偏心荷载作用下条形浅基础荷载-变形特性数值分析

在主应力方向的旋转过程中,主应力方向与塑性主应变增量方向之间存在着非共轴现象。基于屈服角点结构非共轴理论,建立了一种非共轴本构模型,通过有限元软件ABAQUS的二次开发子程序UMAT,将该模型运用到有限元数值计算中。首先,对中密砂单剪试验进行数值模拟,研究了非共轴现象及其对应力-应变关系的影响。然后,针对偏心荷载作用下条形浅基础荷载-变形特性进行数值分析,研究了非共轴现象对荷载-位移关系的影响。研究结果表明:非共轴模型计算得到的荷载增长速度滞后于共轴模型计算结果的增长速度;在地基变形的初期,非共轴现象比较明显,主应力方向的减小速度要滞后于塑性主应变增量方向的减小速度;随着地基沉降的增加,非共轴现象逐渐减弱;非共轴模型与共轴模型计算结果之间的差异在应变硬化情况下更加明显。     

浅基础地基荷载-变形特性的分析研究

在土体主应力方向的旋转过程中,主应力方向与塑性主应变增量方向之间存在着非共轴现象,非共轴现象对应力-应变关系具有显著的影响。通过有限元二次开发,将角点结构非共轴理论应用到有限元程序ABAQUS中;对密砂单剪试验进行数值模拟,研究了非共轴现象及其对应力-应变关系的影响;采用离心模型试验方法,对圆形浅基础作用下饱和密砂地基荷载-变形特性进行试验研究;对离心模型试验进行数值模拟,将试验结果与数值计算结果进行对比,对非共轴模型的计算结果的合理性进行验证。研究结果表明:非共轴现象对浅基础地基荷载-变形特性具有显著的影响;当选取合理的非共轴塑性模量时,非共轴模型的计算结果与离心模型试验结果比较接近。     

Spar平台吸力式基础极限承载特性数值分析

以国外某深海Spar平台工程为背景,针对其所采用的细长型吸力式基础的抗拔承载特性进行三维有限元数值分析.分析中充分考虑土体强度、加载位置和加载角度对吸力式基础极限抗拔承载力的影响,本构模型中钢筒基础采用弹塑性模型.分析结果表明,吸力式基础的极限抗拨承载力随着土体强度的增大而增大,倾斜加载时在基础插入土体部分中点左右加载可取得最大的极限承载力,极限抗拔承载力还随着加载角度的增大而增大.吸力式基础存在倾斜加载时桶基础与桶内外土体的共同塑性屈服破坏和垂直加载时桶外土体的局部剪切破坏等两种不同的破坏模式.     

不同初始固结应力条件下主应力方向对海洋密砂不排水单调剪切特性的影响

利用大连理工大学的“土工静力-动力液压-三轴扭转多功能剪切仪”,针对相对密实度为70％的福建标准砂,在不排水条件下控制试验过程中的中主应力系数保持不变,进行了不同初始固结应力条件下不同主应力方向的单调剪切试验.以此着重探讨了主应力方向及初始固结应力对饱和密砂单调剪切特性的影响,研究表明,主应力方向和初始固结应力对于密砂的有效应力路径和应力-应变关系均具有十分显著的影响.通过与饱和松砂不排水单调剪切特性的对比分析,探讨了初始相对密实度对砂土剪切特性的影响,研究表明随着主应力方向角增大,密砂的应变硬化效应逐渐减弱,但未出现松砂对应的应变软化现象.     

黏土地基上海洋平台桩靴峰值阻力上限分析

在自升式平台的预压载过程中，桩靴在层状地基上较易发生“穿刺”现象，很大程度上影响着平台的安全运行。准确地分析桩靴峰值阻力，避免平台桩靴发生“穿刺”是非常重要的。采用极限分析上限定理，合理构建运动许可速度场，从理论上推导了层状地基上桩靴峰值阻力的上限解答。为了进一步验证峰值阻力理论解答的准确性，采用ABAQUS有限元软件构建了“桩靴—弹塑性海床”的三维数值模型，对桩靴贯入海床的过程进行了数值模拟，分析桩靴周围土体的塑性变形演变规律，研究土体的破坏机理。研究结果表明：推导的桩靴峰值阻力上限解答，能够较好地计算层状地基极限承载能力，通过与离心机试验和数值结果对比，计算误差在18%以内；给出的运动许可速度场能够较好地反映桩靴周围土体破坏模式；桩靴阻力达到峰值时，下层软土中的土塞高度约为桩靴直径的0.2倍。     

考虑蠕变特性的斜坡堤软土地基变形数值分析

目前在防波堤设计和施工中,较少考虑软粘土的蠕变特性对软土地基长期变形的影响.为准确预测斜坡堤软土地基的变形水平,研究采用Plaxis二维有限元程序,利用不考虑蠕变的摩尔-库仑模型和能反映土体时间效应的软土蠕变模型,模拟某斜坡堤地基软土层施工期和工后的地基变形过程,对比分析了两种不同模型的计算结果,表明由软土蠕变模型得到...     

水平荷载作用下砂土中非柔性桩的p-y曲线修正

中国近海风机大多采用长径比10～20范围内的非柔性桩基础,而现有规范方法主要针对长径比大于20的柔性桩,对我国风机基础的适用性一直存在争议。本文利用有限元法研究砂土中非柔性桩的水平受荷响应,主要关注容许范围内的桩基倾斜,因此采用硬化土小应变本构模型描述砂土的应力应变关系。建立钢管桩-土三维有限元模型进行变参数分析,探究土体相对密实度、桩基直径对初始地基反力模量的影响;讨论了正切双曲线函数和双曲线函数描述土体弹簧刚度(即p-y曲线)的合理性;最终提出了适用于砂土中非柔性桩的修正p-y曲线表达式,并通过与三种不同砂土相对密实度与桩基组合工况下的有限元结果对比,验证了修正p-y公式的合理性。结果表明：土体相对密实度、桩基直径与初始地基反力模量均呈正相关;双曲线函数更适合描述非柔性桩的p-y曲线;修正后的p-y公式提高了水平荷载作用下非柔性桩响应的预测精度。     

粉土中吸力桶沉贯阻力与土塞失稳机理研究

针对粉土中吸力桶在吸力沉贯中的两个关键性问题——沉贯阻力和内部土体稳定性,在自行研制的试验平台上进行了一系列吸力桶沉贯模型试验。试验结果表明,粉土中吸力沉贯时,Andersen所提供的基于CPT锥尖强度的阻力计算公式能较好预测阻力发展趋势,但计算结果偏小;而修正的承载力公式预测结果在沉贯前期与实测值较吻合,沉贯后期预测偏大。吸力沉贯前期,贯入阻力随深度稳步增长,直到贯入深度达到某个临界值后,阻力增长缓慢甚至保持不变。桶内粉土在吸力作用下的失稳机理与黏土或砂土不同,在渗透力作用下表现为从土层表面开始的自上而下管涌或渗流侵蚀。沉贯后期,端部土体在较高水头差下发生失稳并向桶内流动,造成了桶内土体密度降低,端阻力与内壁摩阻力降低,总贯入阻力主要由外壁摩阻力提供。并结合有限元模拟对上述实验现象的内在机理进行了解释。     

防波堤椭圆形桶式基础结构的贯入受力特性实验研究

某工程拟在深水软土地基上修筑防波堤,为了尽量减少地基处理充分利用天然地基,创新性设计出一种轻型薄壁的预制防波堤结构,其挡浪部分为直立薄壁圆筒,基础部分则为倒扣的薄壁椭圆形桶,并且椭圆形下桶为外壁和内隔板分成9个格室,防波堤结构浮运至指定位置后,拟采用负压工法施工安装就位。这种新型防波堤结构为国内外首次提出,其下沉施工设计尚无规范可循,为此开展了土工离心模型试验,在模型加速过程中模拟了椭圆形下桶基础在淤泥层中的自重下沉,之后利用新研发了一种大行程作动加载装置给椭圆形下桶施加下推力,让其继续向下贯入直至穿越整个淤泥层,以模拟负压工法的贯入下沉。试验测量了下桶贯入下沉过程中的推力与贯入位移,还尝试测量了桶壁和内隔板断面的压应变,由此分析了下桶基础的下沉总阻力、桶壁摩擦力以及截面压应变随贯入位移的变化。结果发现,这些曲线均出现了转折点,根据转折点对应的下沉总阻力确定了椭圆形下桶基础贯入过程所遭遇的临界下沉总阻力值,据此估算了负压工法中所需施加的压力差。     

扩底抗拔桩动态变形全过程承载特性模型试验研究

利用砂土中扩底抗拔桩的模型试验,研究从开始加载到破坏时扩底抗拔桩地基动态变形全过程的承载特性。试验结果表明:半模试验得到的极限荷载和破坏面均略小于全模试验结果,采用半模试验测量地基变形过程与破坏模式有明显优势,用半模试验代替全模试验是可行的;随着桩顶荷载的增加,扩大头上方的土体由压缩变形逐渐发展为局部的压缩—剪切破坏;扩大头对其上部的桩侧摩阻力有增强作用,对其下部的桩侧摩阻力有削弱作用;扩大头在工作荷载、极限荷载和破坏荷载作用时分担的荷载比例为15%~20%。     

Numerical analysis and centrifuge modeling of shallow foundations

The influence of non-coaxial constitutive model on predictions of dense sand behavior is investigated in this paper. The non-coaxial model with strain softening plasticity is applied into finite-element program ABAQUS, which is first used to predict the stress-strain behavior and the non-coaxial characteristic between the orientations of the principal stress and principal plastic strain rate in simple shear tests. The model is also used to predict load settlement responses and bearing capacity factors of shallow foundations. A series of centrifuge tests for shallow foundations on saturated dense sand are performed under drained conditions and the test results are compared with the corresponding numerical results. Various footing dimensions, depths of embedment, and footing shapes are considered in these tests. In view of the load settlement relationships, the stiffness of the load-displacement curves is significantly affected by the non-coaxial model compared with those predicted by the coaxial model, and a lower value of non-coaxial modulus gives a softer response. Considering the soil behavior at failure, the coaxial model predictions of bearing capacity factors are more advanced than those of centrifuge test results and the non-coaxial model results;besides, the non-coaxial model gives better predictions. The non-coaxial model predictions are closer to those of the centrifuge results when a proper non-coaxial plastic modulus is chosen.     

Investigation of the load-bearing capacity of suction caissons used for offshore wind turbines

This paper presents the results of three-dimensional finite element analyses of the suction bucket foundation used for offshore wind turbines. The behavior of the bucket and the response of soil supporting the bucket in dense and medium dense sandy soils subjected to static horizontal load are investigated. Field tests results and a centrifuge model test are used to validate the numerical model. Dimensionless horizontal load-displacement and overturning moment-rotation relationships are derived utilizing the Power law and Buckingham’s theorem. The results show good agreement between the numerical analysis results and the straight lines obtained from the Power law until a specific value of horizontal load and overturning moment. Regarding stress behavior of soil supporting the bucket, due to soil densification and bucket movement, maximum stresses are seen near the bucket tip at the right inside of the bucket. The major part of the applied load is transferred by the bucket skirt. Numerical analysis modeling results show that the bucket rotation and displacement are highly dependent on the bucket geometry and soil properties in addition to loading conditions. Normalized equations and figures for the ultimate horizontal load and overturning-moment capacities are presented and can be used for the preliminary design of the bucket foundations in sandy soils.     

考虑波浪引起的主应力轴旋转效应的砂土本构模型及其验证

Principal stress axes rotation influences the stress-strain behavior of sand under wave loading. A constitutive model for sand, which considers principal stress orientation and is based on generalized ...     

Liftboat Fixty with the Interaction Between the Soil Foundation and the Structure

A liftboat has big independent spuncans. The interaction between the liftboat structure and the foundation can provide significant fixity. Both methods of numerical simulation and experimental test are adopted to study the fixity. An experimental model to the scale of 1：40 ofa liftboat was mounted on a sand box in the laboratory, and also a three-dimensional FEM model was established in the numerical simulation. The variation of the fixity and the maximum stress in the legs are studied. On the basis of the fact that the experimental data are in good agreement with the numerical simulation results, the fixity is further studied by numerical simulation with different soil foundation parameters and different sizes of spuncans.     

Investigating the monotonic behaviour of hybrid tripod suction bucket foundations for offshore wind towers in sand

Existing tripod suction bucket foundations, utilised for offshore wind turbines, are required to resist significant lateral loads and overturning moments generated by wind and currents. This paper presents an innovative type of tripod bucket foundation, ‘hybrid tripod bucket foundation’, for foundations of offshore wind turbines, which has the ability to provide a larger overturning capacity compared with conventional tripod buckets. The proposed foundation consists of a conventional tripod bucket combined with three large circular mats attached to each bucket. A series of experiments were conducted on small-scale models of the proposed foundation subjected to overturning moment under 1g conditions in loose sand. Different circular mat diameter sizes with various bucket spacings were considered and the results were compared with conventional tripod bucket foundation. Finite element models of the proposed foundation were developed and validated using experimental results and were used to conduct a parametric study to understand the behaviour of the hybrid tripod bucket foundation. The results showed that there is a significant increase in overturning capacity provided by the novel foundation. The results of this work can significantly improve lowering the costs associated with installation of foundations to support offshore wind turbines.     

Load-bearing behavior of suction bucket foundations in sand

Suction buckets are a promising foundation solution for offshore wind energy systems. The bearing behavior of monopod buckets under drained monotonic loading in very dense and medium dense sand is investigated in this study by means of numerical simulation with the finite element method. Special focus is given to the ultimate capacity and the initial stiffness of the bucket-soil foundation system. The numerical model is validated by comparison with field test results. The bearing behavior of the structure is explained through an evaluation of a reference system. It is shown that the bucket experiences a heave during horizontal loading, which leads to the formation of a gap between the bucket lid and the soil with increasing load. At large loads and rotations close to failure of the system there is no contact between lid and soil, and the whole load is transferred to the soil via the bucket skirt. A parametric study shows how the ultimate capacity and initial stiffness of the system depend on the bucket dimensions and loading conditions, i.e. load eccentricity. Normalized equations for ultimate capacity and initial stiffness are derived from the numerical simulation results, which can be used in the scope of a preliminary design for buckets in sand.     

Anisotropic deformation characteristics of soft marine clay involved the change of b-values and stress direction

In actual engineering, soft clay foundations are in drained or partial drained conditions, it would be useful to establish reasonable constitutive relationship and provide guidance for engineering projects. A hollow cylinder apparatus is used to investigate the anisotropic deformation behavior of natural soft marine clay influenced by intermediate principal stress coefficient b and principal stress direction α. Tests were conducted by maintaining a fixed principal stress direction α relative to the vertical direction, while keeping the intermediate principal stress coefficient b constant. It was found that the anisotropic deformation behavior of natural soft clay is merely influenced by major principal stress direction α, but significantly influenced by intermediate principal stress coefficient b.     

桶形基础及其作用下的粉质土海床失稳机制研究的试验设计

在阅读、分析以往的有关资料的基础上 ,结合实际的试验条件 ,对桶形基础及其作用下的粉质土海床失稳机制研究的试验作出了专门设计。该设计通过配土、设计模型桶基和负压沉贯的操作过程、设置孔压传感器等实验手段 ,努力从土体破坏的角度 ,寻求负压沉贯过程中沉贯负压、沉贯阻力及孔隙水压力之间的变化关系和确定桶基的上拔力。并且指出了数据处理的基本思路 ,以利于课题的深入研究。     

Mud mass transport due to waves based on an empirical rheology model featured by hysteresis loop

A vertical 2-D water–mud numerical model is developed for estimating the rate of mud mass transport under wave action. A nonlinear semi-empirical rheology model featured by remarkable hysteresis loops in the relationships of the shear stress versus both the shear strain and the rate of shear strain of mud is applied to this water–mud model. A logarithmic grid in the vertical direction is employed for numerical treatment, which increases the resolution of the flow in the neighborhood of both sides of the interface. Model verifications are given through comparisons between the calculated and the measured mud mass transport velocities as well as wave height changes.     

Stability analysis of suction bucket foundations under wave cyclic loading and scouring

Suction bucket foundation is a typical type for offshore turbines. Scour caused by wave and current can reduce the stability of foundation and then endanger the whole structure. This paper details a series of suction bucket model tests performed in sand under wave cyclic loading. The model tests investigate the effect of scour on stability of bucket foundation by artificially excavated scour hole around the foundation. It is revealed that the behavior of foundation bearing capacity can be divided into two stages: the initial cyclic stage and the final stage (showing either cyclic stability or cyclic failure). When the wave circulation is stable, the sand on the front and back sides of the foundation is suspected to be liquefied. With the increase in scour depth, the stability of foundation is gradually reduced, the behavior of foundation gradually changes from a state of cyclic stability to cyclic failure, and the number of waves that can be withstood is drastically reduced. Finally, the height of the center of rotation of the suction bucket was observed to descend with the increase in scour depth.