Bank undercutting and tension failure by groundwater seepage: predicting failure mechanisms

Groundwater seepage can lead to the erosion and failure of streambanks and hillslopes. Two groundwater instability mechanisms include (i) tension failure due to the seepage force exceeding the soil shear strength or (ii) undercutting by seepage erosion and eventual mass failure. Previous research on these mechanisms has been limited to non‐cohesive and low cohesion soils. This study utilized a constant‐head, seepage soil box packed with more cohesive (6% and 15% clay) sandy loam soils at prescribed bulk densities (1.30 to 1.70 Mg m^?3) and with a bank angle of 90° to investigate the controls on failure mechanisms due to seepage forces. A dimensionless seepage mechanism (SM) number was derived and evaluated based on the ratio of resistive cohesion forces to the driving forces leading to instability including seepage gradients with an assumed steady‐state seepage angle. Tension failures and undercutting were both observed dependent primarily on the saturated hydraulic conductivity, effective cohesion, and seepage gradient. Also, shapes of seepage undercuts for these more cohesive soils were wider and less deep compared to undercuts in sand and loamy sand soils. Direct shear tests were used to quantify the geotechnical properties of the soils packed at the various bulk densities. The SM number reasonably predicted the seepage failure mechanism (tension failure versus undercutting) based on the geotechnical properties and assumed steady‐state seepage gradients of the physical‐scale laboratory experiments, with some uncertainty due to measurement of geotechnical parameters, assumed seepage gradient direction, and the expected width of the failure block. It is hypothesized that the SM number can be used to evaluate seepage failure mechanisms when a streambank or hillslope experiences steady‐state seepage forces. When prevalent, seepage gradient forces should be considered when analyzing bank stability, and therefore should be incorporated into commonly used stability models. Copyright © 2013 John Wiley & Sons, Ltd.     

Soil properties controlling seepage erosion contributions to streambank failure

The majority of sediment leaving catchments may be from streambank failure. Seepage erosion of unconsolidated sand above a restrictive layer is an important erosion process in incised streams that leads to streambank failure by undercutting banks. The objective of this study was to determine the impact of soil properties on seepage erosion and the resulting streambank failure. Seepage flow and sediment concentrations were measured in situ at eight locations along the banks of a deeply incised stream in northern Mississippi. Using field observations as a guide, the soil profile conditions of a shallow (45 cm) streambank, consisting of 30 cm of topsoil, a 10 cm conductive layer, and a 5 cm restrictive layer, were mimicked in laboratory lysimeter experiments to quantify the hydrologic properties controlling seepage erosion and bank failure under a 40 cm head. The time to flow initiation and the flow rate were linearly related to the slope of the restrictive layer. Seepage erosion began within minutes of flow initiation and resulted in substantial (3 to 34 cm) undercutting of the bank. Sediment concentrations of seeps were as high as 660 g l^?1 in situ and 4500 g l^?1 in the lysimeters. Sediment concentrations were related to the layer slope, thereby indicating the importance of detailed site characterization. The USDA‐ARS Streambank Stability model demonstrated the increase in instability of banks due to undercutting by seepage erosion, but failed to account for the sediment loss due to sapping for stable banks and overestimated the sediment loads for failed banks. Published in 2006 by John Wiley & Sons, Ltd.     

Influence of seepage undercutting on the stability of root‐reinforced streambanks

Several mechanisms contribute to streambank failure including fluvial toe undercutting, reduced soil shear strength by increased soil pore‐water pressure, and seepage erosion. Recent research has suggested that seepage erosion of noncohesive soil layers undercutting the banks may play an equivalent role in streambank failure to increased soil pore‐water pressure. However, this past research has primarily been limited to laboratory studies of non‐vegetated banks. The objective of this research was to utilize the Bank Stability and Toe Erosion Model (BSTEM) in order to determine the importance of seepage undercutting relative to bank shear strength, bank angle, soil pore‐water pressure, and root reinforcement. The BSTEM simulated two streambanks: Little Topashaw Creek and Goodwin Creek in northern Mississippi. Simulations included three bank angles (70° to 90°), four pore‐water pressure distributions (unsaturated, two partially saturated cases, and fully saturated), six distances of undercutting (0 to 40 cm), and 13 different vegetation conditions (root cohesions from 0·0 to 15·0 kPa). A relative sensitivity analysis suggested that BSTEM was approximately three to four times more sensitive to water table position than root cohesion or depth of seepage undercutting. Seepage undercutting becomes a prominent bank failure mechanism on unsaturated to partially saturated streambanks with root reinforcement, even with undercutting distances as small as 20 cm. Consideration of seepage undercutting is less important under conditions of partially to fully saturated soil pore‐water conditions. The distance at which instability by undercutting became equivalent to instability by increased soil pore‐water pressure decreased as root reinforcement increased, with values typically ranging between 20 and 40 cm at Little Topashaw Creek and between 20 and 55 cm at Goodwin Creek. This research depicts the baseline conditions at which seepage undercutting of vegetated streambanks needs to be considered for bank stability analyses. Copyright © 2008 John Wiley & Sons, Ltd.     

Stochastic erosion of composite banks in alluvial river bends

The erosion of composite river banks is a complex process involving a number of factors including fluvial erosion, seepage erosion, and cantilever mass failure. To predict the rate of bank erosion with these complexities, a stochastic bank erosion model is suitable to define the probability distribution of the controlling variables. In this study, a bank erosion model in a river bend is developed by coupling several bank erosion processes with an existing hydrodynamic and morphological model. The soil erodibility of cohesive bank layers was measured using a submerged jet test apparatus. Seasonal bank erosion rates for four consecutive years at a bend in the Brahmaputra River, India, were measured by repeated bankline surveys. The ability of the model to predict erosion was evaluated in the river bend that displayed active bank erosion. In this study, different monsoon conditions and the distribution functions of two variables were considered in estimating the stochastic bank erosion rate: the probability of the soil erodibility and stochastic stage hydrographs for the nth return period river stage. Additionally, the influences of the deflection angle of the streamflow, longitudinal slope of river channel, and bed material size on bank erosion rate were also investigated. The obtained stochastic erosion predictions were compared with the observed distribution of the annual‐average bank erosion rate of 45 river bends in the Brahmaputra River. The developed model appropriately predicted the short‐term morphological dynamics of sand‐bed river bends with composite banks. Copyright © 2014 John Wiley & Sons, Ltd.     

Experimental investigation on cohesionless sandy bank failure resulting from water level rising

In the last decade, sediment replenishment forming cohesionless sandy banks below dams has become an increasingly common practice in Japan to compensate for sediment deficits downstream. The erosion process of the placed cohesionless sediment is a combination of lateral toe-erosion and the following mass failure. To explore cohesionless bank failure mechanisms, a series of experiments was done in a soil tank using a compacted sandy soil mass exposed to an increasing water level. Two types of uniform sand(D_(50) = 0.40 mm and 0.17 mm) and two bank heights(50 cm and 25 cm) were used under the condition of a constant bank slope of 75°. The three dimensional(3D) geometry of the bank after failure was measured using a handheld 3D scanner. The motion of bank failure was captured using the particle image velocimetry(PIV) technique, and the matric suction was measured by tensiometers. The compacted sandy soil was eroded by loss of matric suction accompanying the rise in water level which subsequently caused rotational slide and cantilever toppling failure due to destabilization of the bank. The effect of erosion protection resulting from the slumped blocks after these failures is discussed in the light of different failure mechanisms. Tensile strength is analyzed by inverse calculation of cantilever toppling failure events. The tensile strength had non-linear relation with degree of saturation and showed a peak.The findings of the study show that it is important to incorporate the non-linear relation of tensile strength into stability analysis of cantilever toppling failure and prediction of tension crack depth within unsaturated cohesionless banks.     

Magnitude and processes of bank erosion at a small stream in Denmark

River banks are important sources of sediment and phosphorus to fluvial systems, and the erosion processes operating on the banks are complex and change over time. This study explores the magnitude of bank erosion on a cohesive streambank within a small channelized stream and studies the various types of erosion processes taking place. Repeat field surveys of erosion pin plots were carried out during a 4‐year period and observations were supplemented by continuous monitoring of volumetric soil water content, soil temperature, ground water level and exposure of a PEEP sensor. Bank erosion rates (17·6–30·1 mm year^?1) and total P content on the banks were relatively high, which makes the bank an important source of sediment and phosphorus to the stream, and it was estimated that 0·27 kg P_tot year^?1 ha^?1 may potentially be supplied to the stream from the banks. Yearly pin erosion rates exceeding 5 cm year^?1 were mainly found at the lower parts of the bank and were associated with fluvial erosion. Negative erosion pin readings were widespread with a net advance of the bank during the monitoring period mainly attributed to subaerial processes and bank failure. It was found that dry periods characterized by low soil water content and freeze–thaw cycles during winter triggered bank failures. The great spatial variability, in combination with the temporal interaction of processes operating at different scales, requires new tools such as 3‐D topographical surveying to better capture bank erosion rates. An understanding of the processes governing bank erosion is required for riparian management using vegetational measures as root size and structure play different roles when it comes to controlling bank erosion processes. Copyright © 2010 John Wiley & Sons, Ltd.     

Experimental study of rill bank collapse

Rill bank collapse is an important component in the adjustment of channel morphology to changes in discharge and sediment flux. Sediment inputs from bank collapse cause abrupt changes in flow resistance, flow patterns and downstream sediment concentrations. Generally, bank retreat involves gradual lateral erosion, caused by flow shear stress, and sudden bank collapse, triggered by complex interactions between channel flow and bank and soil water conditions. Collapse occurs when bank height exceeds the critical height where gravitational forces overcome soil shear strength. An experimental study examined conditions for collapse in eroding rill channels. Experiments with and without a deep water table were carried out on a meandering rill channel in a loamy sand and sandy loam in a laboratory flume under simulated rainfall and controlled runon. Different discharges were used to initiate knickpoint and rill incision. Soil water dynamics were monitored using microstandpipes, tensiometers and time domain reflectometer probes (TDR probes). Bank collapse occurred with newly developed or rising pre‐existing water tables near rill banks, associated with knickpoint migration. Knickpoint scour increased effective bank height, caused positive pore water pressure in the bank toe and reduced negative pore pressures in the unsaturated zone to near zero. Matric tension in unsaturated parts of the bank and a surface seal on the ‘interrill’ zone behind the bank enhanced stability, while increased effective bank height and positive pore water pressure at the bank toe caused instability. With soil water contents >35 per cent (sandy loam) and >23 per cent (loamy sand), critical bank heights were 0·11–0·12 m and 0·06–0·07 m, respectively. Bank toe undercutting at the outside of the rill bends also triggered instability. Bank displacement was quite different on the two soils. On the loamy sand, the failed block slid to the channel bed, revealing only the upper half of the failure plane, while on the sandy loam the failed block toppled forwards, exposing the failure plane for the complete bank height. This study has shown that it is possible to predict location, frequency and magnitude of the rill bank collapse, providing a basis for incorporation into predictive models for hillslope soil loss or rill network development. Copyright © 2006 John Wiley & Sons, Ltd.     

Bank‐collapse processes in a valley‐bottom gully,western Iowa

Widening and bank‐slope reduction of a valley‐bottom gully in western Iowa was correlated to increasing subsurface flow over a 36‐year period. To study bank collapse at this gully, we measured rainfall, air temperature, hydraulic head near the banks and bank movement nearly continuously over a 2‐year period. Styles of movement ranged from imperceptible creep to rapid slab collapses preceded by the formation of tension cracks parallel to the gully walls. Bank movement was commonly correlated to rainfall or snowmelt and associated head increases in the banks. If the banks are modelled as a two‐dimensional slab with an adjacent tension crack partly filled with water, measured heads were sufficient to cause bank failures through reduction of frictional support at the base of the slab. During winter months, air temperature variations across 0 °C were correlated with bank movement: during mildly subfreezing periods banks expanded, and most, but usually not all, of this movement was recovered during above‐freezing periods. This motion is attributed to frost heave followed by thawing. Deformation of the banks by heaving and thawing during winter may weaken them and prime them for failure during spring rains and snowmelt, when the frequency of mass‐wasting events is highest. Copyright © 2008 John Wiley and Sons, Ltd.     

A large weighing lysimeter for evapotranspiration and soil‐water–groundwater exchange studies

A large weighing lysimeter was installed at Yucheng Comprehensive Experimental Station, north China, for evapotranspiration and soil‐water–groundwater exchange studies. Features of the lysimeter include the following: (i) mass resolution equivalent to 0·016 mm of water to accurately and simultaneously determine hourly evapotranspiration, surface evaporation and groundwater recharge; (ii) a surface area of 3·14 m² and a soil profile depth of 5·0 m to permit normal plant development, soil‐water extraction, soil‐water–groundwater exchanges, and fluctuations of groundwater level; (iii) a special supply–drainage system to simulate field conditions of groundwater within the lysimeter; (iv) a soil mass of about 30 Mg, including both unsaturated and saturated loam. The soil consists mainly of mealy sand and light loam. Monitoring the vegetated lysimeter during the growing period of winter wheat, from October 1998 through to June 1999, indicated that during the period groundwater evaporation contributed 16·6% of total evapotranspiration for a water‐table depth from 1·6 m to 2·4 m below ground surface. Too much irrigation reduced the amount of upward water flow from the groundwater table, and caused deep percolation to the groundwater. Data from neutron probe and tensiometers suggest that soil‐water‐content profiles and soil‐water‐potential profiles were strongly affected by shallow groundwater. Copyright © 2000 John Wiley & Sons, Ltd.     

Critical caving erosion width for cantilever failures of river bank

The cantilever failure is one of the typical bank failures, in which the lateral caving erosion at the bottom of the bank plays an important role. When the caving erosion width is larger than a certain value, the cantilever failures such as shear, toppling and stress failures may occur. In order to understand the condition of the cantilever failure, the collapse mechanisms of the cantilever failures are studied based on the bank stability theory and flume experiment. According to the bank stability equation with the lateral erosion, the critical caving erosion width (CCEW) formulas for the shear and toppling failures of simple slope bank were derived in this paper. The formulas show that the CCEW increases as the overhanging soil thickness and soil cohesion increase, and decreases as the crack depth on the bank surface and the slope angle of the bank increase. And these formulas were tested with experimental data, which shows the predicted values are good agreement with experimental data. The paper reveals a quantitative expression on the process of the river cantilever failure.     

Effects of riparian vegetation on stream bank subaerial processes in southwestern Virginia,USA

Riparian vegetation is frequently used for stream bank stabilization, but the effects of vegetation on subaerial processes have not been quantified. Subaerial processes, such as soil desiccation and freeze–thaw cycling, are climate‐related phenomena that deliver soil directly to the stream and make the banks more vulnerable to fluvial erosion by reducing soil strength. This study compares the impact of woody and herbaceous vegetation on subaerial processes by examining soil temperature and moisture regimes in vegetated stream banks. Soil temperature and water tension were measured at six paired field sites in southwestern Virginia, USA, for one year. Results showed that stream banks with herbaceous vegetation had higher soil temperatures and a greater diurnal temperature range during the summer compared to forested stream banks. Daily average summer soil water tension was 13 to 57 per cent higher under herbaceous vegetation than under woody vegetation, probably due to evapotranspiration from the shallow herbaceous root system on the bank. In contrast to summer conditions, the deciduous forest buffers provided little protection for stream banks during the winter: the forested stream banks experienced diurnal temperature ranges two to three times greater than stream banks under dense herbaceous cover and underwent as many as eight times the number of freeze–thaw cycles. During the winter, the stream banks under the deciduous forests were exposed to solar heating and night time cooling, which increased the diurnal soil temperature range and the occurrence of freeze–thaw cycling. Study results also indicated that freeze–thaw cycling and soil desiccation were greater on the upper stream bank due to thermal and moisture regulation of the lower bank by the stream. Therefore, subaerial erosion and soil weakening may be greater on the upper stream banks. Additional research is needed on the influence of subaerial processes on both subaerial and fluvial erosion. Copyright © 2006 John Wiley & Sons, Ltd.     

A new model to analyse the impact of woody riparian vegetation on the geotechnical stability of riverbanks

We present a geotechnical stability analysis for the planar failure of riverbanks, which incorporates the effects of root reinforcement and surcharge for mature stands of woody riparian vegetation. The analysis relies on a new method of representing the root distribution in the soil, which evaluates the effects of the vegetation's position on the bank. The model is used in a series of sensitivity analyses performed for a wide range of bank morphological (bank slope and height) and sedimentological (bank cohesion and friction angle) conditions, enabling discrimination of the types of bank environment for which vegetation has an effect on bank stability. The results indicate that woody vegetation elements have a maximal impact on bank stability when they are located at the ends of the incipient failure plane (i.e. at the bank toe or at the intersection of the failure plane with the floodplain) and that vegetation has a greater effect on net bank stability when it is growing on low, shallow, banks comprised of weakly cohesive sediments. However, the magnitude of these effects is limited, with vegetation typically inducing changes (relative to non‐vegetated banks) in simulated factors of safety of less than 5%. If correct, this suggests that the well documented effects of vegetation on channel morphology must be related to alternative process mechanisms (such as the interaction of vegetation with river flows) rather than the mechanical effects of vegetation on bank failure, except in special cases where the equivalent non‐vegetated bank has a highly marginal stability status. Copyright © 2007 John Wiley & Sons, Ltd.     

Ground‐based thermal imagery as a simple,practical tool for mapping saturated area connectivity and dynamics

The hillslope‐riparian‐stream system is a key functional unit of catchments, yet very difficult to measure and monitor due to its tremendous complexity and high spatio‐temporal variability. Here, we present a simple and practical tool for imaging directly these hillslope‐riparian‐area connections. We used a FLIR b50 infrared camera to produce thermal images at the scale of 140 × 140 pixels over the spectral range 7·5–13 µm. Our IR imaging technique is sensitive to the upper 0·1 mm of the water column. Images were obtained from a constant position on the right bank of the Weierbach catchment in Luxembourg, at an incidence angle of approximately 45° over a 5‐week period. The study site measured 5 × 3 m. Our results show that ground‐based IR imagery can discriminate between areas with snow cover, snow melt, soil seepage, and stream water. More importantly, it can detect when and where variably saturated areas are active and when connectivity exists between the hillslope–riparian–stream system. Our proof of concept suggests that this is a simple, inexpensive technology for sequential mapping and characterisation of surface saturated areas and a useful complement to conventional tracer techniques. Copyright © 2010 John Wiley & Sons, Ltd.     

Mechanisms of riverbank failure along the Arno River,central Italy

Riverbanks along the Arno River have been investigated with the aims of de?ning the main mechanisms of failure and retreat, their spatial distribution, and their causes. Geomorphological aspects were investigated by a reconnaissance of riverbank processes, for a number (26) of representative sites. Laboratory and in situ tests were then performed on a selected number of riverbanks (15). Based on the material characteristics, six main typologies of riverbanks have been de?ned, with homogeneous ?ne‐grained and composite banks representing the most frequent types. Slab‐type failures are the most frequent mechanism observed on ?ne‐grained banks, while cantilever failures prevail on composite banks. The role of river stage and related pore water pressure distributions in triggering the main observed mechanisms of failure has been investigated using two different types of stability analysis. The ?rst was conducted for 15 riverbanks, using the limit equilibrium method and considering simpli?ed hypotheses for pore water pressure distribution (annulment of negative pore pressures in the portion of the bank between low water stage and peak stage). Stability conditions and predicted mechanisms of failure are shown to be in reasonably good agreement with ?eld observations. Three riverbanks, representative of the main alluvial reaches of the river, were then selected for a more detailed bank stability analysis, consisting of: (a) de?nition of characteristic hydrographs of the reach with different return periods; (b) modelling of saturated and unsaturated ?ow using ?nite element seepage analysis; and (c) stability analysis with the limit equilibrium method, by adopting pore water pressure values derived from the seepage analysis. The results are compared to those obtained from the previous simpli?ed analysis, and are used to investigate the different responses, in terms of stability, to different hydrological and riverbank conditions. Copyright © 2003 John Wiley & Sons, Ltd.     

Significance of geomorphological and subsurface drainage controls on failures of peat‐covered hillslopes triggered by extreme rainfall

On 19 September 2003, 40 landslides of 140–18 000 m³ volume occurred within 2·5 km² on the slopes of Dooncarton Mountain (Republic of Ireland) during a storm that may have exceeded 90 mm within 90 minutes. The landslides were investigated to determine the reasons for such a high density of slope failures. All of the landslides were surveyed within four months, and nine of them were investigated in detail. The six largest landslides, all peat failures, accounted for 57% of the more than 100 000 m³ of material displaced during the event. A consistent sequence of superficial materials was found on the failed hillslopes, including an extensive iron pan at the base of a buried soil horizon 0·3 m below the base of the peat. Morphologically, almost all of the landslides occurred on steep planar slopes or around sharp convexities, with the latter failures developing retrogressively upslope. The only significant relationship found from analysis of 371 subsurface pipes and 142 seepage cracks (defined here as contiguous fissures conducting concentrated subsurface flow) across all the failures was that the thinner the peat cover, the deeper the pipes and seepage cracks occurred below the base of peat. It is concluded that most of the landslides were probably caused by a combination of excess water pressures in the buried soil horizon and the thinner overburden of peat or peaty soil associated with the steeper slope segments. Pipes and seepage cracks formed on the iron pan probably existed prior to the failure event and may have contributed to the high water pressures as rainwater inputs exceeded their discharge capacities. One large peat slide was probably triggered by excess water pressures developed within and between artificial tine cuts. The properties of the blanket peat were generally of little consequence in the occurrence of the landslides, but relict desiccation cracks and other structural weaknesses through the peat mass were probably highly significant. Although several aspects of the peat failures correspond to previously published examples, the context of these failures in terms of the topography and upland catena is distinctive. Copyright © 2007 John Wiley & Sons, Ltd.     

Measuring streambank erosion due to ground water seepage: correlation to bank pore water pressure,precipitation and stream stage

Limited information exists on one of the mechanisms governing sediment input to streams: streambank erosion by ground water seepage. The objective of this research was to demonstrate the importance of streambank composition and stratigraphy in controlling seepage flow and to quantify correlation of seepage flow/erosion with precipitation, stream stage and soil pore water pressure. The streambank site was located in Northern Mississippi in the Goodwin Creek watershed. Soil samples from layers on the streambank face suggested less than an order of magnitude difference in vertical hydraulic conductivity (K_s) with depth, but differences between lateral K_s of a concretion layer and the vertical K_s of the underlying layers contributed to the propensity for lateral flow. Goodwin Creek seeps were not similar to other seeps reported in the literature, in that eroded sediment originated from layers underneath the primary seepage layer. Subsurface flow and sediment load, quantified using 50 cm wide collection pans, were dependent on the type of seep: intermittent low‐flow (LF) seeps (flow rates typically less than 0·05 L min^?1), persistent high‐flow (HF) seeps (average flow rate of 0·39 L min^?1) and buried seeps, which eroded unconsolidated bank material from previous bank failures. The timing of LF seeps correlated to river stage and precipitation. The HF seeps at Goodwin Creek began after rainfall events resulted in the adjacent streambank reaching near saturation (i.e. soil pore water pressures greater than ?5 kPa). Seep discharge from HF seeps reached a maximum of 1·0 L min^?1 and sediment concentrations commonly approached 100 g L^?1. Buried seeps were intermittent but exhibited the most significant erosion rates (738 g min^?1) and sediment concentrations (989 g L^?1). In cases where perched water table conditions exist and persistent HF seeps occur, seepage erosion and bank collapse of streambank sediment may be significant. Copyright © 2007 John Wiley & Sons, Ltd.     

Uncertainty and sensitivity in a bank stability model: implications for estimating phosphorus loading

Eutrophication of aquatic ecosystems is one of the most pressing water quality concerns in the United States and around the world. Bank erosion has been largely overlooked as a source of nutrient loading, despite field studies demonstrating that this source can account for the majority of the total phosphorus load in a watershed. Substantial effort has been made to develop mechanistic models to predict bank erosion and instability in stream systems; however, these models do not account for inherent natural variability in input values. To quantify the impacts of this omission, uncertainty and sensitivity analyses were performed on the Bank Stability and Toe Erosion Model (BSTEM), a mechanistic model developed by the US Department of Agriculture – Agricultural Research Service (USDA‐ARS) that simulates both mass wasting and fluvial erosion of streambanks. Generally, bank height, soil cohesion, and plant species were found to be most influential in determining stability of clay (cohesive) banks. In addition to these three inputs, groundwater elevation, stream stage, and bank angle were also identified as important in sand (non‐cohesive) banks. Slope and bank height are the dominant variables in fluvial erosion modeling, while erodibility and critical shear stress had low sensitivity indices; however, these indices do not reflect the importance of critical shear stress in determining the timing of erosion events. These results identify important variables that should be the focus of data collection efforts while also indicating which less influential variables may be set to assumed values. In addition, a probabilistic Monte‐Carlo modeling approach was applied to data from a watershed‐scale sediment and phosphorus loading study on the Missisquoi River, Vermont to quantify uncertainty associated with these published results. While our estimates aligned well with previous deterministic modeling results, the uncertainty associated with these predictions suggests that they should be considered order of magnitude estimates only. Copyright © 2016 John Wiley & Sons, Ltd.     

How hydrological factors initiate instability in a model sandy slope

Knowledge of the mechanisms of rain‐induced shallow landslides can improve the prediction of their occurrence and mitigate subsequent sediment disasters. Here, we examine an artificial slope's subsurface hydrology and propose a new slope stability analysis that includes seepage force and the down‐slope transfer of excess shear forces. We measured pore water pressure and volumetric water content immediately prior to a shallow landslide on an artificial sandy slope of 32°: The direction of the subsurface flow shifted from downward to parallel to the slope in the deepest part of the landslide mass, and this shift coincided with the start of soil displacement. A slope stability analysis that was restricted to individual segments of the landslide mass could not explain the initiation of the landslide; however, inclusion of the transfer of excess shear forces from up‐slope to down‐slope segments improved drastically the predictability. The improved stability analysis revealed that an unstable zone expanded down‐slope with an increase in soil water content, showing that the down‐slope soil initially supported the unstable up‐slope soil; destabilization of this down‐slope soil was the eventual trigger of total slope collapse. Initially, the effect of apparent soil cohesion was the most important factor promoting slope stability, but seepage force became the most important factor promoting slope instability closer to the landslide occurrence. These findings indicate that seepage forces, controlled by changes in direction and magnitude of saturated and unsaturated subsurface flows, may be the main cause of shallow landslides in sandy slopes. Copyright © 2013 John Wiley & Sons, Ltd.     

Bank erodibility of shallow sandbed streams

Cross-sections were surveyed at straight reaches of 16 sandbed streams in the midwestern U.S. Two stratigraphic horizons are found in the banks at each site, an upper cohesive unit usually composed of silt and clay, and a lower unit composed of sand. Bank erosion on these rivers occurs when the upper cohesive unit is undercut by scour at bends. The overhanging cohesive block fails by toppling forward into the channel. During failure, the soil is primarily in tension rather than compression or shear. Analysis of this failure mechanism leads to a field method for measuring the tensile strength of riverbanks. Measured values of the tensile strength are not correlated with the channel geometry. Thus, the erodibility of the cohesive bank sediments does not influence the geometry of the rivers studied.     

Impacts of river bank stabilization using riprap on fish habitat in two contrasting environments

Riverbank stabilization using rock riprap is commonly used for protecting road and bridge structures from fluvial erosion. However, little is known about how streams adjust to such perturbation or how this can affect fish habitat in different fluvial environments, particularly for non‐salmonid species in small streams. The objective of this study is to assess impacts of riprap on fish habitat quantity and quality through a pairwise comparison of 27 stabilized and non‐stabilized stream reaches in two physiographic regions, the Saint Lawrence Lowlands and the Appalachian highlands of Montérégie‐Est (Quebec, Canada). Both quantitative (Hydro‐morphological Index of Diversity, HMID) and qualitative (Qualitative Habitat Evaluation Index, QHEI) fish habitat assessment techniques are applied in order to compare results between methods. For each stream reach depth and velocity were measured to calculate HMID. In‐stream cover (woody debris, overhanging vegetation, undercut banks, aquatic macrophytes) and habitat units (pools, riffles, runs, glides) were also documented and used to determine QHEI. Results show that overall bank stabilization using riprap at bridge and stream crossings alters fish habitat characteristics. Loss of in‐stream covers and riparian vegetation lower QHEI scores at stabilized reaches, especially in more pristine Appalachian streams, but has less impact on already altered straightened Lowlands streams. In this latter context, some positive alterations of fish habitat were observed in riprapped reaches due to the coarsening of the substrate and an induced increase of slope. The two metrics (HMID and QHEI) revealed similar differences between stabilized and non‐stabilized sites for Lowlands sites, but their level of agreement was much less in the Appalachian streams, suggesting caution when interpreting habitat quality results based on a single metric. Copyright © 2016 John Wiley & Sons, Ltd.