ICP-MS测定海洋沉积物重金属微波消解条件的正交试验优化

准确测定海洋沉积物中重金属元素的含量,对于健康海洋的监测、维护和治理具有重要的指导意义。本文报道了电感耦合等离子体质谱法(ICP-MS)同时测定海洋沉积物中铜、锌、铅和镉四种元素微波密闭消解条件的正交试验优化结果。运用正交试验法,选取L16(45)正交表,按五因素四水平安排试验,研究不同酸体系和配比下,以及不同微波消解条件下沉积物样品的消解效果。经极差分析及方差分析后,得到海洋沉积物样品在称样量为0.05 g左右(精确到±0.000 1 g)情况下,最佳消解条件为HNO3(体积分数69%)用量6.0 mL、H_2O_2(体积分数30%)用量3.0 mL、HF(体积分数49%)用量3.0 mL、第三步程序消解温度190℃、保温时间15min。结果表明,正交优化后的方法准确度高,对三种有证海洋沉积物标准物质的测试均在标准值范围内;回收率好,各元素回收率在91.52%～107.55%之间;精密度高,重复性好,重复性的相对标准偏差为1.29%～8.21%;方法检出限低,各元素方法定量下限为0.005～0.057μg/g。该方法准确可靠,满足海洋沉积物样品中铜、锌、铅和镉等元素含量准确测定的测试需求。     

海带中12 种元素ICP-OES 检测的三种前处理方法对比研究

运用电感耦合等离子体发射光谱法(Inductively Coupled Plasma-Optical Emission Spectrometry,ICP-OES)比较研究了干法灰化、湿法消解和微波消解3种前处理方法对海带样品中Se、Fe、Mn、Zn、Ca、Mg、P、As、Cd、Cr、Cu和Pb 12种元素含量测定的影响。结果表明,不同前处理方法对微量元素的测定结果会产生不同程度的影响。干法灰化对易挥发元素As等带来明显的负误差;湿法消解由于加入的消解液量大,对低含量的微量元素常带来较大的试剂空白;微波消解法相对于其他两种前处理方法适于样品的快速消解,具有操作简便、试剂用量少、操作误差小等优点,检测结果具备较高的准确度、精密度和回收率,对海带样品微波消解ICP-OES检测的相对标准偏差为0.29%~2.63%,加标回收率为87.3%~103.6%。微波消解是海带等海洋生物样品中微量元素测定较理想的前处理方法。     

防腐高效溶样罐-ICP-MS测定海洋生物体中微量元素

为明确海洋生物体中微量元素的含量状况，开发了一种适合海洋生物体中微量元素准确测定的分析方法。研究采用防腐高效溶样罐对GBW08517（海带Saccharina japonica）与GBW08571（贻贝Mytilus coruscus Goyld）2种国内海洋生物标准物质进行2种不同前处理方法的消解实验，然后应用电感耦合等离子质谱仪（ICP-MS）测试了包括稀土元素在内的33个微量元素。实验结果表明，除个别元素外，测试结果均与标准值相符合，且前处理方法1消解的生物样品测试结果更加准确和稳定。使用防腐高效溶样罐优化了生物样品处理的消解方法，能有效去除生物样品中的有机基体，使ICP-MS充分发挥优势。与以往的消解方法相比，在生物消解中效果优于微波消解，前处理方法1还具有易操作、处理效率高、低试剂消耗、安全性强、避免样品污染等优点。     

ICP-MS测定聚碳酸酯塑料中锑及其不确定度评定

采用微波消解-电感耦合等离子体质谱法(ICP-MS)测定聚碳酸酯塑料中锑含量。考察了消解介质、消解样品量的选择对消解结果的影响,优化选择了电感藕合等离子体-质谱法(ICP-MS)的测定参数。在选定的最佳消解和测定条件下,称取0.200 0g聚碳酸酯塑料样品于5mL HNO3试剂下消解,实验相对标准偏差RSD为3.68%,对实验样品添加5.00ng/mL标准进行加标回收实验,加标回收率在95.1%~110.9%之间,检出限为0.022ng/mL。该方法具有准确、简便、快速等优点,可以满足聚碳酸酯触塑料材料中锑的检测要求。通过建立不确定性评定数学模型,分析了影响不确定度的主要来源,对样品质量、体积定容、仪器测量重复性、标准储备液、曲线拟合等影响不确定度的分量进行分析,最后计算出合成标准不确定度和扩展不确定度。ICP-MS法测试塑料中锑含量可以表示为(0.568±0.057)mg/kg,可使实验结果更具客观性和准确性。     

火焰原子吸收法测定海洋生物体中的铜、锌

一、前言 铜、锌是海洋环境监测重要项目之一。对海洋生物中铜、锌的测定,一般采用比色法和原子吸收法。但由于海洋生物样品基体复杂,待测元素含量变化较大,往往需要分离富集,同时取样量大,操作繁琐费时,容易沾污。为寻找一种较为简便的分析方法,本文在前人的基础上,提出用硝酸-过氧化氢湿法消解样品,火焰原子吸收法直接测定海洋生物中铜、锌,使操作大为简化,也减少了在操作过程中的沾污。本方法应用于海洋生物中铜、锌     

元素分析仪快速测定海洋沉积物TOC和TN的条件优化

报道了在优化样品前处理、燃烧温度、最小加氧量和最佳称样量的基础上,综合构建优化了直接固体进样varioMACRO cube元素分析仪同时测定海洋沉积物样品中总有机碳(TOC)和总氮(TN)的条件,即准确称取20~30 mg沉积物样品用1 mol/L盐酸除去无机碳后,直接进样在燃烧管温度960℃,次级燃烧管温度830℃,还原管温度900℃,氦气压力0.12 MPa,流量600 mL/min,氧气压力0.20 MPa,加氧量22.5 mL仪器条件下,用标准曲线法峰面积获取TOC和TN浓度。结果表明,海洋沉积物中TOC和TN测定的检出限分别为0.0508%和0.0146%,回收率分别为97.7%~100.9%和97.2%~101.1%,对4个实际外海沉积物样测定总有机碳和总氮结果的相对标准偏差(RSD)为0.83%~3.06%和1.33%~3.49%(n=12)。该方法操作简便快速、灵敏度高,具有较好的精密度和准确度,可准确可靠地用于海洋沉积物中总有机碳和总氮含量的测定。     

微波消解ICP-MS同时测定海产品中的15种元素含量

采用微波消解一电感耦合等离子体质谱(ICP-MS)法测定海产品中V,Cr,Mn,Fe,Co,Ni,Cu,Zn,As,Se,cd,Sn,Hg,Tl,Pb等15种元素的含量,以Re元素为内标,利用其回收率对以上15种元素的测定结果进行校正.对各元素的线性关系良好(r=0.999 1～1.000 0),检出限为0.28～1105μg/L,利用该方法分析了标准参考物质TORT-2和DORM-2,测定值与参考值吻合较好.对虾样品平行测定5次,各元素的RSD均小于5%,该方法的精密度和准确性良好.并以该方法分析测定了8种海产品中15种元素的含量.该方法可以用来进行海产品的质量控制和安全评价.     

高效液相色谱法测定食品中嘌呤含量

为测定食品中嘌呤含量,建立了食品中多组分嘌呤含量测定的反相离子对高效液相色谱(RP-IP-HPLC)分析方法,对几种主要食品中的腺嘌呤、鸟嘌呤、黄嘌呤、次黄嘌呤含量进行测定。结果表明,采用Agilent XDB-C18色谱柱,水-甲醇-冰乙酸-10%四丁基氢氧化铵(V/V/V/V,879/100/15/6)为流动相,检测波长为254nm,流速为1mL/min时4种嘌呤可完全分离。测得4种嘌呤物质的回收率在91.8%~108.7%之间,方法的相对标准偏差(RSD)为2.7%~6.5%。不同种类食品中嘌呤总含量由高到低依次为:动物肝脏、动物肌肉、果蔬、菌类和蛋类。     

X射线荧光光谱法测定海洋沉积物中的41种元素及氧化物

海洋沉积物样品具有盐分含量高、吸水性强、基体复杂、不同元素浓度差异悬殊等特点,其元素定量分析无论在样品前处理以及分析测试方法都有不少问题。特别是常微量元素很难用同一种方法进行测定,波长色散X射线荧光光谱可以很好的解决这一难题。因此,本文构建了粉末压片制样波长色散X射线荧光光谱法直接测定海洋沉积物样品中41种元素或其氧化物(Na_2O、MgO、Al_2O_3、SiO_2、P、S、Cl、K_2O、CaO、Fe_2O_3、Sc、Ti, V、Cr、Mn、Co、Ni、Cu、Zn、Ga、As、Br、Rb、Sr、Y、Zr、Nb、Mo、Cd、Sn、Sb、Ba、La、Hf、W、Pb、Bi、Ce、Nd、Th、U)的方法。样品在30 t的压力下保压30 s,制备的样片坚固光滑、吸潮性小。针对海洋地质样品的多样性,通过多种校准标准品拟合曲线进行测量,降低了检出限,优化了测量条件。用经验系数、理论α系数与经验系数相结合和康普顿散射线内标法校正元素间的基体效应。对土壤成分标准物质GBW07408和海洋沉积物成分标准物质GBW07315进行精密度考察,大部分元素的方法精密度提高至0.16%~3.87%,绝大多数主次痕量元素的测量精密度(RSD)小于4%,方法检出限为0.8~220μg/g。对渤海湾三个站位沉积物样品41种元素或其氧化物测定,结果表明,测定方法的重复性好,经国家一级标准物质验证,表明方法准确可靠,能满足日常分析要求。该方法对水系沉积物、土壤等陆地地化样品同样适用。     

电感耦合等离子体发射光谱法(ICP-OES)测定海洋浮游生物中总磷的方法优化

磷作为海洋浮游生物生长必需营养元素之一,其准确测定对海洋生态系统元素循环过程的研究具有重要意义。目前,文献中对于海洋浮游生物中总磷的测定方法报道不多。由于海洋浮游生物生存的高盐海洋环境,高盐基体的存在导致常规检测方法不能准确测定磷的含量。为剔除高盐基体效应及干扰,本文运用微波密闭消解预处理样品,采用电感耦合等离子体发射光谱法(ICP-OES)联合标准加入法建立工作曲线,同时结合样品的特异性,对ICP-OES分析谱线、射频功率、雾化气流速、观测高度、蠕动泵泵速和观测方式等仪器参数进行优化,构建确定了准确测定海洋浮游生物中总磷的优化条件和技术流程。实验结果显示, ICP-OES最佳工作条件为分析谱线P213.617 nm,射频功率1 300 W,雾化气流量0.8 L/min,观测高度14mm,进样泵速1.5 m L/min,观测方式轴向。标准加入法标准曲线相关系数大于0.999,相对标准偏差为1.36%~1.67%,加标回收率为92.6%~94.3%,方法检出限为0.010 mg/L,检测结果具有较高的准确度和精密度,可为海洋浮游生物及其它高基体生物样品中磷含量的准确测定提供技术支持。     

Assessing the Validity of Seismo-Acoustic Predictor Equations for Obtaining Seabed and Sub-Surface Sediment Physical Properties

The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths.     

海上大直径钢管桩打桩过程中桩周土强度弱化研究

海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。     

Interannual Sea Level Variations and Annual Tides in the Northwestern Pacific

Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone.     

Flow Cytometric Analysis of Coastal Lagoon Bacterioplankton and Picophytoplankton: Fixation and Storage Effects

The effect of different fixation and storage protocols on the flow cytometric (FCM) simultaneous analysis of bacterioplankton and phytoplankton in coastal seawater samples (Mediterranean coastal lagoons) was investigated. FCM measurements (cell number, fluorescence and scatter characteristics) were obtained through DAPI staining. Three fixatives [glutaraldehyde (GA), formaldehyde (FA) and paraformaldehyde (PFA)] and two storage (3 months duration) methods (5 °C and −196 °C) were tested. Two dominant populations were detected in studied samples: bacteria and eukaryotic picophytoplankton. Adding fixatives (2% final concentration) appears necessary to obtain FCM exhaustive counts of all the bacteria and phytoplanktonic cells. This was related to the permeation effect of fixatives which allowed a better DAPI staining of the cells. Maximum fluorescence, i.e. optimal staining of the cells was obtained with FA or PFA, and significant lower fluorescences with GA. Fixed samples stored at 5 °C induced rapid cell loss. Only storage in liquid nitrogen of samples fixed with FA or PFA, allows mid-term (≥4 months) preservation of bacteria or picophytoplankton cell numbers, and limited evolution of DAPI-induced fluorescence and scatter characteristics.     

INFORMATION FOR AUTHORS

<正>Acta Oceanologica Sinica(AOS)is a comprehensive academic journal edited by the Editorial Committee of Acta Oceanologica Sinica and is designed to provide a forum for important research papers of the marine scientific community which reflect the information on a worldwide basis.The journal publishes scholarly papers on marine science and technology,including physics,chemistry,biology,     

Phylogenetic diversity and phenotypic characterization of cultivable bacterioplankton isolated from polar oceans

A set of 27 marine planktonic bacteria isolated from the polar regions was characterized by 16S rDNA sequencing and physiological and biochemical testing. More than half of these bacteria were positive for caseinase, gelatinase and 13-glucosidase, and could utilize glucose, maltose or malic acid as carbon source for cell growth. Twelve isolates expressed nitrate reduction activities. Except for one antarctic isolate BSwlO175 belonging to Actinobacteria phylum, these isolates were classified as γ-Proteobacteria, suggesting that γ-Proteobacteria dominated in cultivable marine bacterioplankton at both poles. Genus Pseudoalteromonas was the predominant group in the Chukchi Sea and the Bering Sea, and genus ShewaneUa dominated in cultivable bacterioplankton in the Prydz Bay. With sequence similarities above 97%, genus Psychrobacter was found at both poles. These 27 isolates were psychrotolerant, and significant 16S rDNA sequence similarities were found not only between arctic and antarctic marine bacteria （ 〉 99% ）, but also between polar marine bacteria and bacteria from other aquatic environments （ ≥ 98.8% ）, including temperate ocean, deep sea, pond and lake, suggesting that in the polar oceans less temperature-sensitive bacteria may be cosmopolitan and have a bipolar, even global, distribution at the species level.     

Net Sand Transport Direction in a Tidal Inlet, using Foraminiferal Tests as Natural Tracers

The relationship between the flux of exotic benthic foraminiferal tests (i.e. tests which are supplied from open-sea sources alone) in a tidal inlet and that of bulk sediment was analysed, which can be expressed as two first-order linear equations. According to this relationship, in order to determine net sediment transport directions in the entrance, the test concentration in surficial sediments of the tidal basin can be compared against a ‘ critical level ’. The critical level is determined for the conditions that no net transport of bulk sediment is present within the entrance. If the observed concentration (averaged over the tidal basin) is higher than the simulated critical level, then the net sediment transport is directed to landward. This method is applied to the analysis of net sand transport at Christchurch Harbour, a tidal inlet system located in southern England. In this investigation, concentrations of exotic foraminiferal tests in the surficial sediments of the tidal basin and ebb tidal delta area were obtained from the analysis of sea-bed sediment samples. A series of probable critical levels were calculated based upon the data sets with regard to: (1) sediment discharge from the rivers; (2) magnitude of sediment discharge within the entrance during the ebb; (3) the test concentration outside the harbour; (4) the thickness of the moving layer; and (5) two parameters associated with dispersive processes. The results show that the concentration in the tidal basin sediment is higher than a number of simulated critical concentrations for representative cases. Consequently, the high level of the concentration of exotic benthic foraminiferal tests within the harbour should be explained as a result of landward net transport of sands within the entrance.