水体石油类信息遥感提取模式研究

石油类是水体有机污染物中的一种,其对水体吸收系数的影响主要体现在有色可溶性有机物(chromophoric dissolved organic matter,CDOM)的光吸收特性上。在水色遥感领域,CDOM光吸收特性主要用其在参考波段的吸收系数和光谱斜率来表征。利用2008年5月、2009年8月和2010年6月在辽宁省盘锦市辽河油田境内获取的CDOM吸收系数、水体表观光学特性以及石油类污染浓度等试验数据,确定表征石油类污染水体CDOM吸收光谱特性的光谱斜率;根据光谱斜率以及表征CDOM浓度的440 nm参考波段吸收系数,建立遥感反演水体石油类污染浓度的模式,并利用31个野外现场实测值对模式精度进行了验证,结果表明,该模式的相对误差为7%;将该模式应用于国产卫星环境一号遥感数据,获取双台子河及辽东湾近岸水体石油类污染空间分布图。     

台湾海峡及周边海域水色光谱特性分析

利用2006—2007年4次908计划ST06区块海洋光学调查的数据和MODIS水色遥感数据,对台湾海峡及周边海域的水色光谱特性进行了研究和分析。结果显示该海域的水色光谱主要有4个类型:类型1光谱峰值出现在580 nm附近,谱峰两侧遥感反射率随波长变化迅速减小,主要分布在紧靠中国大陆的海域;类型2光谱峰值出现在540～560 nm之间,具有谱峰宽的特点,主要分布在台湾海峡靠近大陆的一侧;类型3光谱与大洋水体光谱类似,主要分布在台湾西南的南海区域和吕宋海峡区域;类型4光谱在.450 nm附近出现极小值,在500～600 nm之间出现峰值,主要出现在台湾海峡中部和靠近台湾岛的一侧。其中类型2和4水体分布具有明显的季节特征。类型3、4、2、1对应的叶绿素a浓度和悬浮泥沙浓度呈上升趋势,对应的透明度依次降低,该海域以二类水体为主。     

Landsat-8 OLI卫星数据的大气校正检验及其应用

本文检验了Vanhellemont和Ruddick算法在浑浊的海洋沿岸水体中的适用性。采用基于Vanhellemont和Ruddick算法对2013—2015年黄河口水体的landsat-8 OLI数据进行大气校正,该算法得到的OLI反射率与黄河口高光谱实测反射率较一致, R为0.95,在483 nm(蓝)、561 nm(绿)、655 nm(红)波段处平均相对误差为16.4%、17.3%和25.7%。MODIS和Landsat-8 OLI数据获取的悬浮物浓度之间一致性较好, R为0.85,平均相对误差为20.5%,表明该算法适用于黄河口水体。基于时间序列OLI数据,得到了悬浮物浓度时空分布特征。黄河口悬浮物浓度变化差异主要由风速和输沙量引起的,风速和输沙量对悬浮物浓度的影响存在一定的时间滞后现象。     

基于高光谱的射阳河口悬浮泥沙浓度定量反演研究

通过提取高光谱遥感信息,对射阳河口悬浮泥沙浓度与实测光谱及Hyperion影像光谱反射率进行了相关性分析,结果表明：射阳河口含沙水体对实测光谱反射率的敏感波段为898～904nm,对光谱分辨率为10nm的Hyperion影像敏感波段正好位于896nm处,以此构建的指数模型,其相关指数达到0．89。模型的检验显示,相对根均方差值为38．78％,表明单波段896nm对预测射阳河口的悬沙质量浓度具有良好的精度。由于试验取样时间与Hyperion影像的成像时间相匹配,此时水流场较稳定,河口水体中的泥沙运移与扩散规律与影像解译结果相似,即：近岸悬沙质量浓度高,远海浓度低;河口南侧由于属于淤长性海岸,悬沙质量浓度比北侧高。研究结果为利用高光谱分析技术构建海洋悬沙含量的定量反演模型提供了可靠依据,也为海洋水体其他物质成分的定量反演奠定了基础。     

东海海域典型赤潮水体反射光谱模拟研究

东海原甲藻(Prorocentrum donghaiense Lu)是我国东海海域的典型赤潮藻种,其在水体中通常呈垂直非均匀分布,并存在季节性和日内的垂直迁移现象。本文通过量化垂直迁移过程中东海原甲藻的分布状态,利用Hydrolight软件数值模拟各状态下的水体反射光谱,研究其光谱特征和变化规律。利用叶绿素浓度高斯垂向模型表征东海原甲藻在水体中的垂直分布,结合东海近岸海域二类水体的生物光学模型,模拟得到垂直迁移过程中东海原甲藻赤潮水体的反射光谱。对比分析叶绿素浓度垂向分布参数(背景叶绿素浓度、甲藻主体水层厚度、水体总生物量和叶绿素浓度峰值深度)对水体反射光谱的影响。研究结果表明,在东海原甲藻从次表层向表层垂直向上迁移过程中,水体反射光谱数值在蓝绿波段(400—570nm)减小,在黄红波段(570—720nm)增大,特别是在叶绿素荧光效应波段(680nm)处的变化尤为明显。     

基于高光谱传感器的长江口表层悬浮泥沙质量浓度光谱曲线特征研究#br#

悬浮泥沙质量浓度（SSC）是我国河口水体研究的重要水质参数之一,遥感测定SSC是一种重要的方法。为了研究遥感光谱数据和表层悬浮泥沙质量浓度（SSSC）之间的定量梯度关系,本文采集了长江口南汇嘴附近的表层沉积物,定量设计了SSSC的梯度变化值,利用ASD高光谱仪对不同质量浓度含沙水体进行了光学特性测量。结果表明,随着SSSC的增加,水体的光谱反射率曲线具有相似的形态,但也存在一定的差异。当SSSC<36.59 mg/L时,光谱曲线仅在560～580 nm之间有1个反射峰;当SSSC>52.69 mg/L时,光谱曲线第一反射峰位于570～710 nm,并在近红外波段780～820 nm处出现第二反射峰。光谱曲线第一峰值区间存在明显的“红移”现象,且波长的“红移”变化与SSSC的线性拟合R²达到0.91,说明两者呈较强的线性相关性。在400～900 nm光谱范围内,600～860 nm波段对0～200 mg/L范围内的SSSC变化较敏感且比较稳定,740～900 nm波段对>200 mg/L的SSSC的变化具有更强的响应能力。     

石油类污染水体后向散射特性分析——以辽宁省盘锦市双台子河和绕阳河为例

水体悬浮物对溶解在水中的油及乳化油有吸附作用,这种作用会叠加在颗粒物上,对水体的后向散射系数产生影响,而水体后向散射系数是水色遥感的重要参数之一,对建立遥感反演石油类污染浓度半分析模型起着关键性的作用。根据2008年5月在辽宁省盘锦市辽河油田境内双台子河和绕阳河现场测定的水样,对水体组分进行浓度分析,并分别利用分光光度计及后向散射系数测量仪测定水色三要素的吸收系数和水体后向散射系数。根据获取的数据,对石油类污染水体后向散射特性进行分析,分别建立了(1)石油类污染水体后向散射系数光谱模型;(2)石油类污染水体和非石油类污染水体后向散射系数与无机悬浮物浓度的关系模型。研究结果表明:(1)在建立的后向散射系数光谱模型中,幂函数指数平均值为0.87;(2)从相关系数分析来看,对后向散射系数起主要作用的是无机悬浮物浓度,其次是石油类物质浓度,而有机悬浮物浓度几乎没有影响;(3)对于无石油类污染水体,后向散射系数与无机悬浮物浓度为对数关系模型,而与有石油类污染水体更接近线性关系模型。     

大连港海域石油类物质比吸收系数特征分析

利用2018年8月25-27日和2019年5月15-17日在辽宁省大连港及周边海域测定的不同站点、不同时刻的遥感反射比R_(rs),以及不同深度的水体吸收系数和石油类物质浓度数据,分析了水体石油类物质比吸收系数a_o*(λ)的光谱变化规律和在参考波段440nm处的比吸收系数a_o*(440)的垂向分布特征;将基于遥感反射比R_(rs)估算有色溶解有机物CDOM(Colored Dissolved Organic Matter)吸收系数和水体油浓度C_o的模型应用于LANDSAT8卫星数据,反演出该海域a_o*(440)和油浓度专题图,并分析了两者的空间分布特征。结果表明:(1)a_o*(λ)的光谱分布特征遵循e指数衰减方程的变化规律;由于潮汐作用的影响,不同来向海水的石油类物质浓度不同,导致不同时刻不同站点的a_o*(λ)的光谱斜率有一定的差异;(2)CDOM与油物质的混合比吸收系数a_(go)*(440)随深度的垂向变化没有明显的规律,这也是由于涨落潮变化使得不同来向的海水组分有差异所致;(3)a_o*(440)水平变化具有明显的规律;在石油污染浓度C_o高的海域,a_o*(440)呈现低值,在C_o低的海域,a_o*(440)呈现高值。     

海水叶绿素α浓度遥感测量的实验研究

本文描述了1989年11月在青岛即墨岙山养殖基地所做的海水叶绿素σ浓度遥感测量的基础实验。该实验获得了高浓度叶绿素α含量的海水反射光谱。该反射光谱的特征波段为:波谷在485nm;波峰在450nm 和535nm;“节点”在572nm.根据该实验数据选取了叶绿素α浓度两种双波段估算模式.分析结果表明;两种模式的精度都在50%以上,且双波段反射率的差值法优于双波段反射率比值法.     

高光谱特征波段在海洋典型溢油油种识别中的精度评估

溢油种类精准识别对快速有效地治理污染具有重要的意义,高光谱遥感在海面溢油油种识别中至关重要。为探讨海洋典型溢油油种识别的高光谱特征波段范围,通过设计室外模拟溢油实验,在获取原油、燃料油、柴油、汽油和棕榈油等5种油种的实测高光谱数据基础上,运用因子分析和光谱标准偏差分析法遴选溢油油种的光谱特征波段,并利用支持向量机模型开展基于光谱特征波段的油种识别精度评价。结果表明,基于光谱标准偏差分析和因子分析获得的特征波段的油种识别精度分别是83.33%和90.74%,与基于全波段的识别精度相比,整体精度分别提高了3.7%和11.11%。选取的特征波段(360～540 nm, 560～600 nm, 610～630 nm, 640～660 nm)可作为5种油种相互区分的最佳高光谱波段。     

Microbial Biomass and Organic Nutrients in the Deep-Sea Sediments of the Central Indian Ocean Basin

In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance.     

Assessing the Validity of Seismo-Acoustic Predictor Equations for Obtaining Seabed and Sub-Surface Sediment Physical Properties

The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths.     

A Review of Some Environmental Issues Affecting Marine Mining

This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested.     

Increased Particle Fluxes at the INDEX Site Attributable to Simulated Benthic Disturbance

Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement.     

海上大直径钢管桩打桩过程中桩周土强度弱化研究

海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。     

Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification

An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm.     

Determination of In Situ Sediment Shear Strength from Advanced Piston Corer Pullout Forces

The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments.     

Interannual Sea Level Variations and Annual Tides in the Northwestern Pacific

Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone.     

Flow Cytometric Analysis of Coastal Lagoon Bacterioplankton and Picophytoplankton: Fixation and Storage Effects

The effect of different fixation and storage protocols on the flow cytometric (FCM) simultaneous analysis of bacterioplankton and phytoplankton in coastal seawater samples (Mediterranean coastal lagoons) was investigated. FCM measurements (cell number, fluorescence and scatter characteristics) were obtained through DAPI staining. Three fixatives [glutaraldehyde (GA), formaldehyde (FA) and paraformaldehyde (PFA)] and two storage (3 months duration) methods (5 °C and −196 °C) were tested. Two dominant populations were detected in studied samples: bacteria and eukaryotic picophytoplankton. Adding fixatives (2% final concentration) appears necessary to obtain FCM exhaustive counts of all the bacteria and phytoplanktonic cells. This was related to the permeation effect of fixatives which allowed a better DAPI staining of the cells. Maximum fluorescence, i.e. optimal staining of the cells was obtained with FA or PFA, and significant lower fluorescences with GA. Fixed samples stored at 5 °C induced rapid cell loss. Only storage in liquid nitrogen of samples fixed with FA or PFA, allows mid-term (≥4 months) preservation of bacteria or picophytoplankton cell numbers, and limited evolution of DAPI-induced fluorescence and scatter characteristics.