heights respectively. The study showed that water waves propagating over silty seabed can induce significant change of pore water pressure, and the amplitude of pore pressure depends on depth of buried soil layer, clay content and wave height, which are considered as the three influencing factors for pore water pressure change. The pressure will attenuate according to exponential law with increase of soil layer buried depth, and the attenuation being more rapid in those soil layers with higher clay content and greater wave height. The pore pressure in silty seabed increases rapidly in the initial stage of wave action, then decreases gradually to a stable value, depending on the depth of buried soil layer, clay content and wave height. The peak value of pore pressure will increase if clay content or depth of buried soil layer decreases, or wave height increases. The analysis indicated that these soils with 5% clay content and waves with higher wave height produce instability in bed easier, and that the wave energy is mostly dissipated near the surface of soils and 5% clay content in soils can prevent pore pressure from dissipating immediately.     

Mechanisms involved in triggering debris flows within a cohesive gravel soil mass on a slope: a case in SW China

The triggering mechanisms of debris flows were explored in the field using artificial rainfall experiments in two gullies, Dawazi Gully and Aizi Gully, in Yunnan and Sichuan Provinces, China, respectively. The soils at both sites are bare, loose and cohesive gravel-dominated. The results of a direct shear test, rheological test and back-analysis using soil mass stability calculations indicate that the mechanisms responsible for triggering debris flows involved the decreases in static and dynamic resistance of the soil. The triggering processes can be divided into 7 stages: rainfall infiltration, generation of excess runoff, high pore water pressure, surface erosion, soil creep, soil slipping, debris flow triggering and debris flow increment. In addition, two critical steps are evident: (i) During the process of the soil mass changing from a static to a mobile state, its cohesion decreased sharply (e.g., the cohesion of the soil mass in Dawazi Gully decreased from 0.520 to 0.090 kPa, a decrease of 83%). This would have reduced the soil strength and the kinetic energy during slipping, eventually triggered the debris flow. (ii) When the soil mass began to slip, the velocity and the volume increment of the debris flow fluctuated as a result of the interaction of soil resistance and the sliding force. The displaced soil mass from the source area of the slope resulted in the deposition of a volume of soil more than 7 - 8 times greater than that in the source area.     

Geomorphologic analysis and physico-dynamic characteristics of Zhatai-Gully debris flows in SW China

Zhatai gully is a typical debris flow channel in Butuo county of Sichuan province, southwestern China. The geomorphologic features are analyzed and the physical-dynamic characteristics are discussed on the basis of field investigation and laboratory tests. Geomorphologic analysis indicates that Zhatai-gully drainage in relation to debris flow can be divided into source area, transport area, and deposition area. The source area has a steep slope and has very limited vegetation cover, which favors runoff, allowing loose solid materials to be mobilized easily and rapidly. In the transport area, there are many small landslides, lateral lobes, and loose materials distributed on both banks. These landslides are active and constantly providing abundant source of soils for the debris flows. In the deposition area, three old debris-flow deposits of different ages can be observed. The dynamic calculation shows that within the recurrence intervals of 50 and 100 years, debris flow discharges are 155.77m³/s and 1y8.19m³/s and deposition volumes are 16.39 x 10⁴ m³ and 18.14 x 10⁴ m³, respectively. The depositional fan of an old debris flow in the outlet of the gully can be subdivided into six layers. There are three debris flow deposits on left and two on the right side of the gully. Grain-size tests of sediments from the soil, gulley bed deposits, and the fresh and old debris flow deposits showed that high amounts of clay and fine gravel were derived from the soil in the source area whereas much of the gravel fraction were sourced from the gully bed deposits. Comprehensive analysis indicates that Zhatai gully is viscous debris-flow gully with moderate to high frequency and moderate to large magnitude debris flows. The risk of a debris flow disaster in Zhatai-gully is moderate and poses a potential threat to the planned hydroelectric dam. Appropriate engineering measures are suggested in the construction and protection of the planned hydroelectric station.     

融雪条件下新疆伊犁谷地黄土-卵砾石接触面残余强度

为研究融雪作用下黄土-卵砾石接触面残余强度,以新疆伊犁谷地某黄土-卵砾石接触面滑坡为例,通过自制模具,制作黄土-卵砾石接触面环剪试样,开展不同含水率黄土-卵砾石接触面环剪试验,并通过扫描电镜（SEM）,从微观结构角度探究水对黄土-卵砾石接触面残余强度的影响。试验结果表明:黄土-卵砾石接触面抗剪强度随着含水率的增加而减小,剪切过程中存在应变软化现象,随着正应力及含水量的增加,应变软化现象越不明显;黄土-卵砾石接触面残余强度随着法向应力的增大而增大,且存在较好的线性关系,符合摩尔库伦强度准则;黄土-卵砾石接触面残余强度参数随着含水率的增加而降低,以含水率w=18%为界（塑限含水率19.1%附近）,当含水率为10%~18%时,残余内摩擦角φ_r变化较小（Δφ_r=5.4°）,当含水率为18%~26%时,残余内摩擦角φ_r变化较大（Δφ_r=9.0°）;微观结构方面,随着含水率的增加,黄土-卵砾石接触面形成软化"泥膜",部分填充了卵砾石凹凸部分,剪切面较为光滑,在剪切过程中,黏粒更加分散,附着在黄土颗粒表面,部分填充孔隙,起润滑作用,降低了残余强度。本文的研究成果可以为新疆伊犁谷地黄土-卵砾石接触面型滑坡形成机理研究及工程防治提供科学参考。      

降雨模式对震后泥石流起动模式影响的试验研究: 以九寨天堂沟为例

降雨过程中降雨强度的变化会影响土体渗透率及饱和过程, 从而改变土体的力学性质, 影响泥石流起动模式及破坏规模。为探究不同降雨模式对震后泥石流起动机制的影响, 自制了小比例模型槽, 结合可控雨型的降雨模拟系统, 进行了人工降雨诱发泥石流的室内模型试验; 基于不同降雨模式下泥石流的起动过程分析, 对坡体内部含水率和孔隙水压力的变化规律进行了研究。研究结果表明: 递增型降雨模式下泥石流发生突然, 呈整体滑坡转化为泥石流起动模式, 坡体破坏规模最大; 递减型降雨模式下表现为后退式溃散失稳起动模式; 均匀型降雨模式下则表现为溯源侵蚀起动模式; 中峰型降雨模式下以局部滑坡转化为泥石流起动模式; Ⅴ型降雨模式下则由坡面侵蚀加剧转化为泥石流启动模式, 破坏规模最小。研究结果可以为九寨沟地区泥石流的预报预警提供参考。      

Identification of potential sites of debris flows in the upper Min River drainage,following environmental changes caused by the Wenchuan earthquake

The Wenchuan earthquake caused numerous landslides and collapses that provide abundant unconsolidated material for future mobilization as debris flows.Debris flows will be very active and cause considerable damage for some time in the affected area.Because of environmental changes related to the earthquake,many potentially dangerous debris flow gullies have yet to be identified.This paper selects the upper Min River from Yinxiu to Wenchuan as the study area,interprets the unconsolidated deposits,and discusses their relationship to distance from the fault.Then,applying that information and the values of other factors relating to debris flow occurrence,the locations of potential debris flows are analyzed by multi-factor comprehensive identification and rapid identification.The multi-factor comprehensive identification employs fuzzy matter-element extension theory.The volume of unconsolidated material in the study area is about 3.28 × 108 m3.According to the analysis by multi-factor comprehensive identification,47 gullies have a high probability for potential debris flow,8 gullies have a moderate probability,and 1 gully has a low probability.     

Influences of soil moisture and salt content on loess shear strength in the Xining Basin,northeastern Qinghai-Tibet Plateau

Moisture and salt content of soil are the two predominant factors influencing its shear strength. This study aims to investigate the effects of these two factors on shear strength behavior of loess in the Xining Basin of Northeast Qinghai-Tibet Plateau, where such geological hazards as soil erosion, landslides collapse and debris flows are widespread due to the highly erodible loess. Salinized loess soil collected from the test site was desalinized through salt-leaching in the laboratory. The desalinized and oven-dried loess samples were also artificially moisturized and salinized in order to examine how soil salinity affects its shear strength at different moisture levels. Soil samples prepared in different ways(moisturizing, salt-leaching, and salinized) were measured to determine soil cohesion and internal friction angle. The results show that salt-leaching up to 18 rounds almost completely removed the salt content and considerably changed the physical components of loess, but the soil type remained unchanged. As salt content increases from 0.00% to 12.00%, both the cohesion and internal friction angle exhibit an initial decrease and then increase with salt content. As moisture content is 12.00%, the salt content threshold value for both cohesion and internal friction angle is identified as 3.00%. As the moisture content rises to 16.0% and 20.00%, the salt content threshold value for cohesion is still 6.00%, but 3.00% for internal friction angle. At these thresholds soil shear strength is the lowest, below which it is inversely related to soil salinity. Beyond the thresholds, however, the relationship is positive. Dissimilar to salinity, soil moisture content exerts an adverse effect on shear strength of loess. The findings of this study can provide a valuable guidance on stabilizing the engineering properties of salinized loess to prevent slope failures during heavy rainfall events.     

Experimental analysis for the dynamic initiation mechanism of debris flows

Debris flow is one of the major secondary mountain hazards following the earthquake. This study explores the dynamic initiation mechanism of debris flows based on the strength reduction of soils through static and dynamic triaxial tests. A series of static and dynamic triaxial tests were conducted on samples in the lab. The samples were prepared according to different grain size distribution, degree of saturation and earthquake magnitudes. The relations of dynamic shear strength, degree of saturation, and number of cycles are summarized through analyzing experimental results. The findings show that the gravelly soil with a wide and continuous gradation has a critical degree of saturation of approximately 87%, above which debris flows will be triggered by rainfall, while the debris flow will be triggered at a critical degree of saturation of about 73% under the effect of rainfall and earthquake(M>6.5). Debris flow initiation is developed in the humidification process, and the earthquake provides energy for triggering debris flows. Debris flows are more likely to be triggered at the relatively low saturation under dynamic loading than under static loading. The resistance of debris flow triggering relies more on internal frication angle than soil cohesion under the effect of rainfall and earthquake. The conclusions provide an experimental analysis method for dynamic initiation mechanism of debris flows.     

Spudcan Penetration Simulation Using the Coupled Eulerian-Lagrangian Method with Thermo-Mechanical Coupled Analysis

A novel modeling technique based on the coupled Eulerian-Lagrangian(CEL) method is provided to solve the geotechnical problems with large deformations. The technique is intended to solve the update problem of soil mechanical properties during spudcan penetration in normally consolidated clay soil. In the CEL model, the normal method of assigning an increasing shear strength profile with depth(NA) is defective due to its Eulerian framework. In this paper, a new technique is proposed to update soil material properties by introducing thermo-mechanical coupled analysis(TMCA) to the CEL models. During establishment of the CEL models, the optimal penetration velocity and minimum mesh size are determined through parametric studies. Reasonability and accuracy are then verified through comparison of the preliminary results with the soil flow configuration and penetration resistance(Fv) of a centrifuge test, and the results of the proposed method are compared with those of the remeshing and interpolation technique with small strain(RITSS) method. To achieve a CEL model with satisfactory accuracy, the NA and TMCA methods implemented in the CEL models and the RITSS method are first adopted in weightless soil. Comparison of the findings with those obtained in previous studies shows that the TMCA method can update material properties and predict Fv. The TMCA method is then applied to soils with self-weight and different shear strength profiles. Results show that the proposed method is capable of accurately modeling the large deformation problem of spudcan penetration in non-homogeneous clay.     

浸泡作用下碎石土剪切强度衰减规律及机理

水库蓄水后, 滑坡体碎石土经受长时期的浸泡, 力学性质发生改变, 从而影响滑坡整体稳定性。为探究浸泡对碎石土力学性质的影响规律, 选取三峡库区马家沟滑坡后缘未经受长期浸泡作用的碎石土进行大型直剪试验, 分析了不同浸泡天数下碎石土的剪切力学性质。试验结果表明: 浸泡40 d后, 碎石土黏聚力下降幅度达39%, 内摩擦角下降幅度为8.3%;碎石土黏聚力在浸泡前期快速下降, 下降速率随浸泡天数增加而降低, 浸泡20 d后, 黏聚力基本达到稳定。为探究碎石土抗剪强度降低的原因和机理, 对粉质黏土(碎石土细粒成分)进行了三轴剪切试验、激光粒度分析及浸出液阳离子分析等试验, 揭示了碎石土抗剪强度的衰减机理为: 浸泡作用下, 碎石土中的粉质黏土发生矿物溶解、离子交换与吸附作用, 土体中大颗粒细化, 胶结作用减弱, 进而导致碎石土整体抗剪强度降低。研究结果对库区碎石土滑坡评价与治理具有一定的指导意义。      

降雨作用下青石镇政府后山堆积层滑坡渗流与稳定性

以黄冈地区青石镇政府后山堆积层滑坡为例，在分析了其工程地质特征及地质结构特征的基础上，采用有限元法研究了非饱和土瞬态体积含水量及孔隙水压力的分布，采用考虑孔隙水压力的Janbu法分析计算了降雨对堆积层滑坡安全系数的影响。研究结果表明:①降雨入渗导致坡体孔隙水压力升高，滑面抗剪强度降低，安全系数也随之逐渐降低，其中在降雨前期，两侧的抗剪强度下降速率比中部快，而到了后期中部的抗剪强度下降速率明显快于两侧；②安全系数变化表现为前19 d以0.008/d的速率缓慢下降，19~30 d以0.03/d的速率缓慢下降，30 d以后下降速度降低，至36 d之后不再发生变化，其中在0~11 d两侧抗剪强度变化对滑坡整体稳定性变化的贡献比中部大，19~36 d中部抗剪强度变化对滑坡整体稳定性变化的贡献要比两侧大；③降雨入渗过程中，地下水从坡体表层和两侧流向坡体中部，负孔压区面积向中部不断压缩，中部地下水变化受到两侧及上层的制约，体积含水量及孔隙水压力变化相对滞后；④该滑坡的防治重点是做好降雨前期坡体后缘地下水截流以及前缘地下水排泄工作，同时，做好地表排水，减少降雨入渗。      

塔中地区顺9井区柯坪塔格组黏土膜成因及其油气地质意义

为寻觅致密砂岩储层中发育的优质储层提供理论依据,分析铸体薄片鉴定、扫描电镜资料、结合压汞及物性资料.结果表明:塔里木盆地塔中顺9井区志留系柯坪塔格组沥青砂岩中发育的黏土矿物薄膜形成于成岩早期(同生成岩期),以自生式为主,含少量原生式黏土膜;黏土膜的发育与分布受到沉积作用、成岩环境及成岩温压系统的共同控制,早成岩期(同生期)发育的黏土膜在中—低压实强度下对储层的孔隙保护具有一定的建设性作用,因其占据一定的孔喉空间,又降低储层的渗透率,随着埋深增大,黏土膜矿物成分也逐渐向伊利石转化并分布在孔隙中,伊利石赋存状态也由蜂窝状变为毛发状、丝网状及搭桥状,分割甚至堵塞孔隙,使得储层砂体渗透率大幅度降低;沉积环境中的沉积微相对黏土膜发育与分布的控制体现在中—下临滨微相中黏土膜较为常见,而在上临滨—前临滨微相中,因水体的淘洗降低储层砂体中的泥质含量,黏土膜不发育,储层砂体中的黏土膜含量制约储层质量,发育黏土膜的井段储层孔隙度大于不发育黏土膜的井段,黏土膜含量在0.5%～5.0%井段的储层孔隙度要好于黏土膜含量超过5.0%井段的.     

Comparison of Rheometric Devices for Measuring the Rheological Parameters of Debris Flow Slurry

Soil samples with clay content ranging from 15% to 31%, were taken from three debris flow gullies in Southwest China. Three debris flow slurry samples were prepared and tested with four measuring systems of an Anton Paar Physica MCR301 rheometer, including the concentric cylinder system,the parallel-plate system, the vane geometry, and the ball measuring system. All systems were smoothwalled. Flow curves were plotted and yield stress was determined using the Herschel-Bulkley model,showing differences among the different systems.Flow curves from the concentric cylinder and parallelplate systems involved two distinct regions, the low shear and the high shear regions. Yield stresses determined by data fitting in the low shear region were significantly lower than the values from the inclined channel test which is a practical method for determining yield stress. Flow curves in the high shear region are close to those from the vane geometry and the ball measuring system. The fitted values of yield stress are comparable to the values from the inclined channel test. The differences are caused by wall-slip effects in the low shear region.Vane geometry can capture the stress overshoot phenomenon caused by the destruction of slurry structure, whereas end effects should be considered in the determination of yield stress. The ball measuring system can give reasonable results, and it is applicable for rheological testing of debris flow slurries.     

Cyclic Shearing Deformation Behavior of Saturated Clays

The apparatus for static and dynamic universal triaxial and torsional shear soil testing is employed to perform stress-controlled cyclic single-direction torsional shear tests and two-direction coupled shear tests under unconsolidated-undrained conditions. Through a series of tests on saturated clay, the effects of initial shear stress and stress reversal on the clay’s strain-stress behavior are examined, and the behavior of pore water pressure is studied. The experimental results indicate that the patterns of stress-strain relations are distinctly influenced by the initial shear stress in the cyclic single-direction shear tests. When the initial shear stress is large and no stress reversal occurs, the predominant deformation behavior is characterized by an accumulative effect. When the initial shear stress is zero and symmetrical cyclic stress occurs, the predominant deformation behavior is characterized by a cyclic effect. The pore water pressure fluctuates around the confining pressure with the increase of cycle number. It seems that the fluctuating amplitude increases with the increase of the cyclic stress. But a buildup of pore water pressure does not occur. The de- formations of clay samples under the complex initial and the cyclic coupled stress conditions include the normal deviatoric deforma- tion and horizontal shear deformation, the average deformation and cyclic deformation. A general strain failure criterion taking into account these deformations is recommended and is proved more stable and suitable compared to the strain failure criteria currently used.     

Grain size distribution of soils within the Cordillera Blanca,Peru: An indicator of basic mechanical properties for slope stability evaluation

This paper presents results of a study on the mechanical properties of sandy and gravely soils within the Cordillera Blanca, Peru. The soils were divided into groups according to their origin （glacial, fluvial, or debris flow）. The grain size distribution of forty three soil samples was used to classify the soils according to the scheme of the Unified Soil Classification System （USCS）. These distributions have then been used to estimate shear strength and hydraulic properties of the soils. There are clear differences between the soils which reflect their divergent origins. The glacial soils normally fit within one of two distinctive groups according to the proportion of fines （Group A, 7%-21.5%; Group B, 21%-65%）. The estimation of shear strength at constant volume friction angle and peak shear strength of the glacial sediments with low content of fines was made using published data relating to the measured shear strength characteristics of soils with similar origins and grain size distributions. The estimated values were supported by measurements of the angle of repose taken from fourteen samples from two moraines and by shear tests on samples from one locality. The results of the grain size distribution werealso used to estimate the average hydraulic conductivity using the empirical Hazen formula which results were verified by field infiltration tests at two localities.     

Effects of loose deposits on debris flow processes in the Aizi Valley,southwest China

Loose deposits, rainfall and topography are three key factors that triggering debris flows.However, few studies have investigated the effects of loose deposits on the whole debris flow process.On June 28, 2012, a catastrophic debris flow occurred in the Aizi Valley, resulting in 40 deaths.The Aizi Valley is located in the Lower Jinsha River,southwestern Sichuan Province, China. The Aizi Valley debris flow has been selected as a case for addressing loose deposits effects on the whole debris flow process through remote sensing, field investigation and field experiments. Remote sensing interpretation and laboratory experiments were used to obtain the distribution and characteristics of the loose deposits, respectively. A field experiment was conducted to explore the mechanics of slope debris flows, and another field investigation was conducted to obtain the processes of debris flow formation, movement and amplification. The results showed that loose deposits preparation, slope debris flow initiation,gully debris flow confluence and valley debris flow amplification were dominated by the loose deposits.Antecedent droughts and earthquake activities may have increased the potential for loose soil sources in the Aizi Valley, which laid the foundation for debris flow formation. Slope debris flow initiated under rainfall, and the increase in the water content as well as the pore water pressure of the loose deposits were the key factors affecting slope failure. The nine gully debris flows converged in the valley, and the peak discharge was amplified 3.3 times due to a blockage and outburst caused by a large boulder. The results may help in predicting and assessing regional debris flows in dry-hot and seismic-prone areas based on loose deposits, especially considering large boulders.     

ECO-ENVIRONMENT CHANGE AND SOIL EROSION PROCESS IN THE RECLAIMED FORESTLAND OF THE LOESS PLATEAU

1INTRODUCTIONSerioussoilerosionhasmadetheeco-environmentfragileintheLoessPlateau.InthemodernsoilerosionoftheLoessPlateau,theman-madeerosionwasthedominanterosionpattern (TANGetal.,1993a,1993b).Manyhumanactivitiesacceleratesoilerosion,butthemostinfluentialactivitiesaretodestroyforestandgrass,eventodestroyallvegetation.Reclamationbydestroyingforestlandandgrasslandartificiallycouldrapidlyincreasesoilerosionintensityinshorttimeandenlargeerosionspacegradually,evenchangeerosiondirectionandwor…