影响咸淡水界面水敏性的几个因素

文章通过砂柱的水击试验,对水流速度、盐浓度、pH值对咸淡水界面水敏性的影响进行了研究。试验结果表明,咸淡水界面上存在临界盐浓度值和临界流速值,当入流溶液浓度达到临界盐浓度和流速达到临界流速时,都会产生颗粒释放现象,导致砂柱的渗透率下降,水敏性发生。在相同的盐浓度和进水流速条件下,进水的pH值越低,颗粒释放的速度越慢,释放总量越少;进水的pH值越高,颗粒释放的速度越快,释放总量越多。     

不同粒度颗粒在非恒定管流中跟随性试验

管道中固液两相流水击对管道和输送系统可能产生严重的破坏,而固液两相在这种非恒定流中的运动特性是计算最大水击压力变化的重要依据。采用粒子图像测速技术（Particle Image Velocimetry,PIV）,通过试验研究水击发生时,水平圆管中不同平均流速、颗粒粒径条件下,流体介质和粗颗粒在管道断面的速度分布以及粗颗粒跟随性的变化规律。研究结果表明:①在水击发生的不同时刻,圆管流中粗颗粒的流速在管道断面分布呈不规则的抛物线型分布,主要表现为靠近管道壁面底部的颗粒流速略小于靠近管道顶部流速,当颗粒粒径大于1.5 mm,平均流速小于2.5 m/s时,粗颗粒表现出明显的沉降特性;②粗颗粒的跟随性与颗粒受力有密切关系,其中颗粒速度与流体速度的变化量是影响颗粒受力的重要参数;③基于试验数据拟合得到了水击条件下粗颗粒跟随性系数k的经验公式,并分析了颗粒粒径、管道直径、两相流平均流速以及水击发生时间等不同参数对粗颗粒跟随性系数的影响,公式计算值与实测值之间的误差在5%以内。     

染色法测量坡面流流速的最佳测流区长度研究

染色法是测定坡面流流速最常用的方法,但对测流区长度的选择没有统一标准.统一测流区长度不仅能减少流速测定误差,还能提高不同试验间的可比性.本文采用室内变坡水槽试验,用染色法测量表面最大流速并计算平均流速时,选择6个常见测流区长度,以流量法计算的平均流速为参照值,选取5个统计参数(RRMSE、RE、NSE、R2、MAE)作为评价指标,将不同测流区长度下染色法与流量法所获得的平均流速进行比较,分析染色法测量坡面流流速的最佳距离.研究结果表明:当测流区长度为2m和3m时,RRMSE都较小;在2m处,RE、MAE达到最小,NSE、R2最接近1,此时染色法测定的流速与流量法计算的流速最为接近.因此,用染色剂法测量坡面流速度的最佳距离应选在2m.     

关于伊利石结晶度Kübler指数的误差计算

本文讨论了测量Kubler指数时产生的误差来源;提出以统计学方法描述“Strip型”衍射峰的半高宽度及其误差大小;以衍射强度、衍射峰形态与测量条件关系式描述“Digital型”衍射峰半高宽的测量误差大小。并特别提出了数字化衍射仪平滑操作产生的误差原理和总体趋势。提出的原理及公式,不仅适合半高宽的误差计算,也适合于其他衍射参数的分析计算,并可用于数字化光谱分析计算中。     

关于伊利石结晶度Kubler指数的误差计算

本文讨论了测量Ｋｕｂｌｅｒ指数时产生的误差来源;提出以统计学方法描述“Ｓｔｒｉｐ型”衍射峰的半高宽度及其误差大小;以衍射强度、衍射峰形态与测量条件关系式描述“Ｄｉｇｉｔａｌ型”衍射峰半高宽的测量误差大小。并特别提出了数字化衍射仪平滑操作产生的误差原理和总体趋势。提出的原理及公式,不仅适合半高宽的误差计算,并可用于数字化光谱分析计算中。     

红土型镍矿样品加工K值试验

样品逐级破碎、逐级缩分后,试样的粒度与保留试样量之间都应遵循切乔特公式Q≥Kd^2。对红土型镍矿的K值试验,统计缩分样品检测结果在95％的置信度下,分析数据不可疑值、测量值之间无系统误差,测量结果（n=16）相对标准偏差小于5％。单次测定结果与平均结果的测量误差均小于允许误差。     

水深测量误差分析与改正

影响水深测量精度的因素较多,水深测量误差主要有仪器误差、声速误差、潮位观测误差、船速误差和船只因素,较全面进行了测量误差原因分析,针对作业过程,提出采取提高测量精度措施,并通过应用实例说明应用注意事项。     

冰盖下水流速度分布的二维数值模拟分析

基于标准的κ-ε模型,利用有限体积法,对冰盖下水流速度分布进行了二维数值模拟和分析.结果表明:当冰盖和河床糙率比值变化时,水流速度剖面发生变化;冰盖下的最大流速值比速度对称分布时要大,且偏于光滑的一边;在相对光滑壁处近壁流速值大于相应对称分布时的流速值,该结果与实验室实测速度剖面情况吻合.数值试验表明,最大流速点位置的偏移量仅在有限的范围内,冰盖区、床面区及冰盖下水流平均速度相差较小,表明了工程应用中假定各区流速相等是可行的.     

薄层水流速度测量系统的研究

根据水流影响电解质扩散和其导电特性的分析,结合电解质脉冲在水流中迁移的数学模型,设计了薄层水流速度测试系统。用Visual Basic语言编写了操作系统,实现了数据采集、参数计算和分析自动化。实验和模拟结果表明,模拟水槽实验中用流量法测量的流速和电解质扩散法测量的水流速度误差很小,说明用此系统测量浅层水流的流速是可行的。     

JSP-1型虹吸校正翻斗雨量计研制与特点

翻斗式雨量计因雨强影响会产生很大的误差,虹吸雨量计不能数字化降雨过程,并需要人工测量虹吸水量进行虹吸订正.本研究成果利用翻斗计量降雨过程,用精确的虹吸计量值智能校正翻斗的误差,综合了翻斗计量和虹吸计量的优点,将分辨率为0.1mm的翻斗雨量计的测量误差从±15%减小到±2%.因此,JSP-1型虹吸校正翻斗雨量计具有很高的精度.     

The Impact of Biased Sampling on the Estimation of the Semivariogram Within Fractured Media Containing Multiple Fracture Sets

Monte Carlo simulation was used to examine the error (statistical bias) introduced in estimating a sample semivariogram through application of oriented sampling patterns to variables which are correlated with fracture orientation. Sample semivariograms of the directional components of the water velocity were used to illustrate that oriented sampling schemes can provide biased data sets which result in error in the estimation of the semivariogram, particularly in the estimation of the sill (or variance). Three sampling patterns were used to analyze directional semivariograms of the components of the fluid velocity: sampling along lines parallel to the mean regional hydraulic gradient, sampling among lines perpendicular to the mean regional hydraulic gradient, and sampling along fracture segments. The first two sampling patterns were shown to introduce substantial error in the sills of the velocity variograms. It is argued that this error is due to the combination of unequal sampling of fractures with different orientations (i.e., sampling bias) and the systematic variation in the magnitude of the velocity components with orientation of the fracture. As a consequence, it is suggested that correction factors developed to correct fracture frequency statistics need to be extended to improve estimation of spatial moments of variables which are correlated with fracture orientation.     

三峡库区泥沙絮凝临界条件现场测量

三峡库区絮凝现象是细颗粒泥沙淤积的重要原因,泥沙絮凝临界条件对三峡库区泥沙淤积规律和模拟具有重要意义。在三峡库区忠县和奉节河段开展泥沙絮凝的现场测量,基于声学多普勒流速仪（Acoustic Doppler Velocimeter,ADV）和泥沙采样测得同步的瞬时流速和含沙量,通过泥沙扩散理论反算现场泥沙沉速及絮团粒径,得到了三峡库区泥沙絮凝度及其与粒径、流速和含沙量的关系。结果表明:库区细颗粒泥沙发生絮凝,且多为中轻度絮凝,重度絮凝较少;库区泥沙絮凝的临界粒径约为0.018 mm,临界流速约为0.7 m/s,临界含沙量约为0.8 kg/m3。研究结果可为三峡库区泥沙的运动规律以及泥沙淤积模拟等提供一定的理论支撑。     

流速仪在垂直偏角情况下测速误差的研究

悬索缆道测流,往往使流速仪形成垂直偏角,对流速有一定影响.分别率定了LS25-1型旋桨流速仪和LS68-1型旋杯流速仪在不同下倾角时与流速的关系流速仪的垂直偏角对流速有明显影响,并随偏角的加大而增加,偏角在10°以内影响不大;同时也率定了LS68-1型旋杯流速仪自动调整垂直下倾角时与流速的关系,下倾角在10°～30°以内对流速无明显变化,超过30°时,流速系统偏小.解决办法是(1)流速小有偏角时用LS68-1型旋杯流速仪,流速大时用LS25-3型旋桨流速仪,二者均有自动调平的功能;(2)合理选择铅鱼的型式和重量,本文提供了数据.     

明渠弯道水流平均运动规律试验研究

利用高频粒子图像测速PIV(Particle Image Velocimetry)系统对明渠弯道水流进行了测量,在两种不同试验方式的配合下,不仅提供了大量高精度的平面二维流场数据,还成功重构了弯道水流的三维平均流速场,为深入研究弯道水流复杂的时均流动结构提供了试验依据。试验结果表明,由于弯道曲率不连续,水流主流区在弯道入口位于凸岸附近,随后在离心力的作用下逐渐转移至凹岸,并一直维持至弯道出口;凹岸顶托及环流运动导致不同横向位置处的纵向流速剖面近床面区域速度梯度及最大流速的位置沿程发生改变;弯道曲率越大,最大水深平均纵向流速转移至靠近凹岸一侧的位置离弯道入口越远;受上游直段二次流的影响,环流运动在弯道入口断面呈三涡结构,随后快速衰减为双涡结构;弯道主环流的强度沿程先增加后减小,涡核位置沿程往复摆动。     

Flow structure of turbidity currents

A two‐dimensional numerical model is used to describe the flow structure of turbidity currents in a vertical plane. To test the accuracy of the model, it is applied to historical flows in Bute Inlet and the Grand Banks flow. The two‐dimensional spatial and temporal distributions of velocity and sediment concentration and non‐dimensionalized vertical profiles of velocity, turbulent kinetic energy and sediment concentration are discussed for several simple computational currents. The flows show a clear interaction between velocity, turbulence and sediment distribution. The results of the numerical tests show that flows with fine‐grained sediment have low vertical and high horizontal gradients of velocity and sediment concentration, show little increase in flow thickness and decelerate slowly. Steadiness and uniformity in these flows are comparable for velocity and concentration. In contrast, flows with coarse‐grained sediment have high vertical and low horizontal velocity gradients and high horizontal concentration gradients. These flows grow considerably in thickness and decelerate rapidly. Steadiness and uniformity in flows with coarse‐grained sediment are different for velocity and concentration. The results show the influence of spatial and temporal flow structure on flow duration and sediment transport.     

含淹没植物河流水流紊动强度最大值及其影响因素

根据含淹没植物河流水流紊动强度与流速和流速分布的关系,建立紊动强度经验公式,并数学推导证明了紊动强度垂向分布最大值的存在。根据实验数据,该紊动强度最大值的大小及出现位置受植物和水流条件的影响:植物的存在增加水流阻力,植物排列密度改变紊动强度最大值的大小;植物叶片的摆动形成水流紊动的主要干扰源,植物/水深相对高度控制紊动强度最大值的出现位置;断面平均流速的变化改变水流的稳定性和植物冠层的高度,对紊动强度最大值的大小和出现位置均有一定影响。     

Heavy metals in stream sediments: Error versus concentration

A regional geochemical mapping program in southern Norway carried out by the Geological Survey of Norway is based on sampling of stream sediments at road/stream intersections. At each site two individual subsamples have been taken. The subsamples were treated independently during the chemical analysis. This procedure enables an estimation of the reproducibility of the element concentration at each sample site. The paper gives results for the average relative total, sampling and laboratory errors at various levels of metal concentration using data for HNO₃ -soluble Mn, Pb and Cu as examples. For Mn and Pb the relative total error reaches a minimum near the median concentration and increases toward both the high and low concentrations. For Cu the relative total and laboratory errors decrease with increasing concentration throughout the whole concentration range, while the sampling error is fairly constant. The results suggest that the models which are commonly used for error determination in geochemical data, are too simple as far as relationships between error and concentration are concerned.     

悬浮颗粒的浓度对其在饱和多孔介质中迁移和沉积特性的影响

多孔介质中悬浮颗粒迁移和沉积特性的研究对地下污染物净化、石油开采、核废料处置、水土保持等有很重要的意义。对4种不同浓度的悬浮颗粒在3种不同的渗流速度下进行室内试验,研究悬浮颗粒的浓度对其迁移和沉积特性的影响。结果表明,在一定的悬浮颗粒浓度下,随着渗流速度的增加,穿透曲线中的悬浮颗粒的相对浓度也增大。同时,渗流速度一定时,悬浮颗粒的浓度存在一个临界值,小于该临界值,穿透曲线中的相对浓度随悬浮颗粒的浓度增大而增大;大于该临界值时,相对浓度随悬浮颗粒的浓度增大而减小。另外,悬浮颗粒的临界浓度是与渗流速度相关的,随着渗流速度增加,悬浮颗粒的临界浓度也逐渐增大     

A dye-tracing test as an aid to studying karst development at an artesian limestone sub-aquifer: Zagros Zone,Iran

A dye-tracing test is employed to study the karst development and flow regime at an artesian limestone sub-aquifer, the Khersan3 Dam site, Zagros Zone, Iran. Tracer breakthrough curves showed an early dominant peak followed by a pronounced tailing effect. The peak concentration was a response to induced pressure during dye injection. The results suggest that the dye was pushed into the small pores and fissures around the injection point during dye injection. Hence, the dye moved out as a result of matrix and fissure diffusive processes and created a long pronounced tailing. The maximum flow velocity in the upper artesian sub-aquifer ranged from 0.97 to 2.9 m/h. However, the mean tracer velocity ranged from 0.19 to 0.51 m/h based on the mean residence tracer time; consequently, the flow regime in the artesian sub-aquifer was determined to be mainly diffusive. The results reveal (1) a low hydraulic gradient from upstream of the dam axis to downstream; consequently, there is no considerable flow; (2) poor karst development and diffuse flow at the tracing test area; (3) a discharge zone at a location downstream of the dam axis which is the main terminal of general flow direction at the dam site.     

冰盖下水流垂线流速分布规律研究

河道中冰盖显著改变了水流流动结构.采用k-ε紊流模型建立了冰盖下水流流动垂向二维数值模型;根据量纲分析理论提出了流速分布规律的影响因素;针对各种因素的不同组合进行了数值计算,并对其流动特性如最大流速点位置、冰区及床面区平均流速等进行了分析研究;对冬季封冻河道的二点测流法精度进行了理论分析.研究结果表明,冰盖下水流的纵向流速在流动核心区并不遵循对数分布规律,同时揭示了冰盖底部与河床的相对粗糙比、河床相对粗糙度及雷诺数对流速分布规律的影响.