黏土地基上海洋平台桩靴峰值阻力上限分析

在自升式平台的预压载过程中，桩靴在层状地基上较易发生“穿刺”现象，很大程度上影响着平台的安全运行。准确地分析桩靴峰值阻力，避免平台桩靴发生“穿刺”是非常重要的。采用极限分析上限定理，合理构建运动许可速度场，从理论上推导了层状地基上桩靴峰值阻力的上限解答。为了进一步验证峰值阻力理论解答的准确性，采用ABAQUS有限元软件构建了“桩靴—弹塑性海床”的三维数值模型，对桩靴贯入海床的过程进行了数值模拟，分析桩靴周围土体的塑性变形演变规律，研究土体的破坏机理。研究结果表明：推导的桩靴峰值阻力上限解答，能够较好地计算层状地基极限承载能力，通过与离心机试验和数值结果对比，计算误差在18%以内；给出的运动许可速度场能够较好地反映桩靴周围土体破坏模式；桩靴阻力达到峰值时，下层软土中的土塞高度约为桩靴直径的0.2倍。     

黏性土底床中桩基底部吸力试验研究

海洋工程结构物桩基/基础在水下黏性土底床中上拔时,其底部会产生负压,由于负压产生的吸力可一定程度上影响桩基的抗拔力,而对于该力的变化特性目前尚不明确。因此,开展对海工结构物桩基在黏性土底床中上拔时底部吸力的研究具有十分重要的现实意义。通过物理试验,测量了模型桩在黏性土底床垂直上拔过程中底部腔体形态、压力以及拉力的变化情况,分析了上拔速度和埋深比对桩体底部压力的影响。研究结果表明:在黏性土底床中,桩基底部负压吸力对抗拔力有一定影响;桩基上拔时,底部会产生孔隙水腔体,在负压作用下,腔体不断被周围土体回填,使腔体大小保持相对稳定;相同埋深条件下,桩基底部负压随上拔速度增加而增大,但当上拔速度增大到一定值后,其影响不再明显;相同上拔速度情况下,桩基所受负压随埋深的增加而增大。最后提出了计算桩基垂向上拔时底部最大吸力的经验公式,并对公式进行验证。     

基于拔桩能力的自升式平台海外作业优选

针对某海外项目中可能遇到的钻井平台压载后入泥深度过大和拔桩困难的问题,开展平台优选计算。首先搜集了预定作业井位周围井位的地质勘查资料,利用二次插值法进行作业井位地质勘察数据计算,据此计算了桩脚入泥深度,并根据作业平台结构参数计算了平台的拔桩阻力。为解决平台极限拔桩能力小于拔桩阻力的问题,设计了可控冲桩阀和冲桩系统以消除或减小桩靴底部的吸附力、桩靴侧部土体剪切力和桩靴上部土重。最后将平台拔桩能力与最终拔桩阻力进行对比,给出平台推荐结果。     

自升式钻井平台桩靴踩脚印应对措施对比研究

基于现有规范与文献研究提出的减小桩靴踩脚印附加响应的相关措施,首先基于耦合欧拉—拉格朗日(CEL)定量分析了传统纺锤形桩靴与新型桩靴在不同工况条件下插桩时桩靴地基土体相互作用机制,明确了最不利桩靴踩脚印工况时的插桩偏心距与桩坑深度。基于该最不利工况条件,对比分析了新型六孔莲蓬形桩靴、试踩法与地基钻孔法3种桩靴踩脚印应对措施的适用性与有效性。结果表明,相较于传统纺锤形桩靴,采用六孔莲蓬形桩靴使桩靴倾斜角与桩腿偏移距分别降低了33.13%和48.26%,说明结构在位稳定性更高。此外,通过对比分析得出,采用最佳设置方式进行试踩与钻孔处理后再进行桩靴贯入时,桩靴受到的水平滑动力峰值与桩腿RP₁处弯矩峰值相较于未处理时分别降低了29.47%、29.17%、34.7%、37.7%。可见,3种应对措施均能有效降低桩靴踩脚印后产生的不利影响,提高桩靴结构的在位稳定性。以最终减小不利附加响应程度作为评定标准：地基钻孔法>新型六孔莲蓬形桩靴>试踩法,由于地基钻孔法与试踩法均需增设额外机械设备及施工工序,大幅提高了工程造价,因此,在实际工程中,需要根据实际情况恰当选择应对措施。研究成果可为实际工程中应对桩靴踩脚印工况响应提供一定参考与借鉴。     

新型平台桩靴在“砂-黏”地层中穿刺的数值模拟研究

开发了一种新型平台桩靴,可通过活动板转动实现自升式平台不同阶段桩靴受力面积的灵活变化。基于大变形有限元方法,模拟新型桩靴基础在“砂-黏”地层中的贯入过程,分析了活动板转角、砂层厚度比、摩擦角和黏土层不排水抗剪强度对新型桩靴贯入阻力的影响,并与普通桩靴的贯入响应比较。数值分析中,上覆砂土和下层黏土分别采用摩尔库伦模型和修正Tresca模型进行模拟。结果表明：新型桩靴穿刺时,土层参数对峰值阻力的影响规律与普通桩靴相同,但其峰值阻力随活动板转角的变化而变化,无法直接使用具有等效面积普通桩靴的穿刺预测方法。考虑各项关键影响因素,结合穿刺破坏时的地基破坏模式,基于数值模拟结果提出了适用于新型桩靴的贯入阻力预测公式。     

弱超固结黏土中桩靴贯入形成孔洞对承载力影响

自升式平台作业前需对桩靴基础进行预压安装,使桩靴具备抵抗竖向-水平-弯矩复合荷载的能力。安装过程中,桩靴上部将形成一定深度的孔洞。弱超固结黏土地基中,土体强度较高,桩靴最终贯入深度较浅,而形成的上部孔洞较深,因此孔洞将对桩靴就位后的承载力产生影响。通过有限元分析,研究弱超固结黏土中桩靴上部孔洞对承载力的影响,结果表明:1)与无孔洞的情况相比,孔洞的存在对桩靴的单向和复合承载力有削弱作用; 2)当桩靴与孔洞底部距离大于桩靴直径时,承载力不再受上部孔洞的影响; 3)当桩靴埋深小于等于0.75倍桩靴直径时,无论桩靴上部有无孔洞,现有预测公式都不能较为合理地预测弱超固结黏土地基的复合承载力,为此提出了考虑孔洞影响的桩靴复合承载力包络面预测公式。     

自升式钻井平台插桩深度探析

针时目前带桩靴的自升式桩基平台插桩深度计算中存在的问题,通过考虑插桩过程中桩靴对地层物理力学性质的影响,运用最小二乘法求得桩靴对地层承载力的影响系数,从而时Terzaghi和Peck公式进行修正,提高插桩深度预测的准确性.     

胜利六号近海自升式移动钻井平台的插拔桩问题的研究

胜利六号自升式钻井平台在渤海埕北19井施工时,由于插桩过深,造成桩脚起拔困难。这引起了国内外有关专家的普遍关注。本文从分析黄河口地层沉积特征入手,通过对平台单桩承载力、单桩抗拔力的计算,评价胜利六号平台在这一区域施工的可行性。最后对平台桩脚的起拔方法进行讨论。这对该平台今后在这一地区开展工作具有指导性的现实意义。     

抗浮爆扩桩抗拔机理有限元分析

高地下水位地区构筑地下建(构)筑物必须解决结构上浮问题,抵抗上拔荷载作用已成为地下工程建设中经常需要面临的问题。试验表明爆扩桩具有很好的抗浮能力,其成桩施工工艺方面的研究也比较完善,但是对爆扩桩的承载机理的研究很少,通过运用NCAP-1有限元计算程序,分析总结爆扩桩的抗拔承载机理。     

桩靴贯入黏土层时邻近群桩相互作用分析

为研究钻井船插桩对邻近平台群桩相互作用的影响,采用耦合欧拉拉格朗日(CEL)方法对桩靴贯入黏土层时邻近群桩中各桩荷载分担比、桩头附加位移及两桩相互作用系数进行了分析。首先通过对缩尺模型试验的数值分析,验证了CEL方法的可行性;然后进一步分析了桩靴贯入黏土层时对邻近群桩相互作用的影响;最后探讨了净间距、桩间距对群桩相互作用的影响。结果表明,在桩靴贯入中,前桩的荷载分担比大于后桩,且桩靴贯入至一定深度后,当净间距越小或桩间距越大时,前桩的荷载分担比越大、后桩的荷载分担比越小,但各桩的荷载分担比随桩靴贯入深度增加时的变化规律不变;净间距越大,桩头附加位移及相互作用系数越小;在桩靴贯入时,由于受群桩遮拦效应的影响,桩头附加位移及相互作用系数随桩间距的变化规律同插桩前有所不同,当桩间距大于3倍桩径时,随桩间距的增加而减小,当桩间距小于3倍桩径时,随桩间距的增加而增大。     

Behavior of a shallow plate anchor in clay under sustained loading

Laboratory model test results for the uplift of a shallow circular plate anchor embedded in a soft saturated clay are presented. For all tests the bottom of the anchor plate was vented to eliminate the mud suction force. The tests were divided into two categories: (1) short‐term tests to determine the variation of the net ultimate uplift capacity and hence the breakout factor with embedment ratio, and (2) creep tests with sustained uplift loads at varying embedment ratios. Based on the model test results, the variation with time, has been determined for the rate of strain of the soil located above the plate anchor. Empirical relationships for obtaining the rate of anchor uplift have been proposed.     

The influence of pull-out load on the efficiency of jetting during spudcan extraction

Mobile jack-up drilling rigs are deployed at many locations during their service life. This necessitates retrieval of the platform’s legs and spudcan footings before the rig move. In soft soils, where the spudcans embed deeply, the extraction process can be difficult, time consuming and therefore costly. Water jetting systems, devised to ease spudcan extraction, are a common feature on modern jack-up units. However, their effectiveness in reducing the pull-out load required is questioned by the offshore industry. To investigate their efficiency, centrifuge experiments of a reduced scale spudcan model with jets have been performed at the University of Western Australia. The footing was extracted from penetrations of up to 1.5 diameters in normally consolidated clay. Similar to spudcan extraction in the field, these were carried out under load control, applying a constant extraction force. Both influences of pull-out load magnitude and jetting flow rate were investigated. The study demonstrates that jetting is efficient in facilitating spudcan extraction, as it reduces the required uplift load. Practical guidance is provided in applying the results to field conditions.     

新型铰接式重力锚的设计及其性能研究

重力锚锚固是一种常见的锚固形式。为了能够提供足够的水平承载力,传统型式的重力锚普遍比较笨重,在上拔回收时会产生较大的竖向吸附力,不利于重复利用。针对此问题,设计了一种新型铰接式重力锚,并阐述了其铺设与回收方案。其次采用有限元方法对其整体强度进行了校核,结果均符合规范。最后基于模型试验,对铰接式重力锚在黏土中的运动过程进行了研究,进而确定了其在黏土中的水平承载力和回收时的上拔力。结果表明：相较于传统重力锚,新型铰接式重力锚在确保水平承载性能的基础上,能够大幅减小上拔力,从而有效地降低铺设和回收作业的难度,且可适应多种海底土质,但该锚型仅适用于悬链线式系泊系统。相关研究结果可为实际工程中铰接式重力锚的设计提供参考。     

Experimental investigation of the system behaviour of a model three-legged jack-up on clay

Results from combined loading experiments dedicated to evaluating the capacity and stiffness of a single footing have significantly improved the understanding of the response of circular shallow foundations. However, due to experimental practicalities, little corroborative evidence is available to confirm predicted behaviour when multiple footings act within a structural system. This paper addresses this concern by presenting the results of a series of experimental tests on a three-legged model jack-up unit founded on soft, heavily overconsolidated clay. The model adopted geometric features representative of a large prototype rig by appropriately scaling leg height, leg separation and flexural stiffness, as well as the ‘spudcan’ footing diameter and profile. Pushover events were considered by subjecting the model jack-up to monotonic horizontal loading at hull level. By measuring loads and displacements at the hull and at each spudcan, the system behaviour of the jack-up could be analysed. Nine separate tests were performed, revealing how load orientation, leg length and preload ratio changed the system capacity and affected the load–displacement paths of the jack-up and spudcan system. The test results are compared with those derived from single spudcan experiments, and are interpreted within the combined load yield surface approach gaining acceptance within the offshore industry.     

Prediction to the Efficiency of Soft Clay Sample Preparation with Vacuum Loading

Vacuum loading has been examined as a way of preparing uniformly consolidated soft claysamples.The facility and loading procedure are described in this paper.An analytical solution to the threedimensional consolidation equation is derived for estimating the degree of consolidation of the soil samplewith vacuum loading.The given example shows that the predicted degree of consolidation of a soft claybulk with vacuum loading is close to that measured in the consolidation process.     

Bearing capacity and critical punch-through depth of spudcan on sand overlying clay

Spudcan may experience punch-through failure on strong over weak layered soils, such as sand overlying clay. A large deformation finite element method （LDFE） is used to simulate the penetration process of spudcan into sand overlying clay. The sand is simulated by smoothed hyperbolic Mohr-Coulomb model, and the clay is simulated by a simple elasto-plastic model which obeys Tresca yield criterion. According to the LDFE results of a large amount of cases, the effects of the strength, unit weight and thickness of the top sand layer, as well as the effect of the strength of the underlying clay on the spudcan punch-through behavior, are investigated. The critical depth occurring punch-through and the critical bearing capacity are presented in charts. Fitting equations to calculate the critical punch-through depth and the critical bearing capacity are proposed for the convenience of engineering practice.     

A new method of combination of electroosmosis,vacuum and surcharge preloading for soft ground improvement

As a rapid and effective ground improvement method is urgently required for the booming land reclamation in China＇s coastal area, this study proposes a new combined method of electroosmosis, vacuum preloading and surcharge preloading. A new type of electrical prefabricated vertical drain （ePVD） and a new electroosmotic drainage system are suggested to allow the application of the new method. This combined method is then field-tested and compared with the conventional vacuum combined with surcharge preloading method. The monitoring and foundation test results show that the new method induces a settlement 20% larger than that of the conventional vacuum combined with surcharge preloading method in the same treatment period, and saves approximately half of the treatment time compared with the vacuum combined with surcharge preloading method according to the finite element prediction of the settlement. The proposed method also increases the vane shear strength of the soil significantly. The bearing capacity of the ground improved by use of the new proposed method raises 118%. In comparison, there is only a 75% rise when using the vacuum combined with surcharge preloading method during the same reinforcement period. All results indicate that the proposed combined method is effective and suitable for reinforcing the soft clay ground. Besides, the voltage applied between the anode and cathode increases exponentially versus treatment time when the output current of power supplies is kept constant. Most of the voltage potential in electroosmosis is lost at electrodes, leaving smaller than 50% of the voltage to be effectively transmitted into the soil.     

Estimation of Uplift Capacity of Rapidly Loaded Plate Anchors in Soft Clay

Plate anchors are extensively used in civil engineering constructions as they provide an economical alternative to gravity and other embedded anchors. The rate of loading is one of the important factors that affects the magnitude of soil resistance as well as soil suction force. This article outlines the effect of pullout rate on uplift behavior of plate anchors (70 mm diameter) buried in soft saturated clay by varying the pullout rate from 1.4 mm/min to 21.0 mm/min. The variation of breakout force and suction force with embedment depth and rate of pull are presented. A correlation between the rate of increase of undrained strength of clay and anchor capacity with rate of strain has been established. Finally an empirical equation has been proposed that includes the rate of pull in the estimation of breakout capacity of anchors.     

Estimation of Uplift Capacity of Rapidly Loaded Plate Anchors in Soft Clay

Plate anchors are extensively used in civil engineering constructions as they provide an economical alternative to gravity and other embedded anchors. The rate of loading is one of the important factors that affects the magnitude of soil resistance as well as soil suction force. This article outlines the effect of pullout rate on uplift behavior of plate anchors (70 mm diameter) buried in soft saturated clay by varying the pullout rate from 1.4 mm/min to 21.0 mm/min. The variation of breakout force and suction force with embedment depth and rate of pull are presented. A correlation between the rate of increase of undrained strength of clay and anchor capacity with rate of strain has been established. Finally an empirical equation has been proposed that includes the rate of pull in the estimation of breakout capacity of anchors.