任意干湿路径下非饱和土的水力耦合本构模型

大量试验表明饱和土样经历脱湿过程进入吸湿阶段后,在高饱和度区域,残余气体会以封闭气泡的形式分布在土样孔隙中,此时土样呈现较大的压缩性,当吸湿过程结束基质吸力再为0 kPa时,土样并不会达到完全饱和状态。韦昌富等(2008)提出的非饱和土的本构模型没有考虑残余含气量的影响,认为土样在吸湿过程后仍能达到完全饱和状态,这与实际情况有一定偏差。为了更精确地模拟真实情况,基于考虑不同残余含气量的毛细滞回内变量理论和忽视残余含气量影响的非饱和土的水力耦合本构模型,提出了考虑不同残余含气量影响的非饱和土的修正本构模型。通过和实测数据的比较,修正模型可以较好地模拟任意干湿路径下的非饱和土力学特性。     

一个高饱和度非饱和土的本构模型

高饱和度的非饱和土中由于气体处于封闭状态,其内部气压的变化必将对土体的行为产生影响。首先,对高饱和度非饱和土特性进行探讨和研究,随后,在已有非饱和土模型框架基础上,采用广义有效应力原理,建立一个适用于高饱和度条件下的非饱和土的弹塑性本构模型。模型中引入气相耗散的影响,在硬化方程中考虑封闭气体压力改变的影响。最后,利用已有的试验结果来对模型进行验证,并将模型预测结果与前人模型进行对比,表明模型预测可以很好地预测土体的行为,尤其是在高饱和度条件下其结果比其他模型更加接近实际情况。     

非饱和土水-力本构模型及其隐式积分算法

在已有工作基础上建立了水力-力学耦合的非饱和土本构模型,在硬化方程中考虑饱和度的影响,同时在土水特征曲线中考虑了塑性体变的影响,从而使模型可以反映非饱和土中的毛细现象与土中弹塑性变形现象的耦合行为。采用隐式积分方法,建立了非饱和土耦合模型的数值模型,并推导了得到了水力-力学耦合的非饱和土的一致切线模量。利用该算法编制了本构模型计算的子程序,使其能向外输出切线刚度矩阵,用于有限元计算。为了验证该算法和程序的正确性,用所编制程序对不同路径下的土体行为进行了预测。通过预测结果与试验结果相对比,表明程序预测结果与试验数据相吻合,模型可以较好地模拟土体的水力-力学耦合行为特性。     

非饱和土毛细滞回与变形耦合弹塑性本构模型

在修正剑桥模型的基础上,提出了一个非饱和土毛细滞回与骨架变形耦合的弹塑性本构模型。该模型考虑了基质吸力与饱和度对屈服应力的影响,可以同时描述非饱和土的弹塑性变形特性与毛细循环滞回效应。根据塑性体变的产生使非饱和土进气值增大的特点,建立了变形对土-水特征曲线影响的数学描述。该模型有效地考虑了饱和度对前期屈服应力的作用,准确地反映了土体在不同土-水状态条件下（脱湿和吸湿过程）强度特性的变化,而且还可以有效地描述水力循环历史对土体变形的影响。通过与试验数据对比,证明了该模型能够模拟非饱和土的主要力学特性。     

非饱和土的水力和力学特性及其弹塑性描述

简单回顾了非饱和土本构模型研究的发展历程,总结了近几年非饱和土弹塑性本构模型最新研究成果,重点介绍了能统一模拟非饱和土水力性状和力学性状耦合的弹塑性本构模型。通过对建立模型过程中的几个核心问题讨论,较详细地说明该类模型的结构、性能以及相关问题。非饱和土水力性状的滞回性用假定存在饱和度弹性区间的弹塑性过程来模拟;该类耦合模型不仅考虑了吸力对非饱和土水力性状和力学性状的影响,还考虑了饱和度对应力-应变关系和强度的影响以及土体变形对土-水特征曲线的影响。用同一套模型参数,耦合模型可统一预测在吸力控制或含水率控制下沿各种应力路径下非饱和土的水力-力学特性,并简单介绍了膨胀性非饱和土的弹塑性本构模型以及耦合模型在有限元数值计算中的应用。     

考虑毛细滞回效应的非饱和多孔介质渗流与变形耦合本构模型

在Wheeler本构模型框架的基础上,提出了一个水力与力学耦合的本构模型。该模型中的土-水特征曲线采用毛细滞回内变量模型,能够更好地描述水力历史变化下毛细滞回现象对非饱和多孔介质变形的影响,同时也可描述非饱和多孔介质变形对渗流的影响。非饱和土的强度不仅与吸力有关,而且受到饱和度的影响。相同的吸力下,土样经过吸湿和脱湿路径的饱和度不同,因此,非饱和土的强度也不同。此模型以体积含水率的塑性变化和体变的塑性变化为硬化参数,不仅能描述基质吸力对非饱和土的强化作用,而且考虑了饱和度对强度及变形的影响。试验结果与模型预测基本吻合,证明该模型能够模拟非饱和土的主要特性。为了简化,此模型是在各向同性荷载下推得的,有待于推广到一般的应力状态     

川西崩坡积混合土循环荷载下非饱和动本构模型

在川西地区,由砂砾石与黏土颗粒构成的混合土路基经常会发生沉降变形问题。对于交通荷载作用下土体中的累积变形,可通过建立循环荷载作用下的动本构模型进行描述。在边界面弹塑性理论的框架内,综合考虑崩坡积混合土非饱和状态和细颗粒含量两大主要影响因素,结合能比较真实描述非饱和土体湿陷性能的LC(loading-collapse)屈服曲线,同时基于可移动映射中心的映射准则,采用经典的修正剑桥模型作为塑性势方程,构建了混合土的非饱和动本构模型,其参数可通过拟合或常规试验获得。通过与试验结果进行对比,该模型不仅可以较好地反映非饱和混合土在静载和循环荷载下的力学特性,而且能够真实地预测土体在加、卸载过程中的滞回特性。其结果可为川西混合土路基沉降变形预测提供理论依据。     

考虑基质吸力变化时非饱和土的一维本构模型

当地下水位上升或地面遇水浸润时,土的饱和度将因毛细作用而变化,以此使土体产生变形。其中由于含水量增加而使土的重度增大,从而引起压缩变形;同时含水量的增加而使基质吸力下降,从而引起土的回弹变形,因此最终变形取决于上述两种变形趋势的综合效应。根据广义Hook定律、Fredlund的双应力状态变量及Brooks和Corey关于基质吸力与饱和度之间的经验关系,建立了K0状态下非饱和土的一维本构模型。将这一模型与分层总和法相结合,可以计算基质吸力变化时土的竖向变形。通过研究发现,非饱和土的地面变形不仅取决于土的性质与土层的厚度,而且依赖于土中吸力变化前后的分布及应力状态等因素。所建议的一维本构模型可以用于非饱和土地基上基础的沉降估算。     

热-水-力耦合作用下非饱和土变形特性的弹塑性模拟

在已有的非饱和土水-力耦合模型基础上,耦合考虑温度影响,建立了一个热-水-力耦合作用下非饱和土弹塑性本构模型。该模型以土骨架平均应力、修正吸力和温度为应力状态变量,以土骨架应变、饱和度和熵为应变状态变量。通过引入与温度相关的屈服面(LY、TY)以及相应的硬化规律来考虑温度对土体变形的影响。利用建立的模型,对文献中不同吸力和温度条件下的等向压缩和三轴排水剪切试验进行预测,预测结果表明,该模型能够较好地定量描述热-水-力耦合作用下非饱和土的变形特性。     

非饱和上海软土水力和力学特性耦合弹塑性模拟

目前大多数非饱和土的弹塑性本构模型用非饱和击实土的试验结果进行验证,但现场其他类型的土,如沉积土经常有在非饱和状态下外部环境变化的情况。现有的非饱和土弹塑性模型是否适用于沉积土一类的现场土是需要研究的课题。进行非饱和上海第③层土的吸力控制排水排气三轴剪切试验,使用文中提出的能统一考虑非饱和土水力性状和力学性状的弹塑性本构模型,预测上述三轴试验结果,并与试验数据进行比较。比较结果显示,建立的本构模型能够很好地预测非饱和上海软土的水力和力学性质,说明该模型不仅可以适用击实土的预测,还能够很好地适用于其他类型非饱和土的水力和力学性质的模拟。     

A bounding surface model for unsaturated soils considering the microscopic pore structure and interparticle bonding effect due to water menisci

The interparticle bonding effect due to water menisci plays an important role in the hydromechanical coupling properties of unsaturated soils. This paper presents an unsaturated hydromechanical coupling model that considers the influence of matric suction, degree of saturation, and microscopic pore structure on the interparticle bonding effect. The enhanced effective stress and bonding variable are selected as constitutive variables. The bonding variable is correlated with the ratio between unsaturated void ratio and saturated void ratio. The deformation characteristics of unsaturated soils are described based on the bounding surface plasticity theory. A soil–water characteristic model that considers deformation and hydraulic hysteresis is integrated into the constitutive model to achieve hydromechanical coupling. The proposed model can effectively describe the hydromechanical coupling characteristics and the meniscus bonding force of unsaturated bimodal structure soils; the model parameters can be easily obtained through routine experiments. The experimental results of unsaturated isotropic compression, the wetting/drying cycle, and unsaturated triaxial shear tests are used to validate the capability of the proposed model.

     

Implementation of a hydromechanical elastoplastic constitutive model for fully coupled dynamic analysis of unsaturated soils and its validation using centrifuge test results

Prediction of unsaturated soil behavior during earthquake loading has received increasing attention in geotechnical engineering research and practice in recent years. Development of a fully coupled analysis procedure incorporating a coupled hydromechanical elastoplastic constitutive model for dynamic analysis of unsaturated soils has, however, been limited. This paper presents the implementation of a coupled hydromechanical elastoplastic constitutive model into a fully coupled dynamic analysis procedure and its validation using a centrifuge test. First, the fully coupled finite element equations governing the dynamic behavior of unsaturated soils with the solid skeleton displacement, pore water pressure, and pore air pressure as nodal unknowns are briefly presented. The closest point projection method is then utilized to implement the coupled hydromechanical elastoplastic constitutive model into the finite element equations. The constitutive model includes hysteresis in soil–water characteristic curves, cyclic elastoplasticity of the solid skeleton, and the coupling mechanisms between the SWCCs and the solid skeleton. Finally, the analysis procedure is validated using the results from a dynamic centrifuge test on an embankment constructed of compacted unsaturated silt subjected to base shaking. Reasonable comparisons between the predicted and measured accelerations, settlements, and deformed shapes are obtained.

     

不饱和土动弹塑性本构模型研究

以饱和度与有效应力为状态变量,通过引入描述不饱和与饱和土孔隙比差的状态变量,将Zhang等提出的饱和土体应力诱导各向异性动弹塑性本构模型推广到不饱和土体中,使其可描述不饱和土在动力循环荷载作用下的力学特性行为。通过对已有不饱和土体在完全不排水条件下的动三轴试验进行理论模拟,验证了所提出不饱和土本构模型的正确性。最后基于所提出本构模型,讨论了在不排水条件下初始饱和度对不饱和土动力特性研究。结果表明,不饱和土在动力荷载作用下,土体的孔隙比将减少,导致饱和度增加;当初始饱和度较高时,不饱和土会转化为饱和土,从而发生液化现象。该研究成果对研究不饱和土在地震等动力荷载作用下的力学特性行为具有重要意义。     

Review of fundamental principles in modelling unsaturated soil behaviour

An unsaturated soil is a state of the soil. All soils can be partially saturated with water. Therefore, constitutive models for soils should ideally represent the soil behaviour over entire ranges of possible pore pressure and stress values and allow arbitrary stress and hydraulic paths within these ranges. The last two decades or so have seen significant advances in modelling unsaturated soil behaviour. This paper presents a review of constitutive models for unsaturated soils. In particular, it focuses on the fundamental principles that govern the volume change, shear strength, yield stress, water retention and hydro-mechanical coupling. Alternative forms of these principles are critically examined in terms of their predictive capacity for experimental data, the consistency between these principles and the continuity between saturated and unsaturated states.     

Simulation of liquefaction of unsaturated soil using critical state soil model

Several researchers have reported that the mean effective stress of unsaturated soils having a relatively high degree of saturation gradually decreases under fully undrained cyclic loading conditions, and such soils can be finally liquefied like saturated soils. This paper describes a series of simulations of fully undrained cyclic loading on unsaturated soils, conducted using an elastoplastic model for unsaturated soils. This model is a critical state soil model formulated using effective stress tensor for unsaturated soils, which incorporates the following concepts: (a) the volumetric movement of the state boundary surface containing the critical state line owing to the variation in the degree of saturation; (b) the soil water characteristic curve considering the effects of specific volume and hydraulic hysteresis; and (c) the subloading surface concept for considering the effect of density. Void air is assumed to be an ideal gas obeying Boyle's law. The proposed model is validated through comparisons with past results. The simulation results show that the proposed model properly describes the fully undrained cyclic behavior of unsaturated soils, such as liquefaction, compression, and an increase in the degree of saturation. Finally, the effects of the degree of saturation, void ratio, and confining pressure on the cyclic strength of unsaturated soils are described by the simulation results. The liquefaction resistance of unsaturated soils increases as the degree of saturation and the void ratio decrease, and as the confining pressure increases. Furthermore, the degree of saturation has a greater effect on the liquefaction resistance than the confining pressure and void ratio. Copyright © 2017 John Wiley & Sons, Ltd.     

Variation with time of the factor of safety of slopes excavated in unsaturated soils

While the evolution with time of the factor of safety against slope failure is well understood for excavations performed under fully saturated conditions, this evolution has not been extensively studied for excavations carried out in unsaturated soils. The objective of this paper is to investigate the relationship between the factor of safety and time for an excavation performed in an unsaturated silty soil, employing the finite element method. A hypothetical boundary value problem is considered and two types of analyses performed; in the first one, unsaturated soil behaviour is modelled through appropriate constitutive and soil–water retention curve models, whereas in the second one full saturation is assumed. The effect that the saturated soil permeability, its variation with suction, the increase of apparent cohesion due to suction, the depth of the groundwater table and the hydraulic hysteresis have on the results of the unsaturated analysis is examined in a parametric study. The analyses results demonstrate that for unsaturated soils the factor of safety may increase with time, in contrast to what is commonly accepted to be the case in fully saturated soils. Furthermore, it is not possible to know in advance which one of the two types of analysis performed (i.e. the saturated or the unsaturated) will produce conservative results. It is, therefore, advisable to perform unsaturated analysis in geotechnical practice, when dealing with excavations in such soils.     

非饱和土弹塑性模型参数的试验确定及有限元法

简要介绍广泛应用的非饱和土Alonso模型的原理与发展,并通过3组共7个试样的非饱和土三轴试验,得到模型的11个参数。在饱和土Cam本构关系的基础上,推导出一个基于非饱和土Alonso模型的应力-应变增量方程的计算公式,该方程与饱和土的本构方程形式相同。编制了能够考虑净应力和吸力二者对土体硬化规律影响的有限元程序,从而为非饱和土弹塑性计算提供一条途径,便于进一步应用于实际工程。     

非饱和结构性黄土本构模型的研究

本文在饱和土扰动概念基础上,提出了可以考虑外力和增湿两个扰动因素对非饱和土结构性影响的耦合扰动变量。根据复合材料均匀化理论的思想建立了适用于非饱和结构性黄土的本构模型,并给出了耦合扰动变量的演化方程。通过将BBM模型和本文模型的计算结果分别与已有的实验结果进行对比说明,本文模型能够更好地反映非饱和原状黄土的力学特性。通过对结构性参数、进行分析说明,所给出的耦合扰动变量的演化方程能够较好地描述土结构性随变形劣化的规律。