用主动调频质量阻尼器控制高层建筑的风致振动

本文提出了用于高层建筑风振动控制的主动调频质量阻尼器（ＡＴＭＤ）设计的一种简单方法。从ＴＭＤ的工作原理出发,在物理意义上显式定义主动控制力的构成,基于结构的ＳＤＯＦ模型和广义脉动风力的高斯白噪声假定,在频域的以最小化结构顶层位移方差为设计目标,对控制力增益进行参数优化,得出控制力增益的封闭解,文中提出了以维持ＴＭＤ行程恒定为目标进行参数选择的设计方案,一超高层建筑作为算例给出,数值分析表明,所设计     

结构模型的AMD主动控制试验

本文介绍了作者研究设计的ＡＭＤ装置。采用五层钢框架１：４模型ＡＭＤ系统安装在模型的顶层,采用多种地震动加速度记录在哈尔滨建筑大学力学与结构实验中心的地震模拟振动台上进行了结构的ＡＭＤ主动控制试验。试验结果表明：ＡＭＤ主动控制系统对结构地震反应的控制是非常有效的。     

高层建筑地震反应最优多重TLD控制

本文以坑层建筑地震反应进行了最优多重ＴＬＤ（ＭＴＬＤ）ｓ控制研究。文中阐述了ＴＬＤ系统的工作原理笔ＭＴＬＤｓ系统的参数；建立了多层结构－ＴＭＬＤｓ系统耦联体系的运动方程；分析了ＭＴＬＤｓ系统的参数对在谐波作用下多层结构动力反应的影响以及各参数之间的关系。     

考虑土与结构相互作用效应的结构减震控制大型振动台模型试验研究

本文设计并完成了考虑土与结构相互作用的结构减震控制大型振动台模型试验。通过对四种结构形式的对比试验，探讨了土与结构相互作用（ＳＳＩ）效应对结构地震反应的影响以及调谐质量阻尼器（ＴＭＤ）在刚性和柔性地基条件下对主体结构的减震效应。通过比较同一地震动作用下主体结构在刚性和柔性两种地基条件下的地震反应，可知：ＳＳＩ效应具有降低和提高结构减震控制效果的双重作用，其综合效果与输入地震动的频谱特性、加速度峰值大小有关。由于ＳＳＩ效应在结构地震反应中发挥着双重的作用，因而使得基于刚性地基假定下设计的ＴＭＤ减震控制系统在柔性地基条件下的控制效果不太理想，甚至会出现负面效应。本文还探讨了在柔性地基条件下影响结构减震控制效果的一些因素。     

大跨度悬索桥振动控制的双向TMD参数研究

用时域内的逐步积分法对无ＴＭＤ和带有不同参数ＴＭＤ的悬索桥进行了时程分析,结果表明,ＴＭＤ的参数对结构的动力特性的抑振效果均有较大的影响,ＴＭＤ的频率不仅影响振动控制的效果也影响结构的表观阻尼,扭转振动的控制可由侧向ＴＭＤ来实现。     

设置TMD,TLD控制系统的高层建筑风振分析与设计方法

本文结合我国现行风荷载规范，研究设置ＴＭＤ、ＴＬＤ控制系统的高层建筑风振分析与抗风设计的实用方法。首先，ＴＭＤ、ＴＬＤ系统的风振控制效果归并到了受控结构的内荷载折减上；其次，导出了满足舒适度标准的结构动侧移界限的相应的计算公式；第三，比较了ＴＭＤ、ＴＬＤ系统的控制效果以及分别对高层钢和钢筋混凝土结构的控制效果；最后，通过大量的计算和分析，分别确定了ＴＭＤ、ＴＬＤ系统参数的最佳取值区间以及参数之间的     

基于状态反馈的结构鲁棒控制

本文采用基于状态反馈的鲁棒控制方法解决地震作用下结构控制问题，首先将结构的运动方程转化为状态方程，利用鲁棒控制方法设计了系统的状态反馈控制律；通过引入控制力权重系数，合理地平衡了控制效果与控制力的关系；对于地震作用下的三层框架模型。仿真验证了该控制方法的有效性，并讨论了各种参数对控制效果的影响。     

ER／MR智能阻尼器耦联的带裙房高层建筑结构地震反应的半主动控制

本文建立了用ER／MR智能阻尼器耦联的带裙房高层建筑结构地震反应半主动控制的设计计算方法,文中,在导出ER／MR智能阻尼器力学模型的基础上,建立了ER／MR智能阻尼器耦联的带裙房层建筑结构地震反应的基本方程,并根据瞬时最优主动控制的原则,提出了ER／MR智能阻尼器耦联的带裙房高层建筑地震反应半主动控制的基于最优主动控制位移的“开关－耗能”半主动控制策略,应用本文方法对主楼20层,裙房5层的计算结构;受控地震反应的模拟计算结构表明,耦联主楼和裙房的半主动的ER／MR智能阻尼器可有效地抑制带裙房高层建筑结构地震反应的鞭梢效应,并可均匀地减小结构各层的震反应,是一种简单,方便和有效的智能控制装置。     

中国西部强震的地表破裂规模与震级、复发时间间隔关系的研究

研究了我国西部走滑型地震的地表破裂长度Ｌ和位移量Ｄ与震级Ｍ＿ｓ和复发时间间隔Ｔ之间的定量关系。结果表明：震级Ｍ＿ｓ和复发间隔Ｔ不仅与Ｌ值有关，还同时与Ｄ值相关；乘积ＬＤ值可用来估算震级Ｍ＿ｓ，比值Ｄ／Ｌ与复发间隔Ｔ密切相关；对于Ｍ＿ｓ或ＬＤ值给定的地震，Ｄ／Ｌ值大（即Ｌ值小或Ｄ值大）的地震，有较长的复发间隔；当破裂长度Ｌ一定时，有较长复发间隔的地震，Ｍ＿ｓ或ＬＤ值较大；当位移量Ｄ相同时，Ｍ＿ｓ或ＬＤ值较大地震的复发间隔较短     

地震作用下非对称结构平动-扭转耦合振动的半主动控制

本文采用半主动控制方法对非对称结构在地震作用下的平动-扭转耦合振动控制进行了研究。首先建立了非对称结构的平动-扭转耦合振动方程和状态空间方程;然后以磁流变(MR)阻尼器为控制装置,结合线性二次型最优控制、最优控制算法和限幅控制策略,提出了基于MR阻尼器的半主动控制方法;最后对半主动控制方法对非对称结构地震反应的控制效果进行了计算分析。结果表明,半主动控制方法可以对非对称结构的水平位移、扭转位移和加速度反应都产生明显的控制效果,适当下调控制力需求时,不会导致控制效果的等比下降,降低MR阻尼器可调控制力上限后,可以减小阻尼器尺寸,便于其在工程实际中的应用。     

基于BP神经网络模型的多层砖房震害预测方法

针对传统的基于地震烈度的建筑物震害预测方法的不足,本文以地震动峰值加速度作为建筑物震害预测的地震动指标,结合几次大地震中多层砖房的震害实例,提出了一种基于BP神经网络模型的建筑物震害预测方法,模型的输入为反映结构抗震性能的各类物理参数,输出为给定地震动峰值加速度下建筑物破坏状态的概率。研究表明:基于BP网络模型的多层砖房的震害预测结果与震害实例的实际情况比较吻合,本文的思路和方法可推广于其他不同类型的建筑结构的震害预测。     

基于灰关联与人工神经网络综合评价模型的多层砖房震害预测

结合几次大地震中多层砖房的实际震害资料,基于灰关联识别方法,解析了各影响因子对多层砖房抗震性能的影响程度。以反映结构抗震性能的各类物理参数作为输入数据,以给定地震动峰值加速度下建筑物破坏状态的概率作为输出数据,采用8-6-5层结构,建立了基于BP人工神经网络的非线性模型,并对震害样本进行了训练。结果表明:利用灰关联分析,可得出各因子对多层砖房抗震性能影响程度的大小排序,有利于实际的工程抗震设计;基于BP人工神经网络模型的多层砖房的震害预测结果与震害实例的实际情况比较吻合,其思路和方法可推广于其他不同类型的建筑结构的震害预测。     

Protection of seismic structures using semi‐active friction TMD

Although the design and applications of linear tuned mass damper (TMD) systems are well developed, nonlinear TMD systems are still in the developing stage. Energy dissipation via friction mechanisms is an effective means for mitigating the vibration of seismic structures. A friction‐type TMD, i.e. a nonlinear TMD, has the advantages of energy dissipation via a friction mechanism without requiring additional damping devices. However, a passive‐friction TMD (PF‐TMD) has such disadvantages as a fixed and pre‐determined slip load and may lose its tuning and energy dissipation abilities when it is in the stick state. A novel semi‐active‐friction TMD (SAF‐TMD) is used to overcome these disadvantages. The proposed SAF‐TMD has the following features. (1) The frictional force of the SAF‐TMD can be regulated in accordance with system responses. (2) The frictional force can be amplified via a braking mechanism. (3) A large TMD stroke can be utilized to enhance control performance. A non‐sticking friction control law, which can keep the SAF‐TMD activated throughout an earthquake with an arbitrary intensity, was applied. The performance of the PF‐TMD and SAF‐TMD systems in protecting seismic structures was investigated numerically. The results demonstrate that the SAF‐TMD performs better than the PF‐TMD and can prevent a residual stroke that may occur in a PF‐TMD system. Copyright © 2009 John Wiley & Sons, Ltd.     

灰关联与人工神经网络在建筑物震害预测中的应用

基于灰关联识别方法,解析了各震害影响因子对多层砖房抗震性能的影响程度;并利用BP人工神经网络非线性模型对震害实例样本进行了训练。结果表明:利用灰关联分析,可得出各因子对多层砖房抗震性能影响程度的大小排序,有利于实际的工程抗震设计;基于BP人工神经网络模型的多层砖房的震害预测结果与震害实例的实际情况比较吻合,其思路和方法可推广于其他不同类型的建筑结构的震害预测。     

A METHOD OF ESTIMATING THE PARAMETERS OF TUNED MASS DAMPERS FOR SEISMIC APPLICATIONS

The optimum parameters of tuned mass dampers (TMD) that result in considerable reduction in the response of structures to seismic loading are presented. The criterion used to obtain the optimum parameters is to select, for a given mass ratio, the frequency (tuning) and damping ratios that would result in equal and large modal damping in the first two modes of vibration. The parameters are used to compute the response of several single and multi-degree-of-freedom structures with TMDs to different earthquake excitations. The results indicate that the use of the proposed parameters reduces the displacement and acceleration responses significantly. The method can also be used in vibration control of tall buildings using the so-called ‘mega-substructure configuration’, where substructures serve as vibration absorbers for the main structure. It is shown that by selecting the optimum TMD parameters as proposed in this paper, significant reduction in the response of tall buildings can be achieved. © 1997 John Wiley & Sons, Ltd.     

城市典型建筑的地震损失预测方法Ⅰ: 结构易损性分析

地震作用下结构的易损性分析是地震灾害损失预测方法的重要组成部分。本文针对多层砌体房屋结构、排架结构和多层钢筋混凝土结构等3种城市典型建筑,首先给出了该类单体建筑的地震结构易损性分析方法,然后对群体建筑的地震易损性分析方法,以及群体建筑的易损性分类方法进行了探讨,为城市典型建筑的地震灾害损失预测和评估提供参考,并为宁波市抗震防灾规划的地震损失预测提供基础。     

An enhanced base isolation system equipped with optimal tuned mass damper inerter (TMDI)

In seismic base isolation, most of the earthquake‐induced displacement demand is concentrated at the isolation level, thereby the base‐isolation system undergoes large displacements. In an attempt to reduce such displacement demand, this paper proposes an enhanced base‐isolation system incorporating the inerter, a 2‐terminal flywheel device whose generated force is proportional to the relative acceleration between its terminals. The inerter acts as an additional, apparent mass that can be even 200 times higher than its physical mass. When the inerter is installed in series with spring and damper elements, a lower‐mass and more effective alternative to the traditional tuned mass damper (TMD) is obtained, ie, the TMD inerter (TMDI), wherein the device inertance plays the role of the TMD mass. By attaching a TMDI to the isolation floor, it is demonstrated that the displacement demand of base‐isolated structures can be significantly reduced. Due to the stochastic nature of earthquake ground motions, optimal parameters of the TMDI are found based on a probabilistic framework. Different optimization procedures are scrutinized. The effectiveness of the optimal TMDI parameters is assessed via time history analyses of base‐isolated multistory buildings under several earthquake excitations; a sensitivity analysis is also performed. The enhanced base‐isolation system equipped with optimal TMDI attains an excellent level of vibration reduction as compared to the conventional base‐isolation scheme, in terms not only of displacement demand of the base‐isolation system but also of response of the isolated superstructure (eg, base shear and interstory drifts); moreover, the proposed vibration control strategy does not imply excessive stroke of the TMDI.     

多层住宅砖房的地震易损性分析

本文采用概率方法借助于拉丁超立方采样技术和非线性地震反应过程分析对多层住宅砖房的地震易损性进行分析。其分析样本是根据多层住宅砖房目前常用设计参数值的范围选定参数的代表值，并由这些代表值构成的；分析中考虑了地震荷载、结构反应和结构承载力的不确定性。易损性曲线分别对五个不同结构破坏程度的极限状态给出。     

Seismic response control of frame structures using magnetorheological/electrorheological dampers

Semi‐active control of buildings and structures for earthquake hazard mitigation represents a relatively new research area. Two optimal displacement control strategies for semi‐active control of seismic response of frame structures using magnetorheological (MR) dampers or electrorheological (ER) dampers are proposed in this study. The efficacy of these displacement control strategies is compared with the optimal force control strategy. The stiffness of brace system supporting the smart damper is also taken into consideration. An extensive parameter study is carried out to find the optimal parameters of MR or ER fluids, by which the maximum reduction of seismic response may be achieved, and to assess the effects of earthquake intensity and brace stiffness on damper performance. The work on example buildings showed that the installation of the smart dampers with proper parameters and proper control strategy could significantly reduce seismic responses of structures, and the performance of the smart damper is better than that of the common brace or the passive devices. The optimal parameters of the damper and the proper control strategy could be identified through a parameter study. Copyright © 2000 John Wiley & Sons, Ltd.