Azimuthally pre-stack seismic inversion for orthorhombic anisotropy driven by rock physics

Based on the long-wavelength approximation, a set of parallel vertical fractures embedded in periodic thin interbeds can be regarded as an equivalent orthorhombic medium. Rock physics is the basis for constructing the relationship between fracture parameters and seismic response. Seismic scattering is an effective way to inverse anisotropic parameters. In this study, we propose a reliable method for predicting the Thomsen’s weak anisotropic parameters and fracture weaknesses in an orthorhombic fractured reservoir using azimuthal pre-stack seismic data. First, considering the influence of fluid substitution in mineral matrix, porosity, fractures and anisotropic rocks, we estimate the orthorhombic anisotropic stiffness coefficients by constructing an equivalent rock physics model for fractured rocks. Further, we predict the logging elastic parameters, Thomsen’s weak parameters, and fracture weaknesses to provide the initial model constraints for the seismic inversion. Then, we derive the P-wave reflection coefficient equation for the inversion of Thomsen’s weak anisotropic parameters and fracture weaknesses. Cauchy-sparse and smoothing-model constraint regularization taken into account in a Bayesian framework, we finally develop a method of amplitude variation with angles of incidence and azimuth (AVAZ) inversion for Thomsen’s weak anisotropic parameters and fracture weaknesses, and the model parameters are estimated by using the nonlinear iteratively reweighted least squares (IRLS) strategy. Both synthetic and real examples show that the method can directly estimate the orthorhombic characteristic parameters from the azimuthally pre-stack seismic data, which provides a reliable seismic inversion method for predicting Thomsen’s weak anisotropic parameters and fracture weaknesses.     

基于贝叶斯线性AVAZ的TTI介质裂缝参数反演

裂缝储层岩石物理参数的准确获得对地下裂缝预测具有重要意义,而叠前方位AVA地震反演是获得裂缝岩石物理参数的有效手段.假设地下岩石为倾斜横向各向同性（TTI）介质,本文从裂缝岩石物理等效模型的构建出发,从测井数据中估计出纵横波相对反射系数和裂缝柔度参数.通过推导含裂缝柔度的方位各向异性反射系数公式,基于贝叶斯反演框架建立了P波线性AVAZ反演方法.合成地震数据应用表明基于贝叶斯理论的TTI介质裂缝柔度反演方法具有一定抗噪性,可以降低裂缝柔度估测的不确定性,为地下裂缝预测提供有力的依据.     

Amplitude variation with incident angle and azimuth inversion for Young's impedance,Poisson's ratio and fracture weaknesses in shale gas reservoirs

By analogy with P- and S-wave impedances, the product of Young's modulus and density can be termed as Young's impedance, which indicates the rock lithology and brittleness of unconventional hydrocarbon reservoirs. Poisson's ratio is also an effective indicator of rock brittleness and fluid property of unconventional reservoirs, and fracture weaknesses indicate the fracture properties (fracturing intensity and fracture fillings) in fracture-induced unconventional reservoirs. We aim to simultaneously estimate the Young's impedance, Poisson's ratio and fracture weaknesses from wide-azimuth surface seismic data in a fracture-induced shale gas reservoir, and use the horizontal transversely isotropic model to characterize the fractures. First, the linearized PP-wave reflection coefficient in terms of Young's impedance, Poisson's ratio, density and fracture weaknesses is derived for the case of a weak-contrast interface separating two weakly horizontal transversely isotropic media. In addition, an orthorhombic anisotropic case is also discussed in this paper. Then a Bayesian amplitude variation with incident angle and azimuth scheme with a model constraint is used to stably estimate Young's impedance, Poisson's ratio and fracture weaknesses with only PP-wave azimuthal seismic data. The proposed approach is finally demonstrated on both synthetic and real data sets with reasonable results.     

Seismic inversion for underground fractures detection based on effective anisotropy and fluid substitution

Underground fractures play an important role in the storage and movement of hydrocarbon fluid. Fracture rock physics has been the useful bridge between fracture parameters and seismic response. In this paper, we aim to use seismic data to predict subsurface fractures based on rock physics. We begin with the construction of fracture rock physics model. Using the model, we may estimate P-wave velocity, S-wave velocity and fracture rock physics parameters. Then we derive a new approximate formula for the analysis of the relationship between fracture rock physics parameters and seismic response, and we also propose the method which uses seismic data to invert the elastic and rock physics parameters of fractured rock. We end with the method verification, which includes using well-logging data to confirm the reliability of fracture rock physics effective model and utilizing real seismic data to validate the applicability of the inversion method. Tests show that the fracture rock physics effective model may be used to estimate velocities and fracture rock physics parameters reliably, and the inversion method is resultful even when the seismic data is added with random noise. Real data test also indicates the inversion method can be applied into the estimation of the elastic and fracture weaknesses parameters in the target area.     

Linearized amplitude variation with offset and azimuth and anisotropic poroelasticity

The normal-to-shear weakness ratio is commonly used as a fracture fluid indicator, but it depends not only on the fluid types but also on the fracture intensity and internal architecture. Amplitude variation with offset and azimuth is commonly used to perform the fluid identification and fracture characterization in fractured porous rocks. We demonstrate a direct inversion approach to utilize the observable azimuthal data to estimate the decoupled fluid (fluid/porosity term) and fracture (normal and shear weaknesses) parameters instead of the calculation of normal-to-shear weakness ratio to help reduce the uncertainties in fracture characterization and fluid identification of a gas-saturated porous medium permeated by a single set of parallel vertical fractures. Based on the anisotropic poroelasticity and perturbation theory, we first derive a linearized amplitude versus offset and azimuth approximation using the scattering function to decouple the fluid indicator and fracture parameters. Incorporating Bayes formula and convolution theory, we propose a feasible direct inversion approach in a Bayesian framework to obtain the direct estimations of model parameters, in which Cauchy and Gaussian distribution are used for the a priori information of model parameters and the likelihood function, respectively. We finally use the non-linear iteratively reweighted least squares to solve the maximum a posteriori solutions of model parameters. The synthetic examples containing a moderate noise demonstrate the feasibility of the proposed approach, and the real data illustrates the stabilities of estimated fluid indicator and dry fracture parameters in gas-saturated fractured porous rocks.     

Azimuthal Seismic Amplitude Variation with Offset and Azimuth Inversion in Weakly Anisotropic Media with Orthorhombic Symmetry

Seismic amplitude variation with offset and azimuth (AVOaz) inversion is well known as a popular and pragmatic tool utilized to estimate fracture parameters. A single set of vertical fractures aligned along a preferred horizontal direction embedded in a horizontally layered medium can be considered as an effective long-wavelength orthorhombic medium. Estimation of Thomsen’s weak-anisotropy (WA) parameters and fracture weaknesses plays an important role in characterizing the orthorhombic anisotropy in a weakly anisotropic medium. Our goal is to demonstrate an orthorhombic anisotropic AVOaz inversion approach to describe the orthorhombic anisotropy utilizing the observable wide-azimuth seismic reflection data in a fractured reservoir with the assumption of orthorhombic symmetry. Combining Thomsen’s WA theory and linear-slip model, we first derive a perturbation in stiffness matrix of a weakly anisotropic medium with orthorhombic symmetry under the assumption of small WA parameters and fracture weaknesses. Using the perturbation matrix and scattering function, we then derive an expression for linearized PP-wave reflection coefficient in terms of P- and S-wave moduli, density, Thomsen’s WA parameters, and fracture weaknesses in such an orthorhombic medium, which avoids the complicated nonlinear relationship between the orthorhombic anisotropy and azimuthal seismic reflection data. Incorporating azimuthal seismic data and Bayesian inversion theory, the maximum a posteriori solutions of Thomsen’s WA parameters and fracture weaknesses in a weakly anisotropic medium with orthorhombic symmetry are reasonably estimated with the constraints of Cauchy a priori probability distribution and smooth initial models of model parameters to enhance the inversion resolution and the nonlinear iteratively reweighted least squares strategy. The synthetic examples containing a moderate noise demonstrate the feasibility of the derived orthorhombic anisotropic AVOaz inversion method, and the real data illustrate the inversion stabilities of orthorhombic anisotropy in a fractured reservoir.     

基于方位各向异性弹性阻抗的裂缝岩石物理参数反演方法研究

裂缝储层岩石物理参数的准确获得对地下裂缝预测具有重要意义,而叠前地震反演是获得裂缝岩石物理参数的有效手段.本文从裂缝岩石物理等效模型的构建出发,从测井数据上估测了裂缝岩石物理参数,通过推导含裂缝岩石物理参数的方位各向异性弹性阻抗公式,探讨了基于方位各向异性弹性阻抗的裂缝岩石物理参数地震反演方法.实际工区地震数据应用表明,基于方位各向异性弹性阻抗的裂缝岩石物理参数反演方法合理、可靠,可以降低裂缝岩石物理参数估测的不确定性,为地下裂缝预测提供有力的依据.     

基于各向异性岩石物理的缝隙流体因子AVAZ反演

裂缝型储层表现出较强的各向异性特征.缝隙中充填不同流体时,裂缝储层的地震响应特征也不相同.本文从各向异性岩石物理模型出发,引入可有效识别缝隙流体的指示因子,并研究缝隙充填流体类型、饱和度以及缝隙纵横比与流体因子的相互关系,进而分析不同流体充填时介质的地震响应特征,并基于AVAZ反演方法估测缝隙流体指示因子.首先对缝隙流体因子的敏感性进行了分析,讨论当缝隙充填不同流体时,缝隙流体因子值的变化特征,同时研究了不同流体类型充填时裂缝储层反射系数随方位角和入射角的变化特征.某工区测井数据和复杂裂缝模型应用表明,基于各向异性岩石物理的缝隙流体因子AVAZ反演方法合理、可靠,且具有良好的抗噪性,即当对合成地震记录添加信噪比不小于1/2的随机噪声时,利用AVAZ反演方法估测所得流体因子值与真实值仍然吻合较好.     

Bayesian seismic inversion for estimating fluid content and fracture parameters in a gas-saturated fractured porous reservoir

Understanding the effects of in situ fluid content and fracture parameters on seismic characteristics is important for the subsurface exploration and production of fractured porous rocks. The ratio of normal-to-shear fracture compliance is typically utilized as a fluid indicator to evaluate anisotropy and identify fluids filling the fractures, but it represents an underdetermined problem because this fluid indicator varies as a function of both fracture geometry and fluid content. On the bases of anisotropic Gassmann's equation and linear-slip model, we suggest an anisotropic poroelasticity model for fractured porous reservoirs. By combining a perturbed stiffness matrix and asymptotic ray theory, we then construct a direct relationship between the PP-wave reflection coefficients and characteristic parameters of fluids(P-and S-wave moduli) and fractures(fracture quasi-weaknesses), thereby decoupling the effects of fluid and fracture properties on seismic reflection characterization.By incorporating fracture quasi-weakness parameters, we propose a novel parameterization method for elastic impedance variation with offset and azimuth(EIVOA). By incorporating wide-azimuth observable seismic reflection data with regularization constraints, we utilize Bayesian seismic inversion to estimate the fluid content and fracture parameters of fractured porous rocks. Tests on synthetic and real data demonstrate that fluid and fracture properties can be reasonably estimated directly from azimuthal seismic data and the proposed approach provides a reliable method for fluid identification and fracture characterization in a gas-saturated fractured porous reservoir.     

Rock skeleton models and seismic porosity inversion

By substituting rock skeleton modulus expressions into Gassmann approximate fluid equation, we obtain a seismic porosity inversion equation. However, conventional rock skeleton models and their expressions are quite different from each other, resuling in different seismic porosity inversion equations, potentially leading to difficulties in correctly applying them and evaluating their results. In response to this, a uniform relation with two adjusting parameters suitable for all rock skeleton models is established from an analysis and comparison of various conventional rock skeleton models and their expressions including the Eshelby-Walsh, Pride, Geertsma, Nur, Keys-Xu, and Krief models. By giving the two adjusting parameters specific values, different rock skeleton models with specific physical characteristics can be generated. This allows us to select the most appropriate rock skeleton model based on geological and geophysical conditions, and to develop more wise seismic porosity inversion. As an example of using this method for hydrocarbon prediction and fluid identification, we apply this improved porosity inversion, associated with rock physical data and well log data, to the ZJ basin. Research shows that the existence of an abundant hydrocarbon reservoir is dependent on a moderate porosity range, which means we can use the results of seismic porosity inversion to identify oil reservoirs and dry or water-saturated reservoirs. The seismic inversion results are closely correspond to well log porosity curves in the ZJ area, indicating that the uniform relations and inversion methods proposed in this paper are reliable and effective.     

Pore fluid viscosity effects on P‐ and S‐wave anisotropy in synthetic silica‐cemented sandstone with aligned fractures

Ultrasonic (500 kHz) P‐ and S‐wave velocity and attenuation anisotropy were measured in the laboratory on synthetic, octagonal‐shaped, silica‐cemented sandstone samples with aligned penny‐shaped voids as a function of pore fluid viscosity. One control (blank) sample was manufactured without fractures, another sample with a known fracture density (measured from X‐ray CT images). Velocity and attenuation were measured in four directions relative to the bedding fabric (introduced during packing of successive layers of sand grains during sample construction) and the coincident penny‐shaped voids (fractures). Both samples were measured when saturated with air, water (viscosity 1 cP) and glycerin (100 cP) to reveal poro‐visco‐elastic effects on velocity and attenuation, and their anisotropy. The blank sample was used to estimate the background anisotropy of the host rock in the fractured sample; the bedding fabric was found to show transverse isotropy with shear wave splitting (SWS) of 1.45 ± 1.18% (i.e. for S‐wave propagation along the bedding planes). In the fractured rock, maximum velocity and minimum attenuation of P‐waves was seen at 90° to the fracture normal. After correction for the background anisotropy, the fractured sample velocity anisotropy was expressed in terms of Thomsen's weak anisotropy parameters ε, γ & δ. A theory of frequency‐dependent seismic anisotropy in porous, fractured, media was able to predict the observed effect of viscosity and bulk modulus on ε and δ in water‐ and glycerin‐saturated samples, and the higher ε and δ values in air‐saturated samples. Theoretical predictions of fluid independent γ are also in agreement with the laboratory observations. We also observed the predicted polarisation cross‐over in shear‐wave splitting for wave propagation at 45° to the fracture normal as fluid viscosity and bulk modulus increases.     

Seismic characterization of reservoirs with multiple fracture sets using velocity and attenuation anisotropy data

Knowledge about the spatial distribution of the fracture density and the azimuthal fracture orientation can greatly help in optimizing production from fractured reservoirs. Frequency-dependent seismic velocity and attenuation anisotropy data contain information about the fractures present in the reservoir. In this study, we use the measurements of velocity and attenuation anisotropy data corresponding to different seismic frequencies and azimuths to infer information about the multiple fracture sets present in the reservoir. We consider a reservoir model with two sets of vertical fractures characterized by unknown azimuthal fracture orientations and fracture densities. Frequency-dependent seismic velocity and attenuation anisotropy data is computed using the effective viscoelastic stiffness tensor and solving the Christoffel equation. A Bayesian inversion method is then applied to measurements of velocity and attenuation anisotropy data corresponding to different seismic frequencies and azimuth to estimate the azimuthal fracture orientations and the fracture densities, as well as their uncertainties. Our numerical examples suggest that velocity anisotropy data alone cannot recover the unknown fracture parameters. However, an improved estimation of the unknown fracture parameters can be obtained by joint inversion of velocity and attenuation anisotropy data.     

岩石物理驱动的储层裂缝参数与物性参数概率地震反演方法

长波长假设条件下,各向同性背景地层中发育一组平行排列的垂直裂缝可等效为具有水平对称轴的横向各向同性（HTI）介质.基于不同观测方位的岩石地震响应特征变化,宽方位地震数据不仅可实现裂缝岩石弹性参数与各向异性参数的预测,同时也蕴含着丰富的孔隙度等储层物性参数信息.本文结合实际地震资料提出了贝叶斯框架下岩石物理驱动的储层裂缝参数与物性参数概率地震联合反演方法,首先基于AVAZ反演裂缝岩石的弹性参数与各向异性参数,并在此基础上通过统计岩石物理模型表征孔隙度、裂缝密度等各向异性介质储层参数与裂缝岩石参数的相互关联,并采用马尔科夫链蒙特卡洛（MCMC）抽样方法进行大量样本的随机模拟,使用期望最大化（EM）算法估计后验条件概率分布,最终寻找最大后验条件概率对应的孔隙度、裂缝密度等HTI裂缝介质储层参数即为反演结果.测井及实际地震数据处理表明,该方法能够稳定合理地从方位地震资料中获取裂缝岩石弹性参数与各向异性参数,并提供了一种较为可靠的孔隙度、裂缝密度等裂缝介质储层参数概率地震反演方法.     

Anisotropic azimuthal surface-wave inversion for a vertically fractured and transverse isotropy medium: Theory and examples from a controlled field experiment

Fractures in elastic media add compliance to a rock in the direction normal to the fracture strike. Therefore, elastic wave velocities in a fractured rock will vary as a function of the energy propagation direction relative to the orientation of the aligned fracture set. Anisotropic Thomson–Haskell matrix Rayleigh-wave equations for a vertically transverse isotropic media can be used to model surface-wave dispersion along the principal axes of a vertically fractured and transversely isotropic medium. Furthermore, a workflow combining first-break analysis and azimuthal anisotropic Rayleigh-wave inversion can be used to estimate P-wave and S-wave velocities, Thomsen's ε, and Thomsen's δ along the principal axes of the orthorhombic symmetry. In this work, linear slip theory is used to map our inversion results to the equivalent vertically fractured and transversely isotropic medium coefficients. We carried out this inversion on a synthetic example and a field example. The synthetic data example results show that joint estimation of S-wave velocities with Thomsen's parameters ε and δ along normal and parallel to the vertical fracture set is reliable and, when mapped to the corresponding vertically fractured and transversely isotropic medium, provides insight into the fracture compliances. When the inversion was carried out on the field data, results indicated that the fractured rock is more compliant in the azimuth normal to the visible fracture set orientation and that the in situ normal fracture compliance to tangential fracture compliance ratio is less than half, which implies some cementation may have occurred along the fractures. Such an observation has significant implications when modelling the transport properties of the rock and its strength. Both synthetic and field examples show the potential of azimuthal anisotropic Rayleigh-wave inversion as the method can be further expanded to a more general case where the vertical fracture set orientation is not known a priori.     

Characterization of fractured reservoirs using a consistent stiffness‐permeability model: focus on the effects of fracture aperture

In this paper we propose a method for the characterization of naturally fractured reservoirs by quantitative integration of seismic and production data. The method is based on a consistent theoretical frame work to model both effective hydraulic and elastic properties of fractured porous media and a (non‐linear) Bayesian method of inversion that provides information about uncertainties as well as mean (or maximum likelihood) values. We model a fractured reservoir as a porous medium containing a single set of vertical fractures characterized by an unknown fracture density, azimuthal orientation and aperture. We then look at the problem of fracture parameter estimation as a non‐linear inverse problem and try to estimate the unknown fracture parameters by joint inversion of seismic amplitude versus angle and azimuth data and dynamic production data. Once the fracture parameters have been estimated the corresponding effective stiffness and permeability tensors can be estimated using consistent models. A synthetic example is provided to clearly explain and test the workflow. It shows that seismic and production data complement each other, in the sense that the seismic data resolve a non‐uniqueness in the fracture orientation and the production data help to recover the true fracture aperture and permeability, because production data are more sensitive to the fracture aperture than the seismic data.     

非均质天然气藏的岩石物理模型及含气饱和度反演

非均质气藏中,天然气一般呈"斑块状"分布于含水岩石内部,这种非均匀分布特征会导致地震波显著的频散与衰减现象.为发展适用于碳酸盐岩储层中流体检测的岩石物理模型,本文基于Biot-Rayleigh波动方程,实现了对非饱和岩石的多尺度理论建模,预测了不同尺度下波响应与岩性、流体间的定量联系.将此项建模技术应用于阿姆河右岸的灰岩气藏,给出了多尺度的岩石物理学图板.通过与实验数据、测井精细解释结果及地震数据的对比分析,本文论证了图板的正确性与可适用性.结合叠后波阻抗反演与叠前弹性参数反演,基于地震资料进行了储层含气饱和度与孔隙度的反演,反演结果与各井实际的产气情况吻合.     

Constructing a discrete fracture network constrained by seismic inversion data

Rock fractures are of great practical importance to petroleum reservoir engineering because they provide pathways for fluid flow, especially in reservoirs with low matrix permeability, where they constitute the primary flow conduits. Understanding the spatial distribution of natural fracture networks is thus key to optimising production. The impact of fracture systems on fluid flow patterns can be predicted using discrete fracture network models, which allow not only the 6 independent components of the second‐rank permeability tensor to be estimated, but also the 21 independent components of the fully anisotropic fourth‐rank elastic stiffness tensor, from which the elastic and seismic properties of the fractured rock medium can be predicted. As they are stochastically generated, discrete fracture network realisations are inherently non‐unique. It is thus important to constrain their construction, so as to reduce their range of variability and, hence, the uncertainty of fractured rock properties derived from them. This paper presents the underlying theory and implementation of a method for constructing a geologically realistic discrete fracture network, constrained by seismic amplitude variation with offset and azimuth data. Several different formulations are described, depending on the type of seismic data and prior geologic information available, and the relative strengths and weaknesses of each approach are compared. Potential applications of the method are numerous, including the prediction of fluid flow, elastic and seismic properties of fractured reservoirs, model‐based inversion of seismic amplitude variation with offset and azimuth data, and the optimal placement and orientation of infill wells to maximise production.     

CO2 saturation estimates at Sleipner (North Sea) from seismic tomography and rock physics inversion

CO₂ saturations are estimated at Sleipner using a two-step imaging workflow. The workflow combines seismic tomography (full-waveform inversion) and rock physics inversion and is applied to a two-dimensional seismic line located near the injection point at Sleipner. We use baseline data (1994 vintage, before CO₂ injection) and monitor data that was acquired after 12 years of CO₂ injection (2008 vintage). P-wave velocity models are generated using the Full waveform inversion technology and then, we invert selected rock physics parameters using an rock physics inversion methodology. Full waveform inversion provides high-resolution P-wave velocity models both for baseline and monitor data. The physical relations between rock physics properties and acoustic wave velocities in the Utsira unconsolidated sandstone (reservoir formation) are defined using a dynamic rock physics model based on well-known Biot–Gassmann theories. For data prior to injection, rock frame properties (porosity, bulk and shear dry moduli) are estimated using rock physics inversion that allows deriving physically consistent properties with related uncertainty. We show that the uncertainty related to limited input data (only P-wave velocity) is not an issue because the mean values of parameters are correct. These rock frame properties are then used as a priori constraint in the monitor case. For monitor data, the Full waveform inversion results show nicely resolved thin layers of CO₂–brine saturated sandstones under intra-reservoir shale layers. The CO₂ saturation estimation is carried out by plugging an effective fluid phase in the rock physics model. Calculating the effective fluid bulk modulus of the brine–CO₂ mixture (using Brie equation in our study) is shown to be the key factor to link P-wave velocity to CO₂ saturation. The inversion tests are done with several values of Brie/patchiness exponent and show that the CO₂ saturation estimates are varying between 0.30 and 0.90 depending on the rock physics model and the location in the reservoir. The uncertainty in CO₂ saturation estimation is usually lower than 0.20. When the patchiness exponent is considered as unknown, the inversion is less constrained and we end up with values of exponent varying between 5 and 20 and up to 33 in specific reservoir areas. These estimations tend to show that the CO₂–brine mixing is between uniform and patchy mixing and variable throughout the reservoir.     

测井资料Xu-White模型预测横波速度的一些新观点

目前横波预测的方法大致可以分为两种:经验公式预测和理论岩石物理模型。由于经验公式预测一般具有区域性,研究者更重视岩石物理模型预测。目前大多数岩石物理模型预测横波的方法假定地下流体的物性参数(速度和密度)不受地层深度的影响,且孔隙扁率是恒定的,实际上这并不科学。因为矿物的体积模量和剪切模量随所处地层深度发生改变,而对于孔隙扁率则随颗粒形状、孔隙度等的变化有较大变化。针对这些情况,提出一种新的改进的Xu-White横波预测方法,并可取得较好的效果。     

Reconstruction of the layer anisotropic elastic parameters and high-resolution fracture characterization from P-wave data: a case study using seismic inversion and Bayesian rock physics parameter estimation

Wide-azimuth seismic data can be used to derive anisotropic parameters on the subsurface by observing variation in subsurface seismic response along different azimuths. Layer-based high-resolution estimates of components of the subsurface anisotropic elastic tensor can be reconstructed by using wide-azimuth P-wave data by combining the kinematic information derived from anisotropic velocity analysis with dynamic information obtained from amplitude versus angle and azimuth analysis of wide-azimuth seismic data. Interval P-impedance, S-impedance and anisotropic parameters associated with anisotropic fracture media are being reconstructed using linearized analysis assuming horizontal transverse anisotropy symmetry. In this paper it is shown how additional assumptions, such as the rock model, can be used to reduce the degrees of freedom in the estimation problem and recover all five anisotropic parameters. Because the use of a rock model is needed, the derived elastic parameters are consistent with the rock model and are used to infer fractured rock properties using stochastic rock physics inversion. The inversion is based on stochastic rock physics modelling and maximum a posteriori estimate of both porosity and crack density parameters associated with the observed elastic parameters derived from both velocity and amplitude versus angle and azimuth analysis. While the focus of this study is on the use of P-wave reflection data, we also show how additional information such as shear wave splitting and/or anisotropic well log data can reduce the assumptions needed to derive elastic parameter and rock properties.