Reinforcement and Arching Effect of Geogrid-Reinforced and Pile-Supported Embankment on Marine Soft Ground

The effectiveness of constructing a geogrid-reinforced and pile supported embankment on soft ground to reduce differential settlement has been studied by pilot scale field tests and numerical analysis. Three-by-three pile groups with varying pile spacing were driven into a layer of soft ground, and a layer of geogrid was used as reinforcement over each pile group. Further, a 2-D numerical analysis has been conducted using the computer program FLAC 2D. The mechanisms of load transfer can be considered as a combination of embankment soil arching, geogrid tension, and stress transfer due to the difference in stiffness between pile and soft ground. Based on the pilot scale field tests and results of numerical analysis, we find that the geosynthetic reinforcement slightly interferes with soil arching, and helps reduce differential settlement of the soft ground. Also, the most effective load transfer and vertical stress reduction at the midspan between piles occurs when the pile cap spacing index D/b (D: pile cap spacing, b: diameter of pile) is 3.0.     

Reinforcement and Arching Effect of Geogrid-Reinforced and Pile-Supported Embankment on Marine Soft Ground

The effectiveness of constructing a geogrid-reinforced and pile supported embankment on soft ground to reduce differential settlement has been studied by pilot scale field tests and numerical analysis. Three-by-three pile groups with varying pile spacing were driven into a layer of soft ground, and a layer of geogrid was used as reinforcement over each pile group. Further, a 2-D numerical analysis has been conducted using the computer program FLAC 2D. The mechanisms of load transfer can be considered as a combination of embankment soil arching, geogrid tension, and stress transfer due to the difference in stiffness between pile and soft ground. Based on the pilot scale field tests and results of numerical analysis, we find that the geosynthetic reinforcement slightly interferes with soil arching, and helps reduce differential settlement of the soft ground. Also, the most effective load transfer and vertical stress reduction at the midspan between piles occurs when the pile cap spacing index D/b (D: pile cap spacing, b: diameter of pile) is 3.0.     

Behavior of soil plugs in open‐ended model piles driven into sands

Calibration chamber tests were conducted on open‐ended model piles driven into dried siliceous sands with different soil conditions in order to clarify the effect of soil conditions on load transfer mechanism in the soil plug. The model pile used in the test series was devised so that the bearing capacity of an open‐ended pile could be measured as three components: outside shaft resistance, plug resistance, and tip resistance. Under the assumption that the unit shaft resistance due to pile‐soil plug interaction varies linearly near the pile tip, the plug resistance was estimated. The plug capacity, which was defined as the plug resistance at ultimate condition, is mainly dependent on the ambient lateral pressure and relative density. The length of wedged plug that transfers the load decreases with the decrease of relative density, but it is independent of the ambient pressure and penetration depth. Under several assumptions, the value of earth pressure coefficient in the soil plug can be calculated. It gradually reduces with increase in the longitudinal distance from the pile tip. At the bottom of the soil plug, it tends to decrease with increase in the penetration depth and relative density, and to increase with the increase of ambient pressure. This may be attributed to (1) the decrease of friction angle as a result of increase in the effective vertical stress, (2) the difference in the dilation degree of the soil plug during driving with ambient pressures, and (3) the difference in compaction degree of soil plug during driving with relative densities. Based on the test results, an empirical equation was suggested to compute the earth pressure coefficient to be used in the calculation of plug capacity using one‐dimensional analysis, and it produces proper plug capacities for all soil conditions.     

Centrifuge modeling of single pile response due to lateral cyclic loading in kaolin clay

In offshore engineering, pile foundations are commonly constructed in marine deposits to support various structures such as offshore platforms. These piles are subjected to lateral cyclic loading due to wind, wave action, and drag load from ships. In this paper, centrifuge model tests are conducted to investigate the response of the existing single piles due to lateral cyclic loading. The cyclic loading was simulated by a hydraulic actuator. It is found that the residual lateral movement and bending strain are induced in the existing pile after each loading–unloading cycle. This is because plastic deformation is induced in the soil surrounding the existing pile during each loading–unloading cycle. By increasing the applied loads during cyclic loading–unloading process, the lateral movements and bending strains induced in the pile head increase simultaneously. As the cyclic loading varies from 10 to 50 kN, the residual pile head movement increases from 40 to 154?mm, and the residual bending strain of the existing pile varies from 100 to 260 με. The ratio of residual to the maximum pile head movements varies from 0.17 to 0.22, while the ratio of residual to the maximum bending strains is in a range of 0.12–0.55.     

Behavior of Pile Group with Elevated Cap Subjected to Cyclic Lateral Loads

The pile group with elevated cap is widely used as foundation of offshore structures such as turbines, power transmission towers and bridge piers, and understanding its behavior under cyclic lateral loads induced by waves, tide water and winds, is of great importance to designing. A large-scale model test on 3×3 pile group with elevated cap subjected to cyclic lateral loads was performed in saturated silts. The preparation and implementation of the test is presented. Steel pipes with the outer diameter of 114 mm, thickness of 4.5 mm, and length of 6 m were employed as model piles. The pile group was cyclic loaded in a multi-stage sequence with the lateral displacement controlled. In addition, a single pile test was also conducted at the same site for comparison. The displacement of the pile cap, the internal forces of individual piles, and the horizontal stiffness of the pile group are presented and discussed in detail. The results indicate that the lateral cyclic loads have a greater impact on pile group than that on a single pile, and give rise to the significant plastic strain in the soil around piles. The lateral loads carried by each row of piles within the group would be redistributed with loading cycles. The lateral stiffness of the pile group decreases gradually with cycles and broadly presents three different degradation patterns in the test. Significant axial forces were measured out in some piles within the group, owing to the strong restraint provided by the cap, and finally lead to a large settlement of the pile group. These findings can be referred for foundation designing of offshore structures.     

新型码头结构在我国港口工程中的应用

对我国近年出现的几种新型码头结构的研究进行了综述和分析。其中，遮帘式板桩码头结构减小了作用于前板桩上的土压力，使板桩码头在大水深情况下得以应用；双排大管桩码头结构使大管桩较高的轴向承载力和抗弯强度得到充分发挥；架空直立式码头解决了内河大水位差情况下建造码头的难题；椭圆型沉箱的应用避免了采用2个圆沉箱产生前后不均匀沉降的技术难题。最后，对上述新型结构的应用进行了总结。     

Lateral cyclic response of an aluminum model pile in sand

Lateral cyclic load tests were performed on an aluminum model pile in dry sand. Two levels of loading were adopted to represent different service load conditions. The maximum number of loading cycles was 1,000. From the test results, it was found that the even though in the service load condition, the pile response was still affected by cyclic effects and a larger load level would produce more significant influence. In a global point of view, the lateral displacement and maximum moment increased with loading cycles, while the secant stiffness within a cycle decreased with cycles. The cyclic effect was more significant on the lateral displacement than on the moment. In a local point of view, cyclic loading would degrade the equivalent subgrade stiffness for the soil shallower than about seven times diameter. In addition, the secant subgrade stiffness within a cycle increased with loading cycles. Some experimental relationships of lateral pile response and loading cycles were built and compared with those in the literature.     

不同径厚比的海底管道压溃屈曲研究

为了探索不同径厚比海底管道的压溃屈曲特性,本文分别采用挪威船级社（Det Norske Veritas,DNV）规范、有限元模拟和深海压力舱模型试验,研究不同径厚比海底管道承载外部水压的能力,并就DNV规范压溃屈曲计算公式对不同径厚比管道的适用性进行了讨论,优化了小径厚比海底管道压溃屈曲的设计方法。研究表明：小径厚比管道的压溃屈曲临界压力对管道径厚比的变化更敏感;DNV规范计算小径厚比管道的压溃屈曲临界压力偏小,在进行深海管道的压溃屈曲设计时,建议采用模型试验结合有限元模拟的方法,计算管道实际可提供的压溃屈曲承载力。     

Initial post-buckling of submerged slender vertical structures subjected to distributed axial tension

This paper proposes an analytical solution for determining the initial post-buckling behaviour of submerged slender vertical steel structures. These structures may have significant bending stiffness and self-weight so that the axial force varies linearly from one end to the other. Such structures constitute main components of drilling and production platforms used for the offshore exploitation of hydrocarbons. An understanding of their structural behaviour after buckling offers opportunities for cost reduction and design optimisation. The initial post-buckling behaviour is evaluated by retaining non-linear curvature terms and using an expansion in series to reduce the governing equation to a set of linear ordinary fourth order differential equations, which are then solved sequentially by power series functions. The paper also presents results from buckling and non-linear large deflection finite element analyses. The numerical results validate and establish a range of application for the analytical formulation. This solution technique is employed to explore the behaviour of slender structures dominated by geometrical (tension) or flexural stiffness.     

Evaluation of pullout load capacity of suction caissons in sand using a three-dimensional displacement approach

An investigation was conducted to obtain analytical solutions for the pullout behavior of a suction caisson undergoing inclined loads in sand. The inclined load is transformed into an equivalent load system in which the vertical, horizontal, and moment loads are applied on the center of the lid of the suction caisson. The vertical and lateral stiffness coefficients along the skirt of the suction caisson in sands are presented using the new three-dimensional elastic solutions taking into account the nonhomogeneous and nonlinear properties of the sand. The vertical, lateral, and rocking stiffness coefficients on the base of the suction caisson are presented considering the solutions of a hollow rigid cylindrical punch acting on the surface of a soil. The yield, pullout, and failure for sands with the nonhomogeneous and nonlinear characteristics are taken into consideration. The effects of the load inclination, the loading depth, and the aspect ratio on the pullout load capacity of the suction caisson are presented. Behaviour of the suction caisson in sand prior to failure is clarified from the relationship between tensile load, displacement, and rotation and that between depth, vertical pressure, and lateral pressure.     

桩-网路堤位移应力分析及其应用

由于桩-网复合地基的结构形式比较复杂,难以采用解析法求得其应力和位移。利用有限差分法对某桩-网法路堤进行了数值模拟,并取得了较好结果。计算结果显示,桩间土沉降线为悬链线,与现场位移监测结果吻合较好;桩身弯矩和桩土应力反映了桩-网复合地基的一些受力机理。分析认为,桩间土沉降较大的主要原因是由土体本身压缩及桩侧弯引起的。     

Role of piles in mitigating the movement of pipes in soft grounds during embankment loading

Abstract

Pipes buried in soft ground can be damaged due to the vertical and lateral movement of the ground during the construction of the embankment. To investigate such a movement of the soft ground, full-scale tests using embankment piles and stabilizing piles were conducted for 70?days. A pile-supported embankment has been used to reduce the deformation of soft ground by transferring the embankment load through piles to the firm layer below the soft ground, whereas stabilizing piles have been employed to resist the lateral earth pressure that is induced in soft ground by embankment loads. The Coupling Area (CA), which was defined as the quantitative index to determine the resistance effect of both settlement and lateral flow of the soft ground when the embankment was reinforced, is adapted. The analysis results of the CA indicate that the piled embankment was more effective for preventing the damage to buried pipe installed near the embankment, while the stabilizing piles had almost the same effect as the piled embankment when the pipe was buried far away from the embankment.     

Vertical dynamic impedance of large-diameter pile considering its transverse inertia effect and construction disturbance effect

The vertical dynamic impedance of the large-diameter pile is theoretically investigated considering the construction disturbance effect. First, the Rayleigh–Love rode model is introduced to simulate the large-diameter pile with the consideration of its transverse inertia effect. The shear complex stiffness transfer model is proposed to simulate the radial inhomogeneity of the pile surrounding soil caused by the construction disturbance effect. Then, the pile–soil system is divided into finite segments, and the governing equation of the pile–soil system subjected to vertical dynamic loading is established. Following this, the analytical solution of vertical dynamic impedance at the pile head is obtained by means of the shear complex stiffness transfer method and the impedance function transfer method. Based on the present solution, a parametric analysis is conducted to investigate the influence of the transverse inertia effect on the vertical dynamic impedance at the pile head and its relationship with the pile–soil parameters. Finally, comparisons with published solutions are carried out to verify the reliability of the present solution.     

Lateral loading of a pile using strain wedge model and its application under scouring

The scour hole around a pile will reduce the capacity of a laterally loaded pile. The strain wedge model is capable to derive a p–y curve for the analysis of a lateral loaded pile on a nonlinear Winkler foundation. To improve and extend the ability of the strain wedge method, a modified strain wedge (MSW) method is developed, in which a nonlinear lateral deflection of the pile is assumed to describe the varied soil strain distribution in the passive wedge. And then by treating the soil weight involved in the strain wedge as a vertical load at the bottom of the scour hole, an equivalent wedge depth is obtained to consider the effect of scour hole dimensions on the response of laterally loaded piles in sand. The validity of the MSW model is proved by comparisons with a centrifuge test without scour. And its applicability in the problem of a pile with scour is performed by a comparison with a model test and a FE analysis. The analysis shows the pile displacement at the pile head with scour can be obtained by multiplying the corresponding deflection without scour with an amplification factor related to scour depth at large load level.     

Lateral dynamic response of a partially embedded pile subjected to combined loads in saturated soil

In this article, an analytical solution is proposed to investigate the lateral dynamic response of a pile which is partially embedded in saturated soil layer and subjected to combined lateral and vertical loads. The saturated soil is described by Biot’s poroelastic theory and the resistance of soil is derived by potential function method. The governing equation of the pile is solved by coupling soil resistance and continuity conditions between the pile and the soil. The dynamic impedances of the pile are then obtained through transfer matrix method. To verify the validity of the proposed procedure, the present solution is compared with available solution for an idealized case. Finally, a parametric study is performed to investigate the effects of various parameters on the stiffness and damping properties of the pile-soil system. It is found that permeability of the soil and vertical load has significant effects on the dynamic response of the pile.     

A finite difference approximation for dynamic calculation of vertical free hanging slender risers in re-entry application

The dynamic calculations of slender marine risers, such as Finite Element Method (FEM) or Modal Expansion Solution Method (MESM), are mainly for the slender structures with their both ends hinged to the surface and bottom. However, for the re-entry operation, risers held by vessels are in vertical free hanging state, so the displacement and velocity of lower joint would not be zero. For the model of free hanging flexible marine risers, the paper proposed a Finite Difference Approximation (FDA) method for its dynamic calculation. The riser is divided into a reasonable number of rigid discrete segments. And the dynamic model is established based on simple Euler-Bernoulli Beam Theory concerning tension, shear forces and bending moments at each node along the cylindrical structures, which is extendible for different boundary conditions. The governing equations with specific boundary conditions for riser’s free hanging state are simplified by Keller-box method and solved with Newton iteration algorithm for a stable dynamic solution. The calculation starts when the riser is vertical and still in calm water, and its behavior is obtained along time responding to the lateral forward motion at the top. The dynamic behavior in response to the lateral parametric excitation at the top is also proposed and discussed in this paper.     

Lateral Global Buckling of Submarine Pipelines Based on the Model of Nonlinear Pipe–Soil Interaction

With the increasing development and utilization of offshore oil and gas resources, global buckling failures of pipelines subjected to high temperature and high pressure are becoming increasingly important. For unburied or semi-buried submarine pipelines, lateral global buckling represents the main form of global buckling. The pipe–soil interaction determines the deformation and stress distribution of buckling pipelines. In this paper, the nonlinear pipe–soil interaction model is introduced into the analysis of pipeline lateral global buckling, a coupling method of PSI elements and the modified RIKS algorithm is proposed to study the lateral global buckling of a pipeline, and the buckling characteristics of submarine pipeline with a single arch symmetric initial imperfection under different pipe–soil interaction models are studied. Research shows that, compared with the ideal elastic–plastic pipe–soil interaction model, when the DNV-RP-F109 model is adopted to simulate the lateral pipe–soil interactions in the lateral global buckling of a pipeline, the buckling amplitude increases, however, the critical buckling force and the initial buckling temperature difference decreases. In the DNV-RP-F109 pipe–soil interaction model, the maximum soil resistance, the residual soil resistance, and the displacement to reach the maximum soil resistance have significant effects on the analysis results of pipeline global buckling.     

Numerical analysis of cross-section ovalization in the deep-sea pipeline lateral buckling process

Abstract

The deep-water pipeline is the main means of transportation in offshore oil and gas development engineering. The deep-water pipeline may incur lateral global buckling due to the high temperature and pressure that are applied on the pipeline to ensure the contents’ liquidity. With the increasing operating water depth, a higher temperature and pressure are applied to the pipeline, causing large lateral deformation and a large bending moment. Due to the inhomogeneous distribution of the bending moment on the cross-section, different points on the cross-section will deform differently. This kind of deformation causes the cross-section to turn into an oval ring. The cross-section ovalization caused by global buckling was rarely analyzed in former engineering practice since the load is relatively low. With the increase in operation water depth and operation load, the ovality caused by global buckling is noticeable. This article analyzed cross-section ovalization caused by pipeline lateral global buckling with a numerical simulation method. The pipelines with different initial cross-section shapes were simulated, and the influence of several impact factors, including load, pipeline and soil factors on the ovality of the cross-section, were analyzed. The results show that the initial cross-section shape type has little effect on the pipeline ovalization pattern. The initial ovality of the pipeline with an oval ring cross-section shape has little influence on the residual ovality. Among all the factors analyzed in this paper, the pressure difference is the primary factor that should be considered in a pipeline ovalization check.     

V⁃H荷载作用下海洋平台吸力式桩桶桩土承载特性研究

用于海洋平台的吸力式桩桶基础作为一种新型平台基础正逐渐成为人们研究的重点。为研究吸力式桩桶单桩基础的受力特性,对V-H（竖向—水平）联合荷载作用下的吸力式单桩基础桩土的承载特性进行了数值模拟,并将数值模拟的有限元解通过与API规范中对p-y曲线的计算方法进行对比来验证有限元模型的可行性,最后采用分级作用力的加载方式对其破坏包络曲线进行绘制,并推导出相应的函数表达式。研究表明,采用ABAQUS有限元分析软件对吸力式桩桶进行数值模拟是可行的,随着对吸力式桩桶所施加V-H联合荷载的不断增大,吸力式桩桶所能体现的应力和弯矩极限值也在随之增大,其位移变化主要在施加荷载的区域附近,最后在联合荷载作用下所体现的极限承载状态,即包络曲线大致呈四分之一的椭圆形状。