云南西双版纳埃洛石特征研究

采用X射线衍射(XRD)、扫描电子显微镜(SEM)、傅里叶红外吸收光谱(FT-IR)、X荧光光谱分析(XRF)、电子探针,等现代测试手段,对西双版纳-2μm粒级埃洛石的矿物学特征进行了系统的研究。研究结果表明:该矿床中同时存在10?-埃洛石和7?-埃洛石,以10?-埃洛石为主。埃洛石管的平均长度为约1.25μm,平均外径约0.16μm,内径为15~40 nm,管状结构形态较好,具有天然纳米多孔晶体材料性质。加热后10?-埃洛石中结构水较容易脱除,导致10?-埃洛石转变为7?-埃洛石,但7?-埃洛石的结构水较难脱除,在400℃仍有残留。     

湖南辰溪仙人湾埃洛石型高岭土的矿物学特征与成因简析

运用化学成分分析、X射线衍射、红外吸收光谱、差热-热重分析以及扫描电镜等研究手段，着重研究了湖南辰溪仙人湾高岭土矿的矿物学特征，并结合矿床的地质成矿特征讨论了其成因机制。研究表明，该矿床除有极少量碎屑状石英以及附着于埃洛石外表面的凝胶成因石英外，以10A埃洛石为主，部分为7A埃洛石；埃洛石为形态完整的管状晶体，管长一般为1．0-1．5μm，外径一般0．05-0．1μm。认为该矿床为古岩溶洞穴胶体沉积型埃洛石矿床。     

湖南辰溪仙人湾埃洛石的表面吸附性能研究

通过N2吸附-解吸附、表面电位测试及透射电镜等手段研究了湖南辰溪仙人湾埃洛石的表面吸附性能。本区埃洛石属中空管体,吸脱附等温线属于Ⅱ类等温线。由BJH方程计算孔径在2.5~200 nm之间均有分布,集中在3~40 nm之间,由HK方程计算微孔集中分布在0.6~1.9 nm之间。天蓝色埃洛石孔隙丰富,以中微孔为主,纯白色埃洛石孔隙发育程度相对较低,以微、中、大孔为主。埃洛石的表面零电点接近pH=2。在pH=5~10之间,Zeta电位趋向稳定在-40 mV左右。本区埃洛石比表面积为35~87 m2/g,平均孔径为16.20~30.12 nm,具有很强的气体吸附能力和离子交换吸附能力。天蓝色埃洛石表面吸附性能最强,是优先考虑的开发对象。     

管状埃洛石铝羟基表面的硅烷嫁接及其对布洛芬负载、释放的影响

埃洛石[Al2Si2O5(OH)4.nH2O]是一种1∶1型的层状硅酸盐矿物,其结构单元层由铝氧八面体片和硅氧四面体片组成,结构单元层之间为水分子层。天然埃洛石颗粒多呈管状,其外径通常为30~190 nm,内径10~100 nm,管长0.02~30μm。     

湖南辰溪仙人湾埃洛石型高岭土矿床特征及成因分析

在野外地质矿化特征调查的基础上,通过化学成分分析、光学显微镜、红外吸收光谱、X射线衍射、扫描电镜等手段,对新发现的湖南辰溪仙人湾埃洛石型高岭土矿床特征及成因进行研究发现:此高岭土矿体呈似层状与囊状形态,就位于二叠系/石炭系角度不整合面及二叠统/下二叠统假整合面上,分布在岩溶洞穴体系中。矿石中主要矿物为1nm管状埃洛石,部分为0.7 nm管状埃洛石,原生带矿石中埃洛石的含量达95%以上。该高岭土矿床为次生淋滤胶体溶液沉积-重结晶成因高岭土矿床矿床,系温暖湿润、岩溶发育的环境中,受强淋滤作用,由来自上覆地层砂页岩、煤层、泥灰岩及泥质灰岩中的硅铝物质经过相对富集,形成硅铝溶胶,迁移,在岩溶洞穴中沉淀并再次富集成为凝胶体,脱水老化形成埃洛石。     

管状埃洛石的微结构对其负载活性的制约

采集山西临汾、四川广元、湖北丹江口等地管状埃洛石,通过人工手选提纯,利用X射线衍射、同步热分析、透射电镜、原子力显微镜、氮气等温吸附脱附、酸碱滴定、CHN元素分析等表征手段研究管状埃洛石的晶体结构、热稳定性、孔结构性质、表面位密度等微结构性质,并以8-羟基喹啉为客体分子,探讨埃洛石的微结构对其负载活性的制约机理。结果表明,山西埃洛石具有最丰富的孔结构,比表面积为72.48 m2/g,总孔容积为0.38 cm3/g;而湖北埃洛石的孔结构则最差;山西埃洛石、四川埃洛石、湖北埃洛石的零电荷点p H分别为2.99、3.13、4.72,表面位密度分别为10.4 nm-2、10.0 nm-2和11.3 nm-2。山西埃洛石、四川埃洛石、湖北埃洛石对8-羟基喹啉的负载量分别为7.35%,6.20%,6.02%,这与埃洛石的孔结构和零电荷点p H顺序一致。因此,埃洛石的孔结构和表面羟基含量共同决定埃洛石的负载活性。     

江西蒙山地区硅灰石矿床地质特征及成因探讨

蒙山地区位于江西西部,是我国南方较大的硅灰石矿产资源基地,已探明的硅灰石资源储量约占全国的1/5。区内硅灰石矿体赋存于燕山早期侵入形成的蒙山花岗岩体的外接触带300m范围的下二叠统茅口组含燧石结核、燧石条带灰岩中;矿体多呈似层状、透镜状产出,走向长100~400m,厚度2~20m;矿石中主要矿物为硅灰石、石英、方解石,硅灰石含量一般为55%~70%,矿石化学成分主要为SiO2和CaO。区内燧石灰岩提供了硅灰石形成的硅钙质组合、中深成岩浆岩为钙硅化学合成硅灰石提供了反应热液是两个主要的控矿因素,矿床属层控热变质交代型矿床。     

石英质玉石——秦紫玉的矿物学特征及颜色成因

借助于常规宝石学仪器和偏光显微镜、X射线衍射仪、电子探针、红外光谱仪、紫外—可见分光光度计等仪器设备,对洛南秦紫玉的玉石学特征、显微结构、矿物组成、化学成分以及谱学特征进行了详细研究。结果表明:秦紫玉主要有红色、紫色、绿色及浅黄绿色四种颜色,微透明—半透明,玻璃光泽,折射率1.53～1.55,相对密度2.64～2.66。隐晶质结构,主要组成矿物为粒径5～20μm的他形粒状石英,含量大于90%,次要矿物包括赤铁矿、针铁矿、绿泥石、云母、埃洛石等,还有少量的无定形水合氧化铁等铁质化合物。粒径1～10μm的赤铁矿、针铁矿及无定形水合氧化铁等红褐色铁质化合物呈点状、浸染状无规则分布在石英颗粒之间,其w(FeO)约84.39%～87.08%,含有10%左右的水,是引起玉石红色的主要原因;不同色调的绿色是由玉石中均匀分布的大小约10μm的片状绿泥石和细小鳞片状绢云母(约2～10μm)所引起,云母、埃洛石等黏土矿物会导致绿色玉石呈现浅黄色调;紫色则是由质量分数0.15%～0.23%的钛和铁取代石英晶体中的硅形成空穴色心而呈色。     

西藏朱诺斑岩型Cu-Mo矿床成矿斑岩金红石成因及找矿指示意义

西藏冈底斯成矿带南缘西段新发现的朱诺铜矿床是具有大型规模的斑岩铜钼矿床。金红石是斑岩铜矿床中最典型的副矿物之一,对其成分和结构特征的研究能反演成矿流体演化过程并确定斑岩铜矿的主矿体。在详细的野外地质观察的基础上,对钾化带成矿斑岩(黑云花岗闪长岩)中金红石的研究表明:金红石主要与磁铁矿(Ⅰ类)、赤铁矿共生(Ⅲ类),常形成固溶体分离结构并分布在黑云母裂隙及附近;其次呈板状(长10~80μm,宽3~10μm)、颗粒状(粒径10~40μm)、不规则状独立分布在石英硫化物脉中(Ⅱ类)。Ⅰ类金红石是由钛磁铁矿在富S条件下反应形成的;Ⅲ类金红石由钛铁矿在富氧条件下反应形成的;Ⅱ类金红石是由含Ti的热液结晶沉淀而来的。成矿斑岩全岩中TiO_2的含量为0.66%,为金红石的形成提供了丰富的物源。成矿斑岩金红石中的电子探针分析结果显示,其成分除含有约94%的TiO_2外,还含有V_2O_3,Nb_2O_5,FeO,WO_3,CaO,SiO_2,Al_2O_3,ZrO_2,几乎不含或很少含MgO和MgO。金红石中V_2O_3范围为0.20%~2.39%,平均为0.49%,Nb2O5的含量范围为0.20%~4.63%,平均1.25%,WO_3和FeO的平均含量分别为1.92%和1.81%,且有约0.05%的ZrO_2异常。利用金红石找矿方法开展朱诺矿床外围找矿时,首先必须考虑金红石中V_2O_3的含量(0.2%,Ⅱ类金红石0.5%),在此基础上考虑Nb的含量(0.2%,乙类金红石2.6%),同时考虑W,Fe偏高,Zr异常的特点。对Ⅱ类金红石还需要额外考虑其粒径大于10μm。     

龙岩高岭土矿床地质特征及成矿作用

福建龙岩高岭土矿床是蚀变花岗岩风化残余型矿床。花岗岩风化剖面具有明显的垂直分带性，各带有特征的粘土矿物组合、含量和化学组分。矿石矿物主要有高岭石、埃洛石、水白云母、石英及少量长石。高岭石的结晶有序度较低，粒度一般大于２μｍ。埃洛石粒度多小于２μｍ．龙岩高岭土矿石具有贫铁、钛和自然白度高的特征，属优质大型高岭土矿。其成矿作用经历了内生岩浆分异、热液蚀变和表生风化三大地质作用。     

Wavelength-dispersive X-ray fluorescence spectrometric determination of Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in komatiites

Komatiites are mantle-derived ultramafic volcanic rocks. Komatiites have been discovered in several States of India, notably in Karnataka. Studies on the distribution of trace-elements in the komatiites of India are very few. This paper proposes a simple, accurate, precise, rapid, and non-destructive wavelength-dispersive x-ray fluorescence (WDXRF) spectrometric technique for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in komatiites, and discusses the accuracy, precision, limits of detection, x-ray spectral-line interferences, inter-element effects, speed, advantages, and limitations of the technique. The accuracy of the technique is excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Zr, Nb, Ba, Pb, and Th and very good (within 4%) for Y. The precision is also excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th. The limits of detection are: 1 ppm for Sc and V; 2 ppm for Cr, Co, and Ni; 3 ppm for Cu, Zn, Rb, and Sr; 4 ppm for Y and Zr; 6 ppm for Nb; 10 ppm for Ba; 13 ppm for Pb; and 14 ppm for Th. The time taken for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in a batch of 24 samples of komatiites, for a replication of four analyses per sample, by one operator, using a manual WDXRF spectrometer, is only 60 hours.     

硅酸盐类样品中硅、铁、铝、钛、锰、钙、镁、钾、钠和磷的x射线荧光光谱测定

本文拟定了一种以熔融法制备样片,用X射线荧光光谱测定硅酸盐类样品中Si、Fe、Al、Tj、Mn、Ca、Mg、K、Na、P等元素的分析方法。在对不同靶材X光管和分光晶体实验对比的基础上,选择了最佳的测量条件。该法具有快速、准确,测量范围广,检测限低,价格便宜等优点。经过近百个各种类型标样或管理样品的分析对比表明,本法不仅适用于硅酸盐类岩石样品的分析,还适用于铁矿、铝土矿、碳酸盐类岩矿样品以及水泥、耐火材料等样品的分析。     

高压微波消解法测定醋酸纤维过滤器采集的微尘粒子中的砷镉钴铬铜铁锰镍铅钒锌

最新的流行病学研究表明,空气中较高浓度的悬浮细颗粒可能对人类的健康有不利的影响。根据该项研究显示,由于心脏病、慢性呼吸问题和肺功能指标恶化而导致死亡率的升高与细尘粒子有关。这些研究结果已经促使欧盟于1999年4月出台了限制空气中二氧化硫、二氧化氮、氧化氮、铅和颗粒物含量的法案(1999/30/EC),对各项指标包括对可吸入PM10颗粒的浓度提出了新的限制性指标。PM10颗粒是指可以通过预分级器分离采集的气体动力学直径小于10μm的细颗粒。目前研究的兴趣重点逐步偏向PM2.5这些更细微颗粒物,PM2.5这种颗粒物对健康有明显的不利影响。在欧盟指令2008/50/EC中,对PM10和PM2.5都提     

Isotopic systematics of He,Ar, S,Cu, Ni,Re, Os,Pb, U,Sm, Nd,Rb, Sr,Lu, and Hf in the rocks and ores of the Norilsk deposits

This paper reports the first results of a study of 11 isotope systems (³He/⁴He, ⁴⁰Ar/³⁶Ar, ³⁴S/³²S, ⁶⁵Cu/⁶³Cu, ⁶²Ni/⁶⁰Ni, ⁸⁷Sr/⁸⁶Sr, ¹⁴³Nd/¹⁴⁴Nd, ^206–208Pb/²⁰⁴Pb, Hf–Nd, U–Pb, and Re–Os) in the rocks and ores of the Cu–Ni–PGE deposits of the Norilsk ore district. Almost all the results were obtained at the Center of Isotopic Research of the Karpinskii All-Russia Research Institute of Geology. The use of a number of independent genetic isotopic signatures and comprehensive isotopic knowledge provided a methodic basis for the interpretation of approximately 5000 isotopic analyses of various elements. The presence of materials from two sources, crust and mantle, was detected in the composition of the rocks and ores. The contribution of the crustal source is especially significant in the paleofluids (gas–liquid microinclusions) of the ore-forming medium. Crustal solutions were probably a transport medium during ore formation. Air argon is dominant in the ores, which indicates a connection between the paleofluids and the atmosphere. This suggests intense groundwater circulation during the crystallization of ore minerals. The age of the rocks and ores of the Norilsk deposits was determined. The stage of orebody formation is restricted to a narrow age interval of 250 ± 10 Ma. An isotopic criterion was proposed for the ore-bearing potential of mafic intrusions in the Norilsk–Taimyr region. It includes several interrelated isotopic ratios of various elements: He, Ar, S, and others.     

Viscous, cohesive, non-Newtonian, depositing, radial slurry flow

Mining induced subsidence can significantly affect mining costs where major surface facilities and natural environment need to be protected. Overburden grout injection is a technology used to control coal mine subsidence by injecting the mine waste material extracted from the coal back into the inter-burden rock during longwall mining. The flowing slurry is here categorised as a nonlinear viscous cohesive (Bingham plastic) fluid. During longwall mining the grout slurry is pumped into the separated beds of the rock mass through a central vertical borehole, which is drilled deep into the inter-burden rock strata above the coal seam. However, a blockage can occur in the injection system when the slurry velocity falls below a certain critical threshold velocity, indicating a material phase change from cohesive-viscous to cohesive-frictional. In situ field injection tests through boreholes have been simulated at a smaller scale at the CSIRO laboratory in Brisbane by pumping the slurry through a radial disk (gap = 4 mm) from its centre. Laboratory experiments indicate a general, nonlinear, cohesive, viscous, frictional model for shear behaviour of the slurry, in which the material shear parameters are functions of the disk radial distance. Complete dimensional and dimensionless analytical solutions have been developed based on an approach related to Bingham–Herschel–Bulkley fluid mechanics. The derived formulae include relations for minimum pump pressure, local pressure and pressure gradient, wall shear stress, volume rate, velocity and velocity gradient. The theoretical results match the experimental measurements. The experiments covered slurries with maximum particle sizes of 0.5 to 2 mm with about 50% being larger than 100 µm. The viscosities at the various solids concentrations were measured with a standard torsion viscometer. This study differs from the previous research in several distinct aspects, namely, consideration of the variable shear parameters rather than fixed values, inclusion of total nonlinear behaviour, and implementation of a friction function to mimic behaviour of the deposited and consolidating stiff slurry, which can cause a significant pressure rise as a result of the increased shear resistance.     

硅酸盐中铁、锰、钛、钙、钾、磷、硅、铝、镁、钠、锶、铷、钡的X-射线荧光光谱定量测定

本文介绍样品经四硼酸锂熔融制成玻璃小饼。采用Lachance模式和理论a系数来校正元素间的效应,由3080E型X-射线荧光谱仪和DF-350B数据处理系统完成硅酸盐中十三个项目的测定。     

岩石密度和超高压岩石折返速率

在常温常压条件下对中国大陆科学钻CCSD主孔100-3000米岩心样品进行了密度测量,建立了密度连续剖面,并界定了不同超高压岩石的密度值。通过对比高温高压物性实验资料,岩石密度随着退变程度增强而降低,榴辉岩密度变化序列为3.52g/cm3→3.49g/cm3→3.07g/cm3→2.93g/cm3。超高压长英质岩石密度变化序列为3.00g/cm→2.80g/cm3→2.65g/cm3。上述实验资料是讨论不同折返阶段岩石所受浮力的基础,为研究折返速率大小提供了基本参数。本文通过折返板块运动平衡时,上浮力与粘滞力平衡这一关系式,定量研究了大陆俯冲板块的折返速率,认为密度差产生上浮力从而引起折返,温度对板块折返速率的影响最为显著;密度差大小、折返角度、折返板块大小对折返速率也有直接的影响。定量模拟分析表明,在温度高于850℃时,板块的折返速率可以超过100mm/a;当温度降至700℃时,折返速率则低于1.5mm/a。作者认为在折返早期,温度较高,板块快速折返至60-70km榴辉岩相深度;随着传导散热,温度降低,板块以较慢的速率折返至中下地壳。折返速率的估算表明,浮力是板块折返第一阶段(从>100km深部折返至<40km的中下地壳)的主要驱动力。     

Bellechester,Minnesota, USA,lagoon collapses

Bellechester, Minnesota, is a small community of approximately 155 residents located on the county line between Goodhue and Wabasha counties in southeast Minnesota's karst region. Bellechester is served by a 21-year-old wastewater treatment facility (WWTF) consisting of three waste-stabilization ponds. On 28 April 1992 six sinkholes were discovered to have drained cell 2 of the WWTF resulting in the loss of approximately 8.7×10⁶ 1 of partially treated effluent and about 600 m³ of soil into previously undetected subsurface voids of unknown dimensions. In the week following the collapse, approximately 200 water wells located within a 5-km radius of the WWTF were sampled in an after-the-fact, emergency sampling program. Twelve samples with elevated fecal coliform levels, 18 samples with nitrate-nitrogen greater than the 10 mg/1 standard, and no samples with elevated chlorides were found. However, the elevated levels could not be unambiguously attributed to the WWTF collapse. This is the third WWTF to fail by sinkhole collapse in southeast Minnesota since 1974. All three collapsed lagoons have been located in similar geomorphic and stratigraphic settings. However, at least two lagoons have collapsed in the adjacent area in northeast Iowa, and these lagoons are located at different stratigraphic positions. Twenty-two WWTFs constructed in southeast Minnesota's karst region in the last 25 years have been identified as subject to potential sinkhole collapse. An unknown but significant number of manure storage lagoons, flood control structures, etc., have also been constructed in the karst region and are at risk. Public agencies are beginning to develop plans to deal with the risk associated with existing and future waste lagoons in this environment. The critical hydrogeologic parameters that can be used to prioritize the risk of collapse at existing facilities include: (1) the lithology of the first bedrock beneath each lagoon, (2) the thickness of surficial materials between the lagoon and the bedrock surface, (3) the presence and construction of liners (seepage rate), and (4) the proximity to existing sinkholes.     

Mercury,arsenic, antimony,and selenium contents of sediment from the Kuskokwim River,Bethel, Alaska,USA

The Kuskokwim River at Bethel, Alaska, drains a major mercury-antimony metallogenic province in its upper reaches and tributaries. Bethel (population 4000) is situated on the Kuskokwim floodplain and also draws its water supply from wells located in river-deposited sediment. A boring through overbank and floodplain sediment has provided material to establish a baseline datum for sediment-hosted heavy metals. Mercury (total), arsenic, antimony, and selenium contents were determined; aluminum was also determined and used as normalizing factor. The contents of the heavy metals were relatively constant with depth and do not reflect any potential enrichment from upstream contaminant sources.     

滇东南花岗岩与锡、银、铜、铅、锌多金属矿床的成因关系

滇东南锡、银、铅、锌多金属矿床主要分布在个旧、白牛厂、都龙3个矿区,而滇东南较大的3个花岗岩体又分别出露在3个矿区或附近.花岗岩体均形成于燕山晚期,岩石化学、矿物成分相似,富含锡、银、铅、锌、钨、铜等成矿元素.矿床主金属元素组合与岩体之间的距离由远而近出现由锡、钨、(铍、铌、钽)→锡、钨、(铁)、铜、铟→锡、铅、锌、银、铟、(锑)有规律的变化.花岗岩浆是成矿物质来源和成矿热源.岩浆侵入初期使上覆地层隆起产生背斜(凹陷部位成向斜);同时使地层产生一系列裂隙、压性断层或层间断裂;岩浆侵入晚期,这些断层再次活动,表现为张性,岩浆产生的含矿热液沿由其活动所造成的断裂迁移、充填、交代、沉淀而形成矿床.