炮孔合理堵塞长度的研究

基于爆破理论和应力波理论,分析了炮孔堵塞物的作用机理及其在炮孔中运动过程,推导出了炮孔堵塞长度的计算公式,并对合理炮孔堵塞长度的选取进行了现场试验,试验结果说明了理论分析的正确性,可为爆破实践提供理论依据。     

不耦合装药爆破对硬岩应力场影响的数值分析

爆破地震勘探石油是一种重要的方法,但爆破地震效应与爆破参数、地质条件等密切相关。采用动力有限元软件ANSYS/LS-DYNA,对柱状炸药与药孔壁之间为空气或其他介质以及空隙间距变化时碳酸盐岩岩石中爆炸应力波的传播规律和爆炸地震波能量的衰减特性进行了数值模拟研究,得到了不耦合装药爆炸时岩石应力、振动速度的衰减规律以及与不耦合系数、间隙介质的关系,分析了不耦合效应对爆炸地震波能量的影响。研究表明,不耦合或耦合不好时会使岩体中爆炸应力波的强度大大降低;耦合状态对岩体应力及速度的衰减系数和衰减指数影响较大;在空隙中注水或灌满泥浆会改善它们的耦合关系,增大下传的爆破能量。所得成果可为我国西南地区优选适合碳酸盐地层地震勘探的激发因素提供技术途径和方法。     

隧洞光面爆破中炮孔堵塞长度的数值分析

炮孔堵塞长度是一个直接关系到爆破效果的重要爆破参数。以实际工程为背景,建立不同炮孔堵塞长度的三维有限元模型,运用ANSYS/LS-DANA数值模拟方法,并引入流固耦合方法模拟计算,通过对关键部位的应力进行分析比较,验证了经典爆破理论,获得了最优的堵塞长度,为爆破数值计算提供借鉴,同时为隧洞光面爆破设计提供参考。     

节理岩体爆破的DDA方法模拟

在非连续变形分析（DDA）方法中,通过跟踪炮孔扩张和炮孔周边裂隙的发展贯通求得爆腔的即时体积,进而根据爆生压力状态方程计算爆腔即时压力,并将爆生压力载荷作用到主炮孔内壁和贯通裂隙面上,实现了爆生产物作用下节理岩体爆破的DDA方法模拟。采用DDA方法模拟了节理岩体中的水平柱状炮孔抛掷爆破问题,得到了爆腔的体积扩张和压力衰减时间曲线,模拟很好的再现了岩石爆破过程中的炮孔扩张、岩体破坏、块体抛掷和爆堆形成过程。     

节理几何特征对预裂爆破效果影响的数值模拟

运用有限元软件AUTODYN 2D计算爆炸荷载与离散元软件UDEC模拟节理岩体相结合的方法研究了节理几何特征对预裂爆破的影响。通过计算可知,预裂爆破时炮孔间的节理组对预裂成缝的影响明显,当节理法线与炮孔连线夹角在一定范围内时,预裂缝沿炮孔连线方向的平直程度随节理与炮孔连线夹角的增大而逐渐趋于平直,其中当节理组与炮孔连线夹角为90°时成缝效果最好,裂缝与炮孔连线基本重合,与理论分析较一致;节理间距对预裂爆破有较大影响,相同条件下节理间距越小,越难形成连通裂缝,减小炮孔间距有利于小节理间距情况下的预裂缝贯通     

爆破荷载作用下岩体振动特征的数值模拟

根据福建牛头山水电站地基岩体爆破开挖监测,运用离散元方法模拟了节理岩体距爆源不同距离处质点的振动速度和频率的变化特征,由此确定岩体质点最大振动速度和振动主频随爆源距离的衰减规律,并得到了距爆源一定距离处质点最大振动速度和振动主频与爆破药量的关系。数值模拟与现场实测的结果表明,用离散元软件UDEC计算得到的岩体振动特征和衰减规律与现场监测结果是基本符合的,误差在工程应用的允许范围之内,因此UDEC用于对岩体动态响应的数值模拟是适合的。     

损伤条件下深部岩体巷道光面爆破参数研究

岩体条件复杂多变,为了提高光面爆破的适应性、改善光面爆破效果,对损伤条件下深部岩体巷道光面爆破参数进行研究。通过对深部岩体巷道光爆层原岩应力场、光面爆破机制和振动损伤特征进行分析,基于爆炸应力波和爆生气体综合作用理论,考虑高原岩应力和岩石损伤影响,提出了损伤条件下深部岩体巷道光面爆破参数确定的计算方法。研究表明, （1）高原岩应力相当于提高了岩石的抗拉强度,不利于炮孔初始裂纹的形成及贯通,宜减小周边眼间距;（2）岩石损伤后,其他条件不变,光面爆破的炮孔间距和抵抗线值可适当加大;（3）高原岩应力和损伤条件下,光面爆破的炮孔间距较小时,容易造成爆后围岩损伤,降低围岩的稳定性能,因此,提高爆破效果的同时应及时加强支护,以确保施工安全和围岩稳定;（4）本文提出的光面爆破参数计算公式,经现场爆破验证效果良好,适用于复杂多变的岩体环境。     

岭澳核电站二期工程基岩爆破安全阈值分析

核电站基础爆破开挖过程中必须严格控制岩体爆破损伤深度,确保建基面安全。以广东岭澳核电站二期工程基础爆破开挖为例,通过现场爆破振动监测、岩体声波试验以及数值模拟,综合分析了岩体爆炸振动衰减规律和损伤特征,研究了距爆源一定距离处岩体振动速度与损伤特征的关系,提出了岭澳核电站二期工程岩体爆炸损伤深度的控制方法,确定了相应的安全阈值。分析结果表明,岭澳核电站二期工程基础爆破开挖时,当距爆源30 m处的岩体质点振动速度不超过5 cm/s时,可保证下卧基岩的损伤深度小于2 m,确保建基岩完整性。     

既有隧道扩建爆破振动数值模拟研究

基于原有隧道改扩建拱顶塌腔段扩建开挖,系统研究了多临空面条件下岩体爆破振动规律。采用完全重启动数值方法和拉格朗日算法分析岩体爆破振动规律,模拟爆破振动对隧道塌腔加固区和既有隧道围岩的影响,并获得了特征点的振动速度和衰减规律。数值模拟的最大振速符合爆破振动安全允许标准的要求,从而验证了爆破设计的可行性,并指导了爆破施工。同时,对隧道塌腔段开挖进行爆破振动监测。通过对比分析现场振动监测数据,数值模拟与现场监测结果吻合。结果表明,采用拉格朗日算法和完全重启动数值模拟方法可以描述隧道多孔毫秒延期爆破破岩和质点振动传播规律。该研究结论对隧道多孔毫秒延时控制爆破工程具有参考和指导意义。     

深部岩体地应力瞬态卸载诱发振动效应的影响因素

针对深埋隧洞爆破开挖振动控制,以瀑布沟水电站2#引水隧洞爆破开挖为工程背景,讨论了地应力瞬态卸荷诱发振动特征及影响因素,并结合实测数据采用数值模拟的方法进行了验证分析。研究发现：中、高地应力条件下开挖面初始应力的瞬间释放诱发的振动是爆破开挖诱发振动的重要组成部分;当波阻抗一定时,开挖面初始应力动态卸荷诱发振动由地应力水平、开挖面初始应力、开挖面面积和振动衰减指数共同决定,动态卸荷诱发振动最强段发生在开挖面的初始应力和开挖面面积综合效应最大的位置;深埋隧洞爆破开挖振动的强度是由爆炸荷载和开挖面初始应力动态卸荷效应共同决定的,减小炮孔排距和进尺、采用较小洞径和分部开挖能有效降低地应力瞬态卸荷效应强度,控制深埋隧洞的爆破振动强度。     

The Influence of Burden on Blast Vibration

There is a common belief within the blasting community that increasing the burden will increase the blast vibration. In order to test this belief in a direct sense, it would be desirable to fire single blastholes with various burdens and monitor the vibrations at many locations. A review of past literature indicates that such direct tests are rare and only scant data is available. Nevertheless, a detailed analysis of this and associated past work (on small-scale blocks and choke blasts) shows no convincing evidence of an influence of burden on blast vibration. On the other hand, by considering the role of reflected waves in a simple analytical model, reasoning is given to show that the vibration might well be insensitive to burden. In view of the scant data available, it was decided to conduct trials of a direct nature, in which 13 single blastholes were fired to a free face. The burdens chosen were 2.6 m, 5.2 m and 10.4 m, and the vibration was measured at typically 10 locations over the range 5 m to 50 m from each hole. The results clearly show that the vibration is independent of such burdens. Furthermore, a side-by-side comparison of a choke blast with a free-face blast showed that the vibration from the holes in the choke blast was not higher than the vibration from the holes in the free-face blast. The present work also shows that vibration, although insensitive to burden, is not insensitive to the condition (i.e., the degree of damage) of the surrounding rock mass. In this regard, blastholes in undamaged ground produce a significantly higher vibration than blastholes in damaged ground. This might well be the reason why pre splits and drop-cuts are observed to produce relatively high vibrations, i.e., it is not because such blasts typically involve large burdens, but rather that they are usually initiated in relatively undamaged ground.     

Studies on the Effect of Burden on Blast Damage and the Implementation of New Blasting Practices to Improve Productivity at KCGMs Fimiston Mine

Wall control blasting practices arc necessary to reduce the impact of blasting on mine faces but can also have a significant negative impact on mine productivity and operating costs. The conventional practice in deep open pit mines is to use so-called trim blasts adjacent to pit walls. To provide burden relief these trim blasts have fewer rows than full production blasts and are fired to a cleared free-face: hence they are termed 'unchoked.' This practice leads to scheduling constraints on the pit operations and can cause ore dilution due to excessive muckpile movement. The use of such trim blasts stems from the perception that increased wall damage results from 'choked' blasts. These concerns are based on the unproven assumptions that blast vibration levels and explosive gas penetration increase with increased blast burden and face confinement. This paper describes work undertaken as part of a major investigation into wall control blasting at the KCGM Fimiston Mine, Kalgoorlie, Western Australia. It details a study to assess damage effects due to blast burden. Borehole air pressure measurements and borehole video camera inspections owere done behind a series of single blastholes drilled owith varying burden distances, as owell as behind a dedicated trim blast and a full production blast. It was found that the measured damage effects, including visible rock cracking, dilation, and the limited extent of gas penetration behind the blastholes, did not vary significantly with burden or blast type for the cases tested. This result was in complete agreement with detailed vibration measurements conducted by Blair and Armstrong [1] during the study, which found that vibration was independent of blast burden. As a result of these investigations, changes to the blasting practices at the mine were implemented. Dedicated trim blasts and free-face blasting have been replaced by modified production blasts and the practice of 'choking' blasts has been introduced. This has resulted in a significant improvement in productivity and cost savings without compromising pit wall integrity.     

Theory and Practice of Air-Deck Blasting in Mines and Surface Excavations: A Review

The mechanism by which the explosive energy is transferred to the surrounding rock mass is changed in air-deck blasting. It allows the explosive energy to act repeatedly in pulses on the surrounding rock mass rather than instantly as in the case of concentrated charge blasting. The air-deck acts as a regulator, which first stores energy and then releases it in separate pulses. The release of explosion products in the air gap causes a decrease in the initial bore hole pressure and allows oscillations of shock waves in the air gap. The performance of an air-deck blast is basically derived from the expansion of gaseous products and subsequent multiple interactions between shock waves within an air column, shock waves and stemming base and shock waves and hole bottom. This phenomenon causes repeated loading on the surrounding rock mass by secondary shock fronts for a prolonged period. The length of air column and the rock mass structure are critical to the ultimate results. Several attempts have been made in the past to study the mechanism of air-deck blasting and to investigate its effects on blast performance but a clear understanding of the underlying mechanism and the physical processes to explain its actual effects is yet to emerge. In the absence of any theoretical basis, the air-deck blast designs are invariably carried out by the rules of thumb. The field trials of this technique in different blast environments have demonstrated its effectiveness in routine production blasting, pre-splitting and controlling over break and ground vibrations etc. The air-deck length appropriate to the different rock masses and applications need to be defined more explicitly. It generally ranges between 0.10 and 0.30 times the original charge length. Mid column air-deck is preferred over the top and bottom air-decks. Top air-deck is used especially in situations, which require adequate breakage in the stemming region. The influence of air-deck location within the hole on blast performance also requires further studies. This paper reviews the status of knowledge on the theory and practice of air-deck blasting in mines and surface excavations and brings out the areas for further investigation in this technique of blasting.     

单临空面岩体中爆破诱发损伤的数值分析

岩石的抗压强度远大于其抗拉强度,所以在单临空面岩体爆破中,工程技术人员关注的不仅是炮孔附近的塑性压剪损伤,更多的是临空面附近的拉裂损伤,临空面若是地表,可能会影响到施工的安全,甚至造成一定的经济损失。以往这类损伤问题的数值模拟中大多只偏向于一方面：或忽略压剪损伤,或不考虑拉裂损伤,故所得出的结论难以满足工程需要。基于合理的应力修正方式,把现有的岩石拉-压损伤本构以简明的方式嵌入到大型LS-DYNA软件中,对单临空面岩体中的柱形和球形药包爆破问题进行了数值模拟,计算结果表明该法能较好地预测岩体中爆破诱发的拉裂、压缩损伤的分布规律和演化趋势。     

论岩体爆破地质力学及爆破性分级

本文对岩体爆破地质力学问题进行了论证。岩体的爆破性按岩体结构类型、地应力特征和爆破震动的影响可分为五类:1.极难爆(整体状结构);2.难爆(块状结构);3.中等(裂隙块状结构、碎裂结构);4.易爆(层状碎裂结构、软弱层状结构);5.极易爆(松散结构、松软结构)。     

浅埋大跨隧道施工爆破监测与减震技术

以沪-蓉线庙垭分岔隧道工程为背景,研究了其浅埋大跨段掘进爆破的地表震动效应及大断面开挖减震控制技术,并结合爆破监测数据的回归分析,确立了地震波垂向衰减规律的数学模型。综合分析地表及洞内地震波的震动特性发现,地表质点振动主振频率主要集中在低频段;由于表土的滤波作用,主振频率随距离的增加而减小的趋势并不明显;洞内混凝土衬砌减弱了爆破对围岩的冲击,高频地震波衰减极快;开挖区上部的地表振速通常大于未开挖区的振速,浅埋大跨隧道爆破安全控制应以已开挖区顶部的地表振速为准。     

爆破开挖对岩体含水裂纹扩展的扰动机制

岩体裂纹的水力劈裂是岩体开裂渗漏甚至施工涌水的重要影响因素之一,也是岩土工程界的研究热点。从断裂力学角度分析了爆破开挖对岩体含水裂纹扩展的扰动作用,结果表明,爆破开挖扰动下,岩体含水裂纹的扩展,与爆炸应力波强度及其入射角、地应力的大小与方向、孔隙水压大小、裂纹的倾角及断裂韧度等因素相关;爆炸应力波的作用,相当于增大了岩体裂纹中的孔隙水压力,每1 cm/s的峰值振动速度相当于增大100 kPa的孔隙水压力,爆破振动速度越大,所产生的爆破扰动荷载越大;岩体开挖引起的岩体裂纹近区地应力及其孔隙水压力的变化,对裂纹的失稳与扩展具有较复杂的影响,可改变裂纹的失稳扩展模式。     

考虑累积损伤效应的围岩变形特性研究

隧道爆破开挖诱发的动力扰动作用范围往往远大于其开挖进尺,同一部位围岩受到循环爆破开挖的多次扰动普遍存在累积损伤。对乌东德水电站左岸导流洞爆破开挖过程中的爆破振动和围岩变形监测进行了监测和数值分析,基于累积损伤理论,通过引入损伤判据及损伤变量,考虑计算中产生的不同程度的损伤区域的岩体参数劣化,并将劣化后的参数引入相应损伤单元进行后续开挖爆破数值模拟计算,从而对岩体爆破开挖累积损伤效应进行模拟。通过比较乌东德水电站导流洞的实测数据以及数值模拟计算结果发现,考虑累积损伤的计算结果无论是爆破振动速度还是围岩变形均更接近于实测值。对爆破开挖的分析模拟中应考虑围岩的多次循环爆破累积损伤效应。     

An introduction to Chinese safety regulations for blasting vibration

By reviewing the development history and the state-of-art, this paper introduces Chinese safety regulations for blasting vibration for adjacent structures and equipments, as well as for structures themselves under blasting operation, such as high rock slopes, underground caverns, foundation rock masses, and fresh concrete. The mechanism of failures or damages induced by blasting vibration, the analysis methods of dynamic stability for rock slopes and surrounding rock mass of underground caverns under blasting vibration, and the influence of blasting vibration on early-aged concrete, etc., are analyzed or explained. Standards adopted in China are compared with those adopted in some other countries. Furthermore, the main problems considered in the revision of Chinese national and industrial regulations are discussed, such as the distinction of different damage mechanics induced by propagation of blasting vibration in rock mass and by dynamic response of various structures, the influence of vibration frequency and duration and so on.     

声波测试技术在评价爆破震动对岩体的影响中的应用

在抽水蓄能电站上水库盆的岩体开挖过程中,通常采用工程爆破的技术手段。爆破施工中要尽可能减小爆破震动对上水库盆的影响,控制岩体松动破坏的范围,为下一步防渗工程的实施奠定基础。如何在提高工程施工效率的同时严格控制爆破震动对岩体产生影响,需要通过各种监测手段和技术方法来监测、分析和评价爆破施工对岩体的影响范围,然后来指导爆破施工。本文通过具体工程案例,介绍了施工前或施工后通过声波测试的实际应用,来评价爆破震动对周围岩体的影响,并圈定具体影响范围。