用臭氧处理海水对鱼虾的急性毒性效应研究

本实验检测了不同浓度臭氧残留对中国对虾(Penaeus chinensis)、牙鲆（Paralichthys oilvaceus）存活率的影响。结果表明，对虾的耐受力要比牙鲆鱼强，中国对虾在臭氧浓度≥1.0mg/L时，可存活至少48h，而芽鲆在此浓度下3h后，即出现鳃部充血肿胀、呼吸频率加快等不适应现象，48h LC50为0.13mg/L。如果能正确控制臭氧的残留量，利用臭氧净化养殖用水是一个不容质疑的水质净化的好方法。     

亚硝态氮（NO2--N）对吉富罗非鱼的毒性及相关因子

通过NO2--N对吉富罗非鱼的急性毒性试验,研究了NO2--N胁迫过程中的应激反应,pH和NaCl浓度对毒性的影响,以及不同生态环境下吉富罗非鱼对亚硝态氮毒性的耐受性差异等,结果表明:在受试鱼急性中毒96h全致死条件下(NO2--N最小浓度192.49mg/L、PH7.37),当水体pH为6.21±0.19、7.09±0.20、8.40±0.22时,全致死时间96h分别变为62、88、102h,当NaCl浓度达到400.00mg/L时,其解毒作用极其显著(P<0.01)。在受试鱼急性中毒48h不死亡条件下(NO2--N最大浓度60.87mg/L,29.7±1.2℃),温度剧降10±0.8℃时,应激反应发生在持续中毒32h后,中毒40h后受试鱼全部应激致死。生活在温室内水泥池、室外水泥池、土池池塘的吉富罗非鱼对NO2--N耐受性存在很大差异。     

茶皂素在血吸虫病防治上的应用研究 I.茶皂素对血吸虫中间宿主钉螺的杀灭效果

用茶皂素对日本血吸虫中间宿主钉螺进行杀灭试验,初步结果表明,不同产地的茶皂素浸杀成螺、幼螺、蜾卵均有较好的杀灭效果。其中,茶皂素Ⅰ 2.5mg/L,茶皂素Ⅱ,Ⅲ 5.0mg/L,浸杀钉螺的效果均为100%。喷杀成蜾所需浓度较高,效果也稍差。茶皂素对淡水鱼类虽有一定的毒性,但比氯硝柳胺毒性低得多:茶皂素Ⅰ在1.6mg/L以下,茶皂素Ⅱ,Ⅲ在4.0mg/L以下,水温在28℃,48h,鲢鱼全部存活。茶皂素资源丰富,价格低廉,对环境无污染，是具有开发前景的植物杀螺剂。文中还对不同产地的茶皂素的毒性差异原因、使用浓度和方法进行了讨论。     

凡纳滨对虾摄食诺氟沙星强化卤虫的药代动力学研究

应用高效液相色谱法研究了凡纳滨对虾(Litopenaeus vannamei)摄食诺氟沙星强化卤虫(Artemia)的药物代谢动力学。结果表明:强化4~8 h,卤虫体内的药物质量浓度达到最高,此后卤虫体内药物摄入和排除达到一个动态平衡;温度影响诺氟沙星在卤虫体内半衰期:体长3mm和6 mm的卤虫,在4,16,28℃时的半衰期分别为51.33,19.29,18.64 h和39.67,13.26,12.6 h。对虾摄食诺氟沙星强化的卤虫后,对虾组织中药物质量浓度经时过程符合一级吸收二室开放模型;投喂剂量对Tmax和Cmax影响较大,当对虾给药质量分数分别为800,400,200mg/kg时,肌肉中给药后出现最高血药的时间或达峰时间分别为0.403,0.540,0.481 h;肝胰脏中给药后出现最高血药的时间或达峰时间分别为0.826,1.839,1.469 h;肌肉中给药后的最高血药质量浓度分别为98.943,46.752,10.887 mg/L;肝胰脏中给药后的最高血药质量浓度分别为738.267,597.352,415.268 mg/L。药物在对虾肌肉的消除半衰期(约26.688 h)明显长于肝胰脏中消除半衰期(约13.988 h)。     

硒对文昌鱼的毒性效应和生长的影响

本文报道了不同浓度Se~(4 )和Se~(6 )对文昌鱼的毒性效应以及对文昌鱼生长的影响。研究结果表明,Se~(4 )的毒性大于Se~(6 ),且对文昌鱼的致毒效应与底质有关;组织学观察发现,文昌鱼中毒器官主要是鳃、肠和肌肉;适宜浓度的Se~(4 )可明显地促进文昌鱼的生长。     

石油开发污染物毒性监测的实验生物筛选Ⅱ.消油剂对水生动物的毒性比较

用静水式试验方法比较了消油剂对斑节对虾Penaeusmonodon,罗氏沼虾Macrobrachiumrosenbergii,裸项栉虎鱼Ctenogobiusgymnachen和红剑鱼Xiphophorushelleri4种水生动物的急性毒性,并观察了消油剂浓度与水体溶解氧的相关性。结果表明：水体溶解氧与消油剂浓度明显呈负相关。消油剂对斑节对虾仔虾、红剑鱼、罗氏沼虾仔虾和裸项栉虎鱼的半数致死浓度分别为14．9,1725．0,2238.0和5861．4mg·L-1。对消油剂的敏感顺序由大至小为斑节对虾仔虾,红剑鱼,罗氏沼虾仔虾,裸项栉虎鱼。班节对虾仔虾和红剑鱼是监测消油剂生物毒性较为适宜的物种。     

不同条件下哈维氏弧菌(Vibrio harvey)对墨吉明对虾(Fenneropenaeus merguiensis)致病性研究

为研究墨吉明对虾弧菌病的防控方法, 本文通过人工注射感染的方式, 研究不同数量哈维 氏弧菌及在不同温度、盐度、pH、不同硝酸氮、亚硝酸氮和氨氮浓度条件下哈维氏弧菌对墨吉明对 虾的致病性的影响。结果表明: 当人工感染哈维氏弧菌数量为3.16×10⁸ CFU 时, 24 h 内对虾累计死 亡率为96.67%; 哈维氏弧菌数量为3.16×10⁶ CFU 以上, 实验结束时, 对虾累计死亡率都超过了 50.00%.在20-32℃ 范围内, 随着温度升高哈维氏弧菌致病力增强, 并且低温组(20℃ 实验组与 26℃ 实验组)对虾累计死亡率显著低于高温组(32℃ 实验组)(P<0.05).在温度为(24±1)℃ 时, 盐度为 20 时对虾累计死亡率处于较低水平; 在温度为(24±1)℃, 盐度为(22±1)时, 96 h, pH 为8.0 时对虾 累计死亡率最低, 并且与另外两个实验组差异显著(P<0.05); 温度为(24±1)℃, 盐度为(22±1), 硝 酸氮对感染哈维氏弧菌的墨吉明对虾有胁迫作用; 在亚硝酸氮浓度(1.0-10.0 mg/L)、氨氮浓度 (0.5-1.5 mg/L)范围内, 哈维氏弧菌对墨吉明对虾的致病性, 随着浓度升高而增强。本实验为墨吉明 对虾弧菌病的防控提供了理论基础。     

转炉钢渣对两种对虾幼虾的急性毒性效应

初步研究了一定粒径的转炉钢渣对日本对虾（Penaeus japonicus）幼虾和中国明对虾（fenneropenaeus chinensis）幼虾的急性毒性效应。实验结果显示，当钢渣质量浓度为1.8g／L时，日本对虾幼虾96h的最高死亡率为33．33％；随着钢渣质量浓度的增加，死亡率增高；当钢渣质量浓度为18g／L时，其96h的最大死亡率达到了75％。相对于日本对虾幼虾，钢渣质量浓度为18g／L时中国明对虾幼虾96h的最高死亡率只有36．67％。运用直线内插法求出钢渣对日本对虾幼虾96h半致死浓度为1．62g／L，钢渣对日本对虾的安全浓度为0．162g／L，而在实验条件下中国明对虾幼虾的半致死浓度要明显高于日本对虾幼虾。     

如何区分有毒鱼类

正专家大致把有毒鱼类分为三类第一类是棘毒鱼类。这类鱼具有毒腺,能分泌毒液,通过鱼棘刺伤人体,把毒液输入人体,引起中毒。棘毒鱼类包括鳗鲇科、科、科、银鲛科、蓝子鱼科、躄鱼科、角鲨科和刺尾鱼科等许多种类,其中最毒的是魟科的毒(俗称石头鱼),其次是同科的鬼(老虎鱼)和蓑(狮子鱼),这类鱼的背鳍棘的基部有毒腺。     

白斑综合症病毒(WSSV)感染对虾的途径及滴度研究

本研究利用荧光定量PCR技术,开展了白斑综合征病毒(WSSV)感染途径及染病最低病毒浓度的研究.用病毒分别感染对虾的口腔、鳃、背部甲壳和腹部软壳24 h后,利用qPCR测定血液中的病毒拷贝数,结果显示病毒主要通过口腔和鳃入侵宿主,并通过血液循环进行全身感染,但病毒不能穿过对虾的体表引起感染.此外,将对虾分别放在含不同病毒粒子浓度(101、102、103、104、105个/dm3)或含核衣壳的海水中培养,发现当海水中病毒粒子浓度低于102个/dm3时,对虾没有感染病毒,当浓度达到103个/dm3以上时能引起对虾感染.结果暗示103个/dm3是引起对虾感染的最低病毒粒子浓度,而核衣壳则不具有感染性.     

Assessing the Validity of Seismo-Acoustic Predictor Equations for Obtaining Seabed and Sub-Surface Sediment Physical Properties

The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths.     

A Review of Some Environmental Issues Affecting Marine Mining

This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested.     

Increased Particle Fluxes at the INDEX Site Attributable to Simulated Benthic Disturbance

Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement.     

海上大直径钢管桩打桩过程中桩周土强度弱化研究

海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。     

Determination of In Situ Sediment Shear Strength from Advanced Piston Corer Pullout Forces

The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments.     

Interannual Sea Level Variations and Annual Tides in the Northwestern Pacific

Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone.     

《Acta Oceanologica Sinica》Vol. 33(2014) contents

<正>~~     

INFORMATION FOR AUTHORS

<正>Acta Oceanologica Sinica(AOS)is a comprehensive academic journal edited by the Editorial Committee of Acta Oceanologica Sinica and is designed to provide a forum for important research papers of the marine scientific community which reflect the information on a worldwide basis.The journal publishes scholarly papers on marine science and technology,including physics,chemistry,biology,