利用对称四极横向剖面法探测走滑断层的应用

从走滑断层难以探测的实际出发,讨论了其物性特征;通过对低阻板模型的物理模拟、数值模拟以及对实地观测资料的分析,研究了对称四极纵、横向剖面法视电阻率曲线的变化特征和差异. 结果表明,横向剖面法相对纵向剖面法异常幅度明显增加,可对地震活动断层进行更为有效的探测和定位. 这一研究为走滑断层探测提供了新的思路. 同时,利用对称四极横向剖面法可以解决走滑断层难以探测这一技术难题.      

电阻率横向剖面探测走滑断层的数值模拟研究

本文从走滑断层难以探测的实际出发,讨论了其物性特征。通过对实际模型的数值模拟,讨论了纵、横向剖面电阻率的变化特征。数值模拟结果证明横向剖面和纵向剖面相比在断层探测中有明显的优越性,为走滑断层探测提出了新的思路。     

电阻率横向剖面法及其在隐伏断层探测中的应用研究

针对两盘无明显断距的城市活动断层难以探测的实际问题，根据断层带电阻率特点，提出了电阻率横向剖面法，在物理模拟和数值模拟基础上，通过现场实际断层或裂隙带的探测结果证明：电阻率横向剖面对两盘无差异断层的探测和定位较常规剖面准确，解决了两盘无明显断距断层的探测问题.     

AN ELECTRICAL RESISTIVITY PROFILE IN HAWAII WITH NOVEL ELEVATION CORRECTION*

In order to locate relatively optimum sites for drilling exploratory holes for fresh water, an electrical resistivity survey was conducted along the new Mahukona-Kawaihae Road on the west flank of the Kohala Mountain. Two resistivity soundings made at the same stations, using the Schlumberger electrode configuration, determined an a spacing of 275 feet for horizontal profiling with the Wenner array. The correlation coefficient of the elevation to profile data was 0.41. A procedure for removing elevation effect from observed apparent resistivity was developed. Based on the reduced resistivity profile, four relatively optimum sites for additional exploration, such as by drilling, are specified. There is no specific interpretation of the data that can definitely indicate the occurrence of large underground reservoirs of fresh water anywhere along the profile. This is because the interpretation of horizontal profiling data is essentially relative and not absolute.     

郯庐断裂带中段(沂沭断裂带)电性结构研究与孕震环境

穿过郯庐断裂带中段（沂沭断裂带,36°N）所做的大地电磁测深（MT）剖面长约150km.使用Robust技术和远参考道大地电磁方法处理观测数据.通过分析视电阻率、阻抗相位、Swift二维偏离度和区域走向,定性确定测区的电性结构.二维反演解释中选择非线性共轭梯度（NLCG）方法,使用TE、TM两种模式资料联合反演,沿剖面的二维电性结构显示：自西向东,鲁西隆起、郯庐断裂带、胶莱坳陷及鲁东隆起4个电性区块分别对应,鲁东和鲁西隆起区为高阻,郯庐断裂带电性结构复杂,高、低阻相间,胶莱坳陷为低阻（高导）区.沿MT剖面附近曾发生3个地震,其震源区处在电性变化剧烈部位,并在震源区附近存在高导体.     

Shallow fault location in coal measures using offset Wenner resistivity profiling1

The five-electrode resistivity configuration of Barker, who introduced the concept of offset resistivity measurements, is used in a profiling mode in the search for lateral variations of resistivity down to depths of a few tens of metres. Theoretical computations show that plotting simple pseudosections of offset measurements over faults is sufficient to reveal the fault position. The method is subsequently applied in the field for locating a buried fault in coal measures. Although offset pseudosections are often all that is required, apparent resistivity pseudosections are examined and compared to collations of 1D inversions of the sounding profile data and to computations over 2D models. It is shown that apparent restivity pseudosections may present a rather misleading picture.     

Tracing an Intra-montane Fault: An Interdisciplinary Approach

This paper presents the results of combined geophysical and morphostructural research of a significant tectonic lineament forming the boundary between the core Bohemian Forest (?umava) Mts. and its foothills of Po?umaví. The exact course, length and character of the fault have not yet been studied in detail despite its possible role in the uplift of the mountain range. To assess the fault course, length and continuity, we have employed a combination of geophysical, morphological and morphostructural methods. These indirect methods had to be applied as the fault only rarely outcrops along its course, and the morphological border is not straightforward. In the beginning, GIS morphometric methods have been applied to assess the influence of the fault on the present relief. Thereafter, structural measurements of joint systems were undertaken together with the analyses of linear structures within the relief. Finally, resistivity profiling at multiple sites across its estimated course has helped to localise the exact position of the fault. Altogether, fifteen profiles were measured using pole-dipole and dipole–dipole electrode configurations. To obtain more detailed results, the resistivity profiling was supplemented by electrical resistivity tomography on three profiles. The paper brings two main results. Firstly, the combination of morphostructural and geophysical methods brings information that each separately cannot, particularly when the faults have no outcrops. Secondly, it was found that the studied fault stretches along the whole study area. Moreover, indicators point to its possible continuation towards the south-east.     

Three-dimensional tomography using high-power induced polarization with the similar central gradient array

Induced polarization (IP) 3D tomography with the similar central gradient array combines IP sounding and IP profiling to retrieve 3D resistivity and polarization data rapidly. The method is characterized by high spatial resolution and large probing depth. We discuss data acquisition and 3D IP imaging procedures using the central gradient array with variable electrode distances. A 3D geoelectric model was constructed and then numerically modeled. The data modeling results suggest that this method can capture the features of real geoelectric models. The method was applied to a polymetallic mine in Gansu Province. The results suggest that IP 3D tomography captures the distribution of resistivity and polarization of subsurface media, delineating the extension of abrupt interfaces, and identifies mineralization.     

湖相沉积盆地内隐伏断裂的电阻率层析成像探测——以通海盆地为例

本文利用电阻率层析成像方法对湖相沉积盆地——通海盆地内的小江断裂的西支断裂进行了探测。发现在电阻率图像的较深区域才能识别出断裂的位置和产状,它在通海盆地内的走向约为N47°E,倾角约为57°～66°,视倾向为NW或N,与以往的研究结果基本一致。     

RESISTIVITY TYPE CURVES OVER OUTCROPPING VERTICAL DYKE—II *

The theoretical horizontal resistivity profiles Over an outcropping vertical dyke with two-electrode and Schlumberger electrode systems are discussed. The two-electrode array seems very useful in locating the highly conducting thick or thin vein, while the Schlumberger (gradient) array is suited to detect the conducting vein of low and moderately high resistivity contrast and as well as the resistive vein of all widths and resistivity contrasts. Besides, the inline gradient array has a distinction of establishing a clue to evaluate the resistivity contrast of the vein.     

The effectiveness of azimuthal apparent-resistivity measurements as a method for determining fracture strike orientations

Azimuthal apparent-resistivity measurements are made for the purpose of determining the strike direction of subvertical fracture sets. Data are collected about a common centre, with an electrode array expanded along a sufficient number of azimuths to define the variation of apparent resistivity with orientation. The apparent resistivities for any one electrode spacing are then plotted in a polar diagram. If the data form an ellipse, this is often interpreted as reflecting aligned, subvertical fracturing. However, it is also possible for heterogeneity within the rockmass to manifest itself, at the scale of the measurement, as a variation of apparent resistivity with azimuth. It is recommended that the offset Wenner array is used for all measurements and that a parameter is introduced, the homogeneity index, which defines whether the variations due to homogeneous anisotropy, such as subvertical fracturing, are greater than those due to inhomogeneity. This simple parameter, which is the quotient of two standard deviations, is valid for both single-peaked and multiple-peaked ellipses. A four-stage scheme for the interpretation of azimuthal data is suggested and a consistent set of quantitative measures is recommended. These will allow data, collected by different workers over different lithologies, to be compared. There are a number of geological situations which can give rise to anisotropy within the rockmass and great care is needed when interpreting azimuthal data in terms of aligned fracturing. Numerical modelling of the response to a buried channel of a rotated offset Wenner array demonstrates that elliptical data are generated by such a linear feature. Depending on the location of the array with respect to the channel, these data are either indistinguishable from those generated by aligned fracturing, or can be recognized by application of the homogeneity index. In the case where the response can be identified as being due to a channel, diagnostic information can be derived on the location and strike of the channel.     

郯庐断裂带中段电性结构及其地学意义研究

郯庐断裂带是中国大陆东部一个重要的左行走滑断裂系,对于研究中国大陆的形成演化与构造格局有着十分重要的意义.阿拉善左旗—山东日照超宽频带大地电磁测深剖面在山东莒县附近穿越了郯庐断裂带中段,电性主轴分析结果表明断裂带附近构造走向大致为北东20°;反演电阻率模型表明剖面穿越处郯庐断裂带的宽度约为30 km,断裂带主体是两条切割深度大、陡倾的断裂,西侧断裂切割深度约为60 km,向西倾斜,断面陡立,倾角约为70°,东侧断裂切割深度大于80 km,但小于100 km,界面东倾,陡立,倾角约为60°~80°;这两条断裂都切穿了地壳,但未切穿岩石圈.郯庐断裂带东缘至剖面终端日照,整个地壳为高阻,与断裂带西侧地壳的电性结构差异明显,这表明郯庐断裂带是华北地块与胶辽朝地块的边界断裂.     

青藏高原东北缘玛沁-兰州-靖边剖面地壳上地幔电性结构研究

在青藏高原东北缘至鄂尔多斯地块沿玛沁—兰州—靖边剖面进行62个测点的大地电磁观测,采用Robust技术对观测数据进行了处理和张量阻抗分解.分析了视电阻率和阻抗相位曲线、二维偏离度、区域走向.采用RRI二维反演技术进行了资料的反演解释,二维剖面的电性结构显示：（1）玛沁断裂带、兰州深断裂带、马家滩—大水坑断裂带将剖面分为4个电性区块：巴颜喀拉地块、秦祁地块、边界带和鄂尔多斯地块.（2）区块1、2和4的地壳电性结构有类似特点：上地壳为高阻层,下地壳上部为低阻带,下地壳下部到上地幔电阻率随深度逐渐升高.区块3电性成层性差、结构复杂,是现今构造活动较强烈的地区.（3）玛沁断裂带、海原断裂带和罗山—云雾山断裂带为较陡立的超壳断裂带;西秦岭北缘断裂带为壳内断裂带.     

重力剖面和激电测深联合勘测在涡河断裂研究中的应用

为查明涡河断裂的位置、性质等参数,选择重力剖面和激电测深联合勘测方法,对指定区域进行物探勘测工作。结果表明:由密度差异引起的重力异常位置和岩石电阻率、极化率异常位置基本吻合,说明以重力剖面和激电测深为手段的联合勘测是查找断裂的有效方法。     

网式大地电磁阻抗张量及其影响因素分析

网式大地电磁（Network-MT,N-MT）法采用长数公里至数十公里的电话线为电极线测量电场,很难形成两条笔直且相互垂直的电极线,因此阻抗张量的计算不如大地电磁法中直接.本文依据阻抗张量的旋转规则提出了一种计算N-MT阻抗张量的简便算法.依据该算法计算了中国东北地区5个N-MT测站的阻抗张量,获得了基于阻抗张量的视电阻率、相位曲线和最佳主轴方位角分布图像,为我国东北N-MT资料的进一步处理和解释提供了基础性数据.此外,本文对比分析了朝阳测站中6条N-MT观测电极线上阻抗张量旋转值与观测值之间的差异,重点讨论了产生这种系统性偏差的各种因素,提出其主要因素可能来自“电场等效各向异性”效应,即测站附近的地壳内部存在与观测电极线尺度相比拟的横向非均匀构造,而测站各电极线沿不同方向跨越不均匀构造,此时各电极线上的电场分量不遵循同一电场矢量的分解准则,导致地表观测三角形内阻抗分量不满足统一的阻抗张量旋转规则.     

Method to obtain standard pseudosections from pseudo pole-dipole arrays

This study deals with electrical resistivity tomography data and it is addressed at obtaining, from linear combinations of data, other datasets not directly measured. The method presented here allows performing the fieldwork systematically, without deciding the type of the more suitable common electrode array (e.g. Wenner, Wenner-Schlumberger, dipole-dipole or multiple-gradient) until or even after the interpretation time. The electrode configuration used by this method is denoted as pseudo pole-dipole array, because it is based on the standard pole-dipole one, but avoiding the disadvantage of locating the remote electrode far away from the profile (to “infinity”). The pseudo pole-dipole datasets can be acquired with common equipment using standard pole-dipole recording sequences. Once the desired datasets have been calculated, they can be inverted using standard interpretation software. The procedure used allows a data quality control to be introduced that is similar to the one based on normal and reciprocal measurements. To assess the method we considered noise-contaminated model responses as well as field data. It has been applied to build dipole-dipole and Wenner-Schlumberger datasets. Results show the suitability of both, the proposed method and the quality control.     

电阻率层析成像在沈阳市地震活断层探测中的应用

本文介绍了在沈阳市活断层探测中应用电阻率层析成像方法取得的结果。,认为应用该方法在目标区可以较准确地探测断层的几何结构和物理特征,为沈阳市活断层探测与地震危险性评价研究提供了准确可靠的物探依据。     

USE OF ELECTRICAL RESISTIVITY METHODS FOR THE STUDY OF COAL SEAMS IN PARTS OF THE RANIGANJ COALFIELD (INDIA)*

The surface resistivity method has been used to study a few exposed coal seams located in the northwestern part of the Raniganj Coalfield (belonging to the Damodar Valley Gondwana basin), India. Different electrode configurations, viz., Wenner, two-electrode and half-Schlumberger, have been used with different electrode spacings in horizontal profiling. The vertical distribution of resistivity has been studied using Schlumberger configuration at different locations along the profile. Laboratory studies of resistivity (at partial to full water saturation conditions) and porosity of different coal, shaly sandstone and sandstone samples of the survey area had already been carried out before the field survey. The results indicated the presence of a good resistivity contrast between the coal seams and the surrounding formations. The field results did not bear this out: the resistivity responses of the coal formations on the profiles and sounding curves are not as clear as one would expect for such high contents. The Wenner profiles show a broad resistivity anomaly over the coal seams. Two-electrode profiles are less noisy than Wenner profiles. Sharp peaks have been observed over the coal seams. The half-Schlumberger configuration seems the best: all the coal seams and their edges can be accurately outlined on the resistivity curves. Borehole data close to the profile have been used for correlating the field results. There is good agreement with vertical electrical soundings.     

VLF GROUND SURVEYS,A POWERFUL TOOL FOR THE STUDY OF SHALLOW TWO-DIMENSIONAL STRUCTURES*

The suitability of VLF ground surveys in the investigation of shallow two-dimensional structures is analyzed. For such structures the polar formalism is derived, necessary in practice since the transmitters are generally not in the structural strike or profile. A simple vertical dike is considered to demonstrate the striking anisotropy which can be expected over such a structure, in particular the high apparent resistivity along the direction of a well-conducting dike and the low resistivity across it. The theory is then confronted with the practical example of an asymmetrical vertical dike resulting from a strike-slip fault. Modelling of the survey results is very successful and yields good confirmation of the polar behaviour. VLF ground surveys thus provide a quick and powerful tool for the study of geological accidents within about 100 m of the surface.