Field evidences from northern Dead Sea Fault Zone (South Turkey): New findings for the initiation age and slip rate

The left-lateral strike–slip Dead Sea Fault Zone (DSFZ) extends from the Red Sea in the south to the East Anatolian Fault Zone (EAFZ) in the north. This study examines the northern part of the DSFZ around Amik Basin and presents surface and subsurface geological evidence for the Quaternary activity and initiation age of the northernmost DSFZ. The DSFZ extends N–S in the south of the Amik Basin where clear geological and morphological evidence exists for faulting. Geological observations around Amik Basin, analyses of borehole data and electrical resistivity profiles within the Amik Basin indicate that the activity of the northern DSFZ started after Pliocene in the Amik Basin. Subsurface data in the basin suggest that the DSFZ offsets a pre-Quaternary basin sinistrally by about 7.9 km. The offset pre-Quaternary basin suggests at least 4.94 ± 0.13 mm/year slip rate for the northern part of the DSFZ. The Karasu Fault Zone (KFZ) extends in an en-echelon pattern along the western margin of the Karasu Valley and it transfers the significant amount of slip from DSFZ to the EAFZ.     

Rate of strike-slip motion on the Amanos Fault (Karasu Valley, southern Turkey) constrained by K–Ar dating and geochemical analysis of Quaternary basalts

The left-lateral Amanos Fault follows a 200-km-long and up to 2-km-high escarpment that bounds the eastern margin of the Amanos mountain range and the western margin of the Karasu Valley in southern Turkey, just east of the northeastern corner of the Mediterranean Sea. Regional kinematic models have reached diverse conclusions as to the role of this fault in accommodating relative motion between either the African and Arabian, Turkish and African, or Turkish and Arabian plates. Local studies have tried to estimate its slip rate by K–Ar dating Quaternary basalts that erupted within the Amanos Mountains, flowed across it into the Karasu Valley, and have since become offset. However, these studies have yielded a wide range of results, ranging from 0.3 to 15 mm a⁻¹, which do not allow the overall role and significance of this fault in accommodating crustal deformation to be determined. We have used the Cassignol K–Ar method to date nine Quaternary basalt samples from the vicinity of the southern part of the Amanos Fault. These basalts exhibit a diverse chemistry, which we interpret as a consequence varying degrees of partial melting of their source combined with variable crustal contamination. This dating allows us to constrain the Quaternary slip rate on the Amanos fault to 1.0 to 1.6 mm a⁻¹. The dramatic discrepancies between past estimates of this slip rate are partly due to technical difficulties in K–Ar dating of young basalts by isotope dilution. In addition, previous studies at the key locality of Hacılar have unwittingly dated different, chemically distinct, flow units of different ages that are juxtaposed. This low slip rate indicates that, at present, the Amanos Fault takes up a small proportion of the relative motion between the African and Arabian plates, which is transferred southward to the Dead Sea Fault Zone. It also provides strong evidence against the long-standing view that its slip continues offshore to the southwest along a hypothetical left-lateral fault zone located south of Cyprus.     

Neotectonic and volcanic characteristics of the Karasu fault zone (Anatolia,Turkey): The transition zone between the Dead Sea transform and the East Anatolian fault zone

The Karasu Rift (Antakya province, SE Turkey) has developed between east-dipping, NNE-striking faults of the Karasu fault zone, which define the western margin of the rift and west-dipping, N–S to N20°–30°E-striking faults of Dead Sea Transform fault zone (DST) in the central part and eastern margin of the rift. The strand of the Karasu fault zone that bounds the basin from west forms a linkage zone between the DST and the East Anatolian fault zone (EAFZ). The greater vertical offset on the western margin faults relative to the eastern ones indicates asymmetrical evolution of the rift as implied by the higher escarpments and accumulation of extensive, thick alluvial fans on the western margins of the rift. The thickness of the Quaternary sedimentary fill is more than 465 m, with clastic sediments intercalated with basaltic lavas. The Quaternary alkali basaltic volcanism accompanied fluvial to lacustrine sedimentation between 1.57 ± 0.08 and 0.05 ± 0.03 Ma. The faults are left-lateral oblique-slip faults as indicated by left-stepping faulting patterns, slip-lineation data and left-laterally offset lava flows and stream channels along the Karasu fault zone. At Hacılar village, an offset lava flow, dated to 0.08 ± 0.06 Ma, indicates a rate of left-lateral oblique slip of approximately 4.1 mm·year^–1. Overall, the Karasu Rift is an asymmetrical transtensional basin, which has developed between seismically active splays of the left-lateral DST and the left-lateral oblique-slip Karasu fault zone during the neotectonic period.     

Neotectonic and volcanic characteristics of the Karasu fault zone (Anatolia,Turkey): The transition zone between the Dead Sea transform and the East Anatolian fault zone

Abstract

The Karasu Rift (Antakya province, SE Turkey) has developed between east-dipping, NNE-striking faults of the Karasu fault zone, which define the western margin of the rift and westdipping, N-S to N20°-30°E-striking faults of Dead Sea Transform fault zone (DST) in the central part and eastern margin of the rift. The strand of the Karasu fault zone that bounds the basin from west forms a linkage zone between the DST and the East Anatolian fault zone (EAFZ). The greater vertical offset on the western margin faults relative to the eastern ones indicates asymmetrical evolution of the rift as implied by the higher escarpments and accumulation of extensive, thick alluvial fans on the western margins of the rift. The thickness of the Quaternary sedimentary fill is more than 465 m, with clastic sediments intercalated with basaltic lavas. The Quaternary alkali basaltic volcanism accompanied fluvial to lacustrine sedimentation between 1.57 ± 0.08 and 0.05 ± 0.03 Ma. The faults are left-lateral oblique-slip faults as indicated by left-stepping faulting patterns, slip-lineation data and left-laterally offset lava flows and stream channels along the Karasu fault zone. At Hacilar village, an offset lava flow, dated to 0.08 ± 0.06 Ma, indicates a rate of leftlateral oblique slip of approximately 4.1 mm?year^?1. Overall, the Karasu Rift is an asymmetrical transtensional basin, which has developed between seismically active splays of the left-lateral DST and the left-lateral oblique-slip Karasu fault zone during the neotectonic period. © 2001 Éditions scientifiques et médicales Elsevier SAS     

Late Cenozoic stress evolution along the Karasu Valley, SE Turkey

This study defines the Mio-Pliocene to present-day stress regime acting at the northeastern corner of the eastern Mediterranean region along the Karasu Valley (i.e., the Amanos Range), taking in the Antakya, Osmaniye and Kahramanmaras provinces. The inversion slip vectors measured on fault planes and chronologies between striations indicate that the stress regime varied from transpressional initially to transtensional, having consistent NW- and NE-trending σ_Hmax (σ₁) and σ_Hmin (σ₃) axes, respectively; there are significantly different mean stress-ratio (R_m) values however. The older mean stress state is characterized by N151±11°E-trending σ₁ and N59±12°E-trending σ₃ axes, and by a mean arithmetic R_m value of 0.76, indicating that the regional stress regime is transpressional. The younger stress regime is characterized by N154±8°E-trending σ₁ and N243±8°E-trending σ₃ axes, and by a mean arithmetic R_m value of 0.17, indicating a transtensional character for this regional stress regime. The low R values of the stress deviators related to the recent stress state reflect normal-component slips. The earthquake focal mechanism inversions confirm that the younger stress regime continues into the Recent. The inversion identifies a transtensional stress regime representing strike-slip and an extensional stress state with a consistent NE-trending σ_Hmin (σ₃) axis. These stress states are characterized by N66°E and N249°E-trending σ₃ axes, respectively. Both significant regional stress regimes induce left-lateral displacement along the southern part of the East Anatolian Fault (EAF, or Amanos Fault). The temporal change, probably in Quaternary time, within the regional stress regime—from transpression to transtension—resulted from the coeval influences of subduction processes in the west–southwest (i.e., along the Cyprus arc), continental collision in the east, and westward escape of the Anatolian block.     

Uplift and subsidence from oblique slip: the Ganos–Marmara bend of the North Anatolian Transform, western Turkey

Bends that locally violate plate-motion-parallel geometry are common structural elements of continental transform faults. We relate the vertical component of crustal motion in the western Marmara Sea region to the NNW-pointing 18° bend on the northern branch of the North Anatolian Fault (NAF-N) between the Ganos segment, which ruptured in 1912, and the central Marmara segment, a seismic gap. Crustal shortening and uplift on the transpressive west side of the bend results in the Ganos Mountain; crustal extension and subsidence on the transtensional east side produce the Tekirdağ Basin. We propose that this vertical component of deformation is controlled by oblique slip on the non-vertical north-dipping Ganos and Tekirdağ segments of the North Anatolian Fault. We compare Holocene with Quaternary structure across the bend using new and recently published data and conclude the following. First, bend-related vertical motion is occurring primarily north of the NAF-N. This suggests that this bend is fixed to the Anatolian side of the fault. Second, current deformation is consistent with an antisymmetric pattern centered at the bend, up on the west and down on the east. Accumulated deformation is shifted to the east along the right-lateral NAF-N, however, leading to locally opposite vertical components of long- and short-term motion. Uplift has started as far west as the landward extension of the Saros trough. Current subsidence is most intense close to the bend and to the Ganos Mountain, while the basin deepens gradually from the bend eastward for 28 km along the fault. The pattern of deformation is time-transgressive if referenced to the material, but is stable if referenced to the bend. The lag between motion and structure implies a 1.1–1.4 Ma age for the basin at current dextral slip rate (2.0–2.5 cm/year). Third, the Tekirdağ is an asymmetric basin progressively tilted down toward the NAF-N, which serves as the border fault. Progressive tilt suggests that the steep northward dip of the fault decreases with depth in a listric geometry at the scale of the upper crust and is consistent with reactivation of Paleogene suture-related thrust faults. Fourth, similar thrust-fault geometry west of the bend can account for the Ganos Mountain anticline/monocline as hanging-wall-block folding and back tilting. Oblique slip on a non-vertical master fault may accommodate transtension and transpression associated with other bends along the NAF and other continental transforms.     

The internal grabens of the Levant Rifts and their geodynamic significance

The Levant Rift system is a linear assemblage of rifts and their mountainous flanks that comprise three structural distinct sections. The southern Jordan Rift is built of series of secondary axial grabens that diminish in length northwards and are separated from each other by poorly rifted threshold zones. The central section of the rift system is the Lebanese Baqa’a embedded between mountainous flanks, and a splay of faults that scatter to the north-northeast; the northern section comprises the SW-trending Karasu–Hatay Rifts from which the Ghab graben branches southwards. It is suggested that the rifting of the Jordan Rift is the northern extension of the Red Sea continental break-up, while the Karasu–Tatay section correlates geodynamically with the migration of Anatolia westwards. The Baqa’a, its mountainous flanks and the fault splay mark the termination of the crustal break-up from the south, but rejuvenation of some faults indicate the effects of the Anatolian migration.     

From transpression to transtension: changes in morphology and structure around a bend on the North Anatolian Fault in the Marmara region

The east–west-trending North Anatolian Fault makes a 17° bend in the western Marmara region from a mildly transpressional segment to a strongly transtensional one. We have studied the changes in the morphology and structure around this fault bend using digital elevation models, field structural geology, and multi-channel seismic reflection profiles. The transpression is reflected in the morphology as the Ganos Mountain, a major zone of uplift, 10 km wide and 35 km long, elongated parallel to the transpressional Ganos Fault segment west of this bend. Flat-lying Eocene turbidites of the Thrace Basin are folded upwards against this Ganos Fault, forming a monocline with the Ganos Mountain at its steep southern limb and the flat-lying hinterland farther north at the flat limb. The sharp northern margin of the Ganos Mountain coincides closely with the monoclinal axis. The strike of the bedding, and the minor and regional fold axes in the Eocene turbidites in Ganos Mountain are parallel to the trace of the Ganos Fault indicating that these structures, as well as the morphology, have formed by shortening perpendicular to the North Anatolian Fault. The monoclinal structure of Ganos Mountain implies that the North Anatolian Fault dips under this mountain at 50°, and this ramp terminates at a decollement at a calculated depth of 8 km. East of this fault bend, the northward dip of the North Anatolian Fault is maintained but it has a normal dip-slip component. This has led to the formation of an asymmetric half-graben, the Tekirdağ Basin in the western Sea of Marmara, containing a thickness of up to 2.5 km of Pliocene to Recent syn-transform sediments. As the Ganos uplift is translated eastwards from the transpressional to the transtensional zone, it undergoes subsidence by southward tilting. However, a morphological relic of the Ganos uplift is maintained as the steep northern submarine slope of the Tekirdağ Basin. The minimum of 3.5 km of fault-normal shortening in the Ganos Mountain, and the minimum of 40 km eastward translation of the Ganos uplift indicate that the present fault geometry has existed for at least the last 2 million years.     

Newly found Tunglo Active Fault System in the fold and thrust belt in northwestern Taiwan deduced from deformed terraces and its tectonic significance

We found active faults in the fold and thrust belt between Tunglo town and the Tachia River in northwestern Taiwan. The surface rupture occurred in 1999 and 1935 nearby the study area, but no historical surface rupture is recorded in this area, suggesting that the seismic energy has been accumulated during the recent time. Deformed fluvial terraces aid in understanding late Quaternary tectonics in this tectonically active area. This area contains newly identified faults that we group as the Tunglo Fault System, which formed after the area's oldest fluvial terrace and appears at least 16 km long in roughly N–S orientation. Its progressive deformations are all recorded in associated terraces developed during the middle to late Quaternary. In the north, the system consists of two subparallel active faults, the Tunglo Fault and Tunglo East Fault, striking N–S and facing each other from opposite sides of the northward flowing Hsihu River, whose course may be controlled by interactions of above-mentioned two active faults. The northern part of the Tunglo Fault, to the west of the river, is a reverse fault with upthrown side on the west; conversely the Tunglo East Fault, to the east, is also a reverse fault, but with upthrown side on the east. Both faults are marked by a flexural scarp or eastward tilting of fluvial terraces. Considering a Quaternary syncline lies subparallel to the east of this fault system, the Tunglo Fault might be originated as a bending moment fault and the Tunglo East Fault as a flexural slip fault. However, they have developed as obvious reverse faults, which have progressive deformation under E–W compressive stress field of Taiwan. Farther south, a west-facing high scarp, the Tunglo South Fault, strikes NNE–SSW, oblique to the region's E–W direction of compression. Probably due to the strain partitioning, the Tunglo South Fault generates en echelon, elongated ridges and swales to accommodate right-lateral strike–slip displacement. Other structures in the area include eastward-striking portion of the Sanyi Fault, which has no evidence for late Quaternary surface rupture on this fault; perhaps slip on this part of Sanyi Fault ceased when the Tunglo Fault System became active.     

Geotechnical mapping for alluvial fan deposits controlled by active faults: a case study in the Erzurum,NE Turkey

Erzurum, the biggest city of Eastern Anatolia Region in the Turkey, is located in Karasu Plain. Karasu Plain, located on the central segment of the Erzurum Fault Zone, is an intermountain sedimentary basin with a Miocene-Quaternary volcanic basement, andesitic-basaltic lava flows and fissure eruptions of basaltic lava. It was filled in the early Quaternary by lacustrine fan-delta deposits. The basin is characterized by NNE-SSW trending sinistral wrench faults on its eastern margin and ENE-WSW trending reverse faults on its southern margin. Both systems of active faults intersect very near to Erzurum, which is considered to be the most likely site for the epicenter of a probable future large earthquake. Historical records of destructive earthquakes, morphotectonic features formed by paleo-seismic events and instrument seismic data of region indicate to a very high regional seismicity. The residential areas of Erzurum are located on thick alluvial fan deposits forming under the control of faults on the central segment of the Erzurum Fault Zone, which is one of the most active fault belts of the East Anatolian Region. Over time, the housing estates of city such as Yenisehir and Yildizkent have been expanded toward to the west and southwest part of Erzurum as a consequence of rapid and massive construction during the last 30 years. Geotechnical investigation has therefore been undertaken the residential areas of city in order to characterize geotechnical properties over the varied lithologies examine the potential for geotechnical mapping and assess the foundation conditions of the present and future settlement areas. The geological field observations and operations have been performed to make the soil sampling and characterize the lateral and vertical changes in thickness of the alluvial deposits in trenches, excavations and deep holes with 6–12 m sections. The soil samples have been subjected to a series of tests under laboratory conditions to obtain physical and mechanical properties. Furthermore, the standard penetration tests have been applied to the soils under field conditions. The geological field observations, geotechnical data and distribution of bearing capacity have been considered for the geotechnical mapping. Based on the geotechnical map, there are five geotechnical zones distinguished in the study area.     

Paleoseismology of the Palu–Lake Hazar segment of the East Anatolian Fault Zone, Turkey

The East Anatolian Fault Zone (EAFZ) is among the most important active continental transform fault zones in the world as testified by major historical and minor instrumental seismicity. The first paleoseismological exploratory trenching study on the EAFZ was done on the Palu–Lake Hazar segment (PLHS), which is one of the six segments forming the fault zone, in order to determine its past activity and to assess its earthquake hazard.The results of trenching indicate that the latest surface rupturing earthquakes on this segment may be the Ms=7.1+ 1874 and Ms=6.7 1875 events, and there were other destructive earthquakes prior to these events. The recurrence interval for a surface rupturing large (M>7) earthquake is estimated as minimum 100±35 and maximum 360 years. Estimates for the maximum possible paleoearthquake magnitude are (Mw) 7.1–7.7 for the Palu–Lake Hazar segment based on empirical magnitude fault rupture relations.An alluvial fan dated 14,475–15,255 cal years BP as well as another similar age fan with an abandoned stream channel on it are offset in a left-lateral sense 175 and 160.5 m, respectively, indicating an average slip rate of 11 mm/year. Because 127 years have elapsed since the last surface rupturing event, this slip rate suggests that 1.4 m of left-lateral strain has accumulated along the segment, ignoring possible creep effects, folding and other inelastic deformation. A 2.5 Ma age for the start of left-lateral movement on the segment, and in turn the EAFZ, is consistent with a slip rate of 11 mm/year and a previously reported 27 km total left-lateral offset. The cumulative 5–6 mm/year vertical slip rate near Lake Hazar suggests a possible age of 148–178 ka for the lake. Our trenching results indicate also that a significant fraction of the slip across the EAFZ zone is likely to be accommodated seismically. The present seismic quiescence compared with the past activity (paleoseismic and historic) indicate that the EAFZ may be “locked” and accumulating elastic strain energy but could move in the near future.     

Neotectonic deformation in the western sector of tectonic escape in Anatolia: palaeomagnetic study of the Afyon region, central Turkey

Following final closure of the Neotethyan Ocean during the late Miocene, deformation in central Turkey has led to crustal thickening and uplift to produce the Anatolian Plateau followed by westward extrusion of terranes by strike–slip. Widespread volcanism has accompanied this latter (neotectonic) phase, and palaeomagnetic study of the volcanism shows a coherent record of differential block rotations, indicating that the Anatolian region is not a plate (or ‘platelet’) sensu stricto but is undergoing distributed internal deformation. To evaluate the scale of neotectonic rotations in the transition zone near the western limit of tectonic escape and the border of the extensional domain in central-west Turkey, we have studied the palaeomagnetism at 82 sites in volcanic suites distributed along a 140-km lineament with north–south trend and ranging in age from 18 to 8 Ma. Comparable deflection of magnetic remanence from the present field direction is identified along the full length of the lineament. A mean clockwise rotation of 12.3±4.2° is determined for this western sector of the Anatolian strike–slip province. Since similar rotations are observed in the youngest and oldest units, this cumulative rotation occurred after the late Miocene. When interpreted together with results elsewhere in Anatolia, it is inferred that the rotation is later than crustal thickening and uplift of the Anatolian Plateau and entirely a facet of the tectonic escape. Inclinations are mostly 10° shallower than the predicted Miocene field and are considered to reflect the presence of a persistent inclination anomaly in the Mediterranean region. Larger rotations departing from the regional trend are also observed within the study region, but are confined to the vicinity of major faults, notably those bounding the Afyon-Ak ehir Graben.The pattern of neotectonic declinations across Anatolia identifies strong anticlockwise rotation in the east near the Arabian pincer with progressive reduction in the amount of rotation towards the west; it becomes zero or slightly clockwise at the western extremity of the accreted terrane collage. Rotations also appear to become generally younger towards the south. Crustal deformation has therefore been distributed, and the net effect of terrane extrusion to the west and south has been to expand the curvature of the Tauride Arc. The westward radial expansion of the extruded terranes is inferred to combine with backroll on the Hellenic Arc to produce the contemporary extensional province in western Turkey.     

Syntectonic crustal melting and high-grade metamorphism in a transpressional regime, Variscan Massif Central, France

Hot collisional orogens are characterized by abundant syn-kinematic granitic magmatism that profoundly affects their tectono-thermal evolutions. Voluminous granitic magmas, emplaced between 360 and 270 Ma, played a visibly important role in the evolution of the Variscan Orogen. In the Limousin region (western Massif Central, France), syntectonic granite plutons are spatially associated with major strike–slip shear zones that merge to the northwest with the South Armorican Shear Zone. This region allowed us to assess the role of magmatism in a hot transpressional orogen. Microstructural data and U/Pb zircon and monazite ages from a mylonitic leucogranite indicate synkinematic emplacement in a dextral transpressional shear zone at 313 ± 4 Ma. Leucogranites are coeval with cordierite-bearing migmatitic gneisses and vertical lenses of leucosome in strike–slip shear zones. We interpret U/Pb monazite ages of 315 ± 4 Ma for the gneisses and 316 ± 2 Ma for the leucosomes as the minimum age of high-grade metamorphism and migmatization respectively. These data suggest a spatial and temporal relationship between transpression, crustal melting, rapid exhumation and magma ascent, and cooling of high-grade metamorphic rocks.Some granites emplaced in the strike–slip shear zone are bounded at their roof by low dip normal faults that strike N–S, perpendicular to the E–W trend of the belt. The abundant crustal magmatism provided a low-viscosity zone that enhanced Variscan orogenic collapse during continued transpression, inducing the development of normal faults in the transpression zone and thrust faults at the front of the collapsed orogen.     

Review of the tectonics of the Levant Rift system: the structural significance of oblique continental breakup

The Levant Rift system is an elongated series of structural basins that extends for more than 1000 km from the northern Red Sea to southern Anatolia. The system consists of three major segments, the Jordan Rift in the south, El Gharb–Kara-Su Rift in the north, and the Lebanese Fault splay in between. The rifted parts of this structural system are accompanied by intensively uplifted margins that mirror-image the basinal pattern, namely, the deeper the basin—the higher its margins, and vice versa. Uplifts also occur along the fault splay section. The Jordan Rift comprises axial basins that diminish in size from the south northwards, and are separated from each other by shallow threshold zones along the axis of the rift, where the margins are also subdued. The Lebanese Fault splay consists of five faults that emerge from the northern edge of the Jordan Rift and trend like a fan between the north and the northeast. One of these faults connects the Jordan and El Gharb–Kara-Su rifts. The Levant Rift and its uplifted margins started to develop in the middle-late Miocene, and most of the structural development occurred in the Plio-Pleistocene.The Levant Rift system is characterized by its oblique displacement, and evidence for both dip-slip and strike-slip displacement was measured on its faults. Earthquakes also indicate that same mixed pattern, some of them show strike-slip offset, and others normal. It is generally conceded that the amount of normal offset along the boundary faults of the Rift system reaches 8–10 km, but the lateral displacement is disputed, and offsets ranging from 11 to 107 km were suggested. Assessment of the available data led us to suggest that the sinistral offset along the Levant Rift system is approximately 10–20 km. The similarity between the vertical and the lateral displacements, the basin and threshold structural pattern of the Rift, model experiments in oblique rifting, as well as the significant tectonic resemblance to the Red Sea and the East African rifts, indicate that the Levant Rift is the product of continental breakup, and it is probably an emerging oceanic spreading center.     

The Role of Pre-existing Structures in the Origin, Propagation and Architecture of Faults in the Main Ethiopian Rift

Four major fault systems oriented N–S to NNE–SSW, NE–SW, E–W and NW–SE are identified from Landsat Thematic Mapper (TM) images and a high resolution digital elevation model (DEM) over the Ethiopian Rift Valley and the surrounding plateaus. Most of these faults are the result of Cenozoic - extensional reactivation of pre-existing basement structures. These faults interacted with each other at different geological times under different geodynamic conditions. The Cenozoic interaction under an extensional tectonic regime is the major cause of the actual volcano-tectonic landscape in Ethiopia. The Wonji Fault Belt (WFB), which comprises the N–S to NNE–SSW striking rift floor faults, displays peculiar propagation patterns mainly due to interaction with the other fault systems and the influence of underlying basement structures. The commonly observed patterns are: curvilinear oblique-slip faults forming lip-horsts, sinusoidal faults, intersecting faults and locally splaying faults at their ends. Fault-related open structures such as tail-cracks, releasing bends and extensional relay zones and fault intersections have served as principal eruption sites for monogenetic Plio-Quaternary volcanoes in the Main Ethiopian Rift (MER).     

Neotectonics of Turkey – a synthesis

Turkey forms one of the most actively deforming regions in the world and has a long history of devastating earthquakes. The better understanding of its neotectonic features and active tectonics would provide insight, not only for the country but also for the entire Eastern Mediterranean region. Active tectonics of Turkey is the manifestation of collisional intracontinental convergence- and tectonic escape-related deformation since the Early Pliocene (∼5 Ma). Three major structures govern the neotectonics of Turkey; they are dextral North Anatolian Fault Zone (NAFZ), sinistral East Anatolian Fault Zone (EAFZ) and the Aegean–Cyprean Arc. Also, sinistral Dead Sea Fault Zone has an important role. The Anatolian wedge between the NAFZ and EAFZ moves westward away from the eastern Anatolia, the collision zone between the Arabian and the Eurasian plates. Ongoing deformation along, and mutual interaction among them has resulted in four distinct neotectonic provinces, namely the East Anatolian contractional, the North Anatolian, the Central Anatolian ‘Ova’ and the West Anatolian extensional provinces. Each province is characterized by its unique structural elements, and forms an excellent laboratory to study active strike-slip, normal and reverse faulting and the associated basin formation.     

Evidence for coupled reverse and normal active faulting in W Iberia: The Vidigueira–Moura and Alqueva faults (SE Portugal)

The Vidigueira–Moura fault (VMF) is a 65 km long, E–W trending, N dipping reverse left-lateral late Variscan structure located in SE Portugal (W Iberia), which has been reactivated during the Cenozoic with reverse right-lateral slip. It is intersected by, and interferes with the NE–SW trending Alentejo–Plasencia fault. East of this intersection, for a length of 40 km the VMF borders an intracratonic tectonic basin on its northern side, thrusting Paleozoic schists, meta-volcanics and granites, on the north, over Cenozoic continental sediments preserved in the basin, on the south. West of the faults intersection, evidence of Cenozoic reactivation is scarce. In the eastern sector, Plio-Quaternary VMF reactivation is indicated by geomorphologic, stratigraphic, and structural data, showing reverse movement with a right-lateral strike-slip component, in response to a NW–SE trending compressive stress. An average vertical displacement rate of 0.06 to 0.08 mm/yr since late Pliocene (roughly the last 2.5 Ma) is estimated. The Alqueva fault (AF) is a subparallel, northward dipping, 7.5 km long anastomosing fault zone that affects Palaeozoic basement rocks, and is located 2.5 km north and on the hanging block of the VMF. The AF is also a reverse left-lateral late Variscan structure, which has been reactivated during the Tertiary with reverse right-lateral slip; however, Plio-Quaternary reactivation was normal left-lateral, as shown by abundant kinematical criteria (slickensides) and geomorphic evidence. It shows an average displacement rate of 0.02 mm/yr for the vertical component of movement in the approximately last 2.5 Ma. It is proposed that the normal displacements on the AF result from tangential longitudinal strain on the upthrown block of the VMF above a convex ramp of this main reverse structure. According to this model of faults interaction, the AF is interpreted to work as a bending-moment fault sited above the VMF thrust ramp. Consequently, it is expected that the displacements on the AF increase towards the topographic surface with the increase in the imposed extension, declining downwards until they vanish above or at the VMF ramp. In order to constrain the proposed scheme, numerical modeling was performed, aiming at the reproduction of the present topography across the faults using different geodynamic models and fault geometries and displacements.     

Experimental evidence for the dynamics of the formation of the Yinggehai basin, NW South China Sea

The Yinggehai basin is located on the northwestern shelf of the South China Sea. It is the seaward elongation of the Red River Fault Zone (RRFZ). The orientation and rift shape of the Yinggehai basin are mainly controlled by NW-, NNW- and nearly NS-trending basal faults. The depocenter migrated southeastward when the basin developed. The depocenter trended northwest before about 36 Ma, then jumped southward and became nearly N–S trending and migrated toward the southeast up to 21 Ma; thereafter, the depocenter trended northwest again. Based on above and structural evolution in neighbor areas, it is believed that the Yinggehai basin formation was mainly controlled by the extrusion accompanied by clockwise rotation of Indochina. We set up analogue models (thin basal plate model and thick basal plate model) to investigate the evolution of Yinggehai basin. From the experiments, we consider that the basin evolution was related to the extrusion and clockwise rotation of the Indochina block, which was caused by the collision of the Indian plate and Tibet. This process took place in four main stages: (1) Slow rifting stage (before 36 Ma) with a NW-trending depocenter; (2) rifting stage formed by sinistral slip of the Indochina block accompanied by rapid clockwise rotation between 36 and 21 Ma; (3) rifting-thermal subsidence stage affected by sinistral slip of the Indochina (21–5 Ma) block and (4) dextral strike–slip (5–0 Ma).     

Late Quaternary activity of the Feldbiss Fault Zone, Roer Valley Rift System, the Netherlands, based on displaced fluvial terrace fragments

The Meuse River crosses the Feldbiss Fault Zone, one of the main border fault zones of the Roer Valley Graben in the southern part of the Netherlands. Uplift of the area south of the Feldbiss Fault Zone forced the Meuse River to incise and, as a result, a flight of terraces was formed. Faults of the Feldbiss Fault Zone have displaced the Middle and Late Pleistocene terrace deposits. In this study, an extensive geomorphological survey was carried out to locate the faults of the Feldbiss Fault Zone and to determine the displacement history of terrace deposits.The Feldbiss Fault Zone is characterized by an average displacement rate of 0.041–0.047 mm a⁻¹ during the Late Pleistocene. Individual faults show an average displacement rate ranging between 0.010 and 0.034 mm a⁻¹. The spatial variation in displacement rates along the individual faults reveals a system of overstepping faults. These normal faults developed by reactivation of Paleozoic strike-slip faults.As fault displacements at the bases of the younger terrace deposits are apparently similar to the tops of the adjacent older terrace, the age of these horizons is the same within thousands of years. This implies that the model of terrace development by rapid fluvial incision followed by slow aggradation does apply for this area.     

Mantle flow-induced crustal thinning in the area between the easternmost part of the Anatolian plate and the Arabian Foreland (E Turkey) deduced from the geological and geophysical data

Eastern Anatolia consisting of an amalgamation of fragments of oceanic and continental lithosphere is a current active intercontinental contractional zone that is still being squeezed and shortened between the Arabian and Eurasian plates. This collisional and contractional zone is being accompanied by the tectonic escape of most of the Anatolian plate to the west by major strike-slip faulting on the right-lateral North Anatolian Transform Fault Zone (NATFZ) and left-lateral East Anatolian Transform Fault Zone (EATFZ) which meet at Karlıova forming an east-pointing cusp. The present-day crust in the area between the easternmost part of the Anatolian plate and the Arabian Foreland gets thinner from north (ca 44 km) to south (ca 36 km) relative to its eastern (EAHP) and western sides (central Anatolian region). This thinner crustal area is characterized by shallow CPD (12–16 km), very low Pn velocities (< 7.8 km/s) and high Sn attenuation which indicate partially molten to eroded mantle lid or occurrence of asthenospheric mantle beneath the crust. Northernmost margin of the Arabian Foreland in the south of the Bitlis–Pötürge metamorphic gap area is represented by moderate CPD (16–18 km) relative to its eastern and western sides, and low Pn velocities (8 km/s). We infer from the geophysical data that the lithospheric mantle gets thinner towards the Bitlis–Pötürge metamorphic gap area in the northern margin of the Arabian Foreland which has been most probably caused by mechanical removal of the lithospheric mantle during mantle invasion to the north following the slab breakoff beneath the Bitlis–Pötürge Suture Zone. Mantle flow-driven rapid extrusion and counterclockwise rotation of the Anatolian plate gave rise to stretching and hence crustal thinning in the area between the easternmost part of the Anatolian plate and the Arabian Foreland which is currently dominated by wrench tectonics.